arm64/boot: Disable trapping of PMZR_EL0 writes to EL2grafted

__init_el2_fgt2() writes one mask to both HDFGRTR2_EL2 and HDFGWTR2_EL2.
PMZR_EL0 is write-only, so its trap bit, nPMZR_EL0, exists only in
HDFGWTR2_EL2 and is therefore never set: a PMZR_EL0 write from the host
traps to EL2, where the nVHE hypervisor has no handler and BUG()s. The
kernel never writes PMZR_EL0, but kernel.perf_user_access=1 has the PMU
driver set PMUSERENR_EL0.UEN for a task with a user-read event, so a
write from EL0 reaches the trap and takes the host down without a panic
message.

Accumulate the HDFGWTR2_EL2 bits separately, as __init_el2_fgt() already
does for HDFGWTR_EL2, and set nPMZR_EL0 with the other FEAT_PMUv3p9
bits.

Fixes: 858c7bfcb35e1 ("arm64/boot: Enable EL2 requirements for FEAT_PMUv3p9")
Cc: stable@vger.kernel.org
Signed-off-by: Fuad Tabba <fuad.tabba@linux.dev>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Oliver Upton <oupton@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>

1 files changed, 51 insertions, 0 deletions

diff --git a/drivers/usb/common/Kconfig b/drivers/usb/common/Kconfig
new file mode 100644
index 000000000..b85662243
--- /dev/null
+++ b/drivers/usb/common/Kconfig
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: GPL-2.0
+
+config USB_COMMON
+	tristate
+
+
+config USB_LED_TRIG
+	bool "USB LED Triggers"
+	depends on LEDS_CLASS && USB_COMMON && LEDS_TRIGGERS
+	help
+	  This option adds LED triggers for USB host and/or gadget activity.
+
+	  Say Y here if you are working on a system with led-class supported
+	  LEDs and you want to use them as activity indicators for USB host or
+	  gadget.
+
+config USB_ULPI_BUS
+	tristate "USB ULPI PHY interface support"
+	select USB_COMMON
+	help
+	  UTMI+ Low Pin Interface (ULPI) is specification for a commonly used
+	  USB 2.0 PHY interface. The ULPI specification defines a standard set
+	  of registers that can be used to detect the vendor and product which
+	  allows ULPI to be handled as a bus. This module is the driver for that
+	  bus.
+
+	  The ULPI interfaces (the buses) are registered by the drivers for USB
+	  controllers which support ULPI register access and have ULPI PHY
+	  attached to them. The ULPI PHY drivers themselves are normal PHY
+	  drivers.
+
+	  ULPI PHYs provide often functions such as ADP sensing/probing (OTG
+	  protocol) and USB charger detection.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called ulpi.
+
+config USB_CONN_GPIO
+	tristate "USB GPIO Based Connection Detection Driver"
+	depends on GPIOLIB
+	select USB_ROLE_SWITCH
+	select POWER_SUPPLY
+	help
+	  The driver supports USB role switch between host and device via GPIO
+	  based USB cable detection, used typically if an input GPIO is used
+	  to detect USB ID pin, and another input GPIO may be also used to detect
+	  Vbus pin at the same time, it also can be used to enable/disable
+	  device if an input GPIO is only used to detect Vbus pin.
+
+	  To compile the driver as a module, choose M here: the module will
+	  be called usb-conn-gpio.ko