From 2bc6b218717b9d08f466f88209251d54bc09b207 Mon Sep 17 00:00:00 2001 From: Fuad Tabba Date: Tue, 22 Sep 2026 19:14:30 +0100 Subject: arm64/boot: Disable trapping of PMZR_EL0 writes to EL2 __init_el2_fgt2() writes one mask to both HDFGRTR2_EL2 and HDFGWTR2_EL2. PMZR_EL0 is write-only, so its trap bit, nPMZR_EL0, exists only in HDFGWTR2_EL2 and is therefore never set: a PMZR_EL0 write from the host traps to EL2, where the nVHE hypervisor has no handler and BUG()s. The kernel never writes PMZR_EL0, but kernel.perf_user_access=1 has the PMU driver set PMUSERENR_EL0.UEN for a task with a user-read event, so a write from EL0 reaches the trap and takes the host down without a panic message. Accumulate the HDFGWTR2_EL2 bits separately, as __init_el2_fgt() already does for HDFGWTR_EL2, and set nPMZR_EL0 with the other FEAT_PMUv3p9 bits. Fixes: 858c7bfcb35e1 ("arm64/boot: Enable EL2 requirements for FEAT_PMUv3p9") Cc: stable@vger.kernel.org Signed-off-by: Fuad Tabba Reviewed-by: Anshuman Khandual Reviewed-by: Oliver Upton Signed-off-by: Will Deacon --- drivers/usb/common/Kconfig | 51 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 51 insertions(+) create mode 100644 drivers/usb/common/Kconfig (limited to 'drivers/usb/common/Kconfig') diff --git a/drivers/usb/common/Kconfig b/drivers/usb/common/Kconfig new file mode 100644 index 000000000..b85662243 --- /dev/null +++ b/drivers/usb/common/Kconfig @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: GPL-2.0 + +config USB_COMMON + tristate + + +config USB_LED_TRIG + bool "USB LED Triggers" + depends on LEDS_CLASS && USB_COMMON && LEDS_TRIGGERS + help + This option adds LED triggers for USB host and/or gadget activity. + + Say Y here if you are working on a system with led-class supported + LEDs and you want to use them as activity indicators for USB host or + gadget. + +config USB_ULPI_BUS + tristate "USB ULPI PHY interface support" + select USB_COMMON + help + UTMI+ Low Pin Interface (ULPI) is specification for a commonly used + USB 2.0 PHY interface. The ULPI specification defines a standard set + of registers that can be used to detect the vendor and product which + allows ULPI to be handled as a bus. This module is the driver for that + bus. + + The ULPI interfaces (the buses) are registered by the drivers for USB + controllers which support ULPI register access and have ULPI PHY + attached to them. The ULPI PHY drivers themselves are normal PHY + drivers. + + ULPI PHYs provide often functions such as ADP sensing/probing (OTG + protocol) and USB charger detection. + + To compile this driver as a module, choose M here: the module will + be called ulpi. + +config USB_CONN_GPIO + tristate "USB GPIO Based Connection Detection Driver" + depends on GPIOLIB + select USB_ROLE_SWITCH + select POWER_SUPPLY + help + The driver supports USB role switch between host and device via GPIO + based USB cable detection, used typically if an input GPIO is used + to detect USB ID pin, and another input GPIO may be also used to detect + Vbus pin at the same time, it also can be used to enable/disable + device if an input GPIO is only used to detect Vbus pin. + + To compile the driver as a module, choose M here: the module will + be called usb-conn-gpio.ko -- cgit v1.3.1