selftests/bpf: Reject graph kptr use after RCU unlockgrafted

Add a sleepable verifier test that loads a graph-node local kptr in an
explicit RCU read-side critical section, then passes its node to
bpf_rbtree_remove() after the section ends.

Before the verifier fix, the stale NON_OWN_REF flag makes the node look like
a live borrowed reference and the program is accepted. After the fix, the
pointer is demoted without NON_OWN_REF and the graph kfunc argument is
rejected.

Also exercise a graph kptr loaded while a spin lock provides implicit RCU
protection. The pointer must be invalidated when the lock is released, which
guards the required ordering between non-owning-reference invalidation and
RCU demotion.

Update the existing fault-protected load test state description. The
post-unlock pointer no longer carries NON_OWN_REF, but remains readable
because the load is rewritten to use BPF_PROBE_MEM.

Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20260904084325.52250-7-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

1 files changed, 64 insertions, 0 deletions

diff --git a/drivers/dma/ti/Kconfig b/drivers/dma/ti/Kconfig
new file mode 100644
index 000000000..cbc30ab62
--- /dev/null
+++ b/drivers/dma/ti/Kconfig
@@ -0,0 +1,64 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Texas Instruments DMA drivers
+#
+
+config TI_CPPI41
+	tristate "Texas Instruments CPPI 4.1 DMA support"
+	depends on (ARCH_OMAP || ARCH_DAVINCI_DA8XX)
+	select DMA_ENGINE
+	help
+	  The Communications Port Programming Interface (CPPI) 4.1 DMA engine
+	  is currently used by the USB driver on AM335x and DA8xx platforms.
+
+config TI_EDMA
+	tristate "Texas Instruments EDMA support"
+	depends on ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE || COMPILE_TEST
+	select DMA_ENGINE
+	select DMA_VIRTUAL_CHANNELS
+	select TI_DMA_CROSSBAR if (ARCH_OMAP || COMPILE_TEST)
+	default ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE
+	help
+	  Enable support for the TI EDMA (Enhanced DMA) controller. This DMA
+	  engine is found on TI DaVinci, AM33xx, AM43xx, DRA7xx and Keystone 2
+	  parts.
+
+config DMA_OMAP
+	tristate "Texas Instruments sDMA (omap-dma) support"
+	depends on ARCH_OMAP || COMPILE_TEST
+	select DMA_ENGINE
+	select DMA_VIRTUAL_CHANNELS
+	select TI_DMA_CROSSBAR if (SOC_DRA7XX || COMPILE_TEST)
+	default ARCH_OMAP
+	help
+	  Enable support for the TI sDMA (System DMA or DMA4) controller. This
+	  DMA engine is found on OMAP and DRA7xx parts.
+
+config TI_K3_UDMA
+	tristate "Texas Instruments UDMA support"
+	depends on ARCH_K3 || COMPILE_TEST
+	depends on TI_SCI_PROTOCOL
+	depends on TI_SCI_INTA_IRQCHIP
+	select DMA_ENGINE
+	select DMA_VIRTUAL_CHANNELS
+	select SOC_TI
+	select TI_K3_RINGACC
+	select TI_K3_PSIL
+        help
+	  Enable support for the TI UDMA (Unified DMA) controller. This
+	  DMA engine is used in AM65x and j721e.
+
+config TI_K3_UDMA_GLUE_LAYER
+	tristate "Texas Instruments UDMA Glue layer for non DMAengine users"
+	depends on ARCH_K3 || COMPILE_TEST
+	depends on TI_K3_UDMA
+	help
+	  Say y here to support the K3 NAVSS DMA glue interface
+	  If unsure, say N.
+
+config TI_K3_PSIL
+       tristate
+       default TI_K3_UDMA
+
+config TI_DMA_CROSSBAR
+	bool