From 6668ed271eaefaa63e686bdfbedaeb7b8e492722 Mon Sep 17 00:00:00 2001 From: Kumar Kartikeya Dwivedi Date: Fri, 4 Sep 2026 10:43:19 +0200 Subject: selftests/bpf: Reject graph kptr use after RCU unlock Add a sleepable verifier test that loads a graph-node local kptr in an explicit RCU read-side critical section, then passes its node to bpf_rbtree_remove() after the section ends. Before the verifier fix, the stale NON_OWN_REF flag makes the node look like a live borrowed reference and the program is accepted. After the fix, the pointer is demoted without NON_OWN_REF and the graph kfunc argument is rejected. Also exercise a graph kptr loaded while a spin lock provides implicit RCU protection. The pointer must be invalidated when the lock is released, which guards the required ordering between non-owning-reference invalidation and RCU demotion. Update the existing fault-protected load test state description. The post-unlock pointer no longer carries NON_OWN_REF, but remains readable because the load is rewritten to use BPF_PROBE_MEM. Signed-off-by: Kumar Kartikeya Dwivedi Link: https://lore.kernel.org/r/20260904084325.52250-7-memxor@gmail.com Signed-off-by: Alexei Starovoitov --- drivers/dma/ti/Kconfig | 64 ++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 64 insertions(+) create mode 100644 drivers/dma/ti/Kconfig (limited to 'drivers/dma/ti/Kconfig') diff --git a/drivers/dma/ti/Kconfig b/drivers/dma/ti/Kconfig new file mode 100644 index 000000000..cbc30ab62 --- /dev/null +++ b/drivers/dma/ti/Kconfig @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: GPL-2.0-only +# +# Texas Instruments DMA drivers +# + +config TI_CPPI41 + tristate "Texas Instruments CPPI 4.1 DMA support" + depends on (ARCH_OMAP || ARCH_DAVINCI_DA8XX) + select DMA_ENGINE + help + The Communications Port Programming Interface (CPPI) 4.1 DMA engine + is currently used by the USB driver on AM335x and DA8xx platforms. + +config TI_EDMA + tristate "Texas Instruments EDMA support" + depends on ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE || COMPILE_TEST + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + select TI_DMA_CROSSBAR if (ARCH_OMAP || COMPILE_TEST) + default ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE + help + Enable support for the TI EDMA (Enhanced DMA) controller. This DMA + engine is found on TI DaVinci, AM33xx, AM43xx, DRA7xx and Keystone 2 + parts. + +config DMA_OMAP + tristate "Texas Instruments sDMA (omap-dma) support" + depends on ARCH_OMAP || COMPILE_TEST + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + select TI_DMA_CROSSBAR if (SOC_DRA7XX || COMPILE_TEST) + default ARCH_OMAP + help + Enable support for the TI sDMA (System DMA or DMA4) controller. This + DMA engine is found on OMAP and DRA7xx parts. + +config TI_K3_UDMA + tristate "Texas Instruments UDMA support" + depends on ARCH_K3 || COMPILE_TEST + depends on TI_SCI_PROTOCOL + depends on TI_SCI_INTA_IRQCHIP + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + select SOC_TI + select TI_K3_RINGACC + select TI_K3_PSIL + help + Enable support for the TI UDMA (Unified DMA) controller. This + DMA engine is used in AM65x and j721e. + +config TI_K3_UDMA_GLUE_LAYER + tristate "Texas Instruments UDMA Glue layer for non DMAengine users" + depends on ARCH_K3 || COMPILE_TEST + depends on TI_K3_UDMA + help + Say y here to support the K3 NAVSS DMA glue interface + If unsure, say N. + +config TI_K3_PSIL + tristate + default TI_K3_UDMA + +config TI_DMA_CROSSBAR + bool -- cgit v1.3.1