iio: proximity: vl53l0x-i2c: claim direct mode for raw readsgrafted

vl53l0x_read_raw() starts a single-shot ranging measurement and reads
back the result. Once the triggered buffer is enabled the sensor runs in
continuous mode and its data-ready interrupt is routed to the trigger,
so a concurrent in_distance_raw read disturbs the streaming setup and
never gets its completion, returning -ETIMEDOUT.

The original submission claimed direct mode here, but it was dropped
during review because the driver had no buffer support at the time [1].
Continuous (buffered) mode was later added without restoring the
claim [2], reintroducing the conflict.

Reject direct reads while buffered capture is active by claiming direct
mode around the measurement, as the vl53l1x sibling already does.

Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support")
Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1]
Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2]
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

1 files changed, 53 insertions, 0 deletions

diff --git a/Documentation/usb/dwc3.rst b/Documentation/usb/dwc3.rst
new file mode 100644
index 000000000..f94a7ba16
--- /dev/null
+++ b/Documentation/usb/dwc3.rst
@@ -0,0 +1,53 @@
+===========
+DWC3 driver
+===========
+
+
+TODO
+~~~~
+
+Please pick something while reading :)
+
+- Convert interrupt handler to per-ep-thread-irq
+
+  As it turns out some DWC3-commands ~1ms to complete. Currently we spin
+  until the command completes which is bad.
+
+  Implementation idea:
+
+  - dwc core implements a demultiplexing irq chip for interrupts per
+    endpoint. The interrupt numbers are allocated during probe and belong
+    to the device. If MSI provides per-endpoint interrupt this dummy
+    interrupt chip can be replaced with "real" interrupts.
+  - interrupts are requested / allocated on usb_ep_enable() and removed on
+    usb_ep_disable(). Worst case are 32 interrupts, the lower limit is two
+    for ep0/1.
+  - dwc3_send_gadget_ep_cmd() will sleep in wait_for_completion_timeout()
+    until the command completes.
+  - the interrupt handler is split into the following pieces:
+
+    - primary handler of the device
+      goes through every event and calls generic_handle_irq() for event
+      it. On return from generic_handle_irq() in acknowledges the event
+      counter so interrupt goes away (eventually).
+
+    - threaded handler of the device
+      none
+
+    - primary handler of the EP-interrupt
+      reads the event and tries to process it. Everything that requires
+      sleeping is handed over to the Thread. The event is saved in an
+      per-endpoint data-structure.
+      We probably have to pay attention not to process events once we
+      handed something to thread so we don't process event X prio Y
+      where X > Y.
+
+    - threaded handler of the EP-interrupt
+      handles the remaining EP work which might sleep such as waiting
+      for command completion.
+
+  Latency:
+
+   There should be no increase in latency since the interrupt-thread has a
+   high priority and will be run before an average task in user land
+   (except the user changed priorities).