Merge tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlgrafted

Pull pin control updates from Linus Walleij:
 "Core changes:

   - Use the non-blocking mux_state_try_select() in the generic MUX pin
     control back-end

   - Free pin maps on pinctrl_generic_to_map() failure in the core
     helpers

  New hardware pin control:

   - Qualcomm Maili TLMM SoC, PMG1110 PMIC, and Eliza LPASS LPI TLMM SoC
     (this is for the low power audio, LPASS = Low Power Audio SubSystem
     portions)

   - Upboard support on top of the Intel pin controller

   - Apple T6030 and T6031 support (just compatible strings)

   - Samsung Exynos 8855 SoC

   - Mediatek MT6858 SoC

   - Rockchip RK3308B and RV1106 SoCs

   - Airoha EN7523 and AN7563 SoCs

  Improvements:

   - Qualcomm TLMM GPIOs are unconditionally marked as wakeup capable

   - Qualcomm improvements on top of the Qualcomm PDC (power domain
     controller) irqchip improvements from tglx:s tree

   - Qualcomm IPQ806x and IPQ9650 non-urgent pin grop fixups

   - The NPCM8xx driver has been put into shape fixing many pin and
     group definitions

   - Some non-urgent Tegra 264 pin assignments are fixed up

   - Some non-urgent fixups to Airoha AN7581 and AN7583 registers and
     pin assignments, missing features etc"

* tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (130 commits)
  dt-bindings: pinctrl: Convert TI DA850 pupd to DT schema
  pinctrl: meson: sync some modify from A4
  pinctrl: meson: a4: Add input enable pin configuration
  pinctrl: realtek: rtd1625: remove unused group name spdif_sel
  pinctrl: realtek: rtd1625: fix base_bit for VE4 GPIO 13
  dt-bindings: pinctrl: microchip,pic32mzda-pinctrl: Convert to DT schema
  Revert "Merge branch 'ib-rsk7204' into devel"
  pinctrl: rockchip: Add RV1106 pinctrl support
  dt-bindings: pinctrl: rockchip: Add RV1106 compatible
  pinctrl: rockchip: Decode drive strength in the get function
  pinctrl: fix PINCTRL_GENERIC_MUX not always being selectable
  pinctrl: airoha: add support of an7563 SoC
  dt-bindings: pinctrl: airoha: add support of an7563 pin controller
  pinctrl: airoha: try to find chip scu node by phandle first
  pinctrl: airoha: add support of en7523 SoC
  dt-bindings: pinctrl: airoha: add support of en7523 pin controller
  pinctrl: airoha: an7583: add support for olt pinmux
  pinctrl: airoha: an7583: add support for pon_alt pinmux
  pinctrl: airoha: an7583: add support for npu_uart pinmux
  dt-bindings: pinctrl: airoha: an7583: add missed features
  ...

1 files changed, 62 insertions, 0 deletions

diff --git a/Documentation/trace/sys-t.rst b/Documentation/trace/sys-t.rst
new file mode 100644
index 000000000..3d8eb9273
--- /dev/null
+++ b/Documentation/trace/sys-t.rst
@@ -0,0 +1,62 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===================
+MIPI SyS-T over STP
+===================
+
+The MIPI SyS-T protocol driver can be used with STM class devices to
+generate standardized trace stream. Aside from being a standard, it
+provides better trace source identification and timestamp correlation.
+
+In order to use the MIPI SyS-T protocol driver with your STM device,
+first, you'll need CONFIG_STM_PROTO_SYS_T.
+
+Now, you can select which protocol driver you want to use when you create
+a policy for your STM device, by specifying it in the policy name:
+
+# mkdir /config/stp-policy/dummy_stm.0:p_sys-t.my-policy/
+
+In other words, the policy name format is extended like this:
+
+  <device_name>:<protocol_name>.<policy_name>
+
+With Intel TH, therefore it can look like "0-sth:p_sys-t.my-policy".
+
+If the protocol name is omitted, the STM class will chose whichever
+protocol driver was loaded first.
+
+You can also double check that everything is working as expected by
+
+# cat /config/stp-policy/dummy_stm.0:p_sys-t.my-policy/protocol
+p_sys-t
+
+Now, with the MIPI SyS-T protocol driver, each policy node in the
+configfs gets a few additional attributes, which determine per-source
+parameters specific to the protocol:
+
+# mkdir /config/stp-policy/dummy_stm.0:p_sys-t.my-policy/default
+# ls /config/stp-policy/dummy_stm.0:p_sys-t.my-policy/default
+channels
+clocksync_interval
+do_len
+masters
+ts_interval
+uuid
+
+The most important one here is the "uuid", which determines the UUID
+that will be used to tag all data coming from this source. It is
+automatically generated when a new node is created, but it is likely
+that you would want to change it.
+
+do_len switches on/off the additional "payload length" field in the
+MIPI SyS-T message header. It is off by default as the STP already
+marks message boundaries.
+
+ts_interval and clocksync_interval determine how much time in milliseconds
+can pass before we need to include a protocol (not transport, aka STP)
+timestamp in a message header or send a CLOCKSYNC packet, respectively.
+
+See Documentation/ABI/testing/configfs-stp-policy-p_sys-t for more
+details.
+
+* [1] https://www.mipi.org/specifications/sys-t