iio: proximity: vl53l0x-i2c: claim direct mode for raw readsgrafted

vl53l0x_read_raw() starts a single-shot ranging measurement and reads
back the result. Once the triggered buffer is enabled the sensor runs in
continuous mode and its data-ready interrupt is routed to the trigger,
so a concurrent in_distance_raw read disturbs the streaming setup and
never gets its completion, returning -ETIMEDOUT.

The original submission claimed direct mode here, but it was dropped
during review because the driver had no buffer support at the time [1].
Continuous (buffered) mode was later added without restoring the
claim [2], reintroducing the conflict.

Reject direct reads while buffered capture is active by claiming direct
mode around the measurement, as the vl53l1x sibling already does.

Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support")
Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1]
Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2]
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

1 files changed, 78 insertions, 0 deletions

diff --git a/Documentation/networking/ipv6.rst b/Documentation/networking/ipv6.rst
new file mode 100644
index 000000000..ba09c2f2d
--- /dev/null
+++ b/Documentation/networking/ipv6.rst
@@ -0,0 +1,78 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+====
+IPv6
+====
+
+
+Options for the ipv6 module are supplied as parameters at load time.
+
+Module options may be given as command line arguments to the insmod
+or modprobe command, but are usually specified in either
+``/etc/modules.d/*.conf`` configuration files, or in a distro-specific
+configuration file.
+
+The available ipv6 module parameters are listed below.  If a parameter
+is not specified the default value is used.
+
+The parameters are as follows:
+
+disable
+
+	Specifies whether to load the IPv6 module, but disable all
+	its functionality.  This might be used when another module
+	has a dependency on the IPv6 module being loaded, but no
+	IPv6 addresses or operations are desired.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 is enabled.
+
+		This is the default value.
+
+	1
+		IPv6 is disabled.
+
+		No IPv6 addresses will be added to interfaces, and
+		it will not be possible to open an IPv6 socket.
+
+		A reboot is required to enable IPv6.
+
+autoconf
+
+	Specifies whether to enable IPv6 address autoconfiguration
+	on all interfaces.  This might be used when one does not wish
+	for addresses to be automatically generated from prefixes
+	received in Router Advertisements.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 address autoconfiguration is disabled on all interfaces.
+
+		Only the IPv6 loopback address (::1) and link-local addresses
+		will be added to interfaces.
+
+	1
+		IPv6 address autoconfiguration is enabled on all interfaces.
+
+		This is the default value.
+
+disable_ipv6
+
+	Specifies whether to disable IPv6 on all interfaces.
+	This might be used when no IPv6 addresses are desired.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 is enabled on all interfaces.
+
+		This is the default value.
+
+	1
+		IPv6 is disabled on all interfaces.
+
+		No IPv6 addresses will be added to interfaces.
+