From e24328974a88aa8541e94e8bb8dfa2ade1b3c45d Mon Sep 17 00:00:00 2001 From: Donggeun Yoo Date: Wed, 2 Sep 2026 00:21:26 +0900 Subject: iio: proximity: vl53l0x-i2c: claim direct mode for raw reads vl53l0x_read_raw() starts a single-shot ranging measurement and reads back the result. Once the triggered buffer is enabled the sensor runs in continuous mode and its data-ready interrupt is routed to the trigger, so a concurrent in_distance_raw read disturbs the streaming setup and never gets its completion, returning -ETIMEDOUT. The original submission claimed direct mode here, but it was dropped during review because the driver had no buffer support at the time [1]. Continuous (buffered) mode was later added without restoring the claim [2], reintroducing the conflict. Reject direct reads while buffered capture is active by claiming direct mode around the measurement, as the vl53l1x sibling already does. Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support") Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1] Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2] Signed-off-by: Donggeun Yoo Cc: stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- Documentation/networking/ipv6.rst | 78 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 78 insertions(+) create mode 100644 Documentation/networking/ipv6.rst (limited to 'Documentation/networking/ipv6.rst') diff --git a/Documentation/networking/ipv6.rst b/Documentation/networking/ipv6.rst new file mode 100644 index 000000000..ba09c2f2d --- /dev/null +++ b/Documentation/networking/ipv6.rst @@ -0,0 +1,78 @@ +.. SPDX-License-Identifier: GPL-2.0 + +==== +IPv6 +==== + + +Options for the ipv6 module are supplied as parameters at load time. + +Module options may be given as command line arguments to the insmod +or modprobe command, but are usually specified in either +``/etc/modules.d/*.conf`` configuration files, or in a distro-specific +configuration file. + +The available ipv6 module parameters are listed below. If a parameter +is not specified the default value is used. + +The parameters are as follows: + +disable + + Specifies whether to load the IPv6 module, but disable all + its functionality. This might be used when another module + has a dependency on the IPv6 module being loaded, but no + IPv6 addresses or operations are desired. + + The possible values and their effects are: + + 0 + IPv6 is enabled. + + This is the default value. + + 1 + IPv6 is disabled. + + No IPv6 addresses will be added to interfaces, and + it will not be possible to open an IPv6 socket. + + A reboot is required to enable IPv6. + +autoconf + + Specifies whether to enable IPv6 address autoconfiguration + on all interfaces. This might be used when one does not wish + for addresses to be automatically generated from prefixes + received in Router Advertisements. + + The possible values and their effects are: + + 0 + IPv6 address autoconfiguration is disabled on all interfaces. + + Only the IPv6 loopback address (::1) and link-local addresses + will be added to interfaces. + + 1 + IPv6 address autoconfiguration is enabled on all interfaces. + + This is the default value. + +disable_ipv6 + + Specifies whether to disable IPv6 on all interfaces. + This might be used when no IPv6 addresses are desired. + + The possible values and their effects are: + + 0 + IPv6 is enabled on all interfaces. + + This is the default value. + + 1 + IPv6 is disabled on all interfaces. + + No IPv6 addresses will be added to interfaces. + -- cgit v1.3.1