iio: proximity: vl53l0x-i2c: claim direct mode for raw readsgrafted

vl53l0x_read_raw() starts a single-shot ranging measurement and reads
back the result. Once the triggered buffer is enabled the sensor runs in
continuous mode and its data-ready interrupt is routed to the trigger,
so a concurrent in_distance_raw read disturbs the streaming setup and
never gets its completion, returning -ETIMEDOUT.

The original submission claimed direct mode here, but it was dropped
during review because the driver had no buffer support at the time [1].
Continuous (buffered) mode was later added without restoring the
claim [2], reintroducing the conflict.

Reject direct reads while buffered capture is active by claiming direct
mode around the measurement, as the vl53l1x sibling already does.

Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support")
Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1]
Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2]
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

1 files changed, 34 insertions, 0 deletions

diff --git a/Documentation/filesystems/ext4/bigalloc.rst b/Documentation/filesystems/ext4/bigalloc.rst
new file mode 100644
index 000000000..976a180b2
--- /dev/null
+++ b/Documentation/filesystems/ext4/bigalloc.rst
@@ -0,0 +1,34 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Bigalloc
+--------
+
+At the moment, the default size of a block is 4KiB, which is a commonly
+supported page size on most MMU-capable hardware. This is fortunate, as
+ext4 code is not prepared to handle the case where the block size
+exceeds the page size. However, for a filesystem of mostly huge files,
+it is desirable to be able to allocate disk blocks in units of multiple
+blocks to reduce both fragmentation and metadata overhead. The
+bigalloc feature provides exactly this ability.
+
+The bigalloc feature (EXT4_FEATURE_RO_COMPAT_BIGALLOC) changes ext4 to
+use clustered allocation, so that each bit in the ext4 block allocation
+bitmap addresses a power of two number of blocks. For example, if the
+file system is mainly going to be storing large files in the 4-32
+megabyte range, it might make sense to set a cluster size of 1 megabyte.
+This means that each bit in the block allocation bitmap now addresses
+256 4k blocks. This shrinks the total size of the block allocation
+bitmaps for a 2T file system from 64 megabytes to 256 kilobytes. It also
+means that a block group addresses 32 gigabytes instead of 128 megabytes,
+also shrinking the amount of file system overhead for metadata.
+
+The administrator can set a block cluster size at mkfs time (which is
+stored in the s_log_cluster_size field in the superblock); from then
+on, the block bitmaps track clusters, not individual blocks. This means
+that block groups can be several gigabytes in size (instead of just
+128MiB); however, the minimum allocation unit becomes a cluster, not a
+block, even for directories. TaoBao had a patchset to extend the “use
+units of clusters instead of blocks” to the extent tree, though it is
+not clear where those patches went-- they eventually morphed into
+“extent tree v2” but that code has not landed as of May 2015.
+