From e24328974a88aa8541e94e8bb8dfa2ade1b3c45d Mon Sep 17 00:00:00 2001 From: Donggeun Yoo Date: Wed, 2 Sep 2026 00:21:26 +0900 Subject: iio: proximity: vl53l0x-i2c: claim direct mode for raw reads vl53l0x_read_raw() starts a single-shot ranging measurement and reads back the result. Once the triggered buffer is enabled the sensor runs in continuous mode and its data-ready interrupt is routed to the trigger, so a concurrent in_distance_raw read disturbs the streaming setup and never gets its completion, returning -ETIMEDOUT. The original submission claimed direct mode here, but it was dropped during review because the driver had no buffer support at the time [1]. Continuous (buffered) mode was later added without restoring the claim [2], reintroducing the conflict. Reject direct reads while buffered capture is active by claiming direct mode around the measurement, as the vl53l1x sibling already does. Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support") Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1] Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2] Signed-off-by: Donggeun Yoo Cc: stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- Documentation/filesystems/ext4/bigalloc.rst | 34 +++++++++++++++++++++++++++++ 1 file changed, 34 insertions(+) create mode 100644 Documentation/filesystems/ext4/bigalloc.rst (limited to 'Documentation/filesystems/ext4/bigalloc.rst') diff --git a/Documentation/filesystems/ext4/bigalloc.rst b/Documentation/filesystems/ext4/bigalloc.rst new file mode 100644 index 000000000..976a180b2 --- /dev/null +++ b/Documentation/filesystems/ext4/bigalloc.rst @@ -0,0 +1,34 @@ +.. SPDX-License-Identifier: GPL-2.0 + +Bigalloc +-------- + +At the moment, the default size of a block is 4KiB, which is a commonly +supported page size on most MMU-capable hardware. This is fortunate, as +ext4 code is not prepared to handle the case where the block size +exceeds the page size. However, for a filesystem of mostly huge files, +it is desirable to be able to allocate disk blocks in units of multiple +blocks to reduce both fragmentation and metadata overhead. The +bigalloc feature provides exactly this ability. + +The bigalloc feature (EXT4_FEATURE_RO_COMPAT_BIGALLOC) changes ext4 to +use clustered allocation, so that each bit in the ext4 block allocation +bitmap addresses a power of two number of blocks. For example, if the +file system is mainly going to be storing large files in the 4-32 +megabyte range, it might make sense to set a cluster size of 1 megabyte. +This means that each bit in the block allocation bitmap now addresses +256 4k blocks. This shrinks the total size of the block allocation +bitmaps for a 2T file system from 64 megabytes to 256 kilobytes. It also +means that a block group addresses 32 gigabytes instead of 128 megabytes, +also shrinking the amount of file system overhead for metadata. + +The administrator can set a block cluster size at mkfs time (which is +stored in the s_log_cluster_size field in the superblock); from then +on, the block bitmaps track clusters, not individual blocks. This means +that block groups can be several gigabytes in size (instead of just +128MiB); however, the minimum allocation unit becomes a cluster, not a +block, even for directories. TaoBao had a patchset to extend the “use +units of clusters instead of blocks” to the extent tree, though it is +not clear where those patches went-- they eventually morphed into +“extent tree v2” but that code has not landed as of May 2015. + -- cgit v1.3.1