drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validationgrafted

amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and
uses the first encoding that validates. YCbCr 4:4:4 is listed before
RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the
"color format" property is left at AUTO, even though RGB fits the same
link.

That contradicts the documented AUTO behaviour for HDMI in enum
drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when
the bandwidth is not available or the mode is 4:2:0-only), which the
amdgpu implementation of the property also describes. It also leaves
the "Broadcast RGB" property without effect on such sinks, since the
quantization range it selects only applies to RGB output.

Try RGB first. The mask still holds every encoding the sink supports,
so a mode that cannot carry RGB falls back exactly as before.

For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced
through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI
sink that advertised it.

Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation")
Suggested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Assisted-by: Claude Code:claude-fable-5-1
Signed-off-by: Adrian Betschart <adrian.betschart@cinemaone.ch>
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7)

1 files changed, 46 insertions, 0 deletions

diff --git a/Documentation/arch/parisc/debugging.rst b/Documentation/arch/parisc/debugging.rst
new file mode 100644
index 000000000..de1b60402
--- /dev/null
+++ b/Documentation/arch/parisc/debugging.rst
@@ -0,0 +1,46 @@
+=================
+PA-RISC Debugging
+=================
+
+okay, here are some hints for debugging the lower-level parts of
+linux/parisc.
+
+
+1. Absolute addresses
+=====================
+
+A lot of the assembly code currently runs in real mode, which means
+absolute addresses are used instead of virtual addresses as in the
+rest of the kernel.  To translate an absolute address to a virtual
+address you can lookup in System.map, add __PAGE_OFFSET (0x10000000
+currently).
+
+
+2. HPMCs
+========
+
+When real-mode code tries to access non-existent memory, you'll get
+an HPMC instead of a kernel oops.  To debug an HPMC, try to find
+the System Responder/Requestor addresses.  The System Requestor
+address should match (one of the) processor HPAs (high addresses in
+the I/O range); the System Responder address is the address real-mode
+code tried to access.
+
+Typical values for the System Responder address are addresses larger
+than __PAGE_OFFSET (0x10000000) which mean a virtual address didn't
+get translated to a physical address before real-mode code tried to
+access it.
+
+
+3. Q bit fun
+============
+
+Certain, very critical code has to clear the Q bit in the PSW.  What
+happens when the Q bit is cleared is the CPU does not update the
+registers interruption handlers read to find out where the machine
+was interrupted - so if you get an interruption between the instruction
+that clears the Q bit and the RFI that sets it again you don't know
+where exactly it happened.  If you're lucky the IAOQ will point to the
+instruction that cleared the Q bit, if you're not it points anywhere
+at all.  Usually Q bit problems will show themselves in unexplainable
+system hangs or running off the end of physical memory.