drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validationgrafted

amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and
uses the first encoding that validates. YCbCr 4:4:4 is listed before
RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the
"color format" property is left at AUTO, even though RGB fits the same
link.

That contradicts the documented AUTO behaviour for HDMI in enum
drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when
the bandwidth is not available or the mode is 4:2:0-only), which the
amdgpu implementation of the property also describes. It also leaves
the "Broadcast RGB" property without effect on such sinks, since the
quantization range it selects only applies to RGB output.

Try RGB first. The mask still holds every encoding the sink supports,
so a mode that cannot carry RGB falls back exactly as before.

For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced
through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI
sink that advertised it.

Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation")
Suggested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Assisted-by: Claude Code:claude-fable-5-1
Signed-off-by: Adrian Betschart <adrian.betschart@cinemaone.ch>
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7)

4 files changed, 216 insertions, 0 deletions

diff --git a/Documentation/arch/parisc/debugging.rst b/Documentation/arch/parisc/debugging.rst
new file mode 100644
index 000000000..de1b60402
--- /dev/null
+++ b/Documentation/arch/parisc/debugging.rst
@@ -0,0 +1,46 @@
+=================
+PA-RISC Debugging
+=================
+
+okay, here are some hints for debugging the lower-level parts of
+linux/parisc.
+
+
+1. Absolute addresses
+=====================
+
+A lot of the assembly code currently runs in real mode, which means
+absolute addresses are used instead of virtual addresses as in the
+rest of the kernel.  To translate an absolute address to a virtual
+address you can lookup in System.map, add __PAGE_OFFSET (0x10000000
+currently).
+
+
+2. HPMCs
+========
+
+When real-mode code tries to access non-existent memory, you'll get
+an HPMC instead of a kernel oops.  To debug an HPMC, try to find
+the System Responder/Requestor addresses.  The System Requestor
+address should match (one of the) processor HPAs (high addresses in
+the I/O range); the System Responder address is the address real-mode
+code tried to access.
+
+Typical values for the System Responder address are addresses larger
+than __PAGE_OFFSET (0x10000000) which mean a virtual address didn't
+get translated to a physical address before real-mode code tried to
+access it.
+
+
+3. Q bit fun
+============
+
+Certain, very critical code has to clear the Q bit in the PSW.  What
+happens when the Q bit is cleared is the CPU does not update the
+registers interruption handlers read to find out where the machine
+was interrupted - so if you get an interruption between the instruction
+that clears the Q bit and the RFI that sets it again you don't know
+where exactly it happened.  If you're lucky the IAOQ will point to the
+instruction that cleared the Q bit, if you're not it points anywhere
+at all.  Usually Q bit problems will show themselves in unexplainable
+system hangs or running off the end of physical memory.
diff --git a/Documentation/arch/parisc/features.rst b/Documentation/arch/parisc/features.rst
new file mode 100644
index 000000000..b3aa4d243
--- /dev/null
+++ b/Documentation/arch/parisc/features.rst
@@ -0,0 +1,3 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+.. kernel-feat:: features parisc
diff --git a/Documentation/arch/parisc/index.rst b/Documentation/arch/parisc/index.rst
new file mode 100644
index 000000000..15ccc787f
--- /dev/null
+++ b/Documentation/arch/parisc/index.rst
@@ -0,0 +1,13 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+====================
+PA-RISC Architecture
+====================
+
+.. toctree::
+   :maxdepth: 2
+
+   debugging
+   registers
+
+   features
diff --git a/Documentation/arch/parisc/registers.rst b/Documentation/arch/parisc/registers.rst
new file mode 100644
index 000000000..59c8ecf3e
--- /dev/null
+++ b/Documentation/arch/parisc/registers.rst
@@ -0,0 +1,154 @@
+================================
+Register Usage for Linux/PA-RISC
+================================
+
+[ an asterisk is used for planned usage which is currently unimplemented ]
+
+General Registers as specified by ABI
+=====================================
+
+Control Registers
+-----------------
+
+===============================	===============================================
+CR 0 (Recovery Counter)		used for ptrace
+CR 1-CR 7(undefined)		unused
+CR 8 (Protection ID)		per-process value*
+CR 9, 12, 13 (PIDS)		unused
+CR10 (CCR)			lazy FPU saving*
+CR11				as specified by ABI (SAR)
+CR14 (interruption vector)	initialized to fault_vector
+CR15 (EIEM)			initialized to all ones*
+CR16 (Interval Timer)		read for cycle count/write starts Interval Tmr
+CR17-CR22			interruption parameters
+CR19				Interrupt Instruction Register
+CR20				Interrupt Space Register
+CR21				Interrupt Offset Register
+CR22				Interrupt PSW
+CR23 (EIRR)			read for pending interrupts/write clears bits
+CR24 (TR 0)			Kernel Space Page Directory Pointer
+CR25 (TR 1)			User   Space Page Directory Pointer
+CR26 (TR 2)			not used
+CR27 (TR 3)			Thread descriptor pointer
+CR28 (TR 4)			not used
+CR29 (TR 5)			not used
+CR30 (TR 6)			current / 0
+CR31 (TR 7)			Temporary register, used in various places
+===============================	===============================================
+
+Space Registers (kernel mode)
+-----------------------------
+
+===============================	===============================================
+SR0				temporary space register
+SR4-SR7 			set to 0
+SR1				temporary space register
+SR2				kernel should not clobber this
+SR3				used for userspace accesses (current process)
+===============================	===============================================
+
+Space Registers (user mode)
+---------------------------
+
+===============================	===============================================
+SR0				temporary space register
+SR1                             temporary space register
+SR2                             holds space of linux gateway page
+SR3                             holds user address space value while in kernel
+SR4-SR7                         Defines short address space for user/kernel
+===============================	===============================================
+
+
+Processor Status Word
+---------------------
+
+===============================	===============================================
+W (64-bit addresses)		0
+E (Little-endian)		0
+S (Secure Interval Timer)	0
+T (Taken Branch Trap)		0
+H (Higher-privilege trap)	0
+L (Lower-privilege trap)	0
+N (Nullify next instruction)	used by C code
+X (Data memory break disable)	0
+B (Taken Branch)		used by C code
+C (code address translation)	1, 0 while executing real-mode code
+V (divide step correction)	used by C code
+M (HPMC mask)			0, 1 while executing HPMC handler*
+C/B (carry/borrow bits)		used by C code
+O (ordered references)		1*
+F (performance monitor)		0
+R (Recovery Counter trap)	0
+Q (collect interruption state)	1 (0 in code directly preceding an rfi)
+P (Protection Identifiers)	1*
+D (Data address translation)	1, 0 while executing real-mode code
+I (external interrupt mask)	used by cli()/sti() macros
+===============================	===============================================
+
+"Invisible" Registers
+---------------------
+
+===============================	===============================================
+PSW default W value		0
+PSW default E value		0
+Shadow Registers		used by interruption handler code
+TOC enable bit			1
+===============================	===============================================
+
+-------------------------------------------------------------------------
+
+The PA-RISC architecture defines 7 registers as "shadow registers".
+Those are used in RETURN FROM INTERRUPTION AND RESTORE instruction to reduce
+the state save and restore time by eliminating the need for general register
+(GR) saves and restores in interruption handlers.
+Shadow registers are the GRs 1, 8, 9, 16, 17, 24, and 25.
+
+-------------------------------------------------------------------------
+
+Register usage notes, originally from John Marvin, with some additional
+notes from Randolph Chung.
+
+For the general registers:
+
+r1,r2,r19-r26,r28,r29 & r31 can be used without saving them first. And of
+course, you need to save them if you care about them, before calling
+another procedure. Some of the above registers do have special meanings
+that you should be aware of:
+
+    r1:
+	The addil instruction is hardwired to place its result in r1,
+	so if you use that instruction be aware of that.
+
+    r2:
+	This is the return pointer. In general you don't want to
+	use this, since you need the pointer to get back to your
+	caller. However, it is grouped with this set of registers
+	since the caller can't rely on the value being the same
+	when you return, i.e. you can copy r2 to another register
+	and return through that register after trashing r2, and
+	that should not cause a problem for the calling routine.
+
+    r19-r22:
+	these are generally regarded as temporary registers.
+	Note that in 64 bit they are arg7-arg4.
+
+    r23-r26:
+	these are arg3-arg0, i.e. you can use them if you
+	don't care about the values that were passed in anymore.
+
+    r28,r29:
+	are ret0 and ret1. They are what you pass return values
+	in. r28 is the primary return. When returning small structures
+	r29 may also be used to pass data back to the caller.
+
+    r30:
+	stack pointer
+
+    r31:
+	the ble instruction puts the return pointer in here.
+
+
+    r3-r18,r27,r30 need to be saved and restored. r3-r18 are just
+    general purpose registers. r27 is the data pointer, and is
+    used to make references to global variables easier. r30 is
+    the stack pointer.