diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media')
275 files changed, 36264 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/media/allegro,al5e.yaml b/Documentation/devicetree/bindings/media/allegro,al5e.yaml new file mode 100644 index 000000000..2899d26d6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/allegro,al5e.yaml @@ -0,0 +1,105 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/allegro,al5e.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allegro DVT Video IP Codecs + +maintainers: + - Michael Tretter <m.tretter@pengutronix.de> + +description: |- + Allegro DVT video IP codecs present in the Xilinx ZynqMP SoC. The IP core may + either be a H.264/H.265 encoder or H.264/H.265 decoder ip core. + + Each actual codec engine is controlled by a microcontroller (MCU). Host + software uses a provided mailbox interface to communicate with the MCU. The + MCUs share an interrupt. + +properties: + compatible: + oneOf: + - items: + - const: allegro,al5e-1.1 + - const: allegro,al5e + - items: + - const: allegro,al5d-1.1 + - const: allegro,al5d + + reg: + items: + - description: The registers + - description: The SRAM + + reg-names: + items: + - const: regs + - const: sram + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Core clock + - description: MCU clock + - description: Core AXI master port clock + - description: MCU AXI master port clock + - description: AXI4-Lite slave port clock + + clock-names: + items: + - const: core_clk + - const: mcu_clk + - const: m_axi_core_aclk + - const: m_axi_mcu_aclk + - const: s_axi_lite_aclk + +required: + - compatible + - reg + - reg-names + - interrupts + - clocks + - clock-names + +additionalProperties: False + +examples: + - | + fpga { + #address-cells = <2>; + #size-cells = <2>; + + al5e: video-codec@a0009000 { + compatible = "allegro,al5e-1.1", "allegro,al5e"; + reg = <0 0xa0009000 0 0x1000>, + <0 0xa0000000 0 0x8000>; + reg-names = "regs", "sram"; + interrupts = <0 96 4>; + clocks = <&xlnx_vcu 0>, <&xlnx_vcu 1>, + <&clkc 71>, <&clkc 71>, <&clkc 71>; + clock-names = "core_clk", "mcu_clk", "m_axi_core_aclk", + "m_axi_mcu_aclk", "s_axi_lite_aclk"; + }; + }; + - | + fpga { + #address-cells = <2>; + #size-cells = <2>; + + al5d: video-codec@a0029000 { + compatible = "allegro,al5d-1.1", "allegro,al5d"; + reg = <0 0xa0029000 0 0x1000>, + <0 0xa0020000 0 0x8000>; + reg-names = "regs", "sram"; + interrupts = <0 96 4>; + clocks = <&xlnx_vcu 2>, <&xlnx_vcu 3>, + <&clkc 71>, <&clkc 71>, <&clkc 71>; + clock-names = "core_clk", "mcu_clk", "m_axi_core_aclk", + "m_axi_mcu_aclk", "s_axi_lite_aclk"; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-csi.yaml b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-csi.yaml new file mode 100644 index 000000000..617264ce4 --- /dev/null +++ b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-csi.yaml @@ -0,0 +1,129 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/allwinner,sun4i-a10-csi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 CMOS Sensor Interface (CSI) + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +description: |- + The Allwinner A10 and later has a CMOS Sensor Interface to retrieve + frames from a parallel or BT656 sensor. + +properties: + compatible: + oneOf: + - const: allwinner,sun4i-a10-csi1 + - const: allwinner,sun7i-a20-csi0 + - items: + - const: allwinner,sun7i-a20-csi1 + - const: allwinner,sun4i-a10-csi1 + - items: + - const: allwinner,sun8i-r40-csi0 + - const: allwinner,sun7i-a20-csi0 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + oneOf: + - items: + - description: The CSI interface clock + - description: The CSI DRAM clock + + - items: + - description: The CSI interface clock + - description: The CSI ISP clock + - description: The CSI DRAM clock + + clock-names: + oneOf: + - items: + - const: bus + - const: ram + + - items: + - const: bus + - const: isp + - const: ram + + resets: + maxItems: 1 + + # FIXME: This should be made required eventually once every SoC will + # have the MBUS declared. + interconnects: + maxItems: 1 + + # FIXME: This should be made required eventually once every SoC will + # have the MBUS declared. + interconnect-names: + const: dma-mem + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-width: + enum: [8, 16] + + data-active: true + hsync-active: true + pclk-sample: true + vsync-active: true + + required: + - bus-width + - data-active + - hsync-active + - pclk-sample + - vsync-active + +required: + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/sun7i-a20-ccu.h> + #include <dt-bindings/reset/sun4i-a10-ccu.h> + + csi0: csi@1c09000 { + compatible = "allwinner,sun7i-a20-csi0"; + reg = <0x01c09000 0x1000>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_AHB_CSI0>, <&ccu CLK_CSI_SCLK>, <&ccu CLK_DRAM_CSI0>; + clock-names = "bus", "isp", "ram"; + resets = <&ccu RST_CSI0>; + + port { + csi_from_ov5640: endpoint { + remote-endpoint = <&ov5640_to_csi>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml new file mode 100644 index 000000000..42dfe22ad --- /dev/null +++ b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/allwinner,sun4i-a10-ir.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 Infrared Controller + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +allOf: + - $ref: rc.yaml# + +properties: + compatible: + oneOf: + - const: allwinner,sun4i-a10-ir + - const: allwinner,sun5i-a13-ir + - const: allwinner,sun6i-a31-ir + - items: + - enum: + - allwinner,suniv-f1c100s-ir + - allwinner,sun8i-a83t-ir + - allwinner,sun8i-r40-ir + - allwinner,sun50i-a64-ir + - allwinner,sun50i-h6-ir + - allwinner,sun50i-h616-ir + - const: allwinner,sun6i-a31-ir + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: apb + - const: ir + + resets: + maxItems: 1 + + clock-frequency: + default: 8000000 + description: + IR Receiver clock frequency, in Hertz. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + ir0: ir@1c21800 { + compatible = "allwinner,sun4i-a10-ir"; + clocks = <&apb0_gates 6>, <&ir0_clk>; + clock-names = "apb", "ir"; + clock-frequency = <3000000>; + resets = <&apb0_rst 1>; + interrupts = <0 5 1>; + reg = <0x01C21800 0x40>; + linux,rc-map-name = "rc-rc6-mce"; + }; + +... diff --git a/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-video-engine.yaml b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-video-engine.yaml new file mode 100644 index 000000000..01f2afa02 --- /dev/null +++ b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-video-engine.yaml @@ -0,0 +1,104 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/allwinner,sun4i-a10-video-engine.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 Video Engine + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + compatible: + enum: + - allwinner,sun4i-a10-video-engine + - allwinner,sun5i-a13-video-engine + - allwinner,sun7i-a20-video-engine + - allwinner,sun8i-a33-video-engine + - allwinner,sun8i-h3-video-engine + - allwinner,sun8i-v3s-video-engine + - allwinner,sun8i-r40-video-engine + - allwinner,sun20i-d1-video-engine + - allwinner,sun50i-a64-video-engine + - allwinner,sun50i-h5-video-engine + - allwinner,sun50i-h6-video-engine + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + - description: RAM Clock + + clock-names: + items: + - const: ahb + - const: mod + - const: ram + + resets: + maxItems: 1 + + allwinner,sram: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to SRAM + - description: register value for device + description: Phandle to the device SRAM + + iommus: + maxItems: 1 + + memory-region: + maxItems: 1 + description: + CMA pool to use for buffers allocation instead of the default + CMA pool. + + # FIXME: This should be made required eventually once every SoC will + # have the MBUS declared. + interconnects: + maxItems: 1 + + # FIXME: This should be made required eventually once every SoC will + # have the MBUS declared. + interconnect-names: + const: dma-mem + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + - allwinner,sram + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/sun7i-a20-ccu.h> + #include <dt-bindings/reset/sun4i-a10-ccu.h> + + video-codec@1c0e000 { + compatible = "allwinner,sun7i-a20-video-engine"; + reg = <0x01c0e000 0x1000>; + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_AHB_VE>, <&ccu CLK_VE>, + <&ccu CLK_DRAM_VE>; + clock-names = "ahb", "mod", "ram"; + resets = <&ccu RST_VE>; + allwinner,sram = <&ve_sram 1>; + }; + +... diff --git a/Documentation/devicetree/bindings/media/allwinner,sun50i-h6-vpu-g2.yaml b/Documentation/devicetree/bindings/media/allwinner,sun50i-h6-vpu-g2.yaml new file mode 100644 index 000000000..8ba5177ac --- /dev/null +++ b/Documentation/devicetree/bindings/media/allwinner,sun50i-h6-vpu-g2.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/allwinner,sun50i-h6-vpu-g2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Hantro G2 VPU codec implemented on Allwinner H6 SoC + +maintainers: + - Jernej Skrabec <jernej.skrabec@gmail.com> + +description: + Hantro G2 video decode accelerator present on Allwinner H6 SoC. + +properties: + compatible: + const: allwinner,sun50i-h6-vpu-g2 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: bus + - const: mod + + resets: + maxItems: 1 + + iommus: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + - iommus + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/sun50i-h6-ccu.h> + #include <dt-bindings/reset/sun50i-h6-ccu.h> + + video-codec-g2@1c00000 { + compatible = "allwinner,sun50i-h6-vpu-g2"; + reg = <0x01c00000 0x1000>; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_VP9>, <&ccu CLK_VP9>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_VP9>; + iommus = <&iommu 5>; + }; + +... diff --git a/Documentation/devicetree/bindings/media/allwinner,sun6i-a31-csi.yaml b/Documentation/devicetree/bindings/media/allwinner,sun6i-a31-csi.yaml new file mode 100644 index 000000000..978ef2dc0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/allwinner,sun6i-a31-csi.yaml @@ -0,0 +1,149 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/allwinner,sun6i-a31-csi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 CMOS Sensor Interface (CSI) + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + compatible: + enum: + - allwinner,sun6i-a31-csi + - allwinner,sun8i-a83t-csi + - allwinner,sun8i-h3-csi + - allwinner,sun8i-v3s-csi + - allwinner,sun50i-a64-csi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + - description: DRAM Clock + + clock-names: + items: + - const: bus + - const: mod + - const: ram + + resets: + maxItems: 1 + + interconnects: + maxItems: 1 + + interconnect-names: + const: dma-mem + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + description: Parallel input port, connect to a parallel sensor + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-width: + enum: [ 8, 10, 12, 16 ] + + pclk-sample: true + hsync-active: true + vsync-active: true + + required: + - bus-width + + unevaluatedProperties: false + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: "#/properties/port" + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: MIPI CSI-2 bridge input port + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: Internal output port to the ISP + + anyOf: + - required: + - port@0 + - required: + - port@1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + +oneOf: + - required: + - ports + - required: + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/sun8i-v3s-ccu.h> + #include <dt-bindings/reset/sun8i-v3s-ccu.h> + + csi1: csi@1cb4000 { + compatible = "allwinner,sun8i-v3s-csi"; + reg = <0x01cb4000 0x1000>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI_SCLK>, + <&ccu CLK_DRAM_CSI>; + clock-names = "bus", + "mod", + "ram"; + resets = <&ccu RST_BUS_CSI>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + /* Parallel bus endpoint */ + csi1_ep: endpoint { + remote-endpoint = <&adv7611_ep>; + bus-width = <16>; + + /* + * If hsync-active/vsync-active are missing, + * embedded BT.656 sync is used. + */ + hsync-active = <0>; /* Active low */ + vsync-active = <0>; /* Active low */ + pclk-sample = <1>; /* Rising */ + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/allwinner,sun6i-a31-isp.yaml b/Documentation/devicetree/bindings/media/allwinner,sun6i-a31-isp.yaml new file mode 100644 index 000000000..c0d7accc7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/allwinner,sun6i-a31-isp.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/allwinner,sun6i-a31-isp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 Image Signal Processor Driver (ISP) + +maintainers: + - Paul Kocialkowski <paul.kocialkowski@bootlin.com> + +properties: + compatible: + enum: + - allwinner,sun6i-a31-isp + - allwinner,sun8i-v3s-isp + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + - description: DRAM Clock + + clock-names: + items: + - const: bus + - const: mod + - const: ram + + resets: + maxItems: 1 + + interconnects: + maxItems: 1 + + interconnect-names: + const: dma-mem + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: CSI0 input port + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: CSI1 input port + + if: + properties: + compatible: + contains: + enum: + - allwinner,sun8i-v3s-isp + then: + required: + - port@0 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/sun8i-v3s-ccu.h> + #include <dt-bindings/reset/sun8i-v3s-ccu.h> + + isp: isp@1cb8000 { + compatible = "allwinner,sun8i-v3s-isp"; + reg = <0x01cb8000 0x1000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI_SCLK>, + <&ccu CLK_DRAM_CSI>; + clock-names = "bus", "mod", "ram"; + resets = <&ccu RST_BUS_CSI>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + isp_in_csi0: endpoint { + remote-endpoint = <&csi0_out_isp>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/allwinner,sun6i-a31-mipi-csi2.yaml b/Documentation/devicetree/bindings/media/allwinner,sun6i-a31-mipi-csi2.yaml new file mode 100644 index 000000000..627b28e94 --- /dev/null +++ b/Documentation/devicetree/bindings/media/allwinner,sun6i-a31-mipi-csi2.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/allwinner,sun6i-a31-mipi-csi2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 MIPI CSI-2 + +maintainers: + - Paul Kocialkowski <paul.kocialkowski@bootlin.com> + +properties: + compatible: + oneOf: + - const: allwinner,sun6i-a31-mipi-csi2 + - items: + - const: allwinner,sun8i-v3s-mipi-csi2 + - const: allwinner,sun6i-a31-mipi-csi2 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: bus + - const: mod + + phys: + maxItems: 1 + description: MIPI D-PHY + + phy-names: + items: + - const: dphy + + resets: + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + description: Input port, connect to a MIPI CSI-2 sensor + + properties: + reg: + const: 0 + + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + + unevaluatedProperties: false + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Output port, connect to a CSI controller + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - phys + - phy-names + - resets + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/sun8i-v3s-ccu.h> + #include <dt-bindings/reset/sun8i-v3s-ccu.h> + + mipi_csi2: csi@1cb1000 { + compatible = "allwinner,sun8i-v3s-mipi-csi2", + "allwinner,sun6i-a31-mipi-csi2"; + reg = <0x01cb1000 0x1000>; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI_SCLK>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_CSI>; + + phys = <&dphy>; + phy-names = "dphy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mipi_csi2_in: port@0 { + reg = <0>; + + mipi_csi2_in_ov5648: endpoint { + data-lanes = <1 2 3 4>; + + remote-endpoint = <&ov5648_out_mipi_csi2>; + }; + }; + + mipi_csi2_out: port@1 { + reg = <1>; + + mipi_csi2_out_csi0: endpoint { + remote-endpoint = <&csi0_in_mipi_csi2>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/allwinner,sun8i-a83t-de2-rotate.yaml b/Documentation/devicetree/bindings/media/allwinner,sun8i-a83t-de2-rotate.yaml new file mode 100644 index 000000000..c2f292dd0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/allwinner,sun8i-a83t-de2-rotate.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/allwinner,sun8i-a83t-de2-rotate.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A83T DE2 Rotate + +maintainers: + - Jernej Skrabec <jernej.skrabec@siol.net> + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +description: |- + The Allwinner A83T and A64 have a rotation core used for + rotating and flipping images. + +properties: + compatible: + oneOf: + - const: allwinner,sun8i-a83t-de2-rotate + - items: + - const: allwinner,sun50i-a64-de2-rotate + - const: allwinner,sun8i-a83t-de2-rotate + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Rotate interface clock + - description: Rotate module clock + + clock-names: + items: + - const: bus + - const: mod + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/sun8i-de2.h> + #include <dt-bindings/reset/sun8i-de2.h> + + rotate: rotate@1020000 { + compatible = "allwinner,sun8i-a83t-de2-rotate"; + reg = <0x1020000 0x10000>; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&display_clocks CLK_BUS_ROT>, + <&display_clocks CLK_ROT>; + clock-names = "bus", + "mod"; + resets = <&display_clocks RST_ROT>; + }; + +... diff --git a/Documentation/devicetree/bindings/media/allwinner,sun8i-a83t-mipi-csi2.yaml b/Documentation/devicetree/bindings/media/allwinner,sun8i-a83t-mipi-csi2.yaml new file mode 100644 index 000000000..3cac68a87 --- /dev/null +++ b/Documentation/devicetree/bindings/media/allwinner,sun8i-a83t-mipi-csi2.yaml @@ -0,0 +1,125 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/allwinner,sun8i-a83t-mipi-csi2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A83T MIPI CSI-2 + +maintainers: + - Paul Kocialkowski <paul.kocialkowski@bootlin.com> + +properties: + compatible: + const: allwinner,sun8i-a83t-mipi-csi2 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + - description: MIPI-specific Clock + - description: Misc CSI Clock + + clock-names: + items: + - const: bus + - const: mod + - const: mipi + - const: misc + + resets: + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + description: Input port, connect to a MIPI CSI-2 sensor + + properties: + reg: + const: 0 + + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + + unevaluatedProperties: false + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Output port, connect to a CSI controller + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/sun8i-a83t-ccu.h> + #include <dt-bindings/reset/sun8i-a83t-ccu.h> + + mipi_csi2: csi@1cb1000 { + compatible = "allwinner,sun8i-a83t-mipi-csi2"; + reg = <0x01cb1000 0x1000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI_SCLK>, + <&ccu CLK_MIPI_CSI>, + <&ccu CLK_CSI_MISC>; + clock-names = "bus", "mod", "mipi", "misc"; + resets = <&ccu RST_BUS_CSI>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mipi_csi2_in: port@0 { + reg = <0>; + + mipi_csi2_in_ov8865: endpoint { + data-lanes = <1 2 3 4>; + + remote-endpoint = <&ov8865_out_mipi_csi2>; + }; + }; + + mipi_csi2_out: port@1 { + reg = <1>; + + mipi_csi2_out_csi: endpoint { + remote-endpoint = <&csi_in_mipi_csi2>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/allwinner,sun8i-h3-deinterlace.yaml b/Documentation/devicetree/bindings/media/allwinner,sun8i-h3-deinterlace.yaml new file mode 100644 index 000000000..3ccd52164 --- /dev/null +++ b/Documentation/devicetree/bindings/media/allwinner,sun8i-h3-deinterlace.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/allwinner,sun8i-h3-deinterlace.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner H3 Deinterlace + +maintainers: + - Jernej Skrabec <jernej.skrabec@siol.net> + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +description: |- + The Allwinner H3 and later has a deinterlace core used for + deinterlacing interlaced video content. + +properties: + compatible: + oneOf: + - const: allwinner,sun8i-h3-deinterlace + - items: + - const: allwinner,sun8i-r40-deinterlace + - const: allwinner,sun8i-h3-deinterlace + - items: + - const: allwinner,sun50i-a64-deinterlace + - const: allwinner,sun8i-h3-deinterlace + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Deinterlace interface clock + - description: Deinterlace module clock + - description: Deinterlace DRAM clock + + clock-names: + items: + - const: bus + - const: mod + - const: ram + + resets: + maxItems: 1 + + interconnects: + maxItems: 1 + + interconnect-names: + const: dma-mem + +required: + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/sun8i-h3-ccu.h> + #include <dt-bindings/reset/sun8i-h3-ccu.h> + + deinterlace: deinterlace@1400000 { + compatible = "allwinner,sun8i-h3-deinterlace"; + reg = <0x01400000 0x20000>; + clocks = <&ccu CLK_BUS_DEINTERLACE>, + <&ccu CLK_DEINTERLACE>, + <&ccu CLK_DRAM_DEINTERLACE>; + clock-names = "bus", "mod", "ram"; + resets = <&ccu RST_BUS_DEINTERLACE>; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; + interconnects = <&mbus 9>; + interconnect-names = "dma-mem"; + }; + +... diff --git a/Documentation/devicetree/bindings/media/amlogic,axg-ge2d.yaml b/Documentation/devicetree/bindings/media/amlogic,axg-ge2d.yaml new file mode 100644 index 000000000..f23fa6d06 --- /dev/null +++ b/Documentation/devicetree/bindings/media/amlogic,axg-ge2d.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2020 BayLibre, SAS +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/amlogic,axg-ge2d.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic GE2D Acceleration Unit + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +properties: + compatible: + enum: + - amlogic,axg-ge2d + + interrupts: + minItems: 1 + + reg: + minItems: 1 + + resets: + maxItems: 1 + + clocks: + minItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - resets + +additionalProperties: false + +examples: + - | + ge2d: ge2d@ff940000 { + compatible = "amlogic,axg-ge2d"; + reg = <0xff940000 0x10000>; + interrupts = <150>; + clocks = <&clk_ge2d>; + resets = <&reset_ge2d>; + }; diff --git a/Documentation/devicetree/bindings/media/amlogic,c3-isp.yaml b/Documentation/devicetree/bindings/media/amlogic,c3-isp.yaml new file mode 100644 index 000000000..123bf462f --- /dev/null +++ b/Documentation/devicetree/bindings/media/amlogic,c3-isp.yaml @@ -0,0 +1,88 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/amlogic,c3-isp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic C3 Image Signal Processing Unit + +maintainers: + - Keke Li <keke.li@amlogic.com> + +description: + Amlogic ISP is the RAW image processing module + and supports three channels image output. + +properties: + compatible: + enum: + - amlogic,c3-isp + + reg: + maxItems: 1 + + reg-names: + items: + - const: isp + + power-domains: + maxItems: 1 + + clocks: + maxItems: 2 + + clock-names: + items: + - const: vapb + - const: isp0 + + interrupts: + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/properties/port + description: input port node. + +required: + - compatible + - reg + - reg-names + - power-domains + - clocks + - clock-names + - interrupts + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/amlogic,c3-peripherals-clkc.h> + #include <dt-bindings/power/amlogic,c3-pwrc.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + isp: isp@ff000000 { + compatible = "amlogic,c3-isp"; + reg = <0x0 0xff000000 0x0 0xf000>; + reg-names = "isp"; + power-domains = <&pwrc PWRC_C3_ISP_TOP_ID>; + clocks = <&clkc_periphs CLKID_VAPB>, + <&clkc_periphs CLKID_ISP0>; + clock-names = "vapb", "isp0"; + assigned-clocks = <&clkc_periphs CLKID_VAPB>, + <&clkc_periphs CLKID_ISP0>; + assigned-clock-rates = <0>, <400000000>; + interrupts = <GIC_SPI 145 IRQ_TYPE_EDGE_RISING>; + + port { + c3_isp_in: endpoint { + remote-endpoint = <&c3_adap_out>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/amlogic,c3-mipi-adapter.yaml b/Documentation/devicetree/bindings/media/amlogic,c3-mipi-adapter.yaml new file mode 100644 index 000000000..ba43bc670 --- /dev/null +++ b/Documentation/devicetree/bindings/media/amlogic,c3-mipi-adapter.yaml @@ -0,0 +1,111 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/amlogic,c3-mipi-adapter.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic C3 MIPI adapter receiver + +maintainers: + - Keke Li <keke.li@amlogic.com> + +description: + MIPI adapter is used to convert the MIPI CSI-2 data + into an ISP supported data format. + +properties: + compatible: + enum: + - amlogic,c3-mipi-adapter + + reg: + maxItems: 3 + + reg-names: + items: + - const: top + - const: fd + - const: rd + + power-domains: + maxItems: 1 + + clocks: + maxItems: 2 + + clock-names: + items: + - const: vapb + - const: isp0 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: input port node. + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: output port node. + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - reg-names + - power-domains + - clocks + - clock-names + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/amlogic,c3-peripherals-clkc.h> + #include <dt-bindings/power/amlogic,c3-pwrc.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + adap: adap@ff010000 { + compatible = "amlogic,c3-mipi-adapter"; + reg = <0x0 0xff010000 0x0 0x100>, + <0x0 0xff01b000 0x0 0x100>, + <0x0 0xff01d000 0x0 0x200>; + reg-names = "top", "fd", "rd"; + power-domains = <&pwrc PWRC_C3_ISP_TOP_ID>; + clocks = <&clkc_periphs CLKID_VAPB>, + <&clkc_periphs CLKID_ISP0>; + clock-names = "vapb", "isp0"; + assigned-clocks = <&clkc_periphs CLKID_VAPB>, + <&clkc_periphs CLKID_ISP0>; + assigned-clock-rates = <0>, <400000000>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + c3_adap_in: endpoint { + remote-endpoint = <&c3_mipi_csi_out>; + }; + }; + + port@1 { + reg = <1>; + c3_adap_out: endpoint { + remote-endpoint = <&c3_isp_in>; + }; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/amlogic,c3-mipi-csi2.yaml b/Documentation/devicetree/bindings/media/amlogic,c3-mipi-csi2.yaml new file mode 100644 index 000000000..b0129beab --- /dev/null +++ b/Documentation/devicetree/bindings/media/amlogic,c3-mipi-csi2.yaml @@ -0,0 +1,127 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/amlogic,c3-mipi-csi2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic C3 MIPI CSI-2 receiver + +maintainers: + - Keke Li <keke.li@amlogic.com> + +description: + MIPI CSI-2 receiver contains CSI-2 RX PHY and host controller. + It receives the MIPI data from the image sensor and sends MIPI data + to MIPI adapter. + +properties: + compatible: + enum: + - amlogic,c3-mipi-csi2 + + reg: + maxItems: 3 + + reg-names: + items: + - const: aphy + - const: dphy + - const: host + + power-domains: + maxItems: 1 + + clocks: + maxItems: 2 + + clock-names: + items: + - const: vapb + - const: phy0 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: input port node, connected to sensor. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: output port node + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - reg-names + - power-domains + - clocks + - clock-names + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/amlogic,c3-peripherals-clkc.h> + #include <dt-bindings/power/amlogic,c3-pwrc.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + csi: csi@ff018000 { + compatible = "amlogic,c3-mipi-csi2"; + reg = <0x0 0xff018000 0x0 0x400>, + <0x0 0xff019000 0x0 0x300>, + <0x0 0xff01a000 0x0 0x100>; + reg-names = "aphy", "dphy", "host"; + power-domains = <&pwrc PWRC_C3_MIPI_ISP_WRAP_ID>; + clocks = <&clkc_periphs CLKID_VAPB>, + <&clkc_periphs CLKID_CSI_PHY0>; + clock-names = "vapb", "phy0"; + assigned-clocks = <&clkc_periphs CLKID_VAPB>, + <&clkc_periphs CLKID_CSI_PHY0>; + assigned-clock-rates = <0>, <200000000>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + c3_mipi_csi_in: endpoint { + remote-endpoint = <&imx290_out>; + data-lanes = <1 2 3 4>; + }; + }; + + port@1 { + reg = <1>; + c3_mipi_csi_out: endpoint { + remote-endpoint = <&c3_adap_in>; + }; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/amlogic,gx-vdec.yaml b/Documentation/devicetree/bindings/media/amlogic,gx-vdec.yaml new file mode 100644 index 000000000..47dce75ae --- /dev/null +++ b/Documentation/devicetree/bindings/media/amlogic,gx-vdec.yaml @@ -0,0 +1,141 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/amlogic,gx-vdec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Video Decoder + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + - Maxime Jourdan <mjourdan@baylibre.com> + +description: | + The video decoding IP lies within the DOS memory region, + except for the hardware bitstream parser that makes use of an undocumented + region. + + It makes use of the following blocks: + - ESPARSER is a bitstream parser that outputs to a VIFIFO. Further VDEC blocks + then feed from this VIFIFO. + - VDEC_1 can decode MPEG-1, MPEG-2, MPEG-4 part 2, MJPEG, H.263, H.264, VC-1. + - VDEC_HEVC can decode HEVC and VP9. + + Both VDEC_1 and VDEC_HEVC share the "vdec" IRQ and as such cannot run + concurrently. + +properties: + compatible: + oneOf: + - items: + - enum: + - amlogic,gxbb-vdec # GXBB (S905) + - amlogic,gxl-vdec # GXL (S905D, S905W, S905X, S905Y) + - amlogic,gxlx-vdec # GXLX (S905L) + - amlogic,gxm-vdec # GXM (S912) + - const: amlogic,gx-vdec + - enum: + - amlogic,g12a-vdec # G12A (S905X2, S905D2) + - amlogic,sm1-vdec # SM1 (S905X3, S905D3) + + interrupts: + minItems: 2 + + interrupt-names: + items: + - const: vdec + - const: esparser + + reg: + minItems: 2 + + reg-names: + items: + - const: dos + - const: esparser + + resets: + maxItems: 1 + + reset-names: + items: + - const: esparser + + clocks: + minItems: 4 + maxItems: 5 + + clock-names: + minItems: 4 + items: + - const: dos_parser + - const: dos + - const: vdec_1 + - const: vdec_hevc + - const: vdec_hevcf + + amlogic,ao-sysctrl: + description: should point to the AOBUS sysctrl node + $ref: /schemas/types.yaml#/definitions/phandle + + amlogic,canvas: + description: should point to a canvas provider node + $ref: /schemas/types.yaml#/definitions/phandle + +allOf: + - if: + properties: + compatible: + contains: + enum: + - amlogic,gx-vdec + + then: + properties: + clock-names: + maxItems: 4 + + - if: + properties: + compatible: + contains: + enum: + - amlogic,g12a-vdec + - amlogic,sm1-vdec + + then: + properties: + clock-names: + minItems: 5 + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-names + - clocks + - clock-names + - resets + - reset-names + - amlogic,ao-sysctrl + - amlogic,canvas + +additionalProperties: false + +examples: + - | + vdec: video-decoder@c8820000 { + compatible = "amlogic,gxl-vdec", "amlogic,gx-vdec"; + reg = <0xc8820000 0x10000>, <0xc110a580 0xe4>; + reg-names = "dos", "esparser"; + interrupts = <44>, <32>; + interrupt-names = "vdec", "esparser"; + clocks = <&clk_dos_parser> ,<&clk_dos>, <&clk_vdec_1>, <&clk_vdec_hevc>; + clock-names = "dos_parser", "dos", "vdec_1", "vdec_hevc"; + resets = <&reset_parser>; + reset-names = "esparser"; + amlogic,ao-sysctrl = <&sysctrl_AO>; + amlogic,canvas = <&canvas>; + }; diff --git a/Documentation/devicetree/bindings/media/amlogic,meson-ir-tx.yaml b/Documentation/devicetree/bindings/media/amlogic,meson-ir-tx.yaml new file mode 100644 index 000000000..6da8a6ade --- /dev/null +++ b/Documentation/devicetree/bindings/media/amlogic,meson-ir-tx.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/amlogic,meson-ir-tx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Meson IR transmitter + +maintainers: + - Viktor Prutyanov <viktor.prutyanov@phystech.edu> + +description: | + Some Amlogic SoCs such as A311D and T950D4 have IR transmitter + (also called blaster) controller onboard. It is capable of + sending IR signals with arbitrary carrier frequency and duty cycle. + +properties: + compatible: + oneOf: + - const: amlogic,meson-ir-tx + - items: + - const: amlogic,meson-g12a-ir-tx + - const: amlogic,meson-ir-tx + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 2 + + clock-names: + items: + - const: sysclk + - const: xtal + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/g12a-clkc.h> + + ir@ff80014c { + compatible = "amlogic,meson-g12a-ir-tx", "amlogic,meson-ir-tx"; + reg = <0xff80014c 0x10>; + interrupts = <0 198 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc CLKID_CLK81>, <&xtal>; + clock-names = "sysclk", "xtal"; + }; diff --git a/Documentation/devicetree/bindings/media/amlogic,meson6-ir.yaml b/Documentation/devicetree/bindings/media/amlogic,meson6-ir.yaml new file mode 100644 index 000000000..0f95fe8dd --- /dev/null +++ b/Documentation/devicetree/bindings/media/amlogic,meson6-ir.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/amlogic,meson6-ir.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Meson IR remote control receiver + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +allOf: + - $ref: rc.yaml# + +properties: + compatible: + oneOf: + - enum: + - amlogic,meson6-ir + - amlogic,meson8b-ir + - amlogic,meson-gxbb-ir + - amlogic,meson-s4-ir + - items: + - const: amlogic,meson-gx-ir + - const: amlogic,meson-gxbb-ir + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + ir-receiver@c8100480 { + compatible = "amlogic,meson6-ir"; + reg = <0xc8100480 0x20>; + interrupts = <GIC_SPI 15 IRQ_TYPE_EDGE_RISING>; + }; diff --git a/Documentation/devicetree/bindings/media/amphion,vpu.yaml b/Documentation/devicetree/bindings/media/amphion,vpu.yaml new file mode 100644 index 000000000..fa18013d7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/amphion,vpu.yaml @@ -0,0 +1,178 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/amphion,vpu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amphion VPU codec IP + +maintainers: + - Ming Qian <ming.qian@nxp.com> + - Shijie Qin <shijie.qin@nxp.com> + +description: |- + The Amphion MXC video encoder(Windsor) and decoder(Malone) accelerators present + on NXP i.MX8Q SoCs. + +properties: + $nodename: + pattern: "^vpu@[0-9a-f]+$" + + compatible: + items: + - enum: + - nxp,imx8qm-vpu + - nxp,imx8qxp-vpu + + reg: + maxItems: 1 + + power-domains: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 1 + + ranges: true + +patternProperties: + "^mailbox@[0-9a-f]+$": + description: + Each vpu encoder or decoder correspond a MU, which used for communication + between driver and firmware. Implement via mailbox on driver. + $ref: /schemas/mailbox/fsl,mu.yaml# + + "^vpu-core@[0-9a-f]+$": + description: + Each core correspond a decoder or encoder, need to configure them + separately. NXP i.MX8QM SoC has one decoder and two encoder, i.MX8QXP SoC + has one decoder and one encoder. + type: object + + properties: + compatible: + items: + - enum: + - nxp,imx8q-vpu-decoder + - nxp,imx8q-vpu-encoder + + reg: + maxItems: 1 + + power-domains: + maxItems: 1 + + mbox-names: + items: + - const: tx0 + - const: tx1 + - const: rx + + mboxes: + description: + List of phandle of 2 MU channels for tx, 1 MU channel for rx. + maxItems: 3 + + memory-region: + description: + Phandle to the reserved memory nodes to be associated with the + remoteproc device. The reserved memory nodes should be carveout nodes, + and should be defined as per the bindings in + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt + items: + - description: region reserved for firmware image sections. + - description: region used for RPC shared memory between firmware and + driver. + + required: + - compatible + - reg + - power-domains + - mbox-names + - mboxes + - memory-region + + additionalProperties: false + +required: + - compatible + - reg + - power-domains + +additionalProperties: false + +examples: + # Device node example for i.MX8QM platform: + - | + #include <dt-bindings/firmware/imx/rsrc.h> + + vpu: vpu@2c000000 { + compatible = "nxp,imx8qm-vpu"; + ranges = <0x2c000000 0x2c000000 0x2000000>; + reg = <0x2c000000 0x1000000>; + #address-cells = <1>; + #size-cells = <1>; + power-domains = <&pd IMX_SC_R_VPU>; + + mu_m0: mailbox@2d000000 { + compatible = "fsl,imx6sx-mu"; + reg = <0x2d000000 0x20000>; + interrupts = <0 472 4>; + #mbox-cells = <2>; + power-domains = <&pd IMX_SC_R_VPU_MU_0>; + }; + + mu1_m0: mailbox@2d020000 { + compatible = "fsl,imx6sx-mu"; + reg = <0x2d020000 0x20000>; + interrupts = <0 473 4>; + #mbox-cells = <2>; + power-domains = <&pd IMX_SC_R_VPU_MU_1>; + }; + + mu2_m0: mailbox@2d040000 { + compatible = "fsl,imx6sx-mu"; + reg = <0x2d040000 0x20000>; + interrupts = <0 474 4>; + #mbox-cells = <2>; + power-domains = <&pd IMX_SC_R_VPU_MU_2>; + }; + + vpu_core0: vpu-core@2d080000 { + compatible = "nxp,imx8q-vpu-decoder"; + reg = <0x2d080000 0x10000>; + power-domains = <&pd IMX_SC_R_VPU_DEC_0>; + mbox-names = "tx0", "tx1", "rx"; + mboxes = <&mu_m0 0 0>, + <&mu_m0 0 1>, + <&mu_m0 1 0>; + memory-region = <&decoder_boot>, <&decoder_rpc>; + }; + + vpu_core1: vpu-core@2d090000 { + compatible = "nxp,imx8q-vpu-encoder"; + reg = <0x2d090000 0x10000>; + power-domains = <&pd IMX_SC_R_VPU_ENC_0>; + mbox-names = "tx0", "tx1", "rx"; + mboxes = <&mu1_m0 0 0>, + <&mu1_m0 0 1>, + <&mu1_m0 1 0>; + memory-region = <&encoder1_boot>, <&encoder1_rpc>; + }; + + vpu_core2: vpu-core@2d0a0000 { + reg = <0x2d0a0000 0x10000>; + compatible = "nxp,imx8q-vpu-encoder"; + power-domains = <&pd IMX_SC_R_VPU_ENC_1>; + mbox-names = "tx0", "tx1", "rx"; + mboxes = <&mu2_m0 0 0>, + <&mu2_m0 0 1>, + <&mu2_m0 1 0>; + memory-region = <&encoder2_boot>, <&encoder2_rpc>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/arm,mali-c55.yaml b/Documentation/devicetree/bindings/media/arm,mali-c55.yaml new file mode 100644 index 000000000..fc4fcd199 --- /dev/null +++ b/Documentation/devicetree/bindings/media/arm,mali-c55.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/arm,mali-c55.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM Mali-C55 Image Signal Processor + +maintainers: + - Daniel Scally <dan.scally@ideasonboard.com> + - Jacopo Mondi <jacopo.mondi@ideasonboard.com> + +properties: + compatible: + const: arm,mali-c55 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: ISP Video Clock + - description: ISP AXI clock + - description: ISP AHB-lite clock + + clock-names: + items: + - const: vclk + - const: aclk + - const: hclk + + resets: + items: + - description: vclk domain reset + - description: aclk domain reset + - description: hclk domain reset + + reset-names: + items: + - const: vresetn + - const: aresetn + - const: hresetn + + port: + $ref: /schemas/graph.yaml#/properties/port + description: Input parallel video bus + + properties: + endpoint: + $ref: /schemas/graph.yaml#/properties/endpoint + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + - reset-names + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + isp@400000 { + compatible = "arm,mali-c55"; + reg = <0x400000 0x200000>; + clocks = <&clk 0>, <&clk 1>, <&clk 2>; + clock-names = "vclk", "aclk", "hclk"; + resets = <&resets 0>, <&resets 1>, <&resets 2>; + reset-names = "vresetn", "aresetn", "hresetn"; + interrupts = <GIC_SPI 861 IRQ_TYPE_EDGE_RISING>; + + port { + isp_in: endpoint { + remote-endpoint = <&csi2_rx_out>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/aspeed,video-engine.yaml b/Documentation/devicetree/bindings/media/aspeed,video-engine.yaml new file mode 100644 index 000000000..682bba207 --- /dev/null +++ b/Documentation/devicetree/bindings/media/aspeed,video-engine.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/aspeed,video-engine.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ASPEED Video Engine + +maintainers: + - Eddie James <eajames@linux.ibm.com> + +description: + The Video Engine (VE) embedded in the ASPEED SOCs can be configured to + capture and compress video data from digital or analog sources. + +properties: + compatible: + enum: + - aspeed,ast2400-video-engine + - aspeed,ast2500-video-engine + - aspeed,ast2600-video-engine + + reg: + maxItems: 1 + + clocks: + maxItems: 2 + + clock-names: + items: + - const: vclk + - const: eclk + + resets: + maxItems: 1 + + interrupts: + maxItems: 1 + + memory-region: + maxItems: 1 + description: | + Phandle to the reserved memory nodes to be associated with the + VE. VE will acquires memory space for 3 purposes: + 1. JPEG header + 2. Compressed result + 3. Temporary transformed image data + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/ast2600-clock.h> + + video@1e700000 { + compatible = "aspeed,ast2600-video-engine"; + reg = <0x1e700000 0x1000>; + clocks = <&syscon ASPEED_CLK_GATE_VCLK>, + <&syscon ASPEED_CLK_GATE_ECLK>; + clock-names = "vclk", "eclk"; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/media/atmel,isc.yaml b/Documentation/devicetree/bindings/media/atmel,isc.yaml new file mode 100644 index 000000000..dc8aba698 --- /dev/null +++ b/Documentation/devicetree/bindings/media/atmel,isc.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: GPL-2.0-only +# Copyright (C) 2016-2021 Microchip Technology, Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/atmel,isc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Atmel Image Sensor Controller (ISC) + +maintainers: + - Eugen Hristev <eugen.hristev@microchip.com> + +description: | + The Image Sensor Controller (ISC) device provides the video input capabilities for the + Atmel/Microchip AT91 SAMA family of devices. + + The ISC has a single parallel input that supports RAW Bayer, RGB or YUV video, + with both external synchronization and BT.656 synchronization for the latter. + +properties: + compatible: + const: atmel,sama5d2-isc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 3 + maxItems: 3 + + clock-names: + items: + - const: hclock + - const: iscck + - const: gck + + '#clock-cells': + const: 0 + + clock-output-names: + const: isc-mck + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + description: + Input port node, single endpoint describing the input pad. + + properties: + endpoint: + $ref: video-interfaces.yaml# + + properties: + remote-endpoint: true + + bus-width: + enum: [8, 9, 10, 11, 12] + default: 12 + + hsync-active: + enum: [0, 1] + default: 1 + + vsync-active: + enum: [0, 1] + default: 1 + + pclk-sample: + enum: [0, 1] + default: 1 + + required: + - remote-endpoint + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - '#clock-cells' + - clock-output-names + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + isc: isc@f0008000 { + compatible = "atmel,sama5d2-isc"; + reg = <0xf0008000 0x4000>; + interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>; + clocks = <&isc_clk>, <&iscck>, <&isc_gclk>; + clock-names = "hclock", "iscck", "gck"; + #clock-cells = <0>; + clock-output-names = "isc-mck"; + + port { + isc_0: endpoint { + remote-endpoint = <&ov7740_0>; + hsync-active = <1>; + vsync-active = <0>; + pclk-sample = <1>; + bus-width = <8>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/atmel-isi.txt b/Documentation/devicetree/bindings/media/atmel-isi.txt new file mode 100644 index 000000000..8924c7545 --- /dev/null +++ b/Documentation/devicetree/bindings/media/atmel-isi.txt @@ -0,0 +1,66 @@ +Atmel Image Sensor Interface (ISI) +---------------------------------- + +Required properties for ISI: +- compatible: must be "atmel,at91sam9g45-isi" or "microchip,sam9x60-isi". +- reg: physical base address and length of the registers set for the device. +- interrupts: should contain IRQ line for the ISI. +- clocks: list of clock specifiers, corresponding to entries in the clock-names + property; please refer to clock-bindings.txt. +- clock-names: required elements: "isi_clk". +- pinctrl-names, pinctrl-0: please refer to pinctrl-bindings.txt. + +ISI supports a single port node with parallel bus. It shall contain one +'port' child node with child 'endpoint' node. Please refer to the bindings +defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + +Endpoint node properties +------------------------ + +- bus-width: <8> or <10> (mandatory) +- hsync-active (default: active high) +- vsync-active (default: active high) +- pclk-sample (default: sample on falling edge) +- remote-endpoint: A phandle to the bus receiver's endpoint node (mandatory). + +Example: + +isi: isi@f0034000 { + compatible = "atmel,at91sam9g45-isi"; + reg = <0xf0034000 0x4000>; + interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_isi_data_0_7>; + clocks = <&isi_clk>; + clock-names = "isi_clk"; + port { + isi_0: endpoint { + remote-endpoint = <&ov2640_0>; + bus-width = <8>; + vsync-active = <1>; + hsync-active = <1>; + }; + }; +}; + +i2c1: i2c@f0018000 { + ov2640: camera@30 { + compatible = "ovti,ov2640"; + reg = <0x30>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; + resetb-gpios = <&pioE 11 GPIO_ACTIVE_LOW>; + pwdn-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>; + clocks = <&pck0>; + clock-names = "xvclk"; + assigned-clocks = <&pck0>; + assigned-clock-rates = <25000000>; + + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + bus-width = <8>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/brcm,bcm2835-unicam.yaml b/Documentation/devicetree/bindings/media/brcm,bcm2835-unicam.yaml new file mode 100644 index 000000000..5fb5d60f0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/brcm,bcm2835-unicam.yaml @@ -0,0 +1,127 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/brcm,bcm2835-unicam.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM283x Camera Interface (Unicam) + +maintainers: + - Raspberry Pi Kernel Maintenance <kernel-list@raspberrypi.com> + +description: |- + The Unicam block on BCM283x SoCs is the receiver for either + CSI-2 or CCP2 data from image sensors or similar devices. + + The main platform using this SoC is the Raspberry Pi family of boards. On + the Pi the VideoCore firmware can also control this hardware block, and + driving it from two different processors will cause issues. To avoid this, + the firmware checks the device tree configuration during boot. If it finds + device tree nodes whose name starts with 'csi' then it will stop the firmware + accessing the block, and it can then safely be used via the device tree + binding. + +properties: + compatible: + const: brcm,bcm2835-unicam + + reg: + items: + - description: Unicam block. + - description: Clock Manager Image (CMI) block. + + reg-names: + items: + - const: unicam + - const: cmi + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Clock to drive the LP state machine of Unicam. + - description: Clock for the VPU (core clock). + + clock-names: + items: + - const: lp + - const: vpu + + power-domains: + items: + - description: Unicam power domain + + brcm,num-data-lanes: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 2, 4 ] + description: | + Number of CSI-2 data lanes supported by this Unicam instance. The number + of data lanes actively used is specified with the data-lanes endpoint + property. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + additionalProperties: false + + properties: + bus-type: + enum: [ 3, 4 ] + + clock-noncontinuous: true + data-lanes: true + remote-endpoint: true + + required: + - bus-type + - data-lanes + - remote-endpoint + + required: + - endpoint + +required: + - compatible + - reg + - reg-names + - interrupts + - clocks + - clock-names + - power-domains + - brcm,num-data-lanes + - port + +additionalProperties: False + +examples: + - | + #include <dt-bindings/clock/bcm2835.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/media/video-interfaces.h> + #include <dt-bindings/power/raspberrypi-power.h> + + csi1: csi@7e801000 { + compatible = "brcm,bcm2835-unicam"; + reg = <0x7e801000 0x800>, + <0x7e802004 0x4>; + reg-names = "unicam", "cmi"; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2835_CLOCK_CAM1>, + <&firmware_clocks 4>; + clock-names = "lp", "vpu"; + power-domains = <&power RPI_POWER_DOMAIN_UNICAM1>; + brcm,num-data-lanes = <2>; + port { + csi1_ep: endpoint { + remote-endpoint = <&imx219_0>; + bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>; + data-lanes = <1 2>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/cdns,csi2rx.yaml b/Documentation/devicetree/bindings/media/cdns,csi2rx.yaml new file mode 100644 index 000000000..6ed9a5621 --- /dev/null +++ b/Documentation/devicetree/bindings/media/cdns,csi2rx.yaml @@ -0,0 +1,210 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/cdns,csi2rx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cadence MIPI-CSI2 RX controller + +maintainers: + - Maxime Ripard <mripard@kernel.org> + +description: + The Cadence MIPI-CSI2 RX controller is a CSI-2 bridge supporting up to 4 CSI + lanes in input, and 4 different pixel streams in output. + +properties: + compatible: + items: + - enum: + - starfive,jh7110-csi2rx + - ti,j721e-csi2rx + - const: cdns,csi2rx + + reg: + maxItems: 1 + + interrupts: + maxItems: 2 + + interrupt-names: + items: + - const: error_irq + - const: irq + + clocks: + items: + - description: CSI2Rx system clock + - description: Gated Register bank clock for APB interface + - description: pixel Clock for Stream interface 0 + - description: pixel Clock for Stream interface 1 + - description: pixel Clock for Stream interface 2 + - description: pixel Clock for Stream interface 3 + + clock-names: + items: + - const: sys_clk + - const: p_clk + - const: pixel_if0_clk + - const: pixel_if1_clk + - const: pixel_if2_clk + - const: pixel_if3_clk + + resets: + items: + - description: CSI2Rx system reset + - description: Gated Register bank reset for APB interface + - description: pixel reset for Stream interface 0 + - description: pixel reset for Stream interface 1 + - description: pixel reset for Stream interface 2 + - description: pixel reset for Stream interface 3 + + reset-names: + items: + - const: sys + - const: reg_bank + - const: pixel_if0 + - const: pixel_if1 + - const: pixel_if2 + - const: pixel_if3 + + phys: + maxItems: 1 + description: MIPI D-PHY + + phy-names: + items: + - const: dphy + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + const: 4 + + clock-lanes: + const: 0 + + data-lanes: + minItems: 1 + maxItems: 4 + items: + maximum: 4 + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Stream 0 Output port node + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: + Stream 1 Output port node + + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: + Stream 2 Output port node + + port@4: + $ref: /schemas/graph.yaml#/properties/port + description: + Stream 3 Output port node + + required: + - port@0 + +required: + - compatible + - reg + - clocks + - clock-names + - ports + +additionalProperties: false + +examples: + - | + csi@d060000 { + compatible = "starfive,jh7110-csi2rx", "cdns,csi2rx"; + reg = <0x0d060000 0x1000>; + clocks = <&byteclock 7>, <&byteclock 6>, + <&coreclock 8>, <&coreclock 9>, + <&coreclock 10>, <&coreclock 11>; + clock-names = "sys_clk", "p_clk", + "pixel_if0_clk", "pixel_if1_clk", + "pixel_if2_clk", "pixel_if3_clk"; + resets = <&bytereset 9>, <&bytereset 4>, + <&corereset 5>, <&corereset 6>, + <&corereset 7>, <&corereset 8>; + reset-names = "sys", "reg_bank", + "pixel_if0", "pixel_if1", + "pixel_if2", "pixel_if3"; + phys = <&csi_phy>; + phy-names = "dphy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + csi2rx_in_sensor: endpoint { + remote-endpoint = <&sensor_out_csi2rx>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + + port@1 { + reg = <1>; + + csi2rx_out_grabber0: endpoint { + remote-endpoint = <&grabber0_in_csi2rx>; + }; + }; + + port@2 { + reg = <2>; + + csi2rx_out_grabber1: endpoint { + remote-endpoint = <&grabber1_in_csi2rx>; + }; + }; + + port@3 { + reg = <3>; + + csi2rx_out_grabber2: endpoint { + remote-endpoint = <&grabber2_in_csi2rx>; + }; + }; + + port@4 { + reg = <4>; + + csi2rx_out_grabber3: endpoint { + remote-endpoint = <&grabber3_in_csi2rx>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/cdns,csi2tx.txt b/Documentation/devicetree/bindings/media/cdns,csi2tx.txt new file mode 100644 index 000000000..751b9edf1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/cdns,csi2tx.txt @@ -0,0 +1,99 @@ +Cadence MIPI-CSI2 TX controller +=============================== + +The Cadence MIPI-CSI2 TX controller is a CSI-2 bridge supporting up to +4 CSI lanes in output, and up to 4 different pixel streams in input. + +Required properties: + - compatible: must be set to "cdns,csi2tx" or "cdns,csi2tx-1.3" + for version 1.3 of the controller, "cdns,csi2tx-2.1" for v2.1 + - reg: base address and size of the memory mapped region + - clocks: phandles to the clocks driving the controller + - clock-names: must contain: + * esc_clk: escape mode clock + * p_clk: register bank clock + * pixel_if[0-3]_clk: pixel stream output clock, one for each stream + implemented in hardware, between 0 and 3 + +Optional properties + - phys: phandle to the D-PHY. If it is set, phy-names need to be set + - phy-names: must contain "dphy" + +Required subnodes: + - ports: A ports node with one port child node per device input and output + port, in accordance with the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + port nodes are numbered as follows. + + Port Description + ----------------------------- + 0 CSI-2 output + 1 Stream 0 input + 2 Stream 1 input + 3 Stream 2 input + 4 Stream 3 input + + The stream input port nodes are optional if they are not + connected to anything at the hardware level or implemented + in the design. Since there is only one endpoint per port, + the endpoints are not numbered. + +Example: + +csi2tx: csi-bridge@0d0e1000 { + compatible = "cdns,csi2tx"; + reg = <0x0d0e1000 0x1000>; + clocks = <&byteclock>, <&byteclock>, + <&coreclock>, <&coreclock>, + <&coreclock>, <&coreclock>; + clock-names = "p_clk", "esc_clk", + "pixel_if0_clk", "pixel_if1_clk", + "pixel_if2_clk", "pixel_if3_clk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + csi2tx_out: endpoint { + remote-endpoint = <&remote_in>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + + port@1 { + reg = <1>; + + csi2tx_in_stream0: endpoint { + remote-endpoint = <&stream0_out>; + }; + }; + + port@2 { + reg = <2>; + + csi2tx_in_stream1: endpoint { + remote-endpoint = <&stream1_out>; + }; + }; + + port@3 { + reg = <3>; + + csi2tx_in_stream2: endpoint { + remote-endpoint = <&stream2_out>; + }; + }; + + port@4 { + reg = <4>; + + csi2tx_in_stream3: endpoint { + remote-endpoint = <&stream3_out>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/cec/amlogic,meson-gx-ao-cec.yaml b/Documentation/devicetree/bindings/media/cec/amlogic,meson-gx-ao-cec.yaml new file mode 100644 index 000000000..b1fab5341 --- /dev/null +++ b/Documentation/devicetree/bindings/media/cec/amlogic,meson-gx-ao-cec.yaml @@ -0,0 +1,92 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/cec/amlogic,meson-gx-ao-cec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Meson AO-CEC Controller + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +description: | + The Amlogic Meson AO-CEC module is present is Amlogic SoCs and its purpose is + to handle communication between HDMI connected devices over the CEC bus. + +properties: + compatible: + enum: + - amlogic,meson-gx-ao-cec # GXBB, GXL, GXM, G12A and SM1 AO_CEC_A module + - amlogic,meson-g12a-ao-cec # G12A AO_CEC_B module + - amlogic,meson-sm1-ao-cec # SM1 AO_CEC_B module + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + maxItems: 1 + + interrupts: + maxItems: 1 + +allOf: + - $ref: cec-common.yaml# + - if: + properties: + compatible: + contains: + enum: + - amlogic,meson-gx-ao-cec + + then: + properties: + clocks: + items: + - description: AO-CEC clock + + clock-names: + items: + - const: core + + - if: + properties: + compatible: + contains: + enum: + - amlogic,meson-g12a-ao-cec + - amlogic,meson-sm1-ao-cec + + then: + properties: + clocks: + items: + - description: AO-CEC clock generator source + + clock-names: + items: + - const: oscin + +required: + - compatible + - reg + - interrupts + - hdmi-phandle + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + cec_AO: cec@100 { + compatible = "amlogic,meson-gx-ao-cec"; + reg = <0x00100 0x14>; + interrupts = <199>; + clocks = <&clkc_cec>; + clock-names = "core"; + hdmi-phandle = <&hdmi_tx>; + }; diff --git a/Documentation/devicetree/bindings/media/cec/cec-common.yaml b/Documentation/devicetree/bindings/media/cec/cec-common.yaml new file mode 100644 index 000000000..6d5017d9b --- /dev/null +++ b/Documentation/devicetree/bindings/media/cec/cec-common.yaml @@ -0,0 +1,28 @@ +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/cec/cec-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: HDMI CEC Adapters Common Properties + +maintainers: + - Hans Verkuil <hverkuil@kernel.org> + +properties: + $nodename: + pattern: "^cec(@[0-9a-f]+|-[0-9]+)?$" + + hdmi-phandle: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to the HDMI controller. + + needs-hpd: + type: boolean + description: + The CEC support is only available when the HPD is high. Some boards only + let the CEC pin through if the HPD is high, for example if there is a + level converter that uses the HPD to power up or down. + +additionalProperties: true diff --git a/Documentation/devicetree/bindings/media/cec/cec-gpio.yaml b/Documentation/devicetree/bindings/media/cec/cec-gpio.yaml new file mode 100644 index 000000000..582c6c9ca --- /dev/null +++ b/Documentation/devicetree/bindings/media/cec/cec-gpio.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/cec/cec-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: HDMI CEC GPIO + +maintainers: + - Hans Verkuil <hverkuil@kernel.org> + +description: | + The HDMI CEC GPIO module supports CEC implementations where the CEC line is + hooked up to a pull-up GPIO line and - optionally - the HPD line is hooked up + to another GPIO line. + + Please note:: the maximum voltage for the CEC line is 3.63V, for the HPD and + 5V lines it is 5.3V. So you may need some sort of level conversion + circuitry when connecting them to a GPIO line. + +properties: + compatible: + const: cec-gpio + + cec-gpios: + maxItems: 1 + description: + GPIO that the CEC line is connected to. The line should be tagged as open + drain. + + hpd-gpios: + maxItems: 1 + description: + GPIO that the HPD line is connected to. Used for debugging HPD changes + when the CEC line is not associated with an HDMI receiver/transmitter. + + v5-gpios: + maxItems: 1 + description: + GPIO that the 5V line is connected to. Used for debugging changes on the + 5V line. + +required: + - compatible + - cec-gpios + +allOf: + - $ref: cec-common.yaml# + - if: + required: + - hdmi-phandle + then: + properties: + hpd-gpios: false + + - if: + required: + - hpd-gpios + then: + properties: + hdmi-phandle: false + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + cec { + compatible = "cec-gpio"; + cec-gpios = <&gpio 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + hpd-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + v5-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/media/cec/nvidia,tegra114-cec.yaml b/Documentation/devicetree/bindings/media/cec/nvidia,tegra114-cec.yaml new file mode 100644 index 000000000..6ef545b1d --- /dev/null +++ b/Documentation/devicetree/bindings/media/cec/nvidia,tegra114-cec.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/cec/nvidia,tegra114-cec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra HDMI CEC + +maintainers: + - Hans Verkuil <hverkuil@kernel.org> + +allOf: + - $ref: cec-common.yaml# + +properties: + compatible: + oneOf: + - enum: + - nvidia,tegra114-cec + - nvidia,tegra124-cec + - nvidia,tegra210-cec + - items: + - enum: + - nvidia,tegra186-cec + - nvidia,tegra194-cec + - const: nvidia,tegra210-cec + + clocks: + maxItems: 1 + + clock-names: + items: + - const: cec + + interrupts: + maxItems: 1 + + reg: + maxItems: 1 + +required: + - compatible + - clocks + - clock-names + - hdmi-phandle + - interrupts + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/tegra124-car.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + cec@70015000 { + compatible = "nvidia,tegra124-cec"; + reg = <0x70015000 0x00001000>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_CEC>; + clock-names = "cec"; + hdmi-phandle = <&hdmi>; + }; diff --git a/Documentation/devicetree/bindings/media/cec/samsung,s5p-cec.yaml b/Documentation/devicetree/bindings/media/cec/samsung,s5p-cec.yaml new file mode 100644 index 000000000..016c8a77c --- /dev/null +++ b/Documentation/devicetree/bindings/media/cec/samsung,s5p-cec.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/cec/samsung,s5p-cec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5PV210 and Exynos HDMI CEC + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Marek Szyprowski <m.szyprowski@samsung.com> + +allOf: + - $ref: cec-common.yaml# + +properties: + compatible: + const: samsung,s5p-cec + + clocks: + maxItems: 1 + + clock-names: + items: + - const: hdmicec + + interrupts: + maxItems: 1 + + samsung,syscon-phandle: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to PMU system controller interface + + reg: + maxItems: 1 + +required: + - compatible + - clocks + - clock-names + - hdmi-phandle + - interrupts + - samsung,syscon-phandle + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos5420.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + cec@101b0000 { + compatible = "samsung,s5p-cec"; + reg = <0x101B0000 0x200>; + + clocks = <&clock CLK_HDMI_CEC>; + clock-names = "hdmicec"; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; + hdmi-phandle = <&hdmi>; + needs-hpd; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_cec>; + samsung,syscon-phandle = <&pmu_system_controller>; + }; diff --git a/Documentation/devicetree/bindings/media/cec/st,stih-cec.yaml b/Documentation/devicetree/bindings/media/cec/st,stih-cec.yaml new file mode 100644 index 000000000..aeddf16ed --- /dev/null +++ b/Documentation/devicetree/bindings/media/cec/st,stih-cec.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/cec/st,stih-cec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STIH4xx HDMI CEC + +maintainers: + - Alain Volmat <alain.volmat@foss.st.com> + +allOf: + - $ref: cec-common.yaml# + +properties: + compatible: + const: st,stih-cec + + clocks: + maxItems: 1 + + clock-names: + items: + - const: cec-clk + + interrupts: + maxItems: 1 + + interrupt-names: + items: + - const: cec-irq + + resets: + maxItems: 1 + + reg: + maxItems: 1 + +required: + - compatible + - clocks + - hdmi-phandle + - interrupts + - resets + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/reset/stih407-resets.h> + + cec@94a087c { + compatible = "st,stih-cec"; + reg = <0x94a087c 0x64>; + + clocks = <&clk_sysin>; + clock-names = "cec-clk"; + hdmi-phandle = <&sti_hdmi>; + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cec-irq"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_cec0_default>; + resets = <&softreset STIH407_LPM_SOFTRESET>; + }; diff --git a/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml b/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml new file mode 100644 index 000000000..1d930d9e1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/cec/st,stm32-cec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32 CEC + +maintainers: + - Yannick Fertre <yannick.fertre@foss.st.com> + +properties: + compatible: + const: st,stm32-cec + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Module Clock + - description: Bus Clock + + clock-names: + items: + - const: cec + - const: hdmi-cec + + access-controllers: + minItems: 1 + maxItems: 2 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/stm32mp1-clks.h> + cec: cec@40006c00 { + compatible = "st,stm32-cec"; + reg = <0x40006c00 0x400>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc CEC_K>, <&clk_lse>; + clock-names = "cec", "hdmi-cec"; + }; + +... diff --git a/Documentation/devicetree/bindings/media/cnm,wave521c.yaml b/Documentation/devicetree/bindings/media/cnm,wave521c.yaml new file mode 100644 index 000000000..6cd33dfd0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/cnm,wave521c.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/cnm,wave521c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Chips&Media Wave 5 Series multi-standard codec IP + +maintainers: + - Nas Chung <nas.chung@chipsnmedia.com> + - Jackson Lee <jackson.lee@chipsnmedia.com> + +description: + The Chips&Media WAVE codec IP is a multi format video encoder/decoder + +properties: + compatible: + items: + - enum: + - ti,j721s2-wave521c + - const: cnm,wave521c + + reg: + maxItems: 1 + + clocks: + items: + - description: VCODEC clock + + interrupts: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + sram: + maxItems: 1 + description: + The VPU uses the SRAM to store some of the reference data instead of + storing it on DMA memory. It is mainly used for the purpose of reducing + bandwidth. + +required: + - compatible + - reg + - clocks + +additionalProperties: false + +examples: + - | + vpu: video-codec@12345678 { + compatible = "ti,j721s2-wave521c", "cnm,wave521c"; + reg = <0x12345678 0x1000>; + clocks = <&clks 42>; + interrupts = <42>; + sram = <&sram>; + }; diff --git a/Documentation/devicetree/bindings/media/coda.yaml b/Documentation/devicetree/bindings/media/coda.yaml new file mode 100644 index 000000000..c9d5adbc8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/coda.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/coda.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Chips&Media Coda multi-standard codec IP + +maintainers: + - Philipp Zabel <p.zabel@pengutronix.de> + +description: |- + Coda codec IPs are present in i.MX SoCs in various versions, + called VPU (Video Processing Unit). + +properties: + compatible: + oneOf: + - items: + - const: fsl,imx27-vpu + - const: cnm,codadx6 + - items: + - const: fsl,imx51-vpu + - const: cnm,codahx4 + - items: + - const: fsl,imx53-vpu + - const: cnm,coda7541 + - items: + - enum: + - fsl,imx6dl-vpu + - fsl,imx6q-vpu + - const: cnm,coda960 + + reg: + maxItems: 1 + + clocks: + items: + - description: PER clock + - description: AHB interface clock + + clock-names: + items: + - const: per + - const: ahb + + interrupts: + minItems: 1 + items: + - description: BIT processor interrupt + - description: JPEG unit interrupt + + interrupt-names: + minItems: 1 + items: + - const: bit + - const: jpeg + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + iram: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle pointing to the SRAM device node + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + const: cnm,coda960 + then: + properties: + interrupts: + minItems: 2 + + interrupt-names: + minItems: 2 + else: + properties: + interrupts: + maxItems: 1 + + power-domains: false + +examples: + - | + vpu: video-codec@63ff4000 { + compatible = "fsl,imx53-vpu", "cnm,coda7541"; + reg = <0x63ff4000 0x1000>; + interrupts = <9>; + clocks = <&clks 63>, <&clks 63>; + clock-names = "per", "ahb"; + iram = <&ocram>; + }; diff --git a/Documentation/devicetree/bindings/media/fsl,imx-capture-subsystem.yaml b/Documentation/devicetree/bindings/media/fsl,imx-capture-subsystem.yaml new file mode 100644 index 000000000..25e65a344 --- /dev/null +++ b/Documentation/devicetree/bindings/media/fsl,imx-capture-subsystem.yaml @@ -0,0 +1,37 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/fsl,imx-capture-subsystem.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale i.MX Media Video Device + +description: + This is the media controller node for video capture support. It is a + virtual device that lists the camera serial interface nodes that the + media device will control + +maintainers: + - Frank Li <Frank.Li@nxp.com> + +properties: + compatible: + const: fsl,imx-capture-subsystem + + ports: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + Should contain a list of phandles pointing to camera + sensor interface ports of IPU devices. + +required: + - compatible + +additionalProperties: false + +examples: + - | + capture-subsystem { + compatible = "fsl,imx-capture-subsystem"; + ports = <&ipu1_csi0>, <&ipu1_csi1>; + }; diff --git a/Documentation/devicetree/bindings/media/fsl,imx6-mipi-csi2.yaml b/Documentation/devicetree/bindings/media/fsl,imx6-mipi-csi2.yaml new file mode 100644 index 000000000..65255f576 --- /dev/null +++ b/Documentation/devicetree/bindings/media/fsl,imx6-mipi-csi2.yaml @@ -0,0 +1,143 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/fsl,imx6-mipi-csi2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MIPI CSI-2 Receiver core in the i.MX SoC + +description: + This is the device node for the MIPI CSI-2 Receiver core in the i.MX + SoC. This is a Synopsys Designware MIPI CSI-2 host controller core + combined with a D-PHY core mixed into the same register block. In + addition this device consists of an i.MX-specific "CSI2IPU gasket" + glue logic, also controlled from the same register block. The CSI2IPU + gasket demultiplexes the four virtual channel streams from the host + controller's 32-bit output image bus onto four 16-bit parallel busses + to the i.MX IPU CSIs. + +maintainers: + - Frank Li <Frank.Li@nxp.com> + +properties: + compatible: + const: fsl,imx6-mipi-csi2 + + reg: + maxItems: 1 + + clocks: + items: + - description: hsi_tx (the D-PHY clock) + - description: video_27m (D-PHY PLL reference clock) + - description: eim_podf; + + clock-names: + items: + - const: dphy + - const: ref + - const: pix + + interrupts: + items: + - description: CSI-2 ERR1 irq + - description: CSI-2 ERR2 irq + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + const: 0 + + data-lanes: + minItems: 1 + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - data-lanes + +patternProperties: + '^port@[1-4]$': + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + ports 1 through 4 are output ports connecting with parallel bus sink + endpoint nodes and correspond to the four MIPI CSI-2 virtual channel + outputs. + + properties: + endpoint@0: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + endpoint@1: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx6qdl-clock.h> + + mipi@21dc000 { + compatible = "fsl,imx6-mipi-csi2"; + reg = <0x021dc000 0x4000>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clks IMX6QDL_CLK_HSI_TX>, + <&clks IMX6QDL_CLK_VIDEO_27M>, + <&clks IMX6QDL_CLK_EIM_PODF>; + clock-names = "dphy", "ref", "pix"; + + port@0 { + reg = <0>; + + endpoint { + remote-endpoint = <&ov5640_to_mipi_csi2>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + + port@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + endpoint@0 { + reg = <0>; + remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc0>; + }; + + endpoint@1 { + reg = <1>; + remote-endpoint = <&ipu1_csi1_mux_from_mipi_vc0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/fsl,imx6q-vdoa.yaml b/Documentation/devicetree/bindings/media/fsl,imx6q-vdoa.yaml new file mode 100644 index 000000000..988a5b3a6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/fsl,imx6q-vdoa.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/fsl,imx6q-vdoa.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Video Data Order Adapter + +description: + The Video Data Order Adapter (VDOA) is present on the i.MX6q. Its sole purpose + is to reorder video data from the macroblock tiled order produced by the CODA + 960 VPU to the conventional raster-scan order for scanout. + +maintainers: + - Frank Li <Frank.Li@nxp.com> + +properties: + compatible: + const: fsl,imx6q-vdoa + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/imx6qdl-clock.h> + + vdoa@21e4000 { + compatible = "fsl,imx6q-vdoa"; + reg = <0x021e4000 0x4000>; + interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_VDOA>; + }; diff --git a/Documentation/devicetree/bindings/media/fsl,imx6ull-pxp.yaml b/Documentation/devicetree/bindings/media/fsl,imx6ull-pxp.yaml new file mode 100644 index 000000000..3f4774445 --- /dev/null +++ b/Documentation/devicetree/bindings/media/fsl,imx6ull-pxp.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/fsl,imx6ull-pxp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Pixel Pipeline + +maintainers: + - Philipp Zabel <p.zabel@pengutronix.de> + - Michael Tretter <m.tretter@pengutronix.de> + +description: + The Pixel Pipeline (PXP) is a memory-to-memory graphics processing engine + that supports scaling, colorspace conversion, alpha blending, rotation, and + pixel conversion via lookup table. Different versions are present on various + i.MX SoCs from i.MX23 to i.MX7. + +properties: + compatible: + oneOf: + - enum: + - fsl,imx6ul-pxp + - fsl,imx6ull-pxp + - fsl,imx7d-pxp + - items: + - enum: + - fsl,imx6sll-pxp + - fsl,imx6sx-pxp + - const: fsl,imx6ull-pxp + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 2 + + clocks: + maxItems: 1 + + clock-names: + const: axi + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +allOf: + - if: + properties: + compatible: + contains: + enum: + - fsl,imx6sx-pxp + - fsl,imx6ul-pxp + then: + properties: + interrupts: + maxItems: 1 + else: + properties: + interrupts: + minItems: 2 + maxItems: 2 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx6ul-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pxp: pxp@21cc000 { + compatible = "fsl,imx6ull-pxp"; + reg = <0x021cc000 0x4000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "axi"; + clocks = <&clks IMX6UL_CLK_PXP>; + }; diff --git a/Documentation/devicetree/bindings/media/fsl,imx8qm-isi.yaml b/Documentation/devicetree/bindings/media/fsl,imx8qm-isi.yaml new file mode 100644 index 000000000..93f527e22 --- /dev/null +++ b/Documentation/devicetree/bindings/media/fsl,imx8qm-isi.yaml @@ -0,0 +1,117 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/fsl,imx8qm-isi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: i.MX8QM Image Sensing Interface + +maintainers: + - Frank Li <Frank.Li@nxp.com> + +description: + The Image Sensing Interface (ISI) combines image processing pipelines with + DMA engines to process and capture frames originating from a variety of + sources. The inputs to the ISI go through Pixel Link interfaces, and their + number and nature is SoC-dependent. They cover both capture interfaces (MIPI + CSI-2 RX, HDMI RX, ...) and display engine outputs for writeback support. + +properties: + compatible: + enum: + - fsl,imx8qm-isi + + reg: + maxItems: 1 + + clocks: + maxItems: 8 + + clock-names: + items: + - const: per0 + - const: per1 + - const: per2 + - const: per3 + - const: per4 + - const: per5 + - const: per6 + - const: per7 + + interrupts: + maxItems: 8 + + power-domains: + maxItems: 8 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: MIPI CSI-2 RX 0 + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: MIPI CSI-2 RX 1 + port@4: + $ref: /schemas/graph.yaml#/properties/port + description: HDMI RX + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + - power-domains + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/imx8-clock.h> + #include <dt-bindings/clock/imx8-lpcg.h> + #include <dt-bindings/firmware/imx/rsrc.h> + + image-controller@58100000 { + compatible = "fsl,imx8qm-isi"; + reg = <0x58100000 0x80000>; + interrupts = <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pdma0_lpcg IMX_LPCG_CLK_0>, + <&pdma1_lpcg IMX_LPCG_CLK_0>, + <&pdma2_lpcg IMX_LPCG_CLK_0>, + <&pdma3_lpcg IMX_LPCG_CLK_0>, + <&pdma4_lpcg IMX_LPCG_CLK_0>, + <&pdma5_lpcg IMX_LPCG_CLK_0>, + <&pdma6_lpcg IMX_LPCG_CLK_0>, + <&pdma7_lpcg IMX_LPCG_CLK_0>; + clock-names = "per0", "per1", "per2", "per3", + "per4", "per5", "per6", "per7"; + power-domains = <&pd IMX_SC_R_ISI_CH0>, <&pd IMX_SC_R_ISI_CH1>, + <&pd IMX_SC_R_ISI_CH2>, <&pd IMX_SC_R_ISI_CH3>, + <&pd IMX_SC_R_ISI_CH4>, <&pd IMX_SC_R_ISI_CH5>, + <&pd IMX_SC_R_ISI_CH6>, <&pd IMX_SC_R_ISI_CH7>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@2 { + reg = <2>; + endpoint { + remote-endpoint = <&mipi_csi0_out>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/fsl,imx8qxp-isi.yaml b/Documentation/devicetree/bindings/media/fsl,imx8qxp-isi.yaml new file mode 100644 index 000000000..bb41996bd --- /dev/null +++ b/Documentation/devicetree/bindings/media/fsl,imx8qxp-isi.yaml @@ -0,0 +1,106 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/fsl,imx8qxp-isi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: i.MX8QXP Image Sensing Interface + +maintainers: + - Frank Li <Frank.Li@nxp.com> + +description: + The Image Sensing Interface (ISI) combines image processing pipelines with + DMA engines to process and capture frames originating from a variety of + sources. The inputs to the ISI go through Pixel Link interfaces, and their + number and nature is SoC-dependent. They cover both capture interfaces (MIPI + CSI-2 RX, HDMI RX, ...) and display engine outputs for writeback support. + +properties: + compatible: + enum: + - fsl,imx8qxp-isi + + reg: + maxItems: 1 + + clocks: + maxItems: 6 + + clock-names: + items: + - const: per0 + - const: per1 + - const: per2 + - const: per3 + - const: per4 + - const: per5 + + interrupts: + maxItems: 6 + + power-domains: + maxItems: 6 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: MIPI CSI-2 RX 0 + port@6: + $ref: /schemas/graph.yaml#/properties/port + description: CSI-2 Parallel RX + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + - power-domains + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/imx8-clock.h> + #include <dt-bindings/clock/imx8-lpcg.h> + #include <dt-bindings/firmware/imx/rsrc.h> + + image-controller@58100000 { + compatible = "fsl,imx8qxp-isi"; + reg = <0x58100000 0x60000>; + interrupts = <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pdma0_lpcg IMX_LPCG_CLK_0>, + <&pdma1_lpcg IMX_LPCG_CLK_0>, + <&pdma2_lpcg IMX_LPCG_CLK_0>, + <&pdma3_lpcg IMX_LPCG_CLK_0>, + <&pdma4_lpcg IMX_LPCG_CLK_0>, + <&pdma5_lpcg IMX_LPCG_CLK_0>; + clock-names = "per0", "per1", "per2", "per3", "per4", "per5"; + power-domains = <&pd IMX_SC_R_ISI_CH0>, <&pd IMX_SC_R_ISI_CH1>, + <&pd IMX_SC_R_ISI_CH2>, <&pd IMX_SC_R_ISI_CH3>, + <&pd IMX_SC_R_ISI_CH4>, <&pd IMX_SC_R_ISI_CH5>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@2 { + reg = <2>; + endpoint { + remote-endpoint = <&mipi_csi0_out>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/gpio-ir-receiver.yaml b/Documentation/devicetree/bindings/media/gpio-ir-receiver.yaml new file mode 100644 index 000000000..008c007ed --- /dev/null +++ b/Documentation/devicetree/bindings/media/gpio-ir-receiver.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/gpio-ir-receiver.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO Based IR receiver + +maintainers: + - Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> + +allOf: + - $ref: rc.yaml# + +properties: + compatible: + const: gpio-ir-receiver + + gpios: + maxItems: 1 + + linux,autosuspend-period: + description: autosuspend delay time in milliseconds + $ref: /schemas/types.yaml#/definitions/uint32 + + wakeup-source: + description: IR receiver can wake-up the system. + +required: + - compatible + - gpios + +unevaluatedProperties: false + +examples: + - | + ir-receiver { + compatible = "gpio-ir-receiver"; + gpios = <&gpio0 19 1>; + linux,rc-map-name = "rc-rc6-mce"; + linux,autosuspend-period = <125>; + }; +... diff --git a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt new file mode 100644 index 000000000..ca4cf7746 --- /dev/null +++ b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt @@ -0,0 +1,26 @@ +Device-Tree bindings for hix5hd2 ir IP + +Required properties: + - compatible: Should contain "hisilicon,hix5hd2-ir", or: + - "hisilicon,hi3796cv300-ir" for Hi3796CV300 IR device. + - reg: Base physical address of the controller and length of memory + mapped region. + - interrupts: interrupt-specifier for the sole interrupt generated by + the device. The interrupt specifier format depends on the interrupt + controller parent. + - clocks: clock phandle and specifier pair. + +Optional properties: + - linux,rc-map-name: see rc.txt file in the same directory. + - hisilicon,power-syscon: DEPRECATED. Don't use this in new dts files. + Provide correct clocks instead. + +Example node: + + ir: ir@f8001000 { + compatible = "hisilicon,hix5hd2-ir"; + reg = <0xf8001000 0x1000>; + interrupts = <0 47 4>; + clocks = <&clock HIX5HD2_IR_CLOCK>; + linux,rc-map-name = "rc-tivo"; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adi,ad5820.yaml b/Documentation/devicetree/bindings/media/i2c/adi,ad5820.yaml new file mode 100644 index 000000000..0c8f24f69 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adi,ad5820.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/adi,ad5820.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD5820 autofocus coil + +maintainers: + - Pavel Machek <pavel@ucw.cz> + +description: + The AD5820 is a current sink driver designed for precise control of + voice coil motors (VCMs) in camera autofocus systems. + +properties: + compatible: + enum: + - adi,ad5820 + - adi,ad5821 + - adi,ad5823 + + reg: + maxItems: 1 + + enable-gpios: + maxItems: 1 + description: + GPIO spec for the XSHUTDOWN pin. The XSHUTDOWN signal is active low, + a high level on the pin enables the device. + + VANA-supply: + description: supply of voltage for VANA pin + +required: + - compatible + - reg + - VANA-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + coil@c { + compatible = "adi,ad5820"; + reg = <0x0c>; + + enable-gpios = <&msmgpio 26 GPIO_ACTIVE_HIGH>; + VANA-supply = <&vaux4>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adi,adp1653.txt b/Documentation/devicetree/bindings/media/i2c/adi,adp1653.txt new file mode 100644 index 000000000..4cce0de40 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adi,adp1653.txt @@ -0,0 +1,38 @@ +* Analog Devices ADP1653 flash LED driver + +Required Properties: + + - compatible: Must contain "adi,adp1653" + + - reg: I2C slave address + + - enable-gpios: Specifier of the GPIO connected to EN pin + +There are two LED outputs available - flash and indicator. One LED is +represented by one child node, nodes need to be named "flash" and "indicator". + +Required properties of the LED child node: +- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt + +Required properties of the flash LED child node: + +- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt +- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt +- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt + +Example: + + adp1653: led-controller@30 { + compatible = "adi,adp1653"; + reg = <0x30>; + enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; /* 88 */ + + flash { + flash-timeout-us = <500000>; + flash-max-microamp = <320000>; + led-max-microamp = <50000>; + }; + indicator { + led-max-microamp = <17500>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adi,adv7180.yaml b/Documentation/devicetree/bindings/media/i2c/adi,adv7180.yaml new file mode 100644 index 000000000..5f8f3b3de --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adi,adv7180.yaml @@ -0,0 +1,284 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/adi,adv7180.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADV7180 analog video decoder family + +maintainers: + - Lars-Peter Clausen <lars@metafoo.de> + +description: + The adv7180 family devices are used to capture analog video to different + digital interfaces like MIPI CSI-2 or parallel video. + +properties: + compatible: + items: + - enum: + - adi,adv7180 + - adi,adv7180cp + - adi,adv7180st + - adi,adv7182 + - adi,adv7280 + - adi,adv7280-m + - adi,adv7281 + - adi,adv7281-m + - adi,adv7281-ma + - adi,adv7282 + - adi,adv7282-m + + reg: + minItems: 1 + items: + - description: main register map + - description: VPP or CSI register map + - description: CSI register map + description: + The ADV7180 family may have up to three register maps. All chips have + the main register map. The availability of the CSI and VPP register maps + depends on the chip variant. + + The addresses of the CSI and VPP register maps are programmable by + software. They depend on the board layout and other devices on the I2C + bus and are determined by the hardware designer to avoid address + conflicts on the I2C bus. + + reg-names: + minItems: 1 + items: + - const: main + - enum: [ csi, vpp ] + - const: csi + + powerdown-gpios: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + adv,force-bt656-4: + deprecated: true + description: + Indicates that the output is a BT.656-4 compatible stream. + type: boolean + + adi,force-bt656-4: + description: + Indicates that the output is a BT.656-4 compatible stream. + type: boolean + + interrupts: + items: + - description: The GPIO connected to the INTRQ pin. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + ports: true + +additionalProperties: false + +required: + - compatible + - reg + +allOf: + - if: + properties: + compatible: + enum: + - adi,adv7180 + - adi,adv7182 + - adi,adv7280 + - adi,adv7280-m + - adi,adv7281 + - adi,adv7281-m + - adi,adv7281-ma + - adi,adv7282 + - adi,adv7282-m + then: + required: + - port + + - if: + properties: + compatible: + contains: + const: adi,adv7180cp + then: + properties: + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: Output port + + patternProperties: + "^port@[0-2]$": + $ref: /schemas/graph.yaml#/properties/port + description: Input port + + required: + - port@3 + + required: + - ports + + - if: + properties: + compatible: + contains: + const: adi,adv7180st + then: + properties: + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@6: + $ref: /schemas/graph.yaml#/properties/port + description: Output port + + patternProperties: + "^port@[0-5]$": + $ref: /schemas/graph.yaml#/properties/port + description: Input port + + required: + - port@6 + + required: + - ports + + - if: + properties: + compatible: + contains: + enum: + - adi,adv7180 + - adi,adv7180cp + - adi,adv7180st + - adi,adv7182 + then: + properties: + reg: + maxItems: 1 + + reg-names: + maxItems: 1 + + - if: + properties: + compatible: + contains: + enum: + - adi,adv7281 + - adi,adv7281-m + - adi,adv7281-ma + then: + properties: + reg: + minItems: 1 + maxItems: 2 + + reg-names: + minItems: 1 + items: + - const: main + - const: csi + + - if: + properties: + compatible: + contains: + enum: + - adi,adv7280 + - adi,adv7282 + then: + properties: + reg: + minItems: 1 + maxItems: 2 + + reg-names: + minItems: 1 + items: + - const: main + - const: vpp + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + composite-in@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + + port { + adv7180: endpoint { + bus-width = <8>; + remote-endpoint = <&vin1ep>; + }; + }; + }; + + }; + + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + composite-in@20 { + compatible = "adi,adv7180cp"; + reg = <0x20>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7180_in: endpoint { + remote-endpoint = <&composite_con_in>; + }; + }; + + port@3 { + reg = <3>; + adv7180_out: endpoint { + remote-endpoint = <&vin4_in>; + }; + }; + }; + }; + }; + + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + composite-in@20 { + compatible = "adi,adv7280-m"; + reg = <0x20>, <0x42>, <0x44>; + reg-names = "main", "vpp", "csi"; + + port { + adv7280_out: endpoint { + bus-width = <8>; + remote-endpoint = <&vin1ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adi,adv7343.txt b/Documentation/devicetree/bindings/media/i2c/adi,adv7343.txt new file mode 100644 index 000000000..5653bc242 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adi,adv7343.txt @@ -0,0 +1,48 @@ +* Analog Devices adv7343 video encoder + +The ADV7343 are high speed, digital-to-analog video encoders in a 64-lead LQFP +package. Six high speed, 3.3 V, 11-bit video DACs provide support for composite +(CVBS), S-Video (Y-C), and component (YPrPb/RGB) analog outputs in standard +definition (SD), enhanced definition (ED), or high definition (HD) video +formats. + +Required Properties : +- compatible: Must be "adi,adv7343" + +Optional Properties : +- adi,power-mode-sleep-mode: on enable the current consumption is reduced to + micro ampere level. All DACs and the internal PLL + circuit are disabled. +- adi,power-mode-pll-ctrl: PLL and oversampling control. This control allows + internal PLL 1 circuit to be powered down and the + oversampling to be switched off. +- ad,adv7343-power-mode-dac: array configuring the power on/off DAC's 1..6, + 0 = OFF and 1 = ON, Default value when this + property is not specified is <0 0 0 0 0 0>. +- ad,adv7343-sd-config-dac-out: array configure SD DAC Output's 1 and 2, 0 = OFF + and 1 = ON, Default value when this property is + not specified is <0 0>. + +Example: + +i2c0@1c22000 { + ... + ... + + adv7343@2a { + compatible = "adi,adv7343"; + reg = <0x2a>; + + port { + adv7343_1: endpoint { + adi,power-mode-sleep-mode; + adi,power-mode-pll-ctrl; + /* Use DAC1..3, DAC6 */ + adi,dac-enable = <1 1 1 0 0 1>; + /* Use SD DAC output 1 */ + adi,sd-dac-enable = <1 0>; + }; + }; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/media/i2c/adi,adv748x.yaml b/Documentation/devicetree/bindings/media/i2c/adi,adv748x.yaml new file mode 100644 index 000000000..254987350 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adi,adv748x.yaml @@ -0,0 +1,212 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/adi,adv748x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADV748X video decoder with HDMI receiver + +maintainers: + - Kieran Bingham <kieran.bingham@ideasonboard.com> + - Niklas Söderlund <niklas.soderlund@ragnatech.se> + +description: + The ADV7481 and ADV7482 are multi format video decoders with an integrated + HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB + from three input sources HDMI, analog and TTL. + +properties: + compatible: + items: + - enum: + - adi,adv7481 + - adi,adv7482 + + reg: + minItems: 1 + maxItems: 12 + description: + The ADV748x has up to twelve 256-byte maps that can be accessed via the + main I2C ports. Each map has it own I2C address and acts as a standard + slave device on the I2C bus. The main address is mandatory, others are + optional and remain at default values if not specified. + + reg-names: + minItems: 1 + items: + - const: main + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ] + + interrupts: true + + interrupt-names: true + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + patternProperties: + "^port@[0-7]$": + $ref: /schemas/graph.yaml#/properties/port + description: Input port nodes for analog inputs AIN[0-7]. + + properties: + port@8: + $ref: /schemas/graph.yaml#/properties/port + description: Input port node for HDMI. + + port@9: + $ref: /schemas/graph.yaml#/properties/port + description: Input port node for TTL. + + port@a: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Output port node, single endpoint describing the CSI-2 transmitter TXA. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - clock-lanes + - data-lanes + + port@b: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Output port node, single endpoint describing the CSI-2 transmitter TXB. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + maxItems: 1 + + required: + - clock-lanes + - data-lanes + +allOf: + - if: + properties: + compatible: + contains: + const: adi,adv7481 + then: + properties: + interrupts: + minItems: 1 + maxItems: 3 + + interrupt-names: + minItems: 1 + maxItems: 3 + items: + enum: [ intrq1, intrq2, intrq3 ] + else: + properties: + interrupts: + minItems: 1 + maxItems: 2 + + interrupt-names: + minItems: 1 + maxItems: 2 + items: + enum: [ intrq1, intrq2 ] + +additionalProperties: false + +required: + - compatible + - reg + - ports + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + video-receiver@70 { + compatible = "adi,adv7482"; + reg = <0x70 0x71 0x72 0x73 0x74 0x75 + 0x60 0x61 0x62 0x63 0x64 0x65>; + reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater", + "infoframe", "cbus", "cec", "sdp", "txa", "txb"; + + interrupt-parent = <&gpio6>; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>, <31 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "intrq1", "intrq2"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@7 { + reg = <7>; + + adv7482_ain7: endpoint { + remote-endpoint = <&cvbs_in>; + }; + }; + + port@8 { + reg = <8>; + + adv7482_hdmi: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + + port@a { + reg = <10>; + + adv7482_txa: endpoint { + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + + port@b { + reg = <11>; + + adv7482_txb: endpoint { + clock-lanes = <0>; + data-lanes = <1>; + remote-endpoint = <&csi20_in>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adi,adv7604.yaml b/Documentation/devicetree/bindings/media/i2c/adi,adv7604.yaml new file mode 100644 index 000000000..f8d9889db --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adi,adv7604.yaml @@ -0,0 +1,158 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/adi,adv7604.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADV7604/10/11/12 video decoder with HDMI receiver + +maintainers: + - Hans Verkuil <hverkuil@kernel.org> + +description: + The ADV7604 and ADV7610/11/12 are multiformat video decoders with + an integrated HDMI receiver. The ADV7604 has four multiplexed HDMI inputs + and one analog input, and the ADV7610/11 have one HDMI input and no analog + input. The ADV7612 is similar to the ADV7610/11 but has 2 HDMI inputs. + + These device tree bindings support the ADV7610/11/12 only at the moment. + +properties: + compatible: + items: + - enum: + - adi,adv7610 + - adi,adv7611 + - adi,adv7612 + + reg: + minItems: 1 + maxItems: 13 + + reg-names: + minItems: 1 + items: + - const: main + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ] + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + hpd-gpios: + minItems: 1 + description: + References to the GPIOs that control the HDMI hot-plug detection pins, + one per HDMI input. The active flag indicates the GPIO level that + enables hot-plug detection. + + default-input: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1 ] + description: + Select which input is selected after reset. + + ports: true + +required: + - compatible + - reg + - ports + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + const: adi,adv7611 + then: + properties: + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: Input port + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Output port + + required: + - port@1 + + - if: + properties: + compatible: + contains: + const: adi,adv7612 + then: + properties: + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: Output port + + patternProperties: + "^port@[0-1]$": + $ref: /schemas/graph.yaml#/properties/port + description: Input port + + required: + - port@2 + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hdmi_receiver@4c { + compatible = "adi,adv7611"; + /* + * The edid page will be accessible @ 0x66 on the I2C bus. All + * other maps will retain their default addresses. + */ + reg = <0x4c>, <0x66>; + reg-names = "main", "edid"; + + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; + default-input = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + }; + + port@1 { + reg = <1>; + hdmi_in: endpoint { + remote-endpoint = <&ccdc_in>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/alliedvision,alvium-csi2.yaml b/Documentation/devicetree/bindings/media/i2c/alliedvision,alvium-csi2.yaml new file mode 100644 index 000000000..ae48dd4ab --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/alliedvision,alvium-csi2.yaml @@ -0,0 +1,81 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/alliedvision,alvium-csi2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allied Vision Alvium Camera + +maintainers: + - Tommaso Merciai <tomm.merciai@gmail.com> + - Martin Hecht <mhecht73@gmail.com> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: alliedvision,alvium-csi2 + + reg: + maxItems: 1 + + vcc-ext-in-supply: + description: | + The regulator that supplies power to the VCC_EXT_IN pins. + + port: + description: Digital Output Port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + + data-lanes: + minItems: 1 + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - vcc-ext-in-supply + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + alvium: camera@3c { + compatible = "alliedvision,alvium-csi2"; + reg = <0x3c>; + vcc-ext-in-supply = <®_vcc_ext_in>; + + port { + alvium_out: endpoint { + remote-endpoint = <&mipi_csi_0_in>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <681250000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9p031.yaml b/Documentation/devicetree/bindings/media/i2c/aptina,mt9p031.yaml new file mode 100644 index 000000000..be00de2f2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/aptina,mt9p031.yaml @@ -0,0 +1,109 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/aptina,mt9p031.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Aptina 1/2.5-Inch 5Mp CMOS Digital Image Sensor + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: | + The Aptina MT9P031 is a 1/2.5-inch CMOS active pixel digital image sensor + with an active array size of 2592H x 1944V. It is programmable through a + simple two-wire serial interface. + +properties: + compatible: + enum: + - aptina,mt9p006 + - aptina,mt9p031 + - aptina,mt9p031m + + reg: + description: I2C device address + maxItems: 1 + + clocks: + maxItems: 1 + + vdd-supply: + description: Digital supply voltage, 1.8 V + + vdd_io-supply: + description: I/O supply voltage, 1.8 or 2.8 V + + vaa-supply: + description: Analog supply voltage, 2.8 V + + reset-gpios: + maxItems: 1 + description: Chip reset GPIO + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + input-clock-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 6000000 + maximum: 96000000 + description: Input clock frequency + + pixel-clock-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 96000000 + description: Target pixel clock frequency + + pclk-sample: + default: 0 + + required: + - input-clock-frequency + - pixel-clock-frequency + +required: + - compatible + - reg + - clocks + - vdd-supply + - vdd_io-supply + - vaa-supply + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + mt9p031@5d { + compatible = "aptina,mt9p031"; + reg = <0x5d>; + reset-gpios = <&gpio_sensor 0 0>; + + clocks = <&sensor_clk>; + + vdd-supply = <®_vdd>; + vdd_io-supply = <®_vdd_io>; + vaa-supply = <®_vaa>; + + port { + mt9p031_1: endpoint { + input-clock-frequency = <6000000>; + pixel-clock-frequency = <96000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9v032.txt b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v032.txt new file mode 100644 index 000000000..100f0ae43 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v032.txt @@ -0,0 +1,41 @@ +* Aptina 1/3-Inch WVGA CMOS Digital Image Sensor + +The Aptina MT9V032 is a 1/3-inch CMOS active pixel digital image sensor with +an active array size of 752H x 480V. It is programmable through a simple +two-wire serial interface. + +Required Properties: + +- compatible: value should be either one among the following + (a) "aptina,mt9v022" for MT9V022 color sensor + (b) "aptina,mt9v022m" for MT9V022 monochrome sensor + (c) "aptina,mt9v024" for MT9V024 color sensor + (d) "aptina,mt9v024m" for MT9V024 monochrome sensor + (e) "aptina,mt9v032" for MT9V032 color sensor + (f) "aptina,mt9v032m" for MT9V032 monochrome sensor + (g) "aptina,mt9v034" for MT9V034 color sensor + (h) "aptina,mt9v034m" for MT9V034 monochrome sensor + +Optional Properties: + +- link-frequencies: List of allowed link frequencies in Hz. Each frequency is + expressed as a 64-bit big-endian integer. +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. +- standby-gpios: GPIO handle which is connected to the standby pin of the chip. + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + mt9v032@5c { + compatible = "aptina,mt9v032"; + reg = <0x5c>; + + port { + mt9v032_out: endpoint { + link-frequencies = /bits/ 64 + <13000000 26600000 27000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.yaml b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.yaml new file mode 100644 index 000000000..088022f88 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/aptina,mt9v111.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Aptina MT9V111 CMOS sensor + +maintainers: + - Jacopo Mondi <jacopo@jmondi.org> + +description: | + The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core + based on Aptina MT9V011 sensor and an integrated Image Flow Processor (IFP). + + The sensor has an active pixel array of 640x480 pixels and can output a number + of image resolutions and formats controllable through a simple two-wires + interface. + +properties: + compatible: + const: aptina,mt9v111 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + enable-gpios: + description: Enable signal, pin name "OE#". Active low. + maxItems: 1 + + standby-gpios: + description: | + Low power state control signal, pin name "STANDBY". Active high. + maxItems: 1 + + reset-gpios: + description: Chip reset signal, pin name "RESET#". Active low. + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/properties/port + description: | + Output video port. + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@48 { + compatible = "aptina,mt9v111"; + reg = <0x48>; + clocks = <&camera_clk>; + + port { + mt9v111_out: endpoint { + remote-endpoint = <&ceu_in>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/asahi-kasei,ak7375.yaml b/Documentation/devicetree/bindings/media/i2c/asahi-kasei,ak7375.yaml new file mode 100644 index 000000000..fe312cc6a --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/asahi-kasei,ak7375.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/asahi-kasei,ak7375.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Asahi Kasei Microdevices AK7375 voice coil lens actuator + +maintainers: + - Tianshu Qiu <tian.shu.qiu@intel.com> + +description: + AK7375 is a voice coil motor (VCM) camera lens actuator that + is controlled over I2C. + +properties: + compatible: + enum: + - asahi-kasei,ak7345 + - asahi-kasei,ak7375 + + reg: + maxItems: 1 + + vdd-supply: + description: VDD supply + + vio-supply: + description: I/O pull-up supply + +required: + - compatible + - reg + - vdd-supply + - vio-supply + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ak7375: camera-lens@c { + compatible = "asahi-kasei,ak7375"; + reg = <0x0c>; + + vdd-supply = <&vreg_l23a_2p8>; + vio-supply = <&vreg_lvs1a_1p8>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/chrontel,ch7322.yaml b/Documentation/devicetree/bindings/media/i2c/chrontel,ch7322.yaml new file mode 100644 index 000000000..4e69b6a7f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/chrontel,ch7322.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/chrontel,ch7322.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Chrontel HDMI-CEC Controller + +maintainers: + - Jeff Chase <jnchase@google.com> + +description: + The Chrontel CH7322 is a discrete HDMI-CEC controller. It is + programmable through I2C and drives a single CEC line. + +allOf: + - $ref: /schemas/media/cec/cec-common.yaml# + +properties: + compatible: + const: chrontel,ch7322 + + reg: + description: I2C device address + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + description: + Reference to the GPIO connected to the RESET pin, if any. This + pin is active-low. + maxItems: 1 + + standby-gpios: + description: + Reference to the GPIO connected to the OE pin, if any. When low + the device will respond to power status requests with "standby" + if in auto mode. + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + cec@75 { + compatible = "chrontel,ch7322"; + reg = <0x75>; + interrupts = <47 IRQ_TYPE_EDGE_RISING>; + standby-gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + hdmi-phandle = <&hdmi>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.yaml b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.yaml new file mode 100644 index 000000000..66229a3dc --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/dongwoon,dw9714.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Dongwoon Anatech DW9714 camera voice coil lens driver + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +description: + DW9174 is a 10-bit DAC with current sink capability. It is intended for + driving voice coil lenses in camera modules. + +properties: + compatible: + const: dongwoon,dw9714 + + reg: + maxItems: 1 + + powerdown-gpios: + description: + XSD pin for shutdown (active low) + + vcc-supply: + description: VDD power supply + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera-lens@c { + compatible = "dongwoon,dw9714"; + reg = <0x0c>; + vcc-supply = <®_csi_1v8>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9719.yaml b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9719.yaml new file mode 100644 index 000000000..8e8d62436 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9719.yaml @@ -0,0 +1,89 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/dongwoon,dw9719.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Dongwoon Anatech DW9719 Voice Coil Motor (VCM) Controller + +maintainers: + - André Apitzsch <git@apitzsch.eu> + +description: + The Dongwoon DW9718S/9719/9761 is a single 10-bit digital-to-analog converter + with 100 mA output current sink capability, designed for linear control of + voice coil motors (VCM) in camera lenses. This chip provides a Smart Actuator + Control (SAC) mode intended for driving voice coil lenses in camera modules. + +properties: + compatible: + enum: + - dongwoon,dw9718s + - dongwoon,dw9719 + - dongwoon,dw9761 + - dongwoon,dw9800k + + reg: + maxItems: 1 + + vdd-supply: + description: VDD power supply + + dongwoon,sac-mode: + description: | + Slew Rate Control mode to use: direct, LSC (Linear Slope Control) or + SAC1-SAC6 (Smart Actuator Control). + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # Direct mode + - 1 # LSC mode + - 2 # SAC1 mode (operation time# 0.32 x Tvib) + - 3 # SAC2 mode (operation time# 0.48 x Tvib) + - 4 # SAC3 mode (operation time# 0.72 x Tvib) + - 5 # SAC4 mode (operation time# 1.20 x Tvib) + - 6 # SAC5 mode (operation time# 1.64 x Tvib) + - 7 # SAC6 mode (operation time# 1.88 x Tvib) + default: 4 + + dongwoon,vcm-prescale: + description: + Indication of VCM switching frequency dividing rate select. + $ref: /schemas/types.yaml#/definitions/uint32 + +required: + - compatible + - reg + - vdd-supply + +allOf: + - if: + properties: + compatible: + contains: + const: dongwoon,dw9718s + then: + properties: + dongwoon,vcm-prescale: + description: + The final frequency is 10 MHz divided by (value + 2). + maximum: 15 + default: 0 + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + actuator@c { + compatible = "dongwoon,dw9718s"; + reg = <0x0c>; + + vdd-supply = <&pm8937_l17>; + + dongwoon,sac-mode = <4>; + dongwoon,vcm-prescale = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml new file mode 100644 index 000000000..a0855d3b7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml @@ -0,0 +1,97 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/dongwoon,dw9768.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Dongwoon Anatech DW9768 Voice Coil Motor (VCM) Lens + +maintainers: + - Dongchun Zhu <dongchun.zhu@mediatek.com> + +description: |- + The Dongwoon DW9768 is a single 10-bit digital-to-analog (DAC) converter + with 100 mA output current sink capability. VCM current is controlled with + a linear mode driver. The DAC is controlled via a 2-wire (I2C-compatible) + serial interface that operates at clock rates up to 1MHz. This chip + integrates Advanced Actuator Control (AAC) technology and is intended for + driving voice coil lenses in camera modules. + +properties: + compatible: + enum: + - dongwoon,dw9768 # for DW9768 VCM + - giantec,gt9769 # for GT9769 VCM + + reg: + maxItems: 1 + + vin-supply: + description: + Definition of the regulator used as Digital I/O voltage supply. + + vdd-supply: + description: + Definition of the regulator used as Digital core voltage supply. + + dongwoon,aac-mode: + description: + Indication of AAC mode select. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 1 # AAC2 mode(operation time# 0.48 x Tvib) + - 2 # AAC3 mode(operation time# 0.70 x Tvib) + - 3 # AAC4 mode(operation time# 0.75 x Tvib) + - 5 # AAC8 mode(operation time# 1.13 x Tvib) + default: 2 + + dongwoon,aac-timing: + description: + Number of AAC Timing count that controlled by one 6-bit period of + vibration register AACT[5:0], the unit of which is 100 us. + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0x20 + minimum: 0x00 + maximum: 0x3f + + dongwoon,clock-presc: + description: + Indication of VCM internal clock dividing rate select, as one multiple + factor to calculate VCM ring periodic time Tvib. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # Dividing Rate - 2 + - 1 # Dividing Rate - 1 + - 2 # Dividing Rate - 1/2 + - 3 # Dividing Rate - 1/4 + - 4 # Dividing Rate - 8 + - 5 # Dividing Rate - 4 + default: 1 + +required: + - compatible + - reg + - vin-supply + - vdd-supply + +additionalProperties: false + +examples: + - | + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + dw9768: camera-lens@c { + compatible = "dongwoon,dw9768"; + reg = <0x0c>; + + vin-supply = <&mt6358_vcamio_reg>; + vdd-supply = <&mt6358_vcama2_reg>; + dongwoon,aac-timing = <0x39>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.yaml b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.yaml new file mode 100644 index 000000000..aae246ca3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.yaml @@ -0,0 +1,41 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2018, 2021 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/dongwoon,dw9807-vcm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Dongwoon Anatech DW9807 voice coil lens driver + +maintainers: + - Sakari Ailus <sakari.ailus@linux.intel.com> + +description: | + DW9807 is a 10-bit DAC with current sink capability. It is intended for + controlling voice coil lenses. + +properties: + compatible: + const: dongwoon,dw9807-vcm + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + lens@e { + compatible = "dongwoon,dw9807-vcm"; + reg = <0x0e>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/galaxycore,gc0308.yaml b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc0308.yaml new file mode 100644 index 000000000..2bf1a81fe --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc0308.yaml @@ -0,0 +1,108 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/galaxycore,gc0308.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Galaxycore GC0308 and GC0309 Image Sensors + +maintainers: + - Sebastian Reichel <sre@kernel.org> + +description: | + The GalaxyCore GC0308 (1/6.5") and GC0309 (1/9") are 640x480 VGA sensors + programmable through an I2C interface and connected via parallel bus. + They include an ISP capable of auto exposure and auto white balance. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + oneOf: + - const: galaxycore,gc0308 + - items: + - const: galaxycore,gc0309 + - const: galaxycore,gc0308 + + reg: + const: 0x21 + + clocks: + description: Reference to the xclk clock. + maxItems: 1 + + reset-gpios: + description: GPIO descriptor for the reset pin. + maxItems: 1 + + powerdown-gpios: + description: GPIO descriptor for the powerdown pin. + maxItems: 1 + + vdd28-supply: + description: 2.8V supply + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + description: | + Video output port. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-width: true + data-shift: true + hsync-active: true + vsync-active: true + data-active: true + pclk-sample: true + + required: + - bus-width + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - powerdown-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera-sensor@21 { + compatible = "galaxycore,gc0308"; + reg = <0x21>; + clocks = <&camera_clk>; + powerdown-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + vdd28-supply = <&vdd28>; + + port { + gc0308_ep: endpoint { + remote-endpoint = <¶llel_from_gc0308>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <1>; /* active high */ + vsync-active = <1>; /* active high */ + data-active = <1>; /* active high */ + pclk-sample = <1>; /* sample on rising edge */ + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/galaxycore,gc05a2.yaml b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc05a2.yaml new file mode 100644 index 000000000..0e7a7b5ac --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc05a2.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2023 MediaTek Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/galaxycore,gc05a2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GalaxyCore gc05a2 1/5" 5M Pixel MIPI CSI-2 sensor + +maintainers: + - Zhi Mao <zhi.mao@mediatek.com> + +description: + The gc05a2 is a raw image sensor with an MIPI CSI-2 image data + interface and CCI (I2C compatible) control bus. The output format + is raw Bayer. + +properties: + compatible: + const: galaxycore,gc05a2 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + dovdd-supply: true + + avdd-supply: true + + dvdd-supply: true + + reset-gpios: + description: Reference to the GPIO connected to the RESETB pin. + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + description: + Output port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + - items: + - const: 1 + - const: 2 + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - dovdd-supply + - avdd-supply + - dvdd-supply + - reset-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@37 { + compatible = "galaxycore,gc05a2"; + reg = <0x37>; + + clocks = <&gc05a2_clk>; + + reset-gpios = <&pio 21 GPIO_ACTIVE_LOW>; + + avdd-supply = <&gc05a2_avdd>; + dovdd-supply = <&gc05a2_dovdd>; + dvdd-supply = <&gc05a2_dvdd>; + + port { + sensor_out: endpoint { + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <448000000 224000000>; + remote-endpoint = <&seninf_csi_port_1_in>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/galaxycore,gc08a3.yaml b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc08a3.yaml new file mode 100644 index 000000000..51b8ece09 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc08a3.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2023 MediaTek Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/galaxycore,gc08a3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GalaxyCore gc08a3 1/4" 8M Pixel MIPI CSI-2 sensor + +maintainers: + - Zhi Mao <zhi.mao@mediatek.com> + +description: + The gc08a3 is a raw image sensor with an MIPI CSI-2 image data + interface and CCI (I2C compatible) control bus. The output format + is raw Bayer. + +properties: + compatible: + const: galaxycore,gc08a3 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + dovdd-supply: true + + avdd-supply: true + + dvdd-supply: true + + reset-gpios: + description: Reference to the GPIO connected to the RESETB pin. + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + description: + Output port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + - items: + - const: 1 + - const: 2 + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - dovdd-supply + - avdd-supply + - dvdd-supply + - reset-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@31 { + compatible = "galaxycore,gc08a3"; + reg = <0x31>; + + clocks = <&gc08a3_clk>; + + reset-gpios = <&pio 19 GPIO_ACTIVE_LOW>; + + avdd-supply = <&gc08a3_avdd>; + dovdd-supply = <&gc08a3_dovdd>; + dvdd-supply = <&gc08a3_dvdd>; + + port { + sensor_out: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <336000000 207000000>; + remote-endpoint = <&seninf_csi_port_0_in>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/galaxycore,gc2145.yaml b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc2145.yaml new file mode 100644 index 000000000..9eac588de --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc2145.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/galaxycore,gc2145.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Galaxy Core 1/5'' UXGA CMOS Image Sensor + +maintainers: + - Alain Volmat <alain.volmat@foss.st.com> + +description: + The Galaxy Core GC2145 is a 2 Megapixel CMOS image sensor, for mobile + phone camera applications and digital camera products. GC2145 incorporates a + 1616V x 1232H active pixel array, on-chip 10-bit ADC, and image signal + processor allowing AE/AWB/interpolation/de-noise/color-conversion and + gamma correction. Bayer RGB, RGB565 and YCbCr 4:2:2 can be provided by the + sensor. It is programmable through an I2C interface. Image data is sent + either through a parallel interface or through MIPI CSI-2. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: galaxycore,gc2145 + + reg: + const: 0x3c + + clocks: + maxItems: 1 + + powerdown-gpios: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + iovdd-supply: + description: Power Supply for I/O circuits (1.7 - 3V). + + avdd-supply: + description: Power for analog circuit/sensor array (2.7 - 3V). + + dvdd-supply: + description: Power for digital core (1.7 - 1.9V). + + orientation: true + + rotation: true + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + + required: + - link-frequencies + + required: + - endpoint + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - powerdown-gpios + - reset-gpios + - iovdd-supply + - avdd-supply + - dvdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "galaxycore,gc2145"; + reg = <0x3c>; + clocks = <&clk_ext_camera>; + iovdd-supply = <&scmi_v3v3_sw>; + avdd-supply = <&scmi_v3v3_sw>; + dvdd-supply = <&scmi_v3v3_sw>; + powerdown-gpios = <&mcp23017 3 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; + reset-gpios = <&mcp23017 4 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; + + port { + endpoint { + remote-endpoint = <&mipid02_0>; + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <120000000 192000000 240000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml new file mode 100644 index 000000000..1a57f2aa1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml @@ -0,0 +1,119 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor + +maintainers: + - Martin Kepplinger <martin.kepplinger@puri.sm> + +description: |- + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data + interface and CCI (I2C compatible) control bus. The output format + is raw Bayer. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: hynix,hi846 + + reg: + maxItems: 1 + + clocks: + items: + - description: Reference to the mclk clock. + + reset-gpios: + description: Reference to the GPIO connected to the RESETB pin. Active low. + maxItems: 1 + + shutdown-gpios: + description: Reference to the GPIO connected to the XSHUTDOWN pin. Active low. + maxItems: 1 + + vddio-supply: + description: Definition of the regulator used for the VDDIO power supply. + + vdda-supply: + description: Definition of the regulator used for the VDDA power supply. + + vddd-supply: + description: Definition of the regulator used for the VDDD power supply. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + - items: + - const: 1 + - const: 2 + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - vddio-supply + - vdda-supply + - vddd-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hi846: camera@20 { + compatible = "hynix,hi846"; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_csi1>; + clocks = <&clk 0>; + vdda-supply = <®_camera_vdda>; + vddd-supply = <®_camera_vddd>; + vddio-supply = <®_camera_vddio>; + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; + shutdown-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>; + orientation = <0>; + rotation = <0>; + + port { + camera_out: endpoint { + remote-endpoint = <&csi1_ep1>; + link-frequencies = /bits/ 64 + <80000000 200000000>; + data-lanes = <1 2>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/imi,rdacm2x-gmsl.yaml b/Documentation/devicetree/bindings/media/i2c/imi,rdacm2x-gmsl.yaml new file mode 100644 index 000000000..e57575c44 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/imi,rdacm2x-gmsl.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause +# Copyright (C) 2019 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/imi,rdacm2x-gmsl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: IMI D&D RDACM20 and RDACM21 Automotive Camera Platforms + +maintainers: + - Jacopo Mondi <jacopo+renesas@jmondi.org> + - Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> + - Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> + +description: -| + The IMI D&D RDACM20 and RDACM21 are GMSL-compatible camera designed for + automotive applications. + + The RDACM20 camera module encloses a Maxim Integrated MAX9271 GMSL serializer, + coupled with an OV10635 image sensor and an embedded MCU. Both the MCU and + the image sensor are connected to the serializer local I2C bus and are + accessible by the host SoC by direct addressing. + + The RDACM21 camera module encloses the same serializer, coupled with an + OV10640 image sensor and an OV490 ISP. Only the OV490 ISP is interfaced to + the serializer local I2C bus while the image sensor is not accessible from + the host SoC. + + They both connect to a remote GMSL endpoint through a coaxial cable. + + IMI RDACM20 + +---------------+ +--------------------------------+ + | GMSL | <- Video Stream | <- Video--------\ | + | |< === GMSL Link ====== >|MAX9271<- I2C bus-> <-->OV10635 | + | de-serializer | <- I2C messages -> | \<-->MCU | + +---------------+ +--------------------------------+ + + IMI RDACM21 + +---------------+ +--------------------------------+ + | GMSL | <- Video Stream | <- Video--------\ | + | |< === GMSL Link ====== >|MAX9271<- I2C bus-> <-->OV490 | + | | <- I2C messages -> | | | + | de-serializer | | OV10640 <-------| | + +---------------+ +--------------------------------+ + + Both camera modules serialize video data generated by the embedded camera + sensor on the GMSL serial channel to a remote GMSL de-serializer. They also + receive and transmit I2C messages encapsulated and transmitted on the GMSL + bidirectional control channel. + + All I2C traffic received on the GMSL link not directed to the serializer is + propagated on the local I2C bus to the remote device there connected. All the + I2C traffic generated on the local I2C bus not directed to the serializer is + propagated to the remote de-serializer encapsulated in the GMSL control + channel. + + The RDACM20 and RDACM21 DT node should be a direct child of the GMSL + deserializer's I2C bus corresponding to the GMSL link that the camera is + attached to. + +properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + compatible: + enum: + - imi,rdacm20 + - imi,rdacm21 + + reg: + description: -| + I2C device addresses, the first to be assigned to the serializer, the + following ones to be assigned to the remote devices. + + For RDACM20 the second entry of the property is assigned to the + OV10635 image sensor and the optional third one to the embedded MCU. + + For RDACM21 the second entry is assigned to the OV490 ISP and the optional + third one ignored. + + minItems: 2 + maxItems: 3 + + port: + $ref: /schemas/graph.yaml#/properties/port + description: + Connection to the remote GMSL endpoint. + +required: + - compatible + - reg + - port + +additionalProperties: false + +examples: + - | + i2c@e66d8000 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0 0xe66d8000>; + + camera@31 { + compatible = "imi,rdacm20"; + reg = <0x31>, <0x41>, <0x51>; + + port { + rdacm20_out0: endpoint { + remote-endpoint = <&max9286_in0>; + }; + }; + }; + }; + + - | + i2c@e66d8000 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0 0xe66d8000>; + + camera@31 { + compatible = "imi,rdacm21"; + reg = <0x31>, <0x41>; + + port { + rdacm21_out0: endpoint { + remote-endpoint = <&max9286_in0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/isil,isl79987.yaml b/Documentation/devicetree/bindings/media/i2c/isil,isl79987.yaml new file mode 100644 index 000000000..034a6e346 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/isil,isl79987.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/isil,isl79987.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Intersil ISL79987 Analog to MIPI CSI-2 decoder + +maintainers: + - Michael Tretter <m.tretter@pengutronix.de> + - Marek Vasut <marex@denx.de> + +description: + The Intersil ISL79987 is an analog to MIPI CSI-2 decoder which is capable of + receiving up to four analog stream and multiplexing them into up to four MIPI + CSI-2 virtual channels, using one MIPI clock lane and 1/2 data lanes. + +properties: + compatible: + enum: + - isil,isl79987 + + reg: + maxItems: 1 + + reset-gpios: + maxItems: 1 + description: + A GPIO spec for the RSTB pin (active high) + + powerdown-gpios: + maxItems: 1 + description: + A GPIO spec for the Power Down pin (active high) + + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: Output port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 2 + + required: + - data-lanes + + patternProperties: + "^port@[1-4]$": + $ref: /schemas/graph.yaml#/properties/port + description: Input ports + + required: + - port@0 + +additionalProperties: false + +required: + - compatible + - reg + - ports + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + isl7998x_mipi@44 { + compatible = "isil,isl79987"; + reg = <0x44>; + powerdown-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + isl79987_out: endpoint { + remote-endpoint = <&mipi_csi2_in>; + data-lanes = <1 2>; + }; + }; + + port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&camera_0>; + }; + }; + + port@2 { + reg = <2>; + endpoint { + remote-endpoint = <&camera_1>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max2175.txt b/Documentation/devicetree/bindings/media/i2c/maxim,max2175.txt new file mode 100644 index 000000000..02b4e9cd7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max2175.txt @@ -0,0 +1,59 @@ +Maxim Integrated MAX2175 RF to Bits tuner +----------------------------------------- + +The MAX2175 IC is an advanced analog/digital hybrid-radio receiver with +RF to Bits® front-end designed for software-defined radio solutions. + +Required properties: +-------------------- +- compatible: "maxim,max2175" for MAX2175 RF-to-bits tuner. +- clocks: clock specifier. +- port: child port node corresponding to the I2S output, in accordance with + the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The port + node must contain at least one endpoint. + +Optional properties: +-------------------- +- maxim,master : phandle to the master tuner if it is a slave. This + is used to define two tuners in diversity mode + (1 master, 1 slave). By default each tuner is an + individual master. +- maxim,refout-load : load capacitance value (in picofarads) on reference + output drive level. The possible load values are: + 0 (default - refout disabled) + 10 + 20 + 30 + 40 + 60 + 70 +- maxim,am-hiz-filter : empty property indicates the AM Hi-Z filter is used + in this hardware for AM antenna input. + +Example: +-------- + +Board specific DTS file + +/* Fixed XTAL clock node */ +maxim_xtal: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <36864000>; +}; + +/* A tuner device instance under i2c bus */ +max2175_0: tuner@60 { + compatible = "maxim,max2175"; + reg = <0x60>; + clocks = <&maxim_xtal>; + maxim,refout-load = <10>; + + port { + max2175_0_ep: endpoint { + remote-endpoint = <&slave_rx_device>; + }; + }; + +}; diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml new file mode 100644 index 000000000..a37447256 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml @@ -0,0 +1,416 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2019 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/maxim,max9286.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim Integrated Quad GMSL Deserializer + +maintainers: + - Jacopo Mondi <jacopo+renesas@jmondi.org> + - Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> + - Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> + +description: | + The MAX9286 deserializer receives video data on up to 4 Gigabit Multimedia + Serial Links (GMSL) and outputs them on a CSI-2 D-PHY port using up to 4 data + lanes. + + In addition to video data, the GMSL links carry a bidirectional control + channel that encapsulates I2C messages. The MAX9286 forwards all I2C traffic + not addressed to itself to the other side of the links, where a GMSL + serializer will output it on a local I2C bus. In the other direction all I2C + traffic received over GMSL by the MAX9286 is output on the local I2C bus. + +properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + compatible: + const: maxim,max9286 + + reg: + description: I2C device address + maxItems: 1 + + poc-supply: + description: Regulator providing Power over Coax to all the ports + + enable-gpios: + description: GPIO connected to the \#PWDN pin with inverted polarity + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + + maxim,bus-width: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 24, 27, 32 ] + description: | + The GMSL serial data bus width. This setting is normally controlled by + the BWS pin, but may be overridden with this property. The value must + match the configuration of the remote serializers. + + maxim,i2c-remote-bus-hz: + enum: [ 8470, 28300, 84700, 105000, 173000, 339000, 533000, 837000 ] + default: 105000 + description: | + The I2C clock frequency for the remote I2C buses. The value must match + the configuration of the remote serializers. + + maxim,reverse-channel-microvolt: + minimum: 30000 + maximum: 200000 + default: 170000 + description: | + Initial amplitude of the reverse control channel, in micro volts. + + The initial amplitude shall be adjusted to a value compatible with the + configuration of the connected remote serializer. + + Some camera modules (for example RDACM20) include an on-board MCU that + pre-programs the embedded serializer with power supply noise immunity + (high-threshold) enabled. A typical value of the deserializer's reverse + channel amplitude to communicate with pre-programmed serializers is + 170000 micro volts. + + A typical value for the reverse channel amplitude to communicate with + a remote serializer whose high-threshold noise immunity is not enabled + is 100000 micro volts + + maxim,gpio-poc: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + description: | + Index of the MAX9286 gpio output line (0 or 1) that controls Power over + Coax to the cameras and its associated polarity flag. + + The property accepts an array of two unsigned integers, the first being + the gpio line index (0 or 1) and the second being the gpio line polarity + flag (GPIO_ACTIVE_HIGH or GPIO_ACTIVE_LOW) as defined in + <include/dt-bindings/gpio/gpio.h>. + + When the remote cameras power is controlled by one of the MAX9286 gpio + lines, this property has to be used to specify which line among the two + available ones controls the remote camera power enablement. + + When this property is used it is not possible to register a gpio + controller as the gpio lines are controlled directly by the MAX9286 and + not available for consumers, nor the 'poc-supply' property should be + specified. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 0 + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 1 + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 2 + + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 3 + + port@4: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 Output + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: true + + required: + - data-lanes + + required: + - port@4 + + i2c-mux: + type: object + $ref: /schemas/i2c/i2c-mux.yaml# + unevaluatedProperties: false + description: | + Each GMSL link is modelled as a child bus of an i2c bus multiplexer/switch. + + patternProperties: + "^i2c@[0-3]$": + type: object + additionalProperties: false + description: | + Child node of the i2c bus multiplexer which represents a GMSL link. + Each serializer device on the GMSL link remote end is represented with + an i2c-mux child node. The MAX9286 chip supports up to 4 GMSL + channels. + + properties: + reg: + description: The index of the GMSL channel. + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + patternProperties: + "^camera@[a-f0-9]+$": + type: object + description: | + The remote camera device, composed by a GMSL serializer and a + connected video source. + + properties: + compatible: + description: The remote device compatible string. + + reg: + minItems: 2 + maxItems: 3 + description: | + The I2C addresses to be assigned to the remote devices through + address reprogramming. The number of entries depends on the + requirements of the currently connected remote device. + + port: + $ref: /schemas/graph.yaml#/properties/port + description: Connection to the MAX9286 sink. + + required: + - compatible + - reg + - port + + additionalProperties: false + +patternProperties: + "^port[0-3]-poc-supply$": + description: Regulator providing Power over Coax for a particular port + +required: + - compatible + - reg + - ports + - i2c-mux + +allOf: + # Only one way of specifying power supplies is allowed: 'maxim,gpio-poc', + # 'poc-supply' or per-port poc-supply. Additionally, if 'maxim,gpio-poc' is + # present, then 'gpio-controller' isn't allowed. + - if: + required: + - maxim,gpio-poc + then: + properties: + poc-supply: false + gpio-controller: false + patternProperties: + "^port[0-3]-poc-supply$": false + + - if: + required: + - poc-supply + then: + patternProperties: + "^port[0-3]-poc-supply$": false + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c@e66d8000 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0 0xe66d8000>; + + gmsl-deserializer@2c { + compatible = "maxim,max9286"; + reg = <0x2c>; + poc-supply = <&camera_poc_12v>; + enable-gpios = <&gpio 13 GPIO_ACTIVE_HIGH>; + + gpio-controller; + #gpio-cells = <2>; + + maxim,i2c-remote-bus-hz = <339000>; + maxim,reverse-channel-microvolt = <170000>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + max9286_in0: endpoint { + remote-endpoint = <&rdacm20_out0>; + }; + }; + + port@1 { + reg = <1>; + + max9286_in1: endpoint { + remote-endpoint = <&rdacm20_out1>; + }; + }; + + port@2 { + reg = <2>; + + max9286_in2: endpoint { + remote-endpoint = <&rdacm20_out2>; + }; + }; + + port@3 { + reg = <3>; + + max9286_in3: endpoint { + remote-endpoint = <&rdacm20_out3>; + }; + }; + + port@4 { + reg = <4>; + + max9286_out: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + }; + + i2c-mux { + #address-cells = <1>; + #size-cells = <0>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + camera@51 { + compatible = "imi,rdacm20"; + reg = <0x51>, <0x61>; + + port { + rdacm20_out0: endpoint { + remote-endpoint = <&max9286_in0>; + }; + }; + + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + camera@52 { + compatible = "imi,rdacm20"; + reg = <0x52>, <0x62>; + + port { + rdacm20_out1: endpoint { + remote-endpoint = <&max9286_in1>; + }; + }; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + camera@53 { + compatible = "imi,rdacm20"; + reg = <0x53>, <0x63>; + + port { + rdacm20_out2: endpoint { + remote-endpoint = <&max9286_in2>; + }; + }; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + camera@54 { + compatible = "imi,rdacm20"; + reg = <0x54>, <0x64>; + + port { + rdacm20_out3: endpoint { + remote-endpoint = <&max9286_in3>; + }; + }; + }; + }; + }; + }; + + /* + * Example of a deserializer that controls the camera Power over Coax + * through one of its gpio lines. + */ + gmsl-deserializer@6c { + compatible = "maxim,max9286"; + reg = <0x6c>; + enable-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; + + /* + * The remote camera power is controlled by MAX9286 GPIO line #0. + * No 'poc-supply' nor 'gpio-controller' are specified. + */ + maxim,gpio-poc = <0 GPIO_ACTIVE_LOW>; + + /* + * Do not describe connections as they're the same as in the previous + * example. + */ + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@4 { + reg = <4>; + }; + }; + + i2c-mux { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max96712.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max96712.yaml new file mode 100644 index 000000000..26f85151a --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max96712.yaml @@ -0,0 +1,121 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2021 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/maxim,max96712.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Quad GMSL2 to CSI-2 Deserializer with GMSL1 Compatibility + +maintainers: + - Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> + +description: | + The MAX96712 deserializer converts GMSL2 or GMSL1 serial inputs into MIPI + CSI-2 D-PHY or C-PHY formatted outputs. The device allows each link to + simultaneously transmit bidirectional control-channel data while forward + video transmissions are in progress. The MAX96712 can accommodate as many as + four remotely located sensors using industry-standard coax or STP + interconnects. + + Each GMSL2 serial link operates at a fixed rate of 3Gbps or 6Gbps in the + forward direction and 187.5Mbps in the reverse direction. In GMSL1 mode, the + MAX96712 can be paired with first-generation 3.12Gbps or 1.5Gbps GMSL1 + serializers or operate up to 3.12Gbps with GMSL2 serializers in GMSL1 mode. + +properties: + compatible: + items: + - enum: + - maxim,max96712 + - maxim,max96724 + + reg: + description: I2C device address + maxItems: 1 + + enable-gpios: true + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 0 + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 1 + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 2 + + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: GMSL Input 3 + + port@4: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 Output + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: true + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + - bus-type + + required: + - port@4 + +required: + - compatible + - reg + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c@e6508000 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0 0xe6508000>; + + gmsl0: gmsl-deserializer@49 { + compatible = "maxim,max96712"; + reg = <0x49>; + enable-gpios = <&pca9654_a 0 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@4 { + reg = <4>; + max96712_out0: endpoint { + bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>; + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max96714.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max96714.yaml new file mode 100644 index 000000000..3ace50e11 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max96714.yaml @@ -0,0 +1,174 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2024 Collabora Ltd. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/maxim,max96714.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim MAX96714 GMSL2 to CSI-2 Deserializer + +maintainers: + - Julien Massot <julien.massot@collabora.com> + +description: + The MAX96714 deserializer converts GMSL2 serial inputs into MIPI + CSI-2 D-PHY formatted output. The device allows the GMSL2 link to + simultaneously transmit bidirectional control-channel data while forward + video transmissions are in progress. The MAX96714 can connect to one + remotely located serializer using industry-standard coax or STP + interconnects. The device cans operate in pixel or tunnel mode. In pixel mode + the MAX96714 can select individual video stream, while the tunnel mode forward all + the MIPI data received by the serializer. + + The GMSL2 serial link operates at a fixed rate of 3Gbps or 6Gbps in the + forward direction and 187.5Mbps in the reverse direction. + MAX96714F only supports a fixed rate of 3Gbps in the forward direction. + +properties: + compatible: + oneOf: + - const: maxim,max96714f + - items: + - enum: + - maxim,max96714 + - const: maxim,max96714f + + reg: + maxItems: 1 + + powerdown-gpios: + maxItems: 1 + description: + Specifier for the GPIO connected to the PWDNB pin. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + unevaluatedProperties: false + description: GMSL Input + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + description: + Endpoint for GMSL2-Link port. + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 Output port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + lane-polarities: + minItems: 1 + maxItems: 5 + + link-frequencies: + maxItems: 1 + + required: + - data-lanes + + required: + - port@1 + + i2c-gate: + $ref: /schemas/i2c/i2c-gate.yaml + unevaluatedProperties: false + description: + The MAX96714 will pass through and forward the I2C requests from the + incoming I2C bus over the GMSL2 link. Therefore it supports an i2c-gate + subnode to configure a serializer. + + port0-poc-supply: + description: Regulator providing Power over Coax for the GMSL port + +required: + - compatible + - reg + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + deserializer@28 { + compatible = "maxim,max96714f"; + reg = <0x28>; + powerdown-gpios = <&main_gpio0 37 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + max96714_gmsl_in: endpoint { + remote-endpoint = <&max96917f_gmsl_out>; + }; + }; + + port@1 { + reg = <1>; + max96714_csi_out: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <400000000>; + remote-endpoint = <&csi_in>; + }; + }; + }; + + i2c-gate { + #address-cells = <1>; + #size-cells = <0>; + + serializer@40 { + compatible = "maxim,max96717f"; + reg = <0x40>; + gpio-controller; + #gpio-cells = <2>; + #clock-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + max96717f_csi_in: endpoint { + data-lanes = <1 2>; + lane-polarities = <1 0 1>; + remote-endpoint = <&sensor_out>; + }; + }; + + port@1 { + reg = <1>; + max96917f_gmsl_out: endpoint { + remote-endpoint = <&max96714_gmsl_in>; + }; + }; + }; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max96717.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max96717.yaml new file mode 100644 index 000000000..d1e8ba6e3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max96717.yaml @@ -0,0 +1,157 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2024 Collabora Ltd. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/maxim,max96717.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MAX96717 CSI-2 to GMSL2 Serializer + +maintainers: + - Julien Massot <julien.massot@collabora.com> + +description: + The MAX96717 serializer converts MIPI CSI-2 D-PHY formatted input + into GMSL2 serial outputs. The device allows the GMSL2 link to + simultaneously transmit bidirectional control-channel data while forward + video transmissions are in progress. The MAX96717 can connect to one + remotely located deserializer using industry-standard coax or STP + interconnects. The device cans operate in pixel or tunnel mode. In pixel mode + the MAX96717 can select the MIPI datatype, while the tunnel mode forward all the MIPI + data received by the serializer. + The MAX96717 supports Reference Over Reverse (channel), + to generate a clock output for the sensor from the GMSL reverse channel. + + The GMSL2 serial link operates at a fixed rate of 3Gbps or 6Gbps in the + forward direction and 187.5Mbps in the reverse direction. + MAX96717F only supports a fixed rate of 3Gbps in the forward direction. + +properties: + compatible: + oneOf: + - const: maxim,max96717f + - items: + - enum: + - maxim,max96717 + - const: maxim,max96717f + + '#gpio-cells': + const: 2 + description: + First cell is the GPIO pin number, second cell is the flags. The GPIO pin + number must be in range of [0, 10]. + + gpio-controller: true + + '#clock-cells': + const: 0 + + reg: + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 Input port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + lane-polarities: + minItems: 1 + maxItems: 5 + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/properties/port + unevaluatedProperties: false + description: GMSL Output port + + required: + - port@1 + + i2c-gate: + $ref: /schemas/i2c/i2c-gate.yaml + unevaluatedProperties: false + description: + The MAX96717 will forward the I2C requests from the + incoming GMSL2 link. Therefore, it supports an i2c-gate + subnode to configure a sensor. + +required: + - compatible + - reg + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + serializer: serializer@40 { + compatible = "maxim,max96717f"; + reg = <0x40>; + gpio-controller; + #gpio-cells = <2>; + #clock-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + max96717f_csi_in: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&sensor_out>; + }; + }; + + port@1 { + reg = <1>; + max96917f_gmsl_out: endpoint { + remote-endpoint = <&deser_gmsl_in>; + }; + }; + }; + + i2c-gate { + #address-cells = <1>; + #size-cells = <0>; + sensor@10 { + compatible = "st,st-vgxy61"; + reg = <0x10>; + reset-gpios = <&serializer 0 GPIO_ACTIVE_LOW>; + clocks = <&serializer>; + VCORE-supply = <&v1v2>; + VDDIO-supply = <&v1v8>; + VANA-supply = <&v2v8>; + port { + sensor_out: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&max96717f_csi_in>; + }; + }; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt b/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt new file mode 100644 index 000000000..060d2b7a5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt @@ -0,0 +1,20 @@ +* Melexis MLX90640 FIR Sensor + +Melexis MLX90640 FIR sensor support which allows recording of thermal data +with 32x24 resolution excluding 2 lines of coefficient data that is used by +userspace to render processed frames. + +Required Properties: + - compatible : Must be "melexis,mlx90640" + - reg : i2c address of the device + +Example: + + i2c0@1c22000 { + ... + mlx90640@33 { + compatible = "melexis,mlx90640"; + reg = <0x33>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/micron,mt9m111.txt b/Documentation/devicetree/bindings/media/i2c/micron,mt9m111.txt new file mode 100644 index 000000000..d0bed6fa9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/micron,mt9m111.txt @@ -0,0 +1,37 @@ +Micron 1.3Mp CMOS Digital Image Sensor + +The Micron MT9M111 is a CMOS active pixel digital image sensor with an active +array size of 1280H x 1024V. It is programmable through a simple two-wire serial +interface. + +Required Properties: +- compatible: value should be "micron,mt9m111" +- clocks: reference to the master clock. +- clock-names: shall be "mclk". + +The device node must contain one 'port' child node with one 'endpoint' child +sub-node for its digital output video port, in accordance with the video +interface bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt + +Optional endpoint properties: +- pclk-sample: For information see ../video-interfaces.txt. The value is set to + 0 if it isn't specified. + +Example: + + i2c_master { + mt9m111@5d { + compatible = "micron,mt9m111"; + reg = <0x5d>; + clocks = <&mclk>; + clock-names = "mclk"; + + port { + mt9m111_1: endpoint { + remote-endpoint = <&pxa_camera>; + pclk-sample = <1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mipi-ccs.yaml b/Documentation/devicetree/bindings/media/i2c/mipi-ccs.yaml new file mode 100644 index 000000000..217b08c8c --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mipi-ccs.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2014--2020 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/mipi-ccs.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MIPI CCS, SMIA++ and SMIA compliant camera sensors + +maintainers: + - Sakari Ailus <sakari.ailus@linux.intel.com> + +description: + + CCS (Camera Command Set) is a raw Bayer camera sensor standard defined by the + MIPI Alliance; see + <URL:https://www.mipi.org/specifications/camera-command-set>. + + SMIA (Standard Mobile Imaging Architecture) is an image sensor standard + defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension of + that. + + More detailed documentation can be found in + Documentation/devicetree/bindings/media/video-interfaces.txt . + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + oneOf: + - items: + - const: mipi-ccs-1.1 + - const: mipi-ccs + - items: + - const: mipi-ccs-1.0 + - const: mipi-ccs + - const: nokia,smia + + reg: + maxItems: 1 + + vana-supply: + description: Analogue voltage supply (VANA), sensor dependent. + + vcore-supply: + description: Core voltage supply (VCore), sensor dependent. + + vio-supply: + description: I/O voltage supply (VIO), sensor dependent. + + clocks: + description: External clock to the sensor. + maxItems: 1 + + clock-frequency: + description: Frequency of the external clock to the sensor in Hz. + deprecated: true + + reset-gpios: + description: Reset GPIO. Also commonly called XSHUTDOWN in hardware + documentation. + maxItems: 1 + + flash-leds: true + lens-focus: true + + rotation: + enum: [ 0, 180 ] + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + data-lanes: true + bus-type: + enum: + - 1 # CSI-2 C-PHY + - 3 # CCP2 + - 4 # CSI-2 D-PHY + + required: + - link-frequencies + - data-lanes + - bus-type + +required: + - compatible + - reg + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + clock-frequency = <400000>; + + camera-sensor@10 { + compatible = "mipi-ccs-1.0", "mipi-ccs"; + reg = <0x10>; + reset-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>; + vana-supply = <&vaux3>; + + clocks = <&omap3_isp 0>; + assigned-clocks = <&omap3_isp 0>; + assigned-clock-rates = <9600000>; + + port { + ccs_ep: endpoint { + data-lanes = <1 2>; + remote-endpoint = <&csi2a_ep>; + link-frequencies = /bits/ 64 <199200000 210000000 + 499200000>; + bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/nxp,tda19971.yaml b/Documentation/devicetree/bindings/media/i2c/nxp,tda19971.yaml new file mode 100644 index 000000000..477e59316 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/nxp,tda19971.yaml @@ -0,0 +1,162 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/nxp,tda19971.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP TDA1997x HDMI receiver + +maintainers: + - Frank Li <Frank.Li@nxp.com> + +description: | + The TDA19971/73 are HDMI video receivers. + + The TDA19971 Video port output pins can be used as follows: + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4] + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4] + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4] + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2] + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0] + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles) + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles) + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) + + The TDA19973 Video port output pins can be used as follows: + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0] + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0] + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0] + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) + + The Video port output pins are mapped via 4-bit 'pin groups' allowing + for a variety of connection possibilities including swapping pin order within + pin groups. The video_portcfg device-tree property consists of register mapping + pairs which map a chip-specific VP output register to a 4-bit pin group. If + the pin group needs to be bit-swapped you can use the *_S pin-group defines. + +properties: + compatible: + enum: + - nxp,tda19971 + - nxp,tda19973 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + DOVDD-supply: true + + DVDD-supply: true + + AVDD-supply: true + + '#sound-dai-cells': + const: 0 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + nxp,vidout-portcfg: + $ref: /schemas/types.yaml#/definitions/uint32-matrix + minItems: 1 + maxItems: 4 + items: + items: + - description: Video Port control registers index. + maximum: 8 + minimum: 0 + - description: pin(pinswapped) groups + + description: + array of pairs mapping VP output pins to pin groups. + + nxp,audout-format: + enum: + - i2s + - spdif + + nxp,audout-width: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [8, 16, 24, 32] + description: + width of audio output data bus. + + nxp,audout-layout: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: + data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used). + + nxp,audout-mclk-fs: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Multiplication factor between stream rate and codec mclk. + +required: + - compatible + - reg + - interrupts + - DOVDD-supply + - AVDD-supply + - DVDD-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/media/tda1997x.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hdmi-receiver@48 { + compatible = "nxp,tda19971"; + reg = <0x48>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tda1997x>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + DOVDD-supply = <®_3p3v>; + AVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p8v>; + /* audio */ + #sound-dai-cells = <0>; + nxp,audout-format = "i2s"; + nxp,audout-layout = <0>; + nxp,audout-width = <16>; + nxp,audout-mclk-fs = <128>; + /* + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4] + * and Y[11:4] across 16bits in the same pixclk cycle. + */ + nxp,vidout-portcfg = + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >, + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >, + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */ + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >, + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */ + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >; + + port { + endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <16>; + hsync-active = <1>; + vsync-active = <1>; + data-active = <1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/onnn,ar0521.yaml b/Documentation/devicetree/bindings/media/i2c/onnn,ar0521.yaml new file mode 100644 index 000000000..b617cc5c6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/onnn,ar0521.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/onnn,ar0521.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ON Semiconductor AR0521 MIPI CSI-2 sensor + +maintainers: + - Krzysztof Hałasa <khalasa@piap.pl> + +description: |- + The AR0521 is a raw CMOS image sensor with MIPI CSI-2 and + I2C-compatible control interface. + +properties: + compatible: + const: onnn,ar0521 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: extclk + + vaa-supply: + description: + Definition of the regulator used as analog (2.7 V) voltage supply. + + vdd-supply: + description: + Definition of the regulator used as digital core (1.2 V) voltage supply. + + vdd_io-supply: + description: + Definition of the regulator used as digital I/O (1.8 V) voltage supply. + + reset-gpios: + description: reset GPIO, usually active low + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: | + Video output port. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + const: 4 + data-lanes: + anyOf: + - items: + - const: 1 + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + +required: + - compatible + - reg + - clocks + - clock-names + - vaa-supply + - vdd-supply + - vdd_io-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/imx6qdl-clock.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ar0521: camera-sensor@36 { + compatible = "onnn,ar0521"; + reg = <0x36>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mipi_camera>; + clocks = <&clks IMX6QDL_CLK_CKO>; + clock-names = "extclk"; + reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + vaa-supply = <®_2p7v>; + vdd-supply = <®_1p2v>; + vdd_io-supply = <®_1p8v>; + + port { + mipi_camera_to_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_in>; + data-lanes = <1 2 3 4>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/onnn,mt9m001.txt b/Documentation/devicetree/bindings/media/i2c/onnn,mt9m001.txt new file mode 100644 index 000000000..c920552b0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/onnn,mt9m001.txt @@ -0,0 +1,38 @@ +MT9M001: 1/2-Inch Megapixel Digital Image Sensor + +The MT9M001 is an SXGA-format with a 1/2-inch CMOS active-pixel digital +image sensor. It is programmable through I2C interface. + +Required Properties: + +- compatible: shall be "onnn,mt9m001". +- clocks: reference to the master clock into sensor + +Optional Properties: + +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. + Active low. +- standby-gpios: GPIO handle which is connected to the standby pin of the chip. + Active high. + +The device node must contain one 'port' child node with one 'endpoint' child +sub-node for its digital output video port, in accordance with the video +interface bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + &i2c1 { + camera-sensor@5d { + compatible = "onnn,mt9m001"; + reg = <0x5d>; + reset-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; + standby-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + clocks = <&camera_clk>; + port { + mt9m001_out: endpoint { + remote-endpoint = <&vcap_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/onnn,mt9m114.yaml b/Documentation/devicetree/bindings/media/i2c/onnn,mt9m114.yaml new file mode 100644 index 000000000..2b39614f5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/onnn,mt9m114.yaml @@ -0,0 +1,128 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/onnn,mt9m114.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: onsemi 1/6-inch 720p CMOS Digital Image Sensor + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: |- + The onsemi MT9M114 is a 1/6-inch 720p (1.26 Mp) CMOS digital image sensor + with an active pixel-array size of 1296H x 976V. It is programmable through + an I2C interface and outputs image data over a 8-bit parallel or 1-lane MIPI + CSI-2 connection. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + enum: + - onnn,mt9m114 + - aptina,mi1040 + + reg: + description: I2C device address + enum: + - 0x48 + - 0x5d + + clocks: + description: EXTCLK clock signal + maxItems: 1 + + vdd-supply: + description: + Core digital voltage supply, 1.8V + + vddio-supply: + description: + I/O digital voltage supply, 1.8V or 2.8V + + vaa-supply: + description: + Analog voltage supply, 2.8V + + reset-gpios: + description: |- + Reference to the GPIO connected to the RESET_BAR pin, if any (active + low). + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + additionalProperties: false + + properties: + bus-type: + enum: [4, 5, 6] + + link-frequencies: true + remote-endpoint: true + + # The number and mapping of lanes (for CSI-2), and the bus width and + # signal polarities (for parallel and BT.656) are fixed and must not + # be specified. + + required: + - bus-type + - link-frequencies + + slew-rate: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Slew rate ot the output pads DOUT[7:0], LINE_VALID, FRAME_VALID and + PIXCLK. Higher values imply steeper voltage-flanks on the pads. + minimum: 0 + maximum: 7 + default: 7 + +required: + - compatible + - reg + - clocks + - vdd-supply + - vddio-supply + - vaa-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@48 { + compatible = "onnn,mt9m114"; + reg = <0x48>; + + clocks = <&clk24m 0>; + + reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>; + + vddio-supply = <®_cam_1v8>; + vdd-supply = <®_cam_1v8>; + vaa-supply = <®_2p8v>; + + port { + endpoint { + bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>; + link-frequencies = /bits/ 64 <384000000>; + remote-endpoint = <&mipi_csi_in>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,og01a1b.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,og01a1b.yaml new file mode 100644 index 000000000..ca57c0173 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,og01a1b.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2023-2024 Linaro Ltd. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,og01a1b.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OG01A1B Image Sensor + +maintainers: + - Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> + +description: + The OmniVision OG01A1B is black and white CMOS 1.3 Megapixel (1280x1024) + image sensor controlled over an I2C-compatible SCCB bus. + The sensor transmits images on a MIPI CSI-2 output interface with one or + two data lanes. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,og01a1b + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + reset-gpios: + description: Active low GPIO connected to XSHUTDOWN pad of the sensor. + maxItems: 1 + + strobe-gpios: + description: Input GPIO connected to strobe pad of the sensor. + maxItems: 1 + + avdd-supply: + description: Analogue circuit voltage supply. + + dovdd-supply: + description: I/O circuit voltage supply. + + dvdd-supply: + description: Digital circuit voltage supply. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + description: + Output port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 2 + items: + enum: [1, 2] + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@60 { + compatible = "ovti,og01a1b"; + reg = <0x60>; + clocks = <&clk 0>; + reset-gpios = <&gpio 117 GPIO_ACTIVE_LOW>; + avdd-supply = <&vreg_3v3>; + dovdd-supply = <&vreg_1p8>; + dvdd-supply = <&vreg_1p2>; + + port { + og01a1b_ep: endpoint { + remote-endpoint = <&csiphy_ep>; + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <500000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,og0ve1b.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,og0ve1b.yaml new file mode 100644 index 000000000..bd2f1ae23 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,og0ve1b.yaml @@ -0,0 +1,97 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,og0ve1b.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OG0VE1B Image Sensor + +description: + OmniVision OG0VE1B image sensor is a low power consuming monochrome + image sensor. The sensor is controlled over a serial camera control + bus protocol (SCCB), the widest supported image size is 640x480 at + 120 frames per second rate, data output format is 8/10-bit RAW + transferred over one-lane MIPI D-PHY at up to 800 Mbps. + +maintainers: + - Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,og0ve1b + + reg: + maxItems: 1 + + clocks: + description: XVCLK supply clock, 6MHz to 27MHz frequency. + maxItems: 1 + + reset-gpios: + description: Active low GPIO connected to XSHUTDOWN pad of the sensor. + maxItems: 1 + + strobe-gpios: + description: Input GPIO connected to strobe pad of the sensor. + maxItems: 1 + + avdd-supply: + description: Analog voltage supply, 2.6 to 3.0 volts. + + dovdd-supply: + description: Digital I/O voltage supply, 1.7 to 3.0 volts. + + dvdd-supply: + description: Digital core voltage supply. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + required: + - link-frequencies + +required: + - compatible + - reg + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3e { + compatible = "ovti,og0ve1b"; + reg = <0x3e>; + clocks = <&camera_clk 0>; + assigned-clocks = <&camera_clk 0>; + assigned-clock-rates = <24000000>; + reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + avdd-supply = <&vreg_2p8>; + dovdd-supply = <&vreg_1p8>; + dvdd-supply = <&vreg_1p2>; + + port { + endpoint { + link-frequencies = /bits/ 64 <500000000>; + remote-endpoint = <&mipi_csi2_ep>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,os05b10.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,os05b10.yaml new file mode 100644 index 000000000..b76771d81 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,os05b10.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,os05b10.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OS05B10 Image Sensor + +maintainers: + - Elgin Perumbilly <elgin.perumbilly@siliconsignals.io> + +description: + The OmniVision OS05B10 is a 5MP (2592x1944) color CMOS image sensor controlled + through an I2C-compatible SCCB bus. it outputs RAW10/RAW12 format and uses a + 1/2.78" optical format. + +properties: + compatible: + const: ovti,os05b10 + + reg: + maxItems: 1 + + clocks: + items: + - description: XCLK clock + + avdd-supply: + description: Analog Domain Power Supply (2.8v) + + dovdd-supply: + description: I/O Domain Power Supply (1.8v) + + dvdd-supply: + description: Digital Domain Power Supply (1.2v) + + reset-gpios: + maxItems: 1 + description: Reset Pin GPIO Control (active low) + + port: + description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + - items: + - const: 1 + - const: 2 + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - avdd-supply + - dovdd-supply + - dvdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera-sensor@36 { + compatible = "ovti,os05b10"; + reg = <0x36>; + clocks = <&os05b10_clk>; + reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + + avdd-supply = <&os05b10_avdd_2v8>; + dvdd-supply = <&os05b10_dvdd_1v2>; + dovdd-supply = <&os05b10_dovdd_1v8>; + + port { + cam_out: endpoint { + remote-endpoint = <&mipi_in_cam>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <600000000>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml new file mode 100644 index 000000000..0e1d9c390 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml @@ -0,0 +1,147 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov02a10.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV02A10 CMOS Sensor + +maintainers: + - Dongchun Zhu <dongchun.zhu@mediatek.com> + +description: |- + The Omnivision OV02A10 is a low-cost, high performance, 1/5-inch, 2 megapixel + image sensor, which is the latest production derived from Omnivision's CMOS + image sensor technology. Ihis chip supports high frame rate speeds up to 30fps + @ 1600x1200 (UXGA) resolution transferred over a 1-lane MIPI interface. The + sensor output is available via CSI-2 serial data output. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov02a10 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + description: + External clock for the sensor. + items: + - const: eclk + + clock-frequency: + description: + Frequency of the eclk clock in Hz. + deprecated: true + + dovdd-supply: + description: + Definition of the regulator used as Digital I/O voltage supply. + + avdd-supply: + description: + Definition of the regulator used as Analog voltage supply. + + dvdd-supply: + description: + Definition of the regulator used as Digital core voltage supply. + + powerdown-gpios: + description: + Must be the device tree identifier of the GPIO connected to the + PD_PAD pin. This pin is used to place the OV02A10 into standby mode + or shutdown mode. As the line needs to be high for the powerdown mode + to be active, it should be marked GPIO_ACTIVE_HIGH. + maxItems: 1 + + reset-gpios: + description: + Must be the device tree identifier of the GPIO connected to the + RST_PD pin. If specified, it will be asserted during driver probe. + As the line needs to be low for the reset to be active, it should be + marked GPIO_ACTIVE_LOW. + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + description: + Output port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + ovti,mipi-clock-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Definition of MIPI clock voltage unit. This entry corresponds to + the link speed defined by the 'link-frequencies' property. + If present, the value shall be in the range of 0-4. + default: 4 + + required: + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - clock-names + - dovdd-supply + - avdd-supply + - dvdd-supply + - powerdown-gpios + - reset-gpios + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov02a10: camera-sensor@3d { + compatible = "ovti,ov02a10"; + reg = <0x3d>; + + powerdown-gpios = <&pio 107 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pio 109 GPIO_ACTIVE_LOW>; + + clocks = <&ov02a10_clk>; + clock-names = "eclk"; + + rotation = <180>; + + dovdd-supply = <&ov02a10_dovdd>; + avdd-supply = <&ov02a10_avdd>; + dvdd-supply = <&ov02a10_dvdd>; + + port { + wcam_out: endpoint { + link-frequencies = /bits/ 64 <390000000>; + ovti,mipi-clock-voltage = <3>; + remote-endpoint = <&mipi_in_wcam>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov02e10.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov02e10.yaml new file mode 100644 index 000000000..03d476bcf --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov02e10.yaml @@ -0,0 +1,152 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2025 Linaro Ltd. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov02e10.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV02E10 CMOS Sensor + +maintainers: + - Bryan O'Donoghue <bryan.odonoghue@linaro.org> + +description: | + The Omnivision OV02E10 and OV02C10 sensors are 2 megapixel, CMOS image sensors which support: + - Automatic black level calibration (ABLC) + - Programmable controls for frame rate, mirror and flip, binning, cropping + and windowing + - OVO2C10 + - 10 bit RAW Bayer 1920x1080 60 fps 2-lane @ 800 Mbps/lane + - 10 bit RAW Bayer 1920x1080 60 fps 1-lane @ 1500 Mbps/lane + - 10 bit RAW Bayer 1280x720 60 fps cropped 1-lane @ 960 Mbps/lane + - 10 bit RGB/BW 640x480 60 fps bin2 or skip2 1-lane @ 800 Mbps/lane + - 10 bit RGB/BW 480x270 60 fps bin4 or skip4 1-lane @ 800 Mbps/lane + - OV02E10 + - 10 bit RAW Bayer 1920x1088 60 fps 2-lane @ 720 Mbps/lane + - 10 bit RAW Bayer 1280x1080 60 fps 2-lane @ 720 Mbps/lane + - 10 bit Quad Bayer 960x540 60 fps 2-lane 360 Mbps/lane + - 8 bit Quad Bayer 480x270 1/3/5/10 fps sub2 288 Mbps/lane + - 8 bit Quad Bayer 232x132 1/3/5/10 fps sub4 144 Mbps/lane + - Dynamic defect pixel cancellation + - Standard SCCB command interface + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + enum: + - ovti,ov02c10 + - ovti,ov02e10 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + avdd-supply: + description: Analogue circuit voltage supply. + + dovdd-supply: + description: I/O circuit voltage supply. + + dvdd-supply: + description: Digital circuit voltage supply. + + reset-gpios: + description: Active low GPIO connected to XSHUTDOWN pad of the sensor. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + additionalProperties: false + + properties: + data-lanes: + items: + - const: 1 + - const: 2 + link-frequencies: true + remote-endpoint: true + + required: + - data-lanes + - link-frequencies + - remote-endpoint + +required: + - compatible + - reg + - clocks + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov02e10: camera@10 { + compatible = "ovti,ov02e10"; + reg = <0x10>; + + reset-gpios = <&tlmm 237 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cam_rgb_defaultt>; + + clocks = <&ov02e10_clk>; + + assigned-clocks = <&ov02e10_clk>; + assigned-clock-parents = <&ov02e10_clk_parent>; + assigned-clock-rates = <19200000>; + + avdd-supply = <&vreg_l7b_2p8>; + dvdd-supply = <&vreg_l7b_1p8>; + dovdd-supply = <&vreg_l3m_1p8>; + + port { + ov02e10_ep: endpoint { + remote-endpoint = <&csiphy4_ep>; + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <400000000>; + }; + }; + }; + + ov02c10: camera@36 { + compatible = "ovti,ov02c10"; + reg = <0x36>; + + reset-gpios = <&tlmm 237 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cam_rgb_defaultt>; + + clocks = <&ov02c10_clk>; + + assigned-clocks = <&ov02c10_clk>; + assigned-clock-parents = <&ov02c10_clk_parent>; + assigned-clock-rates = <19200000>; + + avdd-supply = <&vreg_l7b_2p8>; + dvdd-supply = <&vreg_l7b_1p8>; + dovdd-supply = <&vreg_l3m_1p8>; + + port { + ov02c10_ep: endpoint { + remote-endpoint = <&csiphy4_ep>; + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <400000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov08d10.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov08d10.yaml new file mode 100644 index 000000000..6f2017c75 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov08d10.yaml @@ -0,0 +1,101 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov08d10.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV08D10 1/4-Inch 8MP CMOS color image sensor + +maintainers: + - Matthias Fend <matthias.fend@emfend.at> + +description: + The Omnivision OV08D10 is a 1/4-Inch 8MP CMOS color image sensor with an + active array size of 3280 x 2464. It is programmable through I2C + interface. Image data is transmitted via MIPI CSI-2 using 2 lanes. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov08d10 + + reg: + maxItems: 1 + + clocks: + description: MCLK input clock (6 - 27 MHz) + maxItems: 1 + + reset-gpios: + description: Active low XSHUTDN pin + maxItems: 1 + + dovdd-supply: + description: IO power supply (1.8V) + + avdd-supply: + description: Analog power supply (2.8V) + + dvdd-supply: + description: Core power supply (1.2V) + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@36 { + compatible = "ovti,ov08d10"; + reg = <0x36>; + + clocks = <&ov08d10_clk>; + + dovdd-supply = <&ov08d10_vdddo_1v8>; + avdd-supply = <&ov08d10_vdda_2v8>; + dvdd-supply = <&ov08d10_vddd_1v2>; + + orientation = <2>; + rotation = <0>; + + reset-gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + + port { + ov08d10_output: endpoint { + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <360000000 720000000>; + remote-endpoint = <&csi_input>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov08x40.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov08x40.yaml new file mode 100644 index 000000000..552efdf89 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov08x40.yaml @@ -0,0 +1,120 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2024 Linaro Ltd. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov08x40.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV08X40 CMOS Sensor + +maintainers: + - Bryan O'Donoghue <bryan.odonoghue@linaro.org> + +description: | + The Omnivision OV08X40 is a 9.2 megapixel, CMOS image sensor which supports: + - Automatic black level calibration (ABLC) + - Programmable controls for frame rate, mirror and flip, binning, cropping + and windowing + - Output formats 10-bit 4C RGB RAW, 10-bit Bayer RAW + - 4-lane MIPI D-PHY TX @ 1 Gbps per lane + - 2-lane MPIP D-PHY TX @ 2 Gbps per lane + - Dynamic defect pixel cancellation + - Standard SCCB command interface + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov08x40 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + avdd-supply: + description: Analogue circuit voltage supply. + + dovdd-supply: + description: I/O circuit voltage supply. + + dvdd-supply: + description: Digital circuit voltage supply. + + reset-gpios: + description: Active low GPIO connected to XSHUTDOWN pad of the sensor. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + additionalProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + link-frequencies: true + remote-endpoint: true + + required: + - data-lanes + - link-frequencies + - remote-endpoint + +required: + - compatible + - reg + - clocks + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov08x40: camera@36 { + compatible = "ovti,ov08x40"; + reg = <0x36>; + + reset-gpios = <&tlmm 111 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cam_rgb_defaultt>; + + clocks = <&ov08x40_clk>; + + assigned-clocks = <&ov08x40_clk>; + assigned-clock-parents = <&ov08x40_clk_parent>; + assigned-clock-rates = <19200000>; + + avdd-supply = <&vreg_l7b_2p8>; + dvdd-supply = <&vreg_l7b_1p8>; + dovdd-supply = <&vreg_l3m_1p8>; + + port { + ov08x40_ep: endpoint { + remote-endpoint = <&csiphy4_ep>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <400000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2640.txt b/Documentation/devicetree/bindings/media/i2c/ovti,ov2640.txt new file mode 100644 index 000000000..989ce6cb6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2640.txt @@ -0,0 +1,41 @@ +* Omnivision OV2640 CMOS sensor + +The Omnivision OV2640 sensor supports multiple resolutions output, such as +CIF, SVGA, UXGA. It also can support the YUV422/420, RGB565/555 or raw RGB +output formats. + +Required Properties: +- compatible: should be "ovti,ov2640" +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". + +Optional Properties: +- resetb-gpios: reference to the GPIO connected to the resetb pin, if any. +- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c1: i2c@f0018000 { + ov2640: camera@30 { + compatible = "ovti,ov2640"; + reg = <0x30>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; + resetb-gpios = <&pioE 11 GPIO_ACTIVE_LOW>; + pwdn-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>; + clocks = <&pck0>; + clock-names = "xvclk"; + assigned-clocks = <&pck0>; + assigned-clock-rates = <25000000>; + + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2659.txt b/Documentation/devicetree/bindings/media/i2c/ovti,ov2659.txt new file mode 100644 index 000000000..92989a619 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2659.txt @@ -0,0 +1,47 @@ +* OV2659 1/5-Inch 2Mp SOC Camera + +The Omnivision OV2659 is a 1/5-inch SOC camera, with an active array size of +1632H x 1212V. It is programmable through a SCCB. The OV2659 sensor supports +multiple resolutions output, such as UXGA, SVGA, 720p. It also can support +YUV422, RGB565/555 or raw RGB output formats. + +Required Properties: +- compatible: Must be "ovti,ov2659" +- reg: I2C slave address +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". +- link-frequencies: target pixel clock frequency. + +Optional Properties: +- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any. + Active high with internal pull down resistor. +- reset-gpios: reference to the GPIO connected to the resetb pin, if any. + Active low with internal pull up resistor. + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + ov2659@30 { + compatible = "ovti,ov2659"; + reg = <0x30>; + + clocks = <&clk_ov2659 0>; + clock-names = "xvclk"; + + powerdown-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>; + + port { + ov2659_0: endpoint { + remote-endpoint = <&vpfe_ep>; + link-frequencies = /bits/ 64 <70000000>; + }; + }; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml new file mode 100644 index 000000000..634d3b821 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov2680.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV2680 CMOS Sensor + +maintainers: + - Rui Miguel Silva <rmfrfs@gmail.com> + +description: |- + The OV2680 color sensor is a low voltage, high performance 1/5 inch UXGA (2 + megapixel) CMOS image sensor that provides a single-chip UXGA (1600 x 1200) + camera. It provides full-frame, sub-sampled, or windowed 10-bit images in + various formats via the control of the Serial Camera Control Bus (SCCB) + interface. The OV2680 has an image array capable of operating at up to 30 + frames per second (fps) in UXGA resolution. + +properties: + compatible: + const: ovti,ov2680 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: xvclk + + reset-gpios: + description: + The phandle and specifier for the GPIO that controls sensor reset. + This corresponds to the hardware pin XSHUTDOWN which is physically + active low. + maxItems: 1 + + DOVDD-supply: + description: + Definition of the regulator used as interface power supply. + + AVDD-supply: + description: + Definition of the regulator used as analog power supply. + + DVDD-supply: + description: + Definition of the regulator used as digital power supply. + + port: + description: + A node containing an output port node. + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + additionalProperties: false + + properties: + link-frequencies: true + + remote-endpoint: true + + required: + - link-frequencies + +required: + - compatible + - reg + - clocks + - clock-names + - DOVDD-supply + - AVDD-supply + - DVDD-supply + - reset-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov2680: camera-sensor@36 { + compatible = "ovti,ov2680"; + reg = <0x36>; + clocks = <&osc>; + clock-names = "xvclk"; + reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; + + DOVDD-supply = <&sw2_reg>; + DVDD-supply = <&sw2_reg>; + AVDD-supply = <®_peri_3p15v>; + + port { + ov2680_to_mipi: endpoint { + remote-endpoint = <&mipi_from_sensor>; + link-frequencies = /bits/ 64 <330000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2685.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2685.yaml new file mode 100644 index 000000000..e2ffe0a9c --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2685.yaml @@ -0,0 +1,102 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov2685.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV2685 Image Sensor + +maintainers: + - Shunqian Zheng <zhengsq@rock-chips.com> + +properties: + compatible: + const: ovti,ov2685 + + reg: + maxItems: 1 + + clocks: + items: + - description: XVCLK clock + + clock-names: + items: + - const: xvclk + + dvdd-supply: + description: Digital Domain Power Supply + + avdd-supply: + description: Analog Domain Power Supply + + dovdd-supply: + description: I/O Domain Power Supply + + reset-gpios: + maxItems: 1 + description: Reset Pin GPIO Control (active low) + + port: + description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 2 + + required: + - data-lanes + +required: + - compatible + - reg + - clocks + - clock-names + - dvdd-supply + - avdd-supply + - dovdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3399-cru.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov2685: camera-sensor@3c { + compatible = "ovti,ov2685"; + reg = <0x3c>; + pinctrl-names = "default"; + pinctrl-0 = <&clk_24m_cam>; + + clocks = <&cru SCLK_TESTCLKOUT1>; + clock-names = "xvclk"; + + avdd-supply = <&pp2800_cam>; + dovdd-supply = <&pp1800>; + dvdd-supply = <&pp1800>; + reset-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + + port { + ucam_out: endpoint { + remote-endpoint = <&mipi_in_ucam>; + data-lanes = <1>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2732.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2732.yaml new file mode 100644 index 000000000..814fc568c --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2732.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov2732.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV2732 Image Sensor + +maintainers: + - Walter Werner Schneider <contact@schnwalter.eu> + +description: + The OmniVision OV2732 is a 2MP (1920x1080) color CMOS image sensor controlled + through an I2C-compatible SCCB bus. + +properties: + compatible: + const: ovti,ov2732 + + reg: + maxItems: 1 + + clocks: + items: + - description: XVCLK clock + + avdd-supply: + description: Analog Domain Power Supply + + dovdd-supply: + description: I/O Domain Power Supply + + dvdd-supply: + description: Digital Domain Power Supply + + powerdown-gpios: + maxItems: 1 + description: Reference to the GPIO connected to the pwdn pin. Active low. + + reset-gpios: + maxItems: 1 + description: Reference to the GPIO connected to the reset pin. Active low. + + port: + description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + items: + - const: 1 + - const: 2 + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - avdd-supply + - dovdd-supply + - dvdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov2732: camera@36 { + compatible = "ovti,ov2732"; + reg = <0x36>; + clocks = <&ov2732_clk>; + + avdd-supply = <&ov2732_avdd>; + dovdd-supply = <&ov2732_dovdd>; + dvdd-supply = <&ov2732_dvdd>; + + powerdown-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; + + port { + camera_out: endpoint { + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <360000000>; + remote-endpoint = <&mipi_in_camera>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml new file mode 100644 index 000000000..bb34f2151 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2735.yaml @@ -0,0 +1,108 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov2735.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV2735 Image Sensor + +maintainers: + - Himanshu Bhavani <himanshu.bhavani@siliconsignals.io> + +description: + The OmniVision OV2735 is a 2MP (1920x1080) color CMOS image sensor controlled + through an I2C-compatible SCCB bus. it outputs RAW10 format and uses a 1/2.7" + optical format. + +properties: + compatible: + const: ovti,ov2735 + + reg: + maxItems: 1 + + clocks: + items: + - description: XVCLK clock + + avdd-supply: + description: Analog Domain Power Supply + + dovdd-supply: + description: I/O Domain Power Supply + + dvdd-supply: + description: Digital Domain Power Supply + + reset-gpios: + maxItems: 1 + description: Reset Pin GPIO Control (active low) + + enable-gpios: + maxItems: 1 + description: + Active-low enable pin. Labeled as 'PWDN' in the datasheet, but acts as + an enable signal. During power rail ramp-up, the device remains powered + down. Once power rails are stable, pulling this pin low powers on the + device. + + port: + description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + items: + - const: 1 + - const: 2 + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - avdd-supply + - dovdd-supply + - dvdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera-sensor@3c { + compatible = "ovti,ov2735"; + reg = <0x3c>; + clocks = <&ov2735_clk>; + + avdd-supply = <&ov2735_avdd>; + dovdd-supply = <&ov2735_dovdd>; + dvdd-supply = <&ov2735_dvdd>; + + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpio2 11 GPIO_ACTIVE_LOW>; + + port { + cam_out: endpoint { + remote-endpoint = <&mipi_in_cam>; + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <420000000>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov4689.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov4689.yaml new file mode 100644 index 000000000..d96199031 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov4689.yaml @@ -0,0 +1,130 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov4689.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV4689 CMOS + +maintainers: + - Mikhail Rudenko <mike.rudenko@gmail.com> + +description: | + The Omnivision OV4689 is a high performance, 1/3-inch, 4 megapixel + image sensor. Ihis chip supports high frame rate speeds up to 90 fps + at 2688x1520 resolution. It is programmable through an I2C + interface, and sensor output is sent via 1/2/4 lane MIPI CSI-2 + connection. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov4689 + + reg: + maxItems: 1 + + clocks: + description: + External clock (XVCLK) for the sensor, 6-64 MHz + maxItems: 1 + + dovdd-supply: + description: + Digital I/O voltage supply, 1.7-3.0 V + + avdd-supply: + description: + Analog voltage supply, 2.6-3.0 V + + dvdd-supply: + description: + Digital core voltage supply, 1.1-1.3 V + + powerdown-gpios: + description: + GPIO connected to the powerdown pin (active low) + + reset-gpios: + maxItems: 1 + description: + GPIO connected to the reset pin (active low) + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + description: + Output port node, single endpoint describing the CSI-2 transmitter + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + link-frequencies: true + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - dovdd-supply + - avdd-supply + - dvdd-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov4689: camera@36 { + compatible = "ovti,ov4689"; + reg = <0x36>; + + clocks = <&ov4689_clk>; + + avdd-supply = <&ov4689_avdd>; + dovdd-supply = <&ov4689_dovdd>; + dvdd-supply = <&ov4689_dvdd>; + + powerdown-gpios = <&pio 107 GPIO_ACTIVE_LOW>; + reset-gpios = <&pio 109 GPIO_ACTIVE_LOW>; + + orientation = <2>; + rotation = <0>; + + port { + wcam_out: endpoint { + remote-endpoint = <&mipi_in_wcam>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <504000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml new file mode 100644 index 000000000..2c5e69356 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml @@ -0,0 +1,149 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5640.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV5640 Image Sensor + +maintainers: + - Steve Longerbeam <slongerbeam@gmail.com> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov5640 + + reg: + maxItems: 1 + + clocks: + description: XCLK Input Clock + + clock-names: + const: xclk + + AVDD-supply: + description: Analog voltage supply, 2.8 volts + + DVDD-supply: + description: Digital core voltage supply, 1.5 volts + + DOVDD-supply: + description: Digital I/O voltage supply, 1.8 volts + + powerdown-gpios: + maxItems: 1 + description: > + Reference to the GPIO connected to the powerdown pin, if any. + + reset-gpios: + maxItems: 1 + description: > + Reference to the GPIO connected to the reset pin, if any. + + port: + description: Digital Output Port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + const: 0 + + data-lanes: + minItems: 1 + maxItems: 2 + items: + enum: [1, 2] + + bus-width: + enum: [8, 10] + + data-shift: + enum: [0, 2] + +required: + - compatible + - reg + - clocks + - clock-names + - AVDD-supply + - DVDD-supply + - DOVDD-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/imx6qdl-clock.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clks IMX6QDL_CLK_CKO>; + clock-names = "xclk"; + DOVDD-supply = <&vgen4_reg>; /* 1.8v */ + AVDD-supply = <&vgen3_reg>; /* 2.8v */ + DVDD-supply = <&vgen2_reg>; /* 1.5v */ + powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + rotation = <180>; + + port { + /* MIPI CSI-2 bus endpoint */ + ov5640_to_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_from_ov5640>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; + }; + + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clk_ext_camera>; + clock-names = "xclk"; + DOVDD-supply = <&vgen4_reg>; /* 1.8v */ + AVDD-supply = <&vgen3_reg>; /* 2.8v */ + DVDD-supply = <&vgen2_reg>; /* 1.5v */ + + port { + /* Parallel bus endpoint */ + ov5640_to_parallel: endpoint { + remote-endpoint = <¶llel_from_ov5640>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5642.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5642.yaml new file mode 100644 index 000000000..01f8b2b3f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5642.yaml @@ -0,0 +1,141 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5642.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV5642 Image Sensor + +maintainers: + - Fabio Estevam <festevam@gmail.com> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov5642 + + reg: + maxItems: 1 + + clocks: + description: XCLK Input Clock + + AVDD-supply: + description: Analog voltage supply, 2.8V. + + DVDD-supply: + description: Digital core voltage supply, 1.5V. + + DOVDD-supply: + description: Digital I/O voltage supply, 1.8V. + + powerdown-gpios: + maxItems: 1 + description: Reference to the GPIO connected to the powerdown pin, if any. + + reset-gpios: + maxItems: 1 + description: Reference to the GPIO connected to the reset pin, if any. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + description: | + Video output port. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + enum: [5, 6] + + bus-width: + enum: [8, 10] + default: 10 + + data-shift: + enum: [0, 2] + default: 0 + + hsync-active: + enum: [0, 1] + default: 1 + + vsync-active: + enum: [0, 1] + default: 1 + + pclk-sample: + enum: [0, 1] + default: 1 + + allOf: + - if: + properties: + bus-type: + const: 6 + then: + properties: + hsync-active: false + vsync-active: false + + - if: + properties: + bus-width: + const: 10 + then: + properties: + data-shift: + const: 0 + + required: + - bus-type + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "ovti,ov5642"; + reg = <0x3c>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5642>; + clocks = <&clk_ext_camera>; + DOVDD-supply = <&vgen4_reg>; + AVDD-supply = <&vgen3_reg>; + DVDD-supply = <&vgen2_reg>; + powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + + port { + ov5642_to_parallel: endpoint { + bus-type = <MEDIA_BUS_TYPE_PARALLEL>; + remote-endpoint = <¶llel_from_ov5642>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml new file mode 100644 index 000000000..a583714b1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml @@ -0,0 +1,108 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5645.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV5645 Image Sensor + +maintainers: + - Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> + +properties: + compatible: + const: ovti,ov5645 + + reg: + maxItems: 1 + + clocks: + description: XCLK Input Clock + + clock-frequency: + description: Frequency of the xclk clock in Hz. + deprecated: true + + vdda-supply: + description: Analog voltage supply, 2.8 volts + + vddd-supply: + description: Digital core voltage supply, 1.5 volts + + vdddo-supply: + description: Digital I/O voltage supply, 1.8 volts + + enable-gpios: + maxItems: 1 + description: + Reference to the GPIO connected to the PWDNB pin, if any. + + reset-gpios: + maxItems: 1 + description: + Reference to the GPIO connected to the RESETB pin, if any. + + port: + description: Digital Output Port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 2 + items: + enum: [1, 2] + + required: + - data-lanes + +required: + - compatible + - reg + - clocks + - vdddo-supply + - vdda-supply + - vddd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "ovti,ov5645"; + reg = <0x3c>; + + clocks = <&clks 1>; + assigned-clocks = <&clks 1>; + assigned-clock-rates = <24000000>; + + vdddo-supply = <&ov5645_vdddo_1v8>; + vdda-supply = <&ov5645_vdda_2v8>; + vddd-supply = <&ov5645_vddd_1v5>; + enable-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5645>; + + port { + ov5645_ep: endpoint { + remote-endpoint = <&csi0_ep>; + data-lanes = <1 2>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5647.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5647.yaml new file mode 100644 index 000000000..2d7937a37 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5647.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5647.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV5647 raw image sensor + +maintainers: + - Dave Stevenson <dave.stevenson@raspberrypi.com> + - Jacopo Mondi <jacopo@jmondi.org> + +description: |- + The OV5647 is a raw image sensor with MIPI CSI-2 and CCP2 image data + interfaces and CCI (I2C compatible) control bus. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov5647 + + reg: + description: I2C device address. + maxItems: 1 + + clocks: + description: Reference to the xclk clock. + maxItems: 1 + + pwdn-gpios: + description: Reference to the GPIO connected to the pwdn pin. Active high. + maxItems: 1 + + avdd-supply: + description: Analog voltage supply, 2.8 volts + + dvdd-supply: + description: Digital core voltage supply, 1.5 volts + + dovdd-supply: + description: Digital I/O voltage supply, 1.7 - 3.0 volts + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-noncontinuous: true + +required: + - compatible + - reg + - clocks + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov5647: camera@36 { + compatible = "ovti,ov5647"; + reg = <0x36>; + clocks = <&camera_clk>; + pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>; + + port { + camera_out: endpoint { + remote-endpoint = <&csi1_ep1>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5648.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5648.yaml new file mode 100644 index 000000000..8028c8b10 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5648.yaml @@ -0,0 +1,98 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5648.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV5648 Image Sensor + +maintainers: + - Paul Kocialkowski <paul.kocialkowski@bootlin.com> + +properties: + compatible: + const: ovti,ov5648 + + reg: + maxItems: 1 + + clocks: + items: + - description: XVCLK Clock + + dvdd-supply: + description: Digital Domain Power Supply + + avdd-supply: + description: Analog Domain Power Supply (internal AVDD is used if missing) + + dovdd-supply: + description: I/O Domain Power Supply + + powerdown-gpios: + maxItems: 1 + description: Power Down Pin GPIO Control (active low) + + reset-gpios: + maxItems: 1 + description: Reset Pin GPIO Control (active low) + + port: + description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + + data-lanes: + minItems: 1 + maxItems: 2 + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - dvdd-supply + - dovdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/sun8i-v3s-ccu.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov5648: camera@36 { + compatible = "ovti,ov5648"; + reg = <0x36>; + + dvdd-supply = <&ov5648_dvdd>; + avdd-supply = <&ov5648_avdd>; + dovdd-supply = <&ov5648_dovdd>; + clocks = <&ov5648_xvclk 0>; + + ov5648_out: port { + ov5648_out_mipi_csi2: endpoint { + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <210000000 168000000>; + + remote-endpoint = <&mipi_csi2_in_ov5648>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5670.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5670.yaml new file mode 100644 index 000000000..6e089fe1d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5670.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5670.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV5670 5 Megapixels raw image sensor + +maintainers: + - Jacopo Mondi <jacopo.mondi@ideasonboard.com> + +description: |- + The OV5670 is a 5 Megapixels raw image sensor which provides images in 10-bits + RAW BGGR Bayer format on a 2 data lanes MIPI CSI-2 serial interface and is + controlled through an I2C compatible control bus. + +properties: + compatible: + const: ovti,ov5670 + + reg: + maxItems: 1 + + clocks: + description: System clock. From 6 to 27 MHz. + maxItems: 1 + + powerdown-gpios: + description: Reference to the GPIO connected to the PWDNB pin. Active low. + + reset-gpios: + description: Reference to the GPIO connected to the XSHUTDOWN pin. Active low. + maxItems: 1 + + avdd-supply: + description: Analog circuit power. Typically 2.8V. + + dvdd-supply: + description: Digital circuit power. Typically 1.2V. + + dovdd-supply: + description: Digital I/O circuit power. Typically 2.8V or 1.8V. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + additionalProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 2 + items: + enum: [1, 2] + + clock-noncontinuous: true + remote-endpoint: true + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov5670: sensor@36 { + compatible = "ovti,ov5670"; + reg = <0x36>; + + clocks = <&sensor_xclk>; + + port { + ov5670_ep: endpoint { + remote-endpoint = <&csi_ep>; + data-lanes = <1 2>; + clock-noncontinuous; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5675.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5675.yaml new file mode 100644 index 000000000..ad0720405 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5675.yaml @@ -0,0 +1,122 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2022 Theobroma Systems Design und Consulting GmbH +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5675.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV5675 CMOS Sensor + +maintainers: + - Quentin Schulz <quentin.schulz@theobroma-systems.com> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +description: | + The Omnivision OV5675 is a high performance, 1/5-inch, 5 megapixel, CMOS + image sensor that delivers 2592x1944 at 30fps. It provides full-frame, + sub-sampled, and windowed 10-bit MIPI images in various formats via the + Serial Camera Control Bus (SCCB) interface. + + This chip is programmable through I2C and two-wire SCCB. The sensor output + is available via CSI-2 serial data output (up to 2-lane). + +properties: + compatible: + const: ovti,ov5675 + + reg: + maxItems: 1 + + clocks: + description: + System input clock (aka XVCLK). From 6 to 27 MHz. + maxItems: 1 + + dovdd-supply: + description: + Digital I/O voltage supply, 1.8 volts. + + avdd-supply: + description: + Analog voltage supply, 2.8 volts. + + dvdd-supply: + description: + Digital core voltage supply, 1.2 volts. + + reset-gpios: + description: + The phandle and specifier for the GPIO that controls sensor reset. + This corresponds to the hardware pin XSHUTDN which is physically + active low. + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 2 + + # Supports max data transfer of 900 Mbps per lane + link-frequencies: true + +required: + - compatible + - reg + - clocks + - dovdd-supply + - avdd-supply + - dvdd-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/px30-cru.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/pinctrl/rockchip.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov5675: camera@36 { + compatible = "ovti,ov5675"; + reg = <0x36>; + + reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cif_clkout_m0>; + + clocks = <&cru SCLK_CIF_OUT>; + assigned-clocks = <&cru SCLK_CIF_OUT>; + assigned-clock-rates = <19200000>; + + avdd-supply = <&vcc_1v8>; + dvdd-supply = <&vcc_1v2>; + dovdd-supply = <&vcc_2v8>; + + rotation = <90>; + orientation = <0>; + + port { + ucam_out: endpoint { + remote-endpoint = <&mipi_in_ucam>; + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <450000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml new file mode 100644 index 000000000..3368b3bd8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml @@ -0,0 +1,141 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2022 Amarulasolutions +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5693.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV5693/OV5695 CMOS Sensors + +maintainers: + - Tommaso Merciai <tomm.merciai@gmail.com> + +description: | + The Omnivision OV5693/OV5695 are high performance, 1/4-inch, 5 megapixel, CMOS + image sensors that deliver 2592x1944 at 30fps. It provides full-frame, + sub-sampled, and windowed 10-bit MIPI images in various formats via the + Serial Camera Control Bus (SCCB) interface. + + OV5693/OV5695 are controlled via I2C and two-wire Serial Camera Control Bus + (SCCB). The sensor output is available via CSI-2 serial data output (up to + 2-lane). + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + - if: + properties: + compatible: + contains: + const: ovti,ov5693 + then: + properties: + port: + properties: + endpoint: + required: + - link-frequencies + +properties: + compatible: + enum: + - ovti,ov5693 + - ovti,ov5695 + + reg: + maxItems: 1 + + clocks: + description: + System input clock (aka XVCLK). From 6 to 27 MHz. + maxItems: 1 + + clock-names: + const: xvclk + + dovdd-supply: + description: + Digital I/O voltage supply, 1.8V. + + avdd-supply: + description: + Analog voltage supply, 2.8V. + + dvdd-supply: + description: + Digital core voltage supply, 1.2V. + + reset-gpios: + description: + The phandle and specifier for the GPIO that controls sensor reset. + This corresponds to the hardware pin XSHUTDN which is physically + active low. + maxItems: 1 + + port: + description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + + data-lanes: + minItems: 1 + maxItems: 2 + + required: + - data-lanes + +required: + - compatible + - reg + - clocks + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/px30-cru.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/pinctrl/rockchip.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov5693: camera@36 { + compatible = "ovti,ov5693"; + reg = <0x36>; + + reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cif_clkout_m0>; + + clocks = <&cru SCLK_CIF_OUT>; + assigned-clocks = <&cru SCLK_CIF_OUT>; + assigned-clock-rates = <19200000>; + + avdd-supply = <&vcc_1v8>; + dvdd-supply = <&vcc_1v2>; + dovdd-supply = <&vcc_2v8>; + + rotation = <90>; + orientation = <0>; + + port { + ucam_out: endpoint { + remote-endpoint = <&mipi_in_ucam>; + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <450000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov6211.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov6211.yaml new file mode 100644 index 000000000..5a857fa2f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov6211.yaml @@ -0,0 +1,96 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov6211.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV6211 Image Sensor + +description: + OmniVision OV6211 image sensor is a high performance monochrome image + sensor. The sensor is controlled over a serial camera control bus + protocol (SCCB), the widest supported output image frame size is 400x400 + at 120 frames per second rate, data output format is 8/10-bit RAW + transferred over one-lane MIPI D-PHY interface. + +maintainers: + - Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov6211 + + reg: + maxItems: 1 + + clocks: + description: XVCLK supply clock, 6MHz to 27MHz frequency. + maxItems: 1 + + reset-gpios: + description: Active low GPIO connected to XSHUTDOWN pad of the sensor. + maxItems: 1 + + strobe-gpios: + description: Input GPIO connected to strobe pad of the sensor. + maxItems: 1 + + avdd-supply: + description: Analogue voltage supply, 2.6 to 3.0 volts. + + dovdd-supply: + description: Digital I/O voltage supply, 1.8 volts. + + dvdd-supply: + description: Digital core voltage supply. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + required: + - link-frequencies + +required: + - compatible + - reg + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@60 { + compatible = "ovti,ov6211"; + reg = <0x60>; + clocks = <&camera_clk 0>; + assigned-clocks = <&camera_clk 0>; + assigned-clock-rates = <24000000>; + reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + avdd-supply = <&vreg_2p8>; + dovdd-supply = <&vreg_1p8>; + dvdd-supply = <&vreg_1p2>; + + port { + endpoint { + link-frequencies = /bits/ 64 <480000000>; + remote-endpoint = <&mipi_csi2_ep>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml new file mode 100644 index 000000000..2b6143aff --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov64a40.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV64A40 Image Sensor + +maintainers: + - Jacopo Mondi <jacopo.mondi@ideasonboard.com> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov64a40 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + avdd-supply: + description: Analog voltage supply, 2.8 volts + + dvdd-supply: + description: Digital core voltage supply, 1.1 volts + + dovdd-supply: + description: Digital I/O voltage supply, 1.8 volts + + powerdown-gpios: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + additionalProperties: false + + properties: + bus-type: + enum: + - 1 # MIPI CSI-2 C-PHY + - 4 # MIPI CSI-2 D-PHY + data-lanes: true + link-frequencies: true + clock-noncontinuous: true + remote-endpoint: true + + required: + - bus-type + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@36 { + compatible = "ovti,ov64a40"; + reg = <0x36>; + clocks = <&camera_clk>; + dovdd-supply = <&vgen4_reg>; + avdd-supply = <&vgen3_reg>; + dvdd-supply = <&vgen2_reg>; + powerdown-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + rotation = <180>; + orientation = <2>; + + port { + endpoint { + remote-endpoint = <&mipi_csi2_in>; + bus-type = <4>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <456000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov7251.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov7251.yaml new file mode 100644 index 000000000..922996da5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov7251.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov7251.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV7251 Image Sensor + +description: + The Omnivision OV7251 is a 1/7.5-Inch CMOS active pixel digital image sensor + with an active array size of 640H x 480V. It is programmable through a serial + I2C interface. + +maintainers: + - Todor Tomov <todor.too@gmail.com> + +properties: + compatible: + const: ovti,ov7251 + + reg: + maxItems: 1 + + clocks: + description: XCLK Input Clock + + clock-names: + const: xclk + + clock-frequency: + description: Frequency of the xclk clock in Hz. + deprecated: true + + vdda-supply: + description: Analog voltage supply, 2.8 volts + + vddd-supply: + description: Digital core voltage supply, 1.2 volts + + vdddo-supply: + description: Digital I/O voltage supply, 1.8 volts + + enable-gpios: + maxItems: 1 + description: + Reference to the GPIO connected to the XSHUTDOWN pin, if any. Polarity + is GPIO_ACTIVE_HIGH. + + port: + description: Digital Output Port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maximum: 1 + + data-lanes: + maxItems: 1 + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - vdddo-supply + - vdda-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "ovti,ov7251"; + reg = <0x3c>; + + clocks = <&clks 1>; + assigned-clocks = <&clks 1>; + assigned-clock-rates = <24000000>; + + vdddo-supply = <&ov7251_vdddo_1v8>; + vdda-supply = <&ov7251_vdda_2v8>; + vddd-supply = <&ov7251_vddd_1v5>; + enable-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + + port { + ov7251_ep: endpoint { + remote-endpoint = <&csi0_ep>; + clock-lanes = <1>; + data-lanes = <0>; + link-frequencies = /bits/ 64 <240000000 319200000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov7670.txt b/Documentation/devicetree/bindings/media/i2c/ovti,ov7670.txt new file mode 100644 index 000000000..2c972a56f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov7670.txt @@ -0,0 +1,55 @@ +* Omnivision OV7670 CMOS sensor + +The Omnivision OV7670 sensor supports multiple resolutions output, such as +CIF, SVGA, UXGA. It also can support the YUV422/420, RGB565/555 or raw RGB +output formats. + +Required Properties: +- compatible: should be "ovti,ov7670" +- clocks: reference to the xclk input clock. +- clock-names: should be "xclk". + +Required Endpoint Properties: +- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. +- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the resetb pin, if any. + Active is low. +- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any. + Active is high. +- ov7670,pclk-hb-disable: a boolean property to suppress pixel clock output + signal during horizontal blankings. + +The device node must contain one 'port' child node with one 'endpoint' child +sub-node for its digital output video port, in accordance with the video +interface bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c1: i2c@f0018000 { + ov7670: camera@21 { + compatible = "ovti,ov7670"; + reg = <0x21>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; + reset-gpios = <&pioE 11 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>; + clocks = <&pck0>; + clock-names = "xclk"; + assigned-clocks = <&pck0>; + assigned-clock-rates = <25000000>; + + ov7670,pclk-hb-disable; + + port { + ov7670_0: endpoint { + hsync-active = <0>; + vsync-active = <0>; + + remote-endpoint = <&isi_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov772x.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov772x.yaml new file mode 100644 index 000000000..5d24edba8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov772x.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov772x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV7720/OV7725 CMOS sensor + +maintainers: + - Jacopo Mondi <jacopo@jmondi.org> + +description: | + The Omnivision OV7720/OV7725 sensor supports multiple resolutions output, + such as VGA, QVGA, and any size scaling down from CIF to 40x30. It also can + support the YUV422, RGB565/555/444, GRB422 or raw RGB output formats. + +properties: + compatible: + enum: + - ovti,ov7720 + - ovti,ov7725 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + reset-gpios: + description: | + Reference to the GPIO connected to the RSTB pin which is active low. + maxItems: 1 + + powerdown-gpios: + description: | + Reference to the GPIO connected to the PWDN pin which is active high. + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + description: | + Video output port. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + enum: [5, 6] + + bus-width: + enum: [8, 10] + default: 10 + + data-shift: + enum: [0, 2] + default: 0 + + hsync-active: + enum: [0, 1] + default: 1 + + vsync-active: + enum: [0, 1] + default: 1 + + pclk-sample: + enum: [0, 1] + default: 1 + + allOf: + - if: + properties: + bus-type: + const: 6 + then: + properties: + hsync-active: false + vsync-active: false + + - if: + properties: + bus-width: + const: 10 + then: + properties: + data-shift: + const: 0 + + required: + - bus-type + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + ov772x: camera@21 { + compatible = "ovti,ov7725"; + reg = <0x21>; + reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_LOW>; + clocks = <&xclk>; + + port { + ov772x_0: endpoint { + bus-type = <MEDIA_BUS_TYPE_PARALLEL>; + vsync-active = <0>; + hsync-active = <0>; + pclk-sample = <0>; + bus-width = <8>; + data-shift = <0>; + remote-endpoint = <&vcap1_in0>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov7740.txt b/Documentation/devicetree/bindings/media/i2c/ovti,ov7740.txt new file mode 100644 index 000000000..af781c3a5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov7740.txt @@ -0,0 +1,47 @@ +* Omnivision OV7740 CMOS image sensor + +The Omnivision OV7740 image sensor supports multiple output image +size, such as VGA, and QVGA, CIF and any size smaller. It also +supports the RAW RGB and YUV output formats. + +The common video interfaces bindings (see video-interfaces.txt) should +be used to specify link to the image data receiver. The OV7740 device +node should contain one 'port' child node with an 'endpoint' subnode. + +Required Properties: +- compatible: "ovti,ov7740". +- reg: I2C slave address of the sensor. +- clocks: Reference to the xvclk input clock. +- clock-names: "xvclk". + +Optional Properties: +- reset-gpios: Rreference to the GPIO connected to the reset_b pin, + if any. Active low with pull-ip resistor. +- powerdown-gpios: Reference to the GPIO connected to the pwdn pin, + if any. Active high with pull-down resistor. + +Endpoint node mandatory properties: +- remote-endpoint: A phandle to the bus receiver's endpoint node. + +Example: + + i2c1: i2c@fc028000 { + ov7740: camera@21 { + compatible = "ovti,ov7740"; + reg = <0x21>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sensor_power &pinctrl_sensor_reset>; + clocks = <&isc>; + clock-names = "xvclk"; + assigned-clocks = <&isc>; + assigned-clock-rates = <24000000>; + reset-gpios = <&pioA 43 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&pioA 44 GPIO_ACTIVE_HIGH>; + + port { + ov7740_0: endpoint { + remote-endpoint = <&isc_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov8856.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov8856.yaml new file mode 100644 index 000000000..d0f577363 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov8856.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2019 MediaTek Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov8856.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV8856 CMOS Sensor + +maintainers: + - Sakari Ailus <sakari.ailus@linux.intel.com> + +description: |- + The Omnivision OV8856 is a high performance, 1/4-inch, 8 megapixel, CMOS + image sensor that delivers 3264x2448 at 30fps. It provides full-frame, + sub-sampled, and windowed 10-bit MIPI images in various formats via the + Serial Camera Control Bus (SCCB) interface. This chip is programmable + through I2C and two-wire SCCB. The sensor output is available via CSI-2 + serial data output (up to 4-lane). + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov8856 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + description: + Input clock for the sensor. + items: + - const: xvclk + + clock-frequency: + description: + Frequency of the xvclk clock in Hertz. + deprecated: true + + dovdd-supply: + description: + Definition of the regulator used as interface power supply. + + avdd-supply: + description: + Definition of the regulator used as analog power supply. + + dvdd-supply: + description: + Definition of the regulator used as digital power supply. + + reset-gpios: + description: + The phandle and specifier for the GPIO that controls sensor reset. + This corresponds to the hardware pin XSHUTDOWN which is physically + active low. + + orientation: true + rotation: true + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - link-frequencies + +required: + - compatible + - reg + - clocks + - clock-names + - dovdd-supply + - avdd-supply + - dvdd-supply + - reset-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov8856: camera@10 { + compatible = "ovti,ov8856"; + reg = <0x10>; + + reset-gpios = <&pio 111 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&clk_24m_cam>; + + clocks = <&cam_osc>; + clock-names = "xvclk"; + + avdd-supply = <&mt6358_vcama2_reg>; + dvdd-supply = <&mt6358_vcamd_reg>; + dovdd-supply = <&mt6358_vcamio_reg>; + + port { + wcam_out: endpoint { + remote-endpoint = <&mipi_in_wcam>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov8858.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov8858.yaml new file mode 100644 index 000000000..491f2931e --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov8858.yaml @@ -0,0 +1,108 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov8858.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV8858 Image Sensor + +maintainers: + - Jacopo Mondi <jacopo.mondi@ideasonboard.com> + - Nicholas Roth <nicholas@rothemail.net> + +description: | + The OmniVision OV8858 is a color CMOS 8 Megapixels (3264x2448) image sensor + controlled through an I2C-compatible SCCB bus. The sensor transmits images + on a MIPI CSI-2 output interface with up to 4 data lanes. + +$ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: ovti,ov8858 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + description: XVCLK external clock + + clock-names: + const: xvclk + + dvdd-supply: + description: Digital Domain Power Supply + + avdd-supply: + description: Analog Domain Power Supply + + dovdd-supply: + description: I/O Domain Power Supply + + powerdown-gpios: + description: PWDNB powerdown GPIO (active low) + + reset-gpios: + maxItems: 1 + description: XSHUTDN reset GPIO (active low) + + port: + description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + +required: + - compatible + - reg + - clocks + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/pinctrl/rockchip.h> + #include <dt-bindings/clock/rk3399-cru.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov8858: camera@36 { + compatible = "ovti,ov8858"; + reg = <0x36>; + + clocks = <&cru SCLK_CIF_OUT>; + clock-names = "xvclk"; + assigned-clocks = <&cru SCLK_CIF_OUT>; + assigned-clock-rates = <24000000>; + + dovdd-supply = <&vcc1v8_dvp>; + + reset-gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&gpio2 RK_PB4 GPIO_ACTIVE_LOW>; + + port { + ucam_out: endpoint { + remote-endpoint = <&mipi_in_ucam>; + data-lanes = <1 2 3 4>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml new file mode 100644 index 000000000..320b9aacb --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml @@ -0,0 +1,108 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov8865.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV8865 Image Sensor + +maintainers: + - Paul Kocialkowski <paul.kocialkowski@bootlin.com> + +properties: + compatible: + const: ovti,ov8865 + + reg: + maxItems: 1 + + clocks: + items: + - description: EXTCLK Clock + + dvdd-supply: + description: Digital Domain Power Supply + + avdd-supply: + description: Analog Domain Power Supply + + dovdd-supply: + description: I/O Domain Power Supply + + powerdown-gpios: + maxItems: 1 + description: Power Down Pin GPIO Control (active low) + + reset-gpios: + maxItems: 1 + description: Reset Pin GPIO Control (active low) + + port: + description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + link-frequencies: true + + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - dvdd-supply + - avdd-supply + - dovdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/sun8i-a83t-ccu.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov8865: camera@36 { + compatible = "ovti,ov8865"; + reg = <0x36>; + + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + + clocks = <&ccu CLK_CSI_MCLK>; + + avdd-supply = <®_ov8865_avdd>; + dovdd-supply = <®_ov8865_dovdd>; + dvdd-supply = <®_ov8865_dvdd>; + + powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */ + reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */ + + port { + ov8865_out_mipi_csi2: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + + remote-endpoint = <&mipi_csi2_in_ov8865>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov9282.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov9282.yaml new file mode 100644 index 000000000..401c8613f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov9282.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2021 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov9282.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV9282 Sensor + +maintainers: + - Paul J. Murphy <paul.j.murphy@intel.com> + - Daniele Alessandrelli <daniele.alessandrelli@intel.com> + +description: + OV9282 sensor is an OmniVision black & white CMOS active pixel digital image + sensor with an active array size of 1296H x 816V. It is programmable through + I2C interface. The I2C client address is fixed to 0x60/0x70 as per sensor data + sheet. Image data is sent through MIPI CSI-2. + OV9281 has a different lens chief ray angle. + +properties: + compatible: + enum: + - ovti,ov9281 + - ovti,ov9282 + reg: + description: I2C address + maxItems: 1 + + clocks: + description: Clock frequency from 6 to 27MHz + maxItems: 1 + + reset-gpios: + description: Reference to the GPIO connected to the XCLR pin, if any. + maxItems: 1 + + avdd-supply: + description: Analog voltage supply, 2.8 volts + + dvdd-supply: + description: Digital core voltage supply, 1.2 volts + + dovdd-supply: + description: Digital I/O voltage supply, 1.8 volts + + port: + additionalProperties: false + $ref: /schemas/graph.yaml#/$defs/port-base + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: true + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@60 { + compatible = "ovti,ov9282"; + reg = <0x60>; + clocks = <&ov9282_clk>; + + port { + ov9282: endpoint { + remote-endpoint = <&cam>; + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <800000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov9650.txt b/Documentation/devicetree/bindings/media/i2c/ovti,ov9650.txt new file mode 100644 index 000000000..506dfc528 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov9650.txt @@ -0,0 +1,36 @@ +* Omnivision OV9650/OV9652 CMOS sensor + +Required Properties: +- compatible: shall be one of + "ovti,ov9650" + "ovti,ov9652" +- clocks: reference to the xvclk input clock. + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the resetb pin, if any. + Active is high. +- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any. + Active is high. + +The device node shall contain one 'port' child node with one child 'endpoint' +subnode for its digital output video port, in accordance with the video +interface bindings defined in Documentation/devicetree/bindings/media/ +video-interfaces.txt. + +Example: + +&i2c0 { + ov9650: camera@30 { + compatible = "ovti,ov9650"; + reg = <0x30>; + reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_HIGH>; + powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_HIGH>; + clocks = <&xclk>; + + port { + ov9650_0: endpoint { + remote-endpoint = <&vcap1_in0>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt b/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt new file mode 100644 index 000000000..4a3181a3d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt @@ -0,0 +1,19 @@ +* Panasonic AMG88xx + +The Panasonic family of AMG88xx Grid-Eye sensors allow recording +8x8 10Hz video which consists of thermal datapoints + +Required Properties: + - compatible : Must be "panasonic,amg88xx" + - reg : i2c address of the device + +Example: + + i2c0@1c22000 { + ... + amg88xx@69 { + compatible = "panasonic,amg88xx"; + reg = <0x69>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/rda,rda5807.yaml b/Documentation/devicetree/bindings/media/i2c/rda,rda5807.yaml new file mode 100644 index 000000000..34a05df78 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/rda,rda5807.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/rda,rda5807.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Unisoc Communications RDA5807 FM radio receiver + +maintainers: + - Paul Cercueil <paul@crapouillou.net> + +properties: + compatible: + enum: + - rda,rda5807 + + reg: + description: I2C address. + maxItems: 1 + + power-supply: true + + rda,lnan: + description: Use LNAN input port. + type: boolean + + rda,lnap: + description: Use LNAP input port. + type: boolean + + rda,analog-out: + description: Enable analog audio output. + type: boolean + + rda,i2s-out: + description: Enable I2S digital audio output. + type: boolean + + rda,lna-microamp: + description: LNA working current, in micro-amperes. + default: 2500 + enum: [1800, 2100, 2500, 3000] + +required: + - compatible + - reg + - power-supply + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + radio@11 { + compatible = "rda,rda5807"; + reg = <0x11>; + + power-supply = <&ldo6>; + + rda,lnan; + rda,lnap; + rda,analog-out; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/samsung,s5k3m5.yaml b/Documentation/devicetree/bindings/media/i2c/samsung,s5k3m5.yaml new file mode 100644 index 000000000..434f15f64 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/samsung,s5k3m5.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/samsung,s5k3m5.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5K3M5 Image Sensor + +description: + Samsung S5K3M5 (ISOCELL 3M5) image sensor is a 13MP image sensor. + The sensor is controlled over a serial camera control bus protocol, + the widest supported output image frame size is 4208x3120 at 30 frames + per second, data output format is RAW10 transferred over 4-lane + MIPI D-PHY interface. + +maintainers: + - Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: samsung,s5k3m5 + + reg: + maxItems: 1 + + clocks: + description: MCLK supply clock. + maxItems: 1 + + reset-gpios: + description: Active low GPIO connected to RESET pad of the sensor. + maxItems: 1 + + afvdd-supply: + description: Autofocus actuator voltage supply, 2.8-3.0 volts. + + vdda-supply: + description: Analogue voltage supply, 2.8 volts. + + vddd-supply: + description: Digital core voltage supply, 1.05 volts. + + vddio-supply: + description: Digital I/O voltage supply, 2.8 or 1.8 volts. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - link-frequencies + +required: + - compatible + - reg + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@10 { + compatible = "samsung,s5k3m5"; + reg = <0x10>; + clocks = <&camera_mclk 0>; + assigned-clocks = <&camera_mclk 0>; + assigned-clock-rates = <24000000>; + reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + vdda-supply = <&vreg_2p8>; + vddd-supply = <&vreg_1p05>; + vddio-supply = <&vreg_1p8>; + + port { + endpoint { + link-frequencies = /bits/ 64 <602500000>; + remote-endpoint = <&mipi_csi2_ep>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/samsung,s5k5baf.yaml b/Documentation/devicetree/bindings/media/i2c/samsung,s5k5baf.yaml new file mode 100644 index 000000000..4cb0f5aa1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/samsung,s5k5baf.yaml @@ -0,0 +1,105 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/samsung,s5k5baf.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5K5BAF UXGA 1/5" 2M CMOS Image Sensor with embedded SoC ISP + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + const: samsung,s5k5baf + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: mclk + + clock-frequency: + default: 24000000 + description: mclk clock frequency + deprecated: true + + rstn-gpios: + maxItems: 1 + description: RSTN pin + + stbyn-gpios: + maxItems: 1 + description: STDBYN pin + + vdda-supply: + description: Analog power supply 2.8V (2.6V to 3.0V) + + vddio-supply: + description: I/O power supply 1.8V (1.65V to 1.95V) or 2.8V (2.5V to 3.1V) + + vddreg-supply: + description: + Regulator input power supply 1.8V (1.7V to 1.9V) or 2.8V (2.6V to 3.0) + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + items: + - const: 1 + +required: + - compatible + - clocks + - clock-names + - rstn-gpios + - stbyn-gpios + - vdda-supply + - vddio-supply + - vddreg-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@2d { + compatible = "samsung,s5k5baf"; + reg = <0x2d>; + + clocks = <&camera 0>; + assigned-clocks = <&camera 0>; + assigned-clock-rates = <24000000>; + + clock-names = "mclk"; + rstn-gpios = <&gpl2 1 GPIO_ACTIVE_LOW>; + stbyn-gpios = <&gpl2 0 GPIO_ACTIVE_LOW>; + vdda-supply = <&cam_io_en_reg>; + vddio-supply = <&vtcam_reg>; + vddreg-supply = <&vt_core_15v_reg>; + + port { + endpoint { + remote-endpoint = <&csis1_ep>; + data-lanes = <1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/samsung,s5k6a3.yaml b/Documentation/devicetree/bindings/media/i2c/samsung,s5k6a3.yaml new file mode 100644 index 000000000..9df1e0f87 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/samsung,s5k6a3.yaml @@ -0,0 +1,102 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/samsung,s5k6a3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5K6A3(YX) raw image sensor + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +description: + S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data + interfaces and CCI (I2C compatible) control bus. + +properties: + compatible: + const: samsung,s5k6a3 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: extclk + + clock-frequency: + default: 24000000 + description: extclk clock frequency + deprecated: true + + gpios: + maxItems: 1 + description: GPIO connected to the RESET pin + + afvdd-supply: + description: AF (actuator) voltage supply + + svdda-supply: + description: Core voltage supply + + svddio-supply: + description: I/O voltage supply + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + items: + - const: 1 + +required: + - compatible + - clocks + - clock-names + - gpios + - afvdd-supply + - svdda-supply + - svddio-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@10 { + compatible = "samsung,s5k6a3"; + reg = <0x10>; + + clocks = <&camera 1>; + assigned-clocks = <&camera 1>; + assigned-clock-rates = <24000000>; + + clock-names = "extclk"; + gpios = <&gpm1 6 GPIO_ACTIVE_LOW>; + afvdd-supply = <&ldo19_reg>; + svdda-supply = <&cam_io_reg>; + svddio-supply = <&ldo19_reg>; + + port { + endpoint { + remote-endpoint = <&csis1_ep>; + data-lanes = <1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/samsung,s5kjn1.yaml b/Documentation/devicetree/bindings/media/i2c/samsung,s5kjn1.yaml new file mode 100644 index 000000000..8f368ae04 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/samsung,s5kjn1.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/samsung,s5kjn1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5KJN1 Image Sensor + +description: + Samsung S5KJN1 (ISOCELL JN1) image sensor is a 50MP image sensor. + The sensor is controlled over a serial camera control bus protocol, + the widest supported output image frame size is 8160x6144 at 10 frames + per second, data output format is RAW10 transferred over 4-lane + MIPI D-PHY interface. + +maintainers: + - Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: samsung,s5kjn1 + + reg: + maxItems: 1 + + clocks: + description: MCLK supply clock. + maxItems: 1 + + reset-gpios: + description: Active low GPIO connected to RESET pad of the sensor. + maxItems: 1 + + afvdd-supply: + description: Autofocus actuator voltage supply, 2.8-3.0 volts. + + vdda-supply: + description: Analogue voltage supply, 2.8 volts. + + vddd-supply: + description: Digital core voltage supply, 1.05 volts. + + vddio-supply: + description: Digital I/O voltage supply, 1.8 volts. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - link-frequencies + +required: + - compatible + - reg + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@56 { + compatible = "samsung,s5kjn1"; + reg = <0x56>; + clocks = <&camera_mclk 0>; + assigned-clocks = <&camera_mclk 0>; + assigned-clock-rates = <24000000>; + reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + vdda-supply = <&vreg_2p8>; + vddd-supply = <&vreg_1p05>; + vddio-supply = <&vreg_1p8>; + + port { + endpoint { + link-frequencies = /bits/ 64 <700000000>; + remote-endpoint = <&mipi_csi2_ep>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx111.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx111.yaml new file mode 100644 index 000000000..20f48d5e9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx111.yaml @@ -0,0 +1,105 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx111.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX111 8MP CMOS Digital Image Sensor + +maintainers: + - Svyatoslav Ryhel <clamor95@gmail.com> + +description: + IMX111 sensor is a Sony CMOS active pixel digital image sensor with an active + array size of 2464H x 3280V. It is programmable through I2C interface. Image + data is sent through MIPI CSI-2, through 1 or 2 lanes. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + - $ref: /schemas/nvmem/nvmem-consumer.yaml# + +properties: + compatible: + const: sony,imx111 + + reg: + maxItems: 1 + + clocks: + description: EXTCLK with possible frequency from 6 to 54 MHz + maxItems: 1 + + reset-gpios: + maxItems: 1 + + iovdd-supply: + description: Digital IO power supply (1.8V) + + dvdd-supply: + description: Digital power supply (1.2V) + + avdd-supply: + description: Analog power supply (2.7V) + + port: + additionalProperties: false + $ref: /schemas/graph.yaml#/$defs/port-base + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@10 { + compatible = "sony,imx111"; + reg = <0x10>; + + clocks = <&imx111_clk>; + + iovdd-supply = <&camera_vddio_1v8>; + dvdd-supply = <&camera_vddd_1v2>; + avdd-supply = <&camera_vdda_2v7>; + + orientation = <1>; + rotation = <90>; + + nvmem = <&eeprom>; + flash-leds = <&led>; + lens-focus = <&vcm>; + + reset-gpios = <&gpio 84 GPIO_ACTIVE_LOW>; + + port { + imx111_output: endpoint { + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <542400000>; + remote-endpoint = <&csi_input>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx214.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx214.yaml new file mode 100644 index 000000000..aea99ebf8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx214.yaml @@ -0,0 +1,128 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx214.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony 1/3.06-Inch 13.13MP CMOS Digital Image Sensor + +maintainers: + - Ricardo Ribalda <ribalda@kernel.org> + +description: | + The Sony IMX214 is a 1/3.06-inch CMOS active pixel digital image sensor with + an active array size of 4224H x 3200V. It is programmable through an I2C + interface. Image data is sent through MIPI CSI-2, through 2 or 4 lanes at a + maximum throughput of 1.2Gbps/lane. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: sony,imx214 + + reg: + enum: + - 0x10 + - 0x1a + + clocks: + description: Reference to the xclk clock. + maxItems: 1 + + clock-frequency: + description: Frequency of the xclk clock in Hz. + deprecated: true + + enable-gpios: + description: GPIO descriptor for the enable pin. + maxItems: 1 + + vdda-supply: + description: Chip analog regulator (2.7V). + + vddd-supply: + description: Chip digital core regulator (1.12V). + + vdddo-supply: + description: Chip digital IO regulator (1.8V). + + flash-leds: true + lens-focus: true + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + description: | + Video output port. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + anyOf: + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - enable-gpios + - vdda-supply + - vddd-supply + - vdddo-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera-sensor@1a { + compatible = "sony,imx214"; + reg = <0x1a>; + + clocks = <&camera_clk>; + assigned-clocks = <&camera_clk>; + assigned-clock-rates = <24000000>; + + enable-gpios = <&msmgpio 25 GPIO_ACTIVE_HIGH>; + + vdda-supply = <&pm8994_l17>; + vddd-supply = <&camera_vddd_1v12>; + vdddo-supply = <&pm8994_lvs1>; + + lens-focus = <&ad5820>; + + port { + imx214_ep: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <600000000>; + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx219.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx219.yaml new file mode 100644 index 000000000..38c3759bc --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx219.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx219.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor + +maintainers: + - Dave Stevenson <dave.stevenson@raspberrypi.com> + +description: |- + The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor + with an active array size of 3280H x 2464V. It is programmable through + I2C interface. The I2C address is fixed to 0x10 as per sensor data sheet. + Image data is sent through MIPI CSI-2, which is configured as either 2 or + 4 data lanes. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: sony,imx219 + + reg: + description: I2C device address + maxItems: 1 + + clocks: + maxItems: 1 + + VDIG-supply: + description: + Digital I/O voltage supply, 1.8 volts + + VANA-supply: + description: + Analog voltage supply, 2.8 volts + + VDDL-supply: + description: + Digital core voltage supply, 1.2 volts + + reset-gpios: + maxItems: 1 + description: |- + Reference to the GPIO connected to the xclr pin, if any. + Must be released (set high) after all supplies are applied. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: |- + The sensor supports either two-lane, or four-lane operation. + If this property is omitted four-lane operation is assumed. + For two-lane operation the property must be set to <1 2>. + items: + - const: 1 + - const: 2 + + clock-noncontinuous: true + link-frequencies: true + + required: + - link-frequencies + +required: + - compatible + - reg + - clocks + - VANA-supply + - VDIG-supply + - VDDL-supply + - port + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + imx219: sensor@10 { + compatible = "sony,imx219"; + reg = <0x10>; + clocks = <&imx219_clk>; + VANA-supply = <&imx219_vana>; /* 2.8v */ + VDIG-supply = <&imx219_vdig>; /* 1.8v */ + VDDL-supply = <&imx219_vddl>; /* 1.2v */ + + port { + imx219_0: endpoint { + remote-endpoint = <&csi1_ep>; + data-lanes = <1 2>; + clock-noncontinuous; + link-frequencies = /bits/ 64 <456000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx258.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx258.yaml new file mode 100644 index 000000000..d105bd357 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx258.yaml @@ -0,0 +1,135 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx258.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX258 13 Mpixel CMOS Digital Image Sensor + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +description: |- + IMX258 is a diagonal 5.867mm (Type 1/3.06) 13 Mega-pixel CMOS active pixel + type stacked image sensor with a square pixel array of size 4208 x 3120. It + is programmable through I2C interface. Image data is sent through MIPI + CSI-2. The sensor exists in two different models, a standard variant + (IMX258) and a variant with phase detection autofocus (IMX258-PDAF). + The camera module does not expose the model through registers, so the + exact model needs to be specified. + +$ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + enum: + - sony,imx258 + - sony,imx258-pdaf + + clocks: + description: + Clock frequency from 6 to 27 MHz. + maxItems: 1 + + reg: + maxItems: 1 + + reset-gpios: + description: |- + Reference to the GPIO connected to the XCLR pin, if any. + + vana-supply: + description: + Analog voltage (VANA) supply, 2.7 V + + vdig-supply: + description: + Digital I/O voltage (VDIG) supply, 1.2 V + + vif-supply: + description: + Interface voltage (VIF) supply, 1.8 V + + # See ../video-interfaces.txt for more details + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + - items: + - const: 1 + - const: 2 + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - port + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@6c { + compatible = "sony,imx258"; + reg = <0x6c>; + clocks = <&imx258_clk>; + + port { + endpoint { + remote-endpoint = <&csi1_ep>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <320000000>; + }; + }; + }; + }; + + /* Oscillator on the camera board */ + imx258_clk: clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <19200000>; + }; + + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@6c { + compatible = "sony,imx258"; + reg = <0x6c>; + clocks = <&imx258_clk>; + + port { + endpoint { + remote-endpoint = <&csi1_ep>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <633600000>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml new file mode 100644 index 000000000..b06a6e75b --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml @@ -0,0 +1,76 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx274.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony 1/2.5-Inch 8.51MP CMOS Digital Image Sensor + +maintainers: + - Leon Luo <leonl@leopardimaging.com> + +description: | + The Sony IMX274 is a 1/2.5-inch CMOS active pixel digital image sensor with an + active array size of 3864H x 2202V. It is programmable through I2C interface. + Image data is sent through MIPI CSI-2, which is configured as 4 lanes at 1440 + Mbps. + +properties: + compatible: + const: sony,imx274 + + reg: + const: 0x1a + + reset-gpios: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: inck + + vana-supply: + description: Sensor 2.8 V analog supply. + + vdig-supply: + description: Sensor 1.8 V digital core supply. + + vddl-supply: + description: Sensor digital IO 1.2 V supply. + + port: + $ref: /schemas/graph.yaml#/properties/port + +required: + - compatible + - reg + - clocks + - clock-names + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + imx274: camera-sensor@1a { + compatible = "sony,imx274"; + reg = <0x1a>; + clocks = <&imx274_clk>; + clock-names = "inck"; + reset-gpios = <&gpio_sensor 0 0>; + + port { + sensor_out: endpoint { + remote-endpoint = <&csiss_in>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx283.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx283.yaml new file mode 100644 index 000000000..e4f49f143 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx283.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2024 Ideas on Board Oy +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx283.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX283 Sensor + +maintainers: + - Kieran Bingham <kieran.bingham@ideasonboard.com> + - Umang Jain <umang.jain@ideasonboard.com> + +description: + IMX283 sensor is a Sony CMOS active pixel digital image sensor with an active + array size of 5472H x 3648V. It is programmable through I2C interface. The + I2C client address is fixed to 0x1a as per sensor data sheet. Image data is + sent through MIPI CSI-2. + +properties: + compatible: + const: sony,imx283 + + reg: + maxItems: 1 + + clocks: + description: Clock frequency from 6 to 24 MHz. + maxItems: 1 + + vadd-supply: + description: Analog power supply (2.9V) + + vdd1-supply: + description: Interface power supply (1.8V) + + vdd2-supply: + description: Digital power supply (1.2V) + + reset-gpios: + description: Sensor reset (XCLR) GPIO + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + anyOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@1a { + compatible = "sony,imx283"; + reg = <0x1a>; + clocks = <&imx283_clk>; + + assigned-clocks = <&imx283_clk>; + assigned-clock-parents = <&imx283_clk_parent>; + assigned-clock-rates = <12000000>; + + vadd-supply = <&camera_vadd_2v9>; + vdd1-supply = <&camera_vdd1_1v8>; + vdd2-supply = <&camera_vdd2_1v2>; + + port { + imx283: endpoint { + remote-endpoint = <&cam>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx290.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx290.yaml new file mode 100644 index 000000000..484039671 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx290.yaml @@ -0,0 +1,146 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx290.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX290 1/2.8-Inch CMOS Image Sensor + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: |- + The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with Square + Pixel, available in either mono or colour variants. It is programmable + through I2C and 4-wire interfaces. + + The sensor output is available via CMOS logic parallel SDR output, Low voltage + LVDS DDR output and CSI-2 serial data output. The CSI-2 bus is the default. + No bindings have been defined for the other busses. + + imx290lqr is the full model identifier for the colour variant. "sony,imx290" + is treated the same as this as it was the original compatible string. + imx290llr is the mono version of the sensor. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + oneOf: + - enum: + - sony,imx290lqr # Colour + - sony,imx290llr # Monochrome + - sony,imx327lqr # Colour + - sony,imx462lqr # Colour + - sony,imx462llr # Monochrome + - const: sony,imx290 + deprecated: true + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + description: Input clock (37.125 MHz or 74.25 MHz) + items: + - const: xclk + + clock-frequency: + description: Frequency of the xclk clock in Hz + deprecated: true + + vdda-supply: + description: Analog power supply (2.9V) + + vddd-supply: + description: Digital core power supply (1.2V) + + vdddo-supply: + description: Digital I/O power supply (1.8V) + + reset-gpios: + description: Sensor reset (XCLR) GPIO + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + description: | + Video output port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + anyOf: + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - vdda-supply + - vddd-supply + - vdddo-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + imx290: camera-sensor@1a { + compatible = "sony,imx290lqr"; + reg = <0x1a>; + + pinctrl-names = "default"; + pinctrl-0 = <&camera_rear_default>; + + clocks = <&gcc 90>; + clock-names = "xclk"; + assigned-clocks = <&clks 1>; + assigned-clock-rates = <37125000>; + + vdddo-supply = <&camera_vdddo_1v8>; + vdda-supply = <&camera_vdda_2v8>; + vddd-supply = <&camera_vddd_1v5>; + + reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>; + + port { + imx290_ep: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <222750000 148500000>; + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx296.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx296.yaml new file mode 100644 index 000000000..65ad9c100 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx296.yaml @@ -0,0 +1,106 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx296.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX296 1/2.8-Inch CMOS Image Sensor + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: |- + The Sony IMX296 is a 1/2.9-Inch active pixel type CMOS Solid-state image + sensor with square pixel array and 1.58 M effective pixels. This chip + features a global shutter with variable charge-integration time. It is + programmable through I2C and 4-wire interfaces. The sensor output is + available via CSI-2 serial data output (1 Lane). + +properties: + compatible: + enum: + - sony,imx296 + - sony,imx296ll + - sony,imx296lq + description: + The IMX296 sensor exists in two different models, a colour variant + (IMX296LQ) and a monochrome variant (IMX296LL). The device exposes the + model through registers, allowing for auto-detection with a common + "sony,imx296" compatible string. However, some camera modules disable the + ability to read the sensor model register, which disables this feature. + In those cases, the exact model needs to be specified as "sony,imx296ll" + or "sony,imx296lq". + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + description: Input clock (37.125 MHz, 54 MHz or 74.25 MHz) + items: + - const: inck + + avdd-supply: + description: Analog power supply (3.3V) + + dvdd-supply: + description: Digital power supply (1.2V) + + ovdd-supply: + description: Interface power supply (1.8V) + + reset-gpios: + description: Sensor reset (XCLR) GPIO + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/properties/port + +required: + - compatible + - reg + - clocks + - clock-names + - avdd-supply + - dvdd-supply + - ovdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + imx296: camera-sensor@1a { + compatible = "sony,imx296"; + reg = <0x1a>; + + pinctrl-names = "default"; + pinctrl-0 = <&camera_rear_default>; + + clocks = <&gcc 90>; + clock-names = "inck"; + + avdd-supply = <&camera_vdda_3v3>; + dvdd-supply = <&camera_vddd_1v2>; + ovdd-supply = <&camera_vddo_1v8>; + + reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>; + + port { + imx296_ep: endpoint { + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx334.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx334.yaml new file mode 100644 index 000000000..3842e5130 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx334.yaml @@ -0,0 +1,82 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2021 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx334.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX334 Sensor + +maintainers: + - Paul J. Murphy <paul.j.murphy@intel.com> + - Daniele Alessandrelli <daniele.alessandrelli@intel.com> + +description: + IMX334 sensor is a Sony CMOS active pixel digital image sensor with an active + array size of 3864H x 2202V. It is programmable through I2C interface. The + I2C client address is fixed to 0x1a as per sensor data sheet. Image data is + sent through MIPI CSI-2. + +properties: + compatible: + const: sony,imx334 + reg: + description: I2C address + maxItems: 1 + + clocks: + description: Clock frequency from 6 to 27 MHz, 37.125MHz, 74.25MHz + maxItems: 1 + + reset-gpios: + description: Reference to the GPIO connected to the XCLR pin, if any. + + port: + additionalProperties: false + $ref: /schemas/graph.yaml#/$defs/port-base + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: true + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@1a { + compatible = "sony,imx334"; + reg = <0x1a>; + clocks = <&imx334_clk>; + + port { + imx334: endpoint { + remote-endpoint = <&cam>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <891000000 445500000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx335.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx335.yaml new file mode 100644 index 000000000..80f879b6b --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx335.yaml @@ -0,0 +1,100 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2021 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx335.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX335 Sensor + +maintainers: + - Paul J. Murphy <paul.j.murphy@intel.com> + - Daniele Alessandrelli <daniele.alessandrelli@intel.com> + +description: + IMX335 sensor is a Sony CMOS active pixel digital image sensor with an active + array size of 2592H x 1944V. It is programmable through I2C interface. The + I2C client address is fixed to 0x1a as per sensor data sheet. Image data is + sent through MIPI CSI-2. + +properties: + compatible: + const: sony,imx335 + reg: + description: I2C address + maxItems: 1 + + clocks: + description: Clock frequency from 6 to 27 MHz, 37.125MHz, 74.25MHz + maxItems: 1 + + avdd-supply: + description: Analog power supply (2.9V) + + ovdd-supply: + description: Interface power supply (1.8V) + + dvdd-supply: + description: Digital power supply (1.2V) + + reset-gpios: + description: Reference to the GPIO connected to the XCLR pin, if any. + maxItems: 1 + + port: + additionalProperties: false + $ref: /schemas/graph.yaml#/$defs/port-base + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: true + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@1a { + compatible = "sony,imx335"; + reg = <0x1a>; + clocks = <&imx335_clk>; + + avdd-supply = <&camera_vdda_2v9>; + ovdd-supply = <&camera_vddo_1v8>; + dvdd-supply = <&camera_vddd_1v2>; + + reset-gpios = <&gpio 50 GPIO_ACTIVE_LOW>; + + port { + imx335: endpoint { + remote-endpoint = <&cam>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <594000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml new file mode 100644 index 000000000..6050d7e7d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml @@ -0,0 +1,111 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx355.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX355 Sensor + +maintainers: + - Richard Acayan <mailingradian@gmail.com> + +description: + The IMX355 sensor is a 3280x2464 image sensor, commonly found as the front + camera in smartphones. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: sony,imx355 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + avdd-supply: + description: Analog power supply. + + dvdd-supply: + description: Digital power supply. + + dovdd-supply: + description: Interface power supply. + + reset-gpios: + description: Reset GPIO (active low). + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 4 + maxItems: 4 + + required: + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - avdd-supply + - dvdd-supply + - dovdd-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,camcc-sdm845.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@1a { + compatible = "sony,imx355"; + reg = <0x1a>; + + clocks = <&camcc CAM_CC_MCLK2_CLK>; + + assigned-clocks = <&camcc CAM_CC_MCLK2_CLK>; + assigned-clock-rates = <24000000>; + + reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>; + + avdd-supply = <&cam_front_ldo>; + dvdd-supply = <&cam_front_ldo>; + dovdd-supply = <&cam_vio_ldo>; + + pinctrl-names = "default"; + pinctrl-0 = <&cam_front_default>; + + rotation = <270>; + orientation = <0>; + + port { + cam_front_endpoint: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + remote-endpoint = <&camss_endpoint1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx412.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx412.yaml new file mode 100644 index 000000000..5447ab076 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx412.yaml @@ -0,0 +1,94 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2021 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx412.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX412 Sensor + +maintainers: + - Paul J. Murphy <paul.j.murphy@intel.com> + - Daniele Alessandrelli <daniele.alessandrelli@intel.com> + +description: + IMX412 sensor is a Sony CMOS active pixel digital image sensor with an active + array size of 4072H x 3176V. It is programmable through I2C interface. The + I2C client address is fixed to 0x1a as per sensor data sheet. Image data is + sent through MIPI CSI-2. + +properties: + compatible: + enum: + - sony,imx412 + - sony,imx577 + reg: + description: I2C address + maxItems: 1 + + clocks: + description: Clock frequency 6MHz, 12MHz, 18MHz, 24MHz or 27MHz + maxItems: 1 + + dovdd-supply: + description: Interface power supply. + + avdd-supply: + description: Analog power supply. + + dvdd-supply: + description: Digital power supply. + + reset-gpios: + description: Reference to the GPIO connected to the XCLR pin, if any. + maxItems: 1 + + port: + additionalProperties: false + $ref: /schemas/graph.yaml#/$defs/port-base + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: true + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@1a { + compatible = "sony,imx412"; + reg = <0x1a>; + clocks = <&imx412_clk>; + + port { + imx412: endpoint { + remote-endpoint = <&cam>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <600000000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx415.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx415.yaml new file mode 100644 index 000000000..7c11e871d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx415.yaml @@ -0,0 +1,115 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx415.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX415 CMOS Image Sensor + +maintainers: + - Michael Riesch <michael.riesch@collabora.com> + +description: |- + The Sony IMX415 is a diagonal 6.4 mm (Type 1/2.8) CMOS active pixel type + solid-state image sensor with a square pixel array and 8.46 M effective + pixels. This chip operates with analog 2.9 V, digital 1.1 V, and interface + 1.8 V triple power supply, and has low power consumption. + The IMX415 is programmable through I2C interface. The sensor output is + available via CSI-2 serial data output (two or four lanes). + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: sony,imx415 + + reg: + maxItems: 1 + + clocks: + description: Input clock (24 MHz, 27 MHz, 37.125 MHz, 72 MHz or 74.25 MHz) + maxItems: 1 + + avdd-supply: + description: Analog power supply (2.9 V) + + dvdd-supply: + description: Digital power supply (1.1 V) + + ovdd-supply: + description: Interface power supply (1.8 V) + + reset-gpios: + description: Sensor reset (XCLR) GPIO + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - data-lanes + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - avdd-supply + - dvdd-supply + - ovdd-supply + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + imx415: camera-sensor@1a { + compatible = "sony,imx415"; + reg = <0x1a>; + avdd-supply = <&vcc2v9_cam>; + clocks = <&clock_cam>; + dvdd-supply = <&vcc1v1_cam>; + lens-focus = <&vcm>; + orientation = <2>; + ovdd-supply = <&vcc1v8_cam>; + reset-gpios = <&gpio_expander 14 GPIO_ACTIVE_LOW>; + rotation = <180>; + + port { + imx415_ep: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <445500000>; + remote-endpoint = <&mipi_in>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml new file mode 100644 index 000000000..4d40e75b4 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml @@ -0,0 +1,175 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/st,st-mipid02.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge + +maintainers: + - Benjamin Mugnier <benjamin.mugnier@foss.st.com> + - Sylvain Petinot <sylvain.petinot@foss.st.com> + +description: + MIPID02 has two CSI-2 input ports, only one of those ports can be + active at a time. Active port input stream will be de-serialized + and its content outputted through PARALLEL output port. + CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 + second input port is a single lane 800Mbps. Both ports support clock + and data lane polarity swap. First port also supports data lane swap. + PARALLEL output port has a maximum width of 12 bits. + Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, + RGB444, YUV420 8-bit, YUV422 8-bit and YUV420 10-bit. + +properties: + compatible: + const: st,st-mipid02 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: xclk + + VDDE-supply: + description: + Sensor digital IO supply. Must be 1.8 volts. + + VDDIN-supply: + description: + Sensor internal regulator supply. Must be 1.8 volts. + + reset-gpios: + description: + Reference to the GPIO connected to the xsdn pin, if any. + This is an active low signal to the mipid02. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 first input port + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: + Single-lane operation shall be <1> or <2> . + Dual-lane operation shall be <1 2> or <2 1> . + minItems: 1 + maxItems: 2 + + lane-polarities: + description: + Any lane can be inverted or not. + minItems: 1 + maxItems: 3 + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 second input port + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: + Single-lane operation shall be <1> or <2> . + maxItems: 1 + + lane-polarities: + description: + Any lane can be inverted or not. + maxItems: 1 + + required: + - data-lanes + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: Output port + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-width: + enum: [6, 7, 8, 10, 12] + + required: + - bus-width + + anyOf: + - required: + - port@0 + - required: + - port@1 + + required: + - port@2 + +additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - VDDE-supply + - VDDIN-supply + - ports + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + mipid02: csi2rx@14 { + compatible = "st,st-mipid02"; + reg = <0x14>; + clocks = <&clk_ext_camera_12>; + clock-names = "xclk"; + VDDE-supply = <&vdd>; + VDDIN-supply = <&vdd>; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + + ep0: endpoint { + data-lanes = <1 2>; + remote-endpoint = <&mipi_csi2_in>; + }; + }; + port@2 { + reg = <2>; + + ep2: endpoint { + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + remote-endpoint = <¶llel_out>; + }; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-vgxy61.yaml b/Documentation/devicetree/bindings/media/i2c/st,st-vgxy61.yaml new file mode 100644 index 000000000..8c28848b2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/st,st-vgxy61.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2022 STMicroelectronics SA. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/st,st-vgxy61.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics VGxy61 HDR Global Shutter Sensor Family + +maintainers: + - Benjamin Mugnier <benjamin.mugnier@foss.st.com> + - Sylvain Petinot <sylvain.petinot@foss.st.com> + +description: |- + STMicroelectronics VGxy61 family has a CSI-2 output port. CSI-2 output is a + quad lanes 800Mbps per lane. + Supported formats are RAW8, RAW10, RAW12, RAW14 and RAW16. + Following part number are supported + - VG5661 and VG6661 are 1.6 Mpx (1464 x 1104) monochrome and color sensors. + Maximum frame rate is 75 fps. + - VG5761 and VG6761 are 2.3 Mpx (1944 x 1204) monochrome and color sensors. + Maximum frame rate is 60 fps. + +properties: + compatible: + const: st,st-vgxy61 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + VCORE-supply: + description: + Sensor digital core supply. Must be 1.2 volts. + + VDDIO-supply: + description: + Sensor digital IO supply. Must be 1.8 volts. + + VANA-supply: + description: + Sensor analog supply. Must be 2.8 volts. + + reset-gpios: + description: + Reference to the GPIO connected to the reset pin, if any. + This is an active low signal to the vgxy61. + + st,strobe-gpios-polarity: + description: + Invert polarity of illuminator's lights strobe GPIOs. + These GPIOs directly drive the illuminator LEDs. + type: boolean + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: + CSI lanes to use + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + remote-endpoint: true + + required: + - data-lanes + +required: + - compatible + - clocks + - VCORE-supply + - VDDIO-supply + - VANA-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + vgxy61: csi2tx@10 { + compatible = "st,st-vgxy61"; + reg = <0x10>; + clocks = <&clk_ext_camera>; + VCORE-supply = <&v1v2>; + VDDIO-supply = <&v1v8>; + VANA-supply = <&v2v8>; + reset-gpios = <&mfxgpio 18 GPIO_ACTIVE_LOW>; + port { + ep0: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&mipi_csi2_out>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/st,vd55g1.yaml b/Documentation/devicetree/bindings/media/i2c/st,vd55g1.yaml new file mode 100644 index 000000000..060ac6829 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/st,vd55g1.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2025 STMicroelectronics SA. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/st,vd55g1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics VD55G1 Global Shutter Image Sensor + +maintainers: + - Benjamin Mugnier <benjamin.mugnier@foss.st.com> + - Sylvain Petinot <sylvain.petinot@foss.st.com> + +description: |- + The STMicroelectronics VD55G1 is a global shutter image sensor with an active + array size of 804H x 704V. It is programmable through I2C interface. The I2C + address is fixed to 0x10. + + Image data is sent through MIPI CSI-2, which is configured as only 1 data + lane. The sensor provides 4 GPIOS that can be used for external LED signal + (synchronized with sensor integration periods). + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + enum: + - st,vd55g1 + - st,vd65g4 + description: + VD55G1 is the monochrome variant, while VD65G4 is the color one. + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + vcore-supply: + description: Digital core power supply (1.15V) + + vddio-supply: + description: Digital IO power supply (1.8V) + + vana-supply: + description: Analog power supply (2.8V) + + reset-gpios: + description: Sensor reset active low GPIO (XSHUTDOWN) + maxItems: 1 + + st,leds: + description: + List sensor's GPIOs used to control strobe light sources during exposure + time. The numbers identify the sensor pin on which the illumination + system is connected. GPIOs are active-high. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 4 + items: + minimum: 0 + maximum: 3 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + items: + - const: 1 + + link-frequencies: + maxItems: 1 + items: + minimum: 125000000 + maximum: 600000000 + + lane-polarities: + minItems: 1 + maxItems: 2 + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - vcore-supply + - vddio-supply + - vana-supply + - reset-gpios + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera-sensor@10 { + compatible = "st,vd55g1"; + reg = <0x10>; + + clocks = <&camera_clk_12M>; + + vcore-supply = <&camera_vcore_v1v15>; + vddio-supply = <&camera_vddio_v1v8>; + vana-supply = <&camera_vana_v2v8>; + + reset-gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + st,leds = <2>; + + orientation = <2>; + rotation = <0>; + + port { + endpoint { + data-lanes = <1>; + link-frequencies = /bits/ 64 <600000000>; + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/st,vd56g3.yaml b/Documentation/devicetree/bindings/media/i2c/st,vd56g3.yaml new file mode 100644 index 000000000..c6673b853 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/st,vd56g3.yaml @@ -0,0 +1,139 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2024 STMicroelectronics SA. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/st,vd56g3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics VD56G3 Global Shutter Image Sensor + +maintainers: + - Benjamin Mugnier <benjamin.mugnier@foss.st.com> + - Sylvain Petinot <sylvain.petinot@foss.st.com> + +description: |- + The STMicroelectronics VD56G3 is a 1.5 M pixel global shutter image sensor + with an active array size of 1124 x 1364 (portrait orientation). It is + programmable through I2C, the address is fixed to 0x10. The sensor output is + available via CSI-2, which is configured as either 1 or 2 data lanes. The + sensor provides 8 GPIOS that can be used for external LED signal + (synchronized with sensor integration periods) + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + enum: + - st,vd56g3 + - st,vd66gy + description: + Two variants are availables; VD56G3 is a monochrome sensor while VD66GY + is a colour variant. + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + vcore-supply: + description: Digital core power supply (1.15V) + + vddio-supply: + description: Digital IO power supply (1.8V) + + vana-supply: + description: Analog power supply (2.8V) + + reset-gpios: + description: Sensor reset active low GPIO (XSHUTDOWN) + maxItems: 1 + + st,leds: + description: + List sensor's GPIOs used to control strobe light sources during exposure + time. The numbers identify the sensor pin on which the illumination system + is connected. GPIOs are active-high. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 2 + items: + enum: [1, 2] + + link-frequencies: + maxItems: 1 + items: + enum: [402000000, 750000000] + + lane-polarities: + minItems: 1 + maxItems: 3 + description: Any lane can be inverted or not. + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - clocks + - vcore-supply + - vddio-supply + - vana-supply + - reset-gpios + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera-sensor@10 { + compatible = "st,vd56g3"; + reg = <0x10>; + + clocks = <&camera_clk_12M>; + + vcore-supply = <&camera_vcore_v1v15>; + vddio-supply = <&camera_vddio_v1v8>; + vana-supply = <&camera_vana_v2v8>; + + reset-gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + st,leds = <6>; + + orientation = <2>; + rotation = <0>; + + port { + endpoint { + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <402000000>; + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/techwell,tw9900.yaml b/Documentation/devicetree/bindings/media/i2c/techwell,tw9900.yaml new file mode 100644 index 000000000..0592d0b9a --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/techwell,tw9900.yaml @@ -0,0 +1,136 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/techwell,tw9900.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Techwell TW9900 NTSC/PAL video decoder + +maintainers: + - Mehdi Djait <mehdi.djait@bootlin.com> + +description: + The tw9900 is a multi-standard video decoder, supporting NTSC, PAL standards + with auto-detection features. + +properties: + compatible: + const: techwell,tw9900 + + reg: + maxItems: 1 + + vdd-supply: + description: VDD power supply + + reset-gpios: + description: GPIO descriptor for the RESET input pin + maxItems: 1 + + powerdown-gpios: + description: GPIO descriptor for the POWERDOWN input pin + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: Analog input port + + properties: + endpoint@0: + $ref: /schemas/graph.yaml#/properties/endpoint + description: CVBS over MUX0 + + endpoint@1: + $ref: /schemas/graph.yaml#/properties/endpoint + description: CVBS over MUX1 + + endpoint@2: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Chroma over CIN0 and Y over MUX0 + + endpoint@3: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Chroma over CIN0 and Y over MUX1 + + oneOf: + - required: + - endpoint@0 + - required: + - endpoint@1 + - required: + - endpoint@2 + - required: + - endpoint@3 + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Video port for the decoder output. + + required: + - port@0 + - port@1 + +required: + - compatible + - ports + - reg + - vdd-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/display/sdtv-standards.h> + #include <dt-bindings/gpio/gpio.h> + + composite_connector { + compatible = "composite-video-connector"; + label = "tv"; + sdtv-standards = <(SDTV_STD_PAL | SDTV_STD_NTSC)>; + + port { + composite_to_tw9900: endpoint { + remote-endpoint = <&tw9900_to_composite>; + }; + }; + }; + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + video-decoder@44 { + compatible = "techwell,tw9900"; + reg = <0x44>; + + vdd-supply = <&tw9900_supply>; + reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0>; + tw9900_to_composite: endpoint@0 { + reg = <0>; + remote-endpoint = <&composite_to_tw9900>; + }; + }; + + port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&cif_in>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml b/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml new file mode 100644 index 000000000..bc339a737 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml @@ -0,0 +1,223 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2023 Ideas on Board +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/thine,thp7312.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: THine THP7312 + +maintainers: + - Paul Elder <paul.elder@@ideasonboard.com> + +description: + The THP7312 is a standalone ISP controlled over i2c, and is capable of + various image processing and correction functions, including 3A control. It + can be connected to CMOS image sensors from various vendors, supporting both + MIPI CSI-2 and parallel interfaces. It can also output on either MIPI CSI-2 + or parallel. The hardware is capable of transmitting and receiving MIPI + interleaved data streams with data types or multiple virtual channel + identifiers. + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: thine,thp7312 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + description: CLKI clock input + + thine,boot-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 1 + default: 1 + description: + Boot mode of the THP7312, reflecting the value of the BOOT[0] pin strap. + 0 is for the SPI/2-wire slave boot, 1 is for the SPI master boot (from + external flash ROM). + + reset-gpios: + maxItems: 1 + description: + Reference to the GPIO connected to the RESET_N pin, if any. + Must be released (set high) after all supplies are applied. + + vddcore-supply: + description: + 1.2V supply for core, PLL, MIPI rx and MIPI tx. + + vhtermrx-supply: + description: + Supply for input (RX). 1.8V for MIPI, or 1.8/2.8/3.3V for parallel. + + vddtx-supply: + description: + Supply for output (TX). 1.8V for MIPI, or 1.8/2.8/3.3V for parallel. + + vddhost-supply: + description: + Supply for host interface. 1.8V, 2.8V, or 3.3V. + + vddcmos-supply: + description: + Supply for sensor interface. 1.8V, 2.8V, or 3.3V. + + vddgpio-0-supply: + description: + Supply for GPIO_0. 1.8V, 2.8V, or 3.3V. + + vddgpio-1-supply: + description: + Supply for GPIO_1. 1.8V, 2.8V, or 3.3V. + + orientation: true + rotation: true + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + const: 4 # CSI-2 D-PHY + + data-lanes: + description: + This property is for lane reordering between the THP7312 and the + SoC. The sensor supports either two-lane, or four-lane operation. + If this property is omitted four-lane operation is assumed. For + two-lane operation the property must be set to <1 2>. + minItems: 2 + maxItems: 4 + items: + maximum: 4 + + sensors: + type: object + description: List of connected sensors + + properties: + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + patternProperties: + "^sensor@[01]$": + type: object + description: + Sensors connected to the first and second input, with one node per + sensor. + + properties: + thine,model: + $ref: /schemas/types.yaml#/definitions/string + description: + Model of the connected sensors. Must be a valid compatible string. + + reg: + description: THP7312 input port number + items: + - maximum: 1 + + data-lanes: + $ref: /schemas/media/video-interfaces.yaml#/properties/data-lanes + maxItems: 4 + description: + This property is for lane reordering between the THP7312 and the imaging + sensor that it is connected to. + + required: + - reg + - data-lanes + + additionalProperties: false + + required: + - "#address-cells" + - "#size-cells" + + additionalProperties: false + +required: + - compatible + - reg + - reset-gpios + - clocks + - vddcore-supply + - vhtermrx-supply + - vddtx-supply + - vddhost-supply + - vddcmos-supply + - vddgpio-0-supply + - vddgpio-1-supply + - sensors + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/video-interfaces.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@61 { + compatible = "thine,thp7312"; + reg = <0x61>; + + pinctrl-names = "default"; + pinctrl-0 = <&cam1_pins_default>; + + reset-gpios = <&pio 119 GPIO_ACTIVE_LOW>; + clocks = <&camera61_clk>; + + vddcore-supply = <&vsys_v4p2>; + vhtermrx-supply = <&vsys_v4p2>; + vddtx-supply = <&vsys_v4p2>; + vddhost-supply = <&vsys_v4p2>; + vddcmos-supply = <&vsys_v4p2>; + vddgpio-0-supply = <&vsys_v4p2>; + vddgpio-1-supply = <&vsys_v4p2>; + + orientation = <0>; + rotation = <0>; + + sensors { + #address-cells = <1>; + #size-cells = <0>; + + sensor@0 { + thine,model = "sony,imx258"; + reg = <0>; + + data-lanes = <4 1 3 2>; + }; + }; + + port { + thp7312_2_endpoint: endpoint { + remote-endpoint = <&mipi_thp7312_2>; + bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>; + data-lanes = <4 2 1 3>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ti,ds90ub913.yaml b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub913.yaml new file mode 100644 index 000000000..f6612bb0f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub913.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ti,ds90ub913.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DS90UB913 FPD-Link III Serializer + +maintainers: + - Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> + +description: + The TI DS90UB913 is an FPD-Link III video serializer for parallel video. + +properties: + compatible: + enum: + - ti,ds90ub913a-q1 + + '#gpio-cells': + const: 2 + description: + First cell is the GPO pin number, second cell is the flags. The GPO pin + number must be in range of [0, 3]. Note that GPOs 2 and 3 are not + available in external oscillator mode. + + gpio-controller: true + + clocks: + maxItems: 1 + description: + Reference clock connected to the CLKIN pin. + + clock-names: + items: + - const: clkin + + '#clock-cells': + const: 0 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: Parallel input port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + required: + - pclk-sample + + port@1: + $ref: /schemas/graph.yaml#/properties/port + unevaluatedProperties: false + description: FPD-Link III output port + + required: + - port@0 + - port@1 + + i2c: + $ref: /schemas/i2c/i2c-controller.yaml# + unevaluatedProperties: false + +required: + - compatible + - '#gpio-cells' + - gpio-controller + - '#clock-cells' + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + serializer { + compatible = "ti,ds90ub913a-q1"; + + gpio-controller; + #gpio-cells = <2>; + + clocks = <&clk_cam_48M>; + clock-names = "clkin"; + + #clock-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ub913_in: endpoint { + remote-endpoint = <&sensor_out>; + pclk-sample = <1>; + }; + }; + + port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&deser_fpd_in>; + }; + }; + }; + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@48 { + compatible = "aptina,mt9v111"; + reg = <0x48>; + + clocks = <&fixed_clock>; + + port { + sensor_out: endpoint { + remote-endpoint = <&ub913_in>; + }; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ti,ds90ub953.yaml b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub953.yaml new file mode 100644 index 000000000..2e129bf57 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub953.yaml @@ -0,0 +1,147 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ti,ds90ub953.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DS90UB953 FPD-Link III Serializer + +maintainers: + - Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> + +description: + The TI DS90UB953 is an FPD-Link III video serializer for MIPI CSI-2. + +properties: + compatible: + enum: + - ti,ds90ub953-q1 + - ti,ds90ub971-q1 + + '#gpio-cells': + const: 2 + description: + First cell is the GPIO pin number, second cell is the flags. The GPIO pin + number must be in range of [0, 3]. + + gpio-controller: true + + clocks: + maxItems: 1 + description: + Reference clock connected to the CLKIN pin. + + clock-names: + items: + - const: clkin + + '#clock-cells': + const: 0 + + reg: + maxItems: 1 + description: + The strap I2C address of the serializer. Can be used by the deserializer + to communicate over back-channel when the forward-channel is not yet + active. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 input port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/properties/port + unevaluatedProperties: false + description: FPD-Link III output port + + required: + - port@0 + - port@1 + + i2c: + $ref: /schemas/i2c/i2c-controller.yaml# + unevaluatedProperties: false + +required: + - compatible + - '#gpio-cells' + - gpio-controller + - '#clock-cells' + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + link { + #address-cells = <1>; + #size-cells = <0>; + + serializer@18 { + compatible = "ti,ds90ub953-q1"; + reg = <0x18>; + + gpio-controller; + #gpio-cells = <2>; + + #clock-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ub953_in: endpoint { + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&sensor_out>; + }; + }; + + port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&deser_fpd_in>; + }; + }; + }; + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@1a { + compatible = "sony,imx274"; + reg = <0x1a>; + + reset-gpios = <&serializer 0 GPIO_ACTIVE_LOW>; + + clocks = <&serializer>; + clock-names = "inck"; + + port { + sensor_out: endpoint { + remote-endpoint = <&ub953_in>; + }; + }; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml new file mode 100644 index 000000000..8e2b82d6d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml @@ -0,0 +1,450 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ti,ds90ub960.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DS90UB9XX Family FPD-Link Deserializer Hubs + +maintainers: + - Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> + +description: + The TI DS90UB9XX devices are FPD-Link video deserializers with I2C and GPIO + forwarding. + +properties: + compatible: + enum: + - ti,ds90ub954-q1 + - ti,ds90ub960-q1 + - ti,ds90ub9702-q1 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + description: + Reference clock connected to the REFCLK pin. + + clock-names: + items: + - const: refclk + + powerdown-gpios: + maxItems: 1 + description: + Specifier for the GPIO connected to the PDB pin. + + i2c-alias-pool: + minItems: 1 + maxItems: 32 + + links: + type: object + additionalProperties: false + + properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + ti,manual-strobe: + type: boolean + description: + Enable manual strobe position and EQ level + + patternProperties: + '^link@[0-3]$': + type: object + additionalProperties: false + properties: + reg: + description: The link number + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + i2c-alias: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The I2C address used for the serializer. Transactions to this + address on the I2C bus where the deserializer resides are + forwarded to the serializer. + + ti,rx-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # RAW10 + - 1 # RAW12 HF + - 2 # RAW12 LF + - 3 # CSI2 SYNC + - 4 # CSI2 NON-SYNC + description: + FPD-Link Input Mode. This should reflect the hardware and the + default mode of the connected device. + + ti,cdr-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # FPD-Link III + - 1 # FPD-Link IV + description: + FPD-Link CDR Mode. This should reflect the hardware and the + default mode of the connected device. + + ti,strobe-pos: + $ref: /schemas/types.yaml#/definitions/int32 + minimum: -13 + maximum: 13 + description: Manual strobe position + + ti,eq-level: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 14 + description: Manual EQ level + + patternProperties: + '^serializer(@[0-9a-f]+)*$': + type: object + description: FPD-Link Serializer node + + required: + - reg + - i2c-alias + - ti,rx-mode + + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Ports represent FPD-Link inputs to the deserializer and CSI TX outputs + from the deserializer. The number of ports is model-dependent. + +required: + - compatible + - reg + - clocks + - clock-names + - ports + +$defs: + FPDLink-input-port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: FPD-Link input + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + description: + Endpoint for FPD-Link port. If the RX mode for this port is RAW, + hsync-active and vsync-active must be defined. + + CSI2-output-port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 Output + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + link-frequencies: + maxItems: 1 + + required: + - data-lanes + - link-frequencies + +allOf: + - $ref: /schemas/i2c/i2c-atr.yaml# + - if: + properties: + compatible: + contains: + enum: + - ti,ds90ub960-q1 + - ti,ds90ub9702-q1 + then: + properties: + ports: + properties: + port@0: + $ref: '#/$defs/FPDLink-input-port' + description: FPD-Link input 0 + + port@1: + $ref: '#/$defs/FPDLink-input-port' + description: FPD-Link input 1 + + port@2: + $ref: '#/$defs/FPDLink-input-port' + description: FPD-Link input 2 + + port@3: + $ref: '#/$defs/FPDLink-input-port' + description: FPD-Link input 3 + + port@4: + $ref: '#/$defs/CSI2-output-port' + description: CSI-2 Output 0 + + port@5: + $ref: '#/$defs/CSI2-output-port' + description: CSI-2 Output 1 + + required: + - port@0 + - port@1 + - port@2 + - port@3 + - port@4 + - port@5 + + - if: + properties: + compatible: + contains: + const: ti,ds90ub954-q1 + then: + properties: + ports: + properties: + port@0: + $ref: '#/$defs/FPDLink-input-port' + description: FPD-Link input 0 + + port@1: + $ref: '#/$defs/FPDLink-input-port' + description: FPD-Link input 1 + + port@2: + $ref: '#/$defs/CSI2-output-port' + description: CSI-2 Output 0 + + required: + - port@0 + - port@1 + - port@2 + + links: + properties: + link@2: false + link@3: false + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + + deser@3d { + compatible = "ti,ds90ub960-q1"; + reg = <0x3d>; + + clock-names = "refclk"; + clocks = <&fixed_clock>; + + powerdown-gpios = <&pca9555 7 GPIO_ACTIVE_LOW>; + + i2c-alias-pool = <0x4a 0x4b 0x4c 0x4d 0x4e 0x4f>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* Port 0, Camera 0 */ + port@0 { + reg = <0>; + + ub960_fpd3_1_in: endpoint { + remote-endpoint = <&ub953_1_out>; + }; + }; + + /* Port 1, Camera 1 */ + port@1 { + reg = <1>; + + ub960_fpd3_2_in: endpoint { + remote-endpoint = <&ub913_2_out>; + hsync-active = <0>; + vsync-active = <1>; + }; + }; + + /* Port 2, unconnected */ + port@2 { + reg = <2>; + }; + + /* Port 3, unconnected */ + port@3 { + reg = <3>; + }; + + /* Port 4, CSI-2 TX */ + port@4 { + reg = <4>; + ds90ub960_0_csi_out: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <800000000>; + remote-endpoint = <&csi2_phy0>; + }; + }; + + /* Port 5, unconnected */ + port@5 { + reg = <5>; + }; + }; + + links { + #address-cells = <1>; + #size-cells = <0>; + + /* Link 0 has DS90UB953 serializer and IMX274 sensor */ + + link@0 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0>; + i2c-alias = <0x44>; + + ti,rx-mode = <3>; + + serializer1: serializer@30 { + compatible = "ti,ds90ub953-q1"; + reg = <0x30>; + + gpio-controller; + #gpio-cells = <2>; + + #clock-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ub953_1_in: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&sensor_1_out>; + }; + }; + + port@1 { + reg = <1>; + + ub953_1_out: endpoint { + remote-endpoint = <&ub960_fpd3_1_in>; + }; + }; + }; + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@1a { + compatible = "sony,imx274"; + reg = <0x1a>; + + clocks = <&serializer>; + clock-names = "inck"; + + reset-gpios = <&serializer1 0 GPIO_ACTIVE_LOW>; + + port { + sensor_1_out: endpoint { + remote-endpoint = <&ub953_1_in>; + }; + }; + }; + }; + }; + }; /* End of link@0 */ + + /* Link 1 has DS90UB913 serializer and MT9V111 sensor */ + + link@1 { + reg = <1>; + i2c-alias = <0x45>; + + ti,rx-mode = <0>; + + serializer2: serializer { + compatible = "ti,ds90ub913a-q1"; + + gpio-controller; + #gpio-cells = <2>; + + clocks = <&clk_cam_48M>; + clock-names = "clkin"; + + #clock-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ub913_2_in: endpoint { + remote-endpoint = <&sensor_2_out>; + pclk-sample = <1>; + }; + }; + + port@1 { + reg = <1>; + + ub913_2_out: endpoint { + remote-endpoint = <&ub960_fpd3_2_in>; + }; + }; + }; + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@48 { + compatible = "aptina,mt9v111"; + reg = <0x48>; + + clocks = <&serializer2>; + + port { + sensor_2_out: endpoint { + remote-endpoint = <&ub913_2_in>; + }; + }; + }; + }; + }; + }; /* End of link@1 */ + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/i2c/ti,ths8200.txt b/Documentation/devicetree/bindings/media/i2c/ti,ths8200.txt new file mode 100644 index 000000000..285f6ae7d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ti,ths8200.txt @@ -0,0 +1,19 @@ +* Texas Instruments THS8200 video encoder + +The ths8200 device is a digital to analog converter used in DVD players, video +recorders, set-top boxes. + +Required Properties : +- compatible : value must be "ti,ths8200" + +Example: + + i2c0@1c22000 { + ... + ... + ths8200@5c { + compatible = "ti,ths8200"; + reg = <0x5c>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ti,tvp514x.txt b/Documentation/devicetree/bindings/media/i2c/ti,tvp514x.txt new file mode 100644 index 000000000..46752cc71 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ti,tvp514x.txt @@ -0,0 +1,44 @@ +* Texas Instruments TVP514x video decoder + +The TVP5146/TVP5146m2/TVP5147/TVP5147m1 device is high quality, single-chip +digital video decoder that digitizes and decodes all popular baseband analog +video formats into digital video component. The tvp514x decoder supports analog- +to-digital (A/D) conversion of component RGB and YPbPr signals as well as A/D +conversion and decoding of NTSC, PAL and SECAM composite and S-video into +component YCbCr. + +Required Properties : +- compatible : value should be either one among the following + (a) "ti,tvp5146" for tvp5146 decoder. + (b) "ti,tvp5146m2" for tvp5146m2 decoder. + (c) "ti,tvp5147" for tvp5147 decoder. + (d) "ti,tvp5147m1" for tvp5147m1 decoder. + +- hsync-active: HSYNC Polarity configuration for endpoint. + +- vsync-active: VSYNC Polarity configuration for endpoint. + +- pclk-sample: Clock polarity of the endpoint. + +For further reading on port node refer to Documentation/devicetree/bindings/ +media/video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + tvp514x@5c { + compatible = "ti,tvp5146"; + reg = <0x5c>; + + port { + tvp514x_1: endpoint { + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + }; + }; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml b/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml new file mode 100644 index 000000000..382a29652 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ti,tvp5150.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments TVP5150 and TVP5151 video decoders + +maintainers: + - Frank Li <Frank.Li@nxp.com> + +description: + The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL + (and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV + with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats. + +properties: + compatible: + const: ti,tvp5150 + + reg: + maxItems: 1 + + pdn-gpios: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + sink port node, AIP1A + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + sink port node, AIP1B + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + source port node, Y-OUT + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + +required: + - compatible + - reg + - port@2 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/display/sdtv-standards.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + bridge@5c { + compatible = "ti,tvp5150"; + reg = <0x5c>; + pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + endpoint@0 { + reg = <0>; + remote-endpoint = <&composite0_to_tvp5150>; + }; + + endpoint@1 { + reg = <1>; + remote-endpoint = <&svideo_luma_to_tvp5150>; + }; + }; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + endpoint@0 { + reg = <0>; + remote-endpoint = <&composite1_to_tvp5150>; + }; + + endpoint@1 { + reg = <1>; + remote-endpoint = <&svideo_chroma_to_tvp5150>; + }; + }; + + port@2 { + reg = <2>; + + endpoint { + remote-endpoint = <&ccdc_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ti,tvp7002.txt b/Documentation/devicetree/bindings/media/i2c/ti,tvp7002.txt new file mode 100644 index 000000000..5f28b5d9a --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ti,tvp7002.txt @@ -0,0 +1,53 @@ +* Texas Instruments TV7002 video decoder + +The TVP7002 device supports digitizing of video and graphics signal in RGB and +YPbPr color space. + +Required Properties : +- compatible : Must be "ti,tvp7002" + +Optional Properties: +- hsync-active: HSYNC Polarity configuration for the bus. Default value when + this property is not specified is <0>. + +- vsync-active: VSYNC Polarity configuration for the bus. Default value when + this property is not specified is <0>. + +- pclk-sample: Clock polarity of the bus. Default value when this property is + not specified is <0>. + +- sync-on-green-active: Active state of Sync-on-green signal property of the + endpoint. + 0 = Normal Operation (Active Low, Default) + 1 = Inverted operation + +- field-even-active: Active-high Field ID output polarity control of the bus. + Under normal operation, the field ID output is set to logic 1 for an odd field + (field 1) and set to logic 0 for an even field (field 0). + 0 = Normal Operation (Active Low, Default) + 1 = FID output polarity inverted + +For further reading of port node refer Documentation/devicetree/bindings/media/ +video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + tvp7002@5c { + compatible = "ti,tvp7002"; + reg = <0x5c>; + + port { + tvp7002_1: endpoint { + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + sync-on-green-active = <1>; + field-even-active = <0>; + }; + }; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.yaml b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.yaml new file mode 100644 index 000000000..f0186ae87 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/toshiba,et8ek8.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Toshiba et8ek8 5MP sensor + +maintainers: + - Pavel Machek <pavel@ucw.cz> + - Sakari Ailus <sakari.ailus@iki.fi> + +description: + Toshiba et8ek8 5MP sensor is an image sensor found in Nokia N900 device + +allOf: + - $ref: /schemas/media/video-interface-devices.yaml# + +properties: + compatible: + const: toshiba,et8ek8 + + reg: + description: + I2C address (0x3e, or an alternative address) + maxItems: 1 + + vana-supply: + description: + Analogue voltage supply (VANA), 2.8 volts + + clocks: + maxItems: 1 + + reset-gpios: + description: + XSHUTDOWN GPIO. The XSHUTDOWN signal is active low. The sensor + is in hardware standby mode when the signal is in the low state. + maxItems: 1 + + flash-leds: + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + +required: + - compatible + - reg + - vana-supply + - clocks + - reset-gpios + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3e { + compatible = "toshiba,et8ek8"; + reg = <0x3e>; + vana-supply = <&vaux4>; + clocks = <&isp 0>; + assigned-clocks = <&isp 0>; + assigned-clock-rates = <9600000>; + reset-gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; + flash-leds = <&led>; + + port { + csi_cam1: endpoint { + remote-endpoint = <&csi_out1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,tc358743.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,tc358743.txt new file mode 100644 index 000000000..59102edcf --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,tc358743.txt @@ -0,0 +1,48 @@ +* Toshiba TC358743 HDMI-RX to MIPI CSI2-TX Bridge + +The Toshiba TC358743 HDMI-RX to MIPI CSI2-TX (H2C) is a bridge that converts +a HDMI stream to MIPI CSI-2 TX. It is programmable through I2C. + +Required Properties: + +- compatible: value should be "toshiba,tc358743" +- clocks, clock-names: should contain a phandle link to the reference clock + source, the clock input is named "refclk". + +Optional Properties: + +- reset-gpios: gpio phandle GPIO connected to the reset pin +- interrupts: GPIO connected to the interrupt pin +- data-lanes: should be <1 2 3 4> for four-lane operation, + or <1 2> for two-lane operation +- clock-lanes: should be <0> +- clock-noncontinuous: Presence of this boolean property decides whether the + MIPI CSI-2 clock is continuous or non-continuous. +- link-frequencies: List of allowed link frequencies in Hz. Each frequency is + expressed as a 64-bit big-endian integer. The frequency + is half of the bps per lane due to DDR transmission. + +For further information on the MIPI CSI-2 endpoint node properties, see +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + tc358743@f { + compatible = "toshiba,tc358743"; + reg = <0x0f>; + clocks = <&hdmi_osc>; + clock-names = "refclk"; + reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio2>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + + port { + tc358743_out: endpoint { + remote-endpoint = <&mipi_csi2_in>; + data-lanes = <1 2 3 4>; + clock-lanes = <0>; + clock-noncontinuous; + link-frequencies = /bits/ 64 <297000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.yaml b/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.yaml new file mode 100644 index 000000000..1c476b635 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.yaml @@ -0,0 +1,180 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/toshiba,tc358746.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Toshiba TC358746 Parallel to MIPI CSI2 Bridge + +maintainers: + - Marco Felsch <kernel@pengutronix.de> + +description: |- + The Toshiba TC358746 converts a parallel video stream into a MIPI CSI-2 + stream. The direction can be either parallel-in -> csi-out or csi-in -> + parallel-out The chip is programmable through I2C and SPI but the SPI + interface is only supported in parallel-in -> csi-out mode. + + Note that the current device tree bindings only support the + parallel-in -> csi-out path. + +properties: + compatible: + const: toshiba,tc358746 + + reg: + maxItems: 1 + + clocks: + description: + The phandle to the reference clock source. This corresponds to the + hardware pin REFCLK. + maxItems: 1 + + clock-names: + const: refclk + + "#clock-cells": + description: | + The bridge can act as clock provider for the sensor. To enable this + support #clock-cells must be specified. Attention if this feature is used + then the mclk rate must be at least: (2 * link-frequency) / 8 + `------------------´ ^ + internal PLL rate smallest possible + mclk-div + const: 0 + + clock-output-names: + description: + The clock name of the MCLK output, the default name is tc358746-mclk. + maxItems: 1 + + vddc-supply: + description: Digital core voltage supply, 1.2 volts + + vddio-supply: + description: Digital I/O voltage supply, 1.8 volts + + vddmipi-supply: + description: MIPI CSI phy voltage supply, 1.2 volts + + reset-gpios: + description: + The phandle and specifier for the GPIO that controls the chip reset. + This corresponds to the hardware pin RESX which is physically active low. + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: Input port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + hsync-active: true + vsync-active: true + bus-type: + enum: [ 5, 6 ] + + required: + - hsync-active + - vsync-active + - bus-type + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: Output port + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + clock-noncontinuous: true + link-frequencies: true + + required: + - data-lanes + - link-frequencies + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - clocks + - clock-names + - vddc-supply + - vddio-supply + - vddmipi-supply + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + csi-bridge@e { + compatible = "toshiba,tc358746"; + reg = <0xe>; + + clocks = <&refclk>; + clock-names = "refclk"; + + reset-gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + + vddc-supply = <&v1_2d>; + vddio-supply = <&v1_8d>; + vddmipi-supply = <&v1_2d>; + + /* sensor mclk provider */ + #clock-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* Input */ + port@0 { + reg = <0>; + tc358746_in: endpoint { + remote-endpoint = <&sensor_out>; + hsync-active = <0>; + vsync-active = <0>; + bus-type = <5>; + }; + }; + + /* Output */ + port@1 { + reg = <1>; + tc358746_out: endpoint { + remote-endpoint = <&mipi_csi2_in>; + data-lanes = <1 2>; + clock-noncontinuous; + link-frequencies = /bits/ 64 <216000000>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/img,e5010-jpeg-enc.yaml b/Documentation/devicetree/bindings/media/img,e5010-jpeg-enc.yaml new file mode 100644 index 000000000..085020cb9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/img,e5010-jpeg-enc.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/img,e5010-jpeg-enc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Imagination E5010 JPEG Encoder + +maintainers: + - Devarsh Thakkar <devarsht@ti.com> + +description: | + The E5010 is a JPEG encoder from Imagination Technologies implemented on + TI's AM62A SoC. It is capable of real time encoding of YUV420 and YUV422 + inputs to JPEG and M-JPEG. It supports baseline JPEG Encoding up to + 8Kx8K resolution. + +properties: + compatible: + oneOf: + - items: + - const: ti,am62a-jpeg-enc + - const: img,e5010-jpeg-enc + - const: img,e5010-jpeg-enc + + reg: + items: + - description: The E5010 core register region + - description: The E5010 mmu register region + + reg-names: + items: + - const: core + - const: mmu + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - reg-names + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/soc/ti,sci_pm_domain.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + jpeg-encoder@fd20000 { + compatible = "img,e5010-jpeg-enc"; + reg = <0x00 0xfd20000 0x00 0x100>, + <0x00 0xfd20200 0x00 0x200>; + reg-names = "core", "mmu"; + clocks = <&k3_clks 201 0>; + power-domains = <&k3_pds 201 TI_SCI_PD_EXCLUSIVE>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/img-ir-rev1.txt b/Documentation/devicetree/bindings/media/img-ir-rev1.txt new file mode 100644 index 000000000..ed9ec52b7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/img-ir-rev1.txt @@ -0,0 +1,34 @@ +* ImgTec Infrared (IR) decoder version 1 + +This binding is for Imagination Technologies' Infrared decoder block, +specifically major revision 1. + +Required properties: +- compatible: Should be "img,ir-rev1" +- reg: Physical base address of the controller and length of + memory mapped region. +- interrupts: The interrupt specifier to the cpu. + +Optional properties: +- clocks: List of clock specifiers as described in standard + clock bindings. + Up to 3 clocks may be specified in the following order: + 1st: Core clock (defaults to 32.768KHz if omitted). + 2nd: System side (fast) clock. + 3rd: Power modulation clock. +- clock-names: List of clock names corresponding to the clocks + specified in the clocks property. + Accepted clock names are: + "core": Core clock. + "sys": System clock. + "mod": Power modulation clock. + +Example: + + ir@2006200 { + compatible = "img,ir-rev1"; + reg = <0x02006200 0x100>; + interrupts = <29 4>; + clocks = <&clk_32khz>; + clock-names = "core"; + }; diff --git a/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.yaml b/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.yaml new file mode 100644 index 000000000..de3e483f1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright 2019,2020 Lubomir Rintel <lkundrak@v3.sk> +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/marvell,mmp2-ccic.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MMP2 camera host interface + +maintainers: + - Lubomir Rintel <lkundrak@v3.sk> + +properties: + $nodename: + pattern: '^camera@[a-f0-9]+$' + + compatible: + const: marvell,mmp2-ccic + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + power-domains: + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + hsync-active: true + vsync-active: true + pclk-sample: true + bus-type: true + + clocks: + minItems: 1 + items: + - description: AXI bus interface clock + - description: Peripheral clock + - description: Parallel video bus interface clock + + clock-names: + const: axi + + '#clock-cells': + const: 0 + + clock-output-names: + const: mclk + +required: + - compatible + - reg + - interrupts + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/marvell,mmp2.h> + #include <dt-bindings/media/video-interfaces.h> + #include <dt-bindings/power/marvell,mmp2.h> + + camera@d420a000 { + compatible = "marvell,mmp2-ccic"; + reg = <0xd420a000 0x800>; + interrupts = <42>; + clocks = <&soc_clocks MMP2_CLK_CCIC0>; + clock-names = "axi"; + #clock-cells = <0>; + clock-output-names = "mclk"; + power-domains = <&soc_clocks MMP3_POWER_DOMAIN_CAMERA>; + + port { + camera0_0: endpoint { + remote-endpoint = <&ov7670_0>; + bus-type = <MEDIA_BUS_TYPE_PARALLEL>; + hsync-active = <1>; /* Active high */ + vsync-active = <1>; /* Active high */ + pclk-sample = <0>; /* Falling */ + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/mediatek,mdp3-fg.yaml b/Documentation/devicetree/bindings/media/mediatek,mdp3-fg.yaml new file mode 100644 index 000000000..40fda59fa --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-fg.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,mdp3-fg.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek Media Data Path 3 Film Grain + +maintainers: + - Matthias Brugger <matthias.bgg@gmail.com> + - Moudy Ho <moudy.ho@mediatek.com> + +description: + Film Grain (FG) is a Media Data Path 3 (MDP3) component used to add + the film grain according to the AOMedia Video 1 (AV1) standard. + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt8195-mdp3-fg + - items: + - const: mediatek,mt8188-mdp3-fg + - const: mediatek,mt8195-mdp3-fg + + reg: + maxItems: 1 + + mediatek,gce-client-reg: + description: + The register of display function block to be set by gce. There are 4 arguments, + such as gce node, subsys id, offset and register size. The subsys id that is + mapping to the register of display function blocks is defined in the gce header + include/dt-bindings/gce/<chip>-gce.h of each chips. + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + items: + - description: phandle of GCE + - description: GCE subsys id + - description: register offset + - description: register size + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - mediatek,gce-client-reg + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8195-clk.h> + #include <dt-bindings/gce/mt8195-gce.h> + + display@14002000 { + compatible = "mediatek,mt8195-mdp3-fg"; + reg = <0x14002000 0x1000>; + mediatek,gce-client-reg = <&gce1 SUBSYS_1400XXXX 0x2000 0x1000>; + clocks = <&vppsys0 CLK_VPP0_MDP_FG>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek,mdp3-hdr.yaml b/Documentation/devicetree/bindings/media/mediatek,mdp3-hdr.yaml new file mode 100644 index 000000000..d9f926c20 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-hdr.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,mdp3-hdr.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek Media Data Path 3 HDR + +maintainers: + - Matthias Brugger <matthias.bgg@gmail.com> + - Moudy Ho <moudy.ho@mediatek.com> + +description: + A Media Data Path 3 (MDP3) component used to perform conversion from + High Dynamic Range (HDR) to Standard Dynamic Range (SDR). + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt8195-mdp3-hdr + - items: + - const: mediatek,mt8188-mdp3-hdr + - const: mediatek,mt8195-mdp3-hdr + + reg: + maxItems: 1 + + mediatek,gce-client-reg: + description: + The register of display function block to be set by gce. There are 4 arguments, + such as gce node, subsys id, offset and register size. The subsys id that is + mapping to the register of display function blocks is defined in the gce header + include/dt-bindings/gce/<chip>-gce.h of each chips. + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + items: + - description: phandle of GCE + - description: GCE subsys id + - description: register offset + - description: register size + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - mediatek,gce-client-reg + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8195-clk.h> + #include <dt-bindings/gce/mt8195-gce.h> + + display@14004000 { + compatible = "mediatek,mt8195-mdp3-hdr"; + reg = <0x14004000 0x1000>; + mediatek,gce-client-reg = <&gce1 SUBSYS_1400XXXX 0x4000 0x1000>; + clocks = <&vppsys0 CLK_VPP0_MDP_HDR>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek,mdp3-rdma.yaml b/Documentation/devicetree/bindings/media/mediatek,mdp3-rdma.yaml new file mode 100644 index 000000000..18603f6c5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-rdma.yaml @@ -0,0 +1,168 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,mdp3-rdma.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek Read Direct Memory Access + +maintainers: + - Matthias Brugger <matthias.bgg@gmail.com> + - Moudy Ho <moudy.ho@mediatek.com> + +description: | + MediaTek Read Direct Memory Access(RDMA) component used to do read DMA. + It contains one line buffer to store the sufficient pixel data, and + must be siblings to the central MMSYS_CONFIG node. + For a description of the MMSYS_CONFIG binding, see + Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.yaml + for details. + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt8183-mdp3-rdma + - mediatek,mt8188-mdp3-rdma + - mediatek,mt8195-mdp3-rdma + - mediatek,mt8195-vdo1-rdma + - items: + - const: mediatek,mt8188-vdo1-rdma + - const: mediatek,mt8195-vdo1-rdma + + reg: + maxItems: 1 + + mediatek,gce-client-reg: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + items: + - description: phandle of GCE + - description: GCE subsys id + - description: register offset + - description: register size + description: The register of client driver can be configured by gce with + 4 arguments defined in this property. Each GCE subsys id is mapping to + a client defined in the header include/dt-bindings/gce/<chip>-gce.h. + + mediatek,gce-events: + description: + The event id which is mapping to the specific hardware event signal + to gce. The event id is defined in the gce header + include/dt-bindings/gce/<chip>-gce.h of each chips. + $ref: /schemas/types.yaml#/definitions/uint32-array + + mediatek,scp: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to the System Control Processor (SCP) used for initializing + and stopping the MDP3, for sending frame data locations to the MDP3's + VPU and to install Inter-Processor Interrupt handlers to control + processing states. + + power-domains: + maxItems: 1 + + clocks: + items: + - description: RDMA clock + - description: RSZ clock + minItems: 1 + + iommus: + maxItems: 1 + + mboxes: + items: + - description: used for 1st data pipe from RDMA + - description: used for 2nd data pipe from RDMA + - description: used for 3rd data pipe from RDMA + - description: used for 4th data pipe from RDMA + - description: used for the data pipe from SPLIT + minItems: 1 + + interrupts: + maxItems: 1 + + '#dma-cells': + const: 1 + +required: + - compatible + - reg + - mediatek,gce-client-reg + - power-domains + - clocks + - iommus + - '#dma-cells' + +allOf: + - if: + properties: + compatible: + contains: + const: mediatek,mt8183-mdp3-rdma + + then: + properties: + clocks: + minItems: 2 + + mboxes: + minItems: 2 + + required: + - mboxes + - mediatek,gce-events + + - if: + properties: + compatible: + contains: + const: mediatek,mt8195-mdp3-rdma + + then: + properties: + clocks: + maxItems: 1 + + mboxes: + minItems: 5 + + required: + - mediatek,gce-events + + - if: + properties: + compatible: + contains: + const: mediatek,mt8195-vdo1-rdma + + then: + properties: + clocks: + maxItems: 1 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8183-clk.h> + #include <dt-bindings/gce/mt8183-gce.h> + #include <dt-bindings/power/mt8183-power.h> + #include <dt-bindings/memory/mt8183-larb-port.h> + + dma-controller@14001000 { + compatible = "mediatek,mt8183-mdp3-rdma"; + reg = <0x14001000 0x1000>; + mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x1000 0x1000>; + mediatek,gce-events = <CMDQ_EVENT_MDP_RDMA0_SOF>, + <CMDQ_EVENT_MDP_RDMA0_EOF>; + power-domains = <&spm MT8183_POWER_DOMAIN_DISP>; + clocks = <&mmsys CLK_MM_MDP_RDMA0>, + <&mmsys CLK_MM_MDP_RSZ1>; + iommus = <&iommu>; + mboxes = <&gce 20 CMDQ_THR_PRIO_LOWEST>, + <&gce 21 CMDQ_THR_PRIO_LOWEST>; + #dma-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek,mdp3-rsz.yaml b/Documentation/devicetree/bindings/media/mediatek,mdp3-rsz.yaml new file mode 100644 index 000000000..8124c39d7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-rsz.yaml @@ -0,0 +1,82 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,mdp3-rsz.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek Resizer + +maintainers: + - Matthias Brugger <matthias.bgg@gmail.com> + - Moudy Ho <moudy.ho@mediatek.com> + +description: | + One of Media Data Path 3 (MDP3) components used to do frame resizing. + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt8183-mdp3-rsz + - items: + - enum: + - mediatek,mt8188-mdp3-rsz + - mediatek,mt8195-mdp3-rsz + - const: mediatek,mt8183-mdp3-rsz + + reg: + maxItems: 1 + + mediatek,gce-client-reg: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + items: + - description: phandle of GCE + - description: GCE subsys id + - description: register offset + - description: register size + description: The register of client driver can be configured by gce with + 4 arguments defined in this property. Each GCE subsys id is mapping to + a client defined in the header include/dt-bindings/gce/<chip>-gce.h. + + mediatek,gce-events: + description: + The event id which is mapping to the specific hardware event signal + to gce. The event id is defined in the gce header + include/dt-bindings/gce/<chip>-gce.h of each chips. + $ref: /schemas/types.yaml#/definitions/uint32-array + + clocks: + minItems: 1 + +required: + - compatible + - reg + - mediatek,gce-client-reg + - mediatek,gce-events + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8183-clk.h> + #include <dt-bindings/gce/mt8183-gce.h> + + mdp3_rsz0: mdp3-rsz0@14003000 { + compatible = "mediatek,mt8183-mdp3-rsz"; + reg = <0x14003000 0x1000>; + mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x3000 0x1000>; + mediatek,gce-events = <CMDQ_EVENT_MDP_RSZ0_SOF>, + <CMDQ_EVENT_MDP_RSZ0_EOF>; + clocks = <&mmsys CLK_MM_MDP_RSZ0>; + }; + + mdp3_rsz1: mdp3-rsz1@14004000 { + compatible = "mediatek,mt8183-mdp3-rsz"; + reg = <0x14004000 0x1000>; + mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x4000 0x1000>; + mediatek,gce-events = <CMDQ_EVENT_MDP_RSZ1_SOF>, + <CMDQ_EVENT_MDP_RSZ1_EOF>; + clocks = <&mmsys CLK_MM_MDP_RSZ1>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek,mdp3-stitch.yaml b/Documentation/devicetree/bindings/media/mediatek,mdp3-stitch.yaml new file mode 100644 index 000000000..1d8e7e202 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-stitch.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,mdp3-stitch.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek Media Data Path 3 STITCH + +maintainers: + - Matthias Brugger <matthias.bgg@gmail.com> + - Moudy Ho <moudy.ho@mediatek.com> + +description: + One of Media Data Path 3 (MDP3) components used to combine multiple video frame + with overlapping fields of view to produce a segmented panorame. + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt8195-mdp3-stitch + - items: + - const: mediatek,mt8188-mdp3-stitch + - const: mediatek,mt8195-mdp3-stitch + + reg: + maxItems: 1 + + mediatek,gce-client-reg: + description: + The register of display function block to be set by gce. There are 4 arguments, + such as gce node, subsys id, offset and register size. The subsys id that is + mapping to the register of display function blocks is defined in the gce header + include/dt-bindings/gce/<chip>-gce.h of each chips. + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + items: + - description: phandle of GCE + - description: GCE subsys id + - description: register offset + - description: register size + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - mediatek,gce-client-reg + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8195-clk.h> + #include <dt-bindings/gce/mt8195-gce.h> + + display@14003000 { + compatible = "mediatek,mt8195-mdp3-stitch"; + reg = <0x14003000 0x1000>; + mediatek,gce-client-reg = <&gce1 SUBSYS_1400XXXX 0x3000 0x1000>; + clocks = <&vppsys0 CLK_VPP0_STITCH>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek,mdp3-tcc.yaml b/Documentation/devicetree/bindings/media/mediatek,mdp3-tcc.yaml new file mode 100644 index 000000000..6cff7c073 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-tcc.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,mdp3-tcc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek Media Data Path 3 Tone Curve Conversion + +maintainers: + - Matthias Brugger <matthias.bgg@gmail.com> + +description: + Tone Curve Conversion (TCC) is one of Media Profile Path 3 (MDP3) components. + It is used to handle the tone mapping of various gamma curves in order to + achieve HDR10 effects. This helps adapt the content to the color and + brightness range that standard display devices typically support. + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt8195-mdp3-tcc + - items: + - const: mediatek,mt8188-mdp3-tcc + - const: mediatek,mt8195-mdp3-tcc + + reg: + maxItems: 1 + + mediatek,gce-client-reg: + description: + The register of display function block to be set by gce. There are 4 arguments, + such as gce node, subsys id, offset and register size. The subsys id that is + mapping to the register of display function blocks is defined in the gce header + include/dt-bindings/gce/<chip>-gce.h of each chips. + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + items: + - description: phandle of GCE + - description: GCE subsys id + - description: register offset + - description: register size + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - mediatek,gce-client-reg + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8195-clk.h> + #include <dt-bindings/gce/mt8195-gce.h> + + display@1400b000 { + compatible = "mediatek,mt8195-mdp3-tcc"; + reg = <0x1400b000 0x1000>; + mediatek,gce-client-reg = <&gce1 SUBSYS_1400XXXX 0xb000 0x1000>; + clocks = <&vppsys0 CLK_VPP0_MDP_TCC>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek,mdp3-tdshp.yaml b/Documentation/devicetree/bindings/media/mediatek,mdp3-tdshp.yaml new file mode 100644 index 000000000..cdfa27324 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-tdshp.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,mdp3-tdshp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek Media Data Path 3 Two-Dimensional Sharpness + +maintainers: + - Matthias Brugger <matthias.bgg@gmail.com> + - Moudy Ho <moudy.ho@mediatek.com> + +description: + Two-Dimensional Sharpness (TDSHP) is a Media Profile Path 3 (MDP3) component + used to perform image edge sharpening and enhance vividness and contrast. + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt8195-mdp3-tdshp + - items: + - const: mediatek,mt8188-mdp3-tdshp + - const: mediatek,mt8195-mdp3-tdshp + + reg: + maxItems: 1 + + mediatek,gce-client-reg: + description: + The register of display function block to be set by gce. There are 4 arguments, + such as gce node, subsys id, offset and register size. The subsys id that is + mapping to the register of display function blocks is defined in the gce header + include/dt-bindings/gce/<chip>-gce.h of each chips. + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + items: + - description: phandle of GCE + - description: GCE subsys id + - description: register offset + - description: register size + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - mediatek,gce-client-reg + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8195-clk.h> + #include <dt-bindings/gce/mt8195-gce.h> + + display@14007000 { + compatible = "mediatek,mt8195-mdp3-tdshp"; + reg = <0x14007000 0x1000>; + mediatek,gce-client-reg = <&gce1 SUBSYS_1400XXXX 0x7000 0x1000>; + clocks = <&vppsys0 CLK_VPP0_MDP_TDSHP>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek,mdp3-wrot.yaml b/Documentation/devicetree/bindings/media/mediatek,mdp3-wrot.yaml new file mode 100644 index 000000000..b6269f4f9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-wrot.yaml @@ -0,0 +1,90 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,mdp3-wrot.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek Write DMA with Rotation + +maintainers: + - Matthias Brugger <matthias.bgg@gmail.com> + - Moudy Ho <moudy.ho@mediatek.com> + +description: | + One of Media Data Path 3 (MDP3) components used to write DMA with frame rotation. + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt8183-mdp3-wrot + - items: + - enum: + - mediatek,mt8188-mdp3-wrot + - mediatek,mt8195-mdp3-wrot + - const: mediatek,mt8183-mdp3-wrot + + reg: + maxItems: 1 + + mediatek,gce-client-reg: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + items: + - description: phandle of GCE + - description: GCE subsys id + - description: register offset + - description: register size + description: The register of client driver can be configured by gce with + 4 arguments defined in this property. Each GCE subsys id is mapping to + a client defined in the header include/dt-bindings/gce/<chip>-gce.h. + + mediatek,gce-events: + description: + The event id which is mapping to the specific hardware event signal + to gce. The event id is defined in the gce header + include/dt-bindings/gce/<chip>-gce.h of each chips. + $ref: /schemas/types.yaml#/definitions/uint32-array + + power-domains: + maxItems: 1 + + clocks: + minItems: 1 + + iommus: + maxItems: 1 + + '#dma-cells': + const: 1 + +required: + - compatible + - reg + - mediatek,gce-client-reg + - mediatek,gce-events + - power-domains + - clocks + - iommus + - '#dma-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8183-clk.h> + #include <dt-bindings/gce/mt8183-gce.h> + #include <dt-bindings/power/mt8183-power.h> + #include <dt-bindings/memory/mt8183-larb-port.h> + + dma-controller@14005000 { + compatible = "mediatek,mt8183-mdp3-wrot"; + reg = <0x14005000 0x1000>; + mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x5000 0x1000>; + mediatek,gce-events = <CMDQ_EVENT_MDP_WROT0_SOF>, + <CMDQ_EVENT_MDP_WROT0_EOF>; + power-domains = <&spm MT8183_POWER_DOMAIN_DISP>; + clocks = <&mmsys CLK_MM_MDP_WROT0>; + iommus = <&iommu>; + #dma-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek,mt7622-cir.yaml b/Documentation/devicetree/bindings/media/mediatek,mt7622-cir.yaml new file mode 100644 index 000000000..c01210e05 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,mt7622-cir.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,mt7622-cir.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek Consumer Infrared Receiver on-SoC Controller + +maintainers: + - Sean Wang <sean.wang@mediatek.com> + +allOf: + - $ref: rc.yaml# + +properties: + compatible: + enum: + - mediatek,mt7622-cir + - mediatek,mt7623-cir + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 2 + + clock-names: + items: + - const: clk + - const: bus + +required: + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/mt2701-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + ir@10013000 { + compatible = "mediatek,mt7623-cir"; + reg = <0x10013000 0x1000>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_IRRX>, <&topckgen CLK_TOP_AXI_SEL>; + clock-names = "clk", "bus"; + linux,rc-map-name = "rc-rc6-mce"; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek,mt8173-mdp.yaml b/Documentation/devicetree/bindings/media/mediatek,mt8173-mdp.yaml new file mode 100644 index 000000000..8ca33a733 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,mt8173-mdp.yaml @@ -0,0 +1,169 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,mt8173-mdp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek MT8173 Media Data Path + +maintainers: + - Ariel D'Alessandro <ariel.dalessandro@collabora.com> + +description: + Media Data Path is used for scaling and color space conversion. + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt8173-mdp-rdma + - mediatek,mt8173-mdp-rsz + - mediatek,mt8173-mdp-wdma + - mediatek,mt8173-mdp-wrot + - items: + - const: mediatek,mt8173-mdp-rdma + - const: mediatek,mt8173-mdp + + reg: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + + power-domains: + maxItems: 1 + + iommus: + maxItems: 1 + + mediatek,vpu: + $ref: /schemas/types.yaml#/definitions/phandle + description: + phandle to Mediatek Video Processor Unit for HW Codec encode/decode and + image processing. + +required: + - compatible + - reg + - clocks + - power-domains + +allOf: + - if: + properties: + compatible: + contains: + const: mediatek,mt8173-mdp-rdma + then: + properties: + clocks: + items: + - description: Main clock + - description: Mutex clock + else: + properties: + clocks: + items: + - description: Main clock + + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8173-mdp-rdma + - mediatek,mt8173-mdp-wdma + - mediatek,mt8173-mdp-wrot + then: + required: + - iommus + + - if: + properties: + compatible: + contains: + const: mediatek,mt8173-mdp + then: + required: + - mediatek,vpu + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8173-clk.h> + #include <dt-bindings/memory/mt8173-larb-port.h> + #include <dt-bindings/power/mt8173-power.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + mdp_rdma0: rdma@14001000 { + compatible = "mediatek,mt8173-mdp-rdma", + "mediatek,mt8173-mdp"; + reg = <0 0x14001000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RDMA0>, + <&mmsys CLK_MM_MUTEX_32K>; + power-domains = <&spm MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_RDMA0>; + mediatek,vpu = <&vpu>; + }; + + mdp_rdma1: rdma@14002000 { + compatible = "mediatek,mt8173-mdp-rdma"; + reg = <0 0x14002000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RDMA1>, + <&mmsys CLK_MM_MUTEX_32K>; + power-domains = <&spm MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_RDMA1>; + }; + + mdp_rsz0: rsz@14003000 { + compatible = "mediatek,mt8173-mdp-rsz"; + reg = <0 0x14003000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RSZ0>; + power-domains = <&spm MT8173_POWER_DOMAIN_MM>; + }; + + mdp_rsz1: rsz@14004000 { + compatible = "mediatek,mt8173-mdp-rsz"; + reg = <0 0x14004000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RSZ1>; + power-domains = <&spm MT8173_POWER_DOMAIN_MM>; + }; + + mdp_rsz2: rsz@14005000 { + compatible = "mediatek,mt8173-mdp-rsz"; + reg = <0 0x14005000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RSZ2>; + power-domains = <&spm MT8173_POWER_DOMAIN_MM>; + }; + + mdp_wdma0: wdma@14006000 { + compatible = "mediatek,mt8173-mdp-wdma"; + reg = <0 0x14006000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_WDMA>; + power-domains = <&spm MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_WDMA>; + }; + + mdp_wrot0: wrot@14007000 { + compatible = "mediatek,mt8173-mdp-wrot"; + reg = <0 0x14007000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_WROT0>; + power-domains = <&spm MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_WROT0>; + }; + + mdp_wrot1: wrot@14008000 { + compatible = "mediatek,mt8173-mdp-wrot"; + reg = <0 0x14008000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_WROT1>; + power-domains = <&spm MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_WROT1>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/mediatek,mt8173-vpu.yaml b/Documentation/devicetree/bindings/media/mediatek,mt8173-vpu.yaml new file mode 100644 index 000000000..8a47761f1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,mt8173-vpu.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,mt8173-vpu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek MT8173 Video Processor Unit + +maintainers: + - Ariel D'Alessandro <ariel.dalessandro@collabora.com> + +description: + Video Processor Unit is a HW video controller. It controls HW Codec including + H.264/VP8/VP9 Decode, H.264/VP8 Encode and Image Processor (scale/rotate/color + convert). + +properties: + compatible: + const: mediatek,mt8173-vpu + + reg: + maxItems: 2 + + reg-names: + items: + - const: tcm + - const: cfg_reg + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: main + + memory-region: + maxItems: 1 + +required: + - compatible + - reg + - reg-names + - interrupts + - clocks + - clock-names + - memory-region + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8173-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + vpu: vpu@10020000 { + compatible = "mediatek,mt8173-vpu"; + reg = <0 0x10020000 0 0x30000>, + <0 0x10050000 0 0x100>; + reg-names = "tcm", "cfg_reg"; + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topckgen CLK_TOP_SCP_SEL>; + clock-names = "main"; + memory-region = <&vpu_dma_reserved>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/mediatek,mt8195-jpegdec.yaml b/Documentation/devicetree/bindings/media/mediatek,mt8195-jpegdec.yaml new file mode 100644 index 000000000..e5448c60e --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,mt8195-jpegdec.yaml @@ -0,0 +1,161 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,mt8195-jpegdec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek JPEG Decoder + +maintainers: + - kyrie wu <kyrie.wu@mediatek.corp-partner.google.com> + +description: + MediaTek JPEG Decoder is the JPEG decode hardware present in MediaTek SoCs + +properties: + compatible: + const: mediatek,mt8195-jpgdec + + power-domains: + maxItems: 1 + + iommus: + maxItems: 6 + description: + Points to the respective IOMMU block with master port as argument, see + Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml for details. + Ports are according to the HW. + + "#address-cells": + const: 2 + + "#size-cells": + const: 2 + + ranges: true + +# Required child node: +patternProperties: + "^jpgdec@[0-9a-f]+$": + type: object + description: + The jpeg decoder hardware device node which should be added as subnodes to + the main jpeg node. + + properties: + compatible: + const: mediatek,mt8195-jpgdec-hw + + reg: + maxItems: 1 + + iommus: + minItems: 1 + maxItems: 32 + description: + List of the hardware port in respective IOMMU block for current Socs. + Refer to bindings/iommu/mediatek,iommu.yaml. + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: jpgdec + + power-domains: + maxItems: 1 + + required: + - compatible + - reg + - iommus + - interrupts + - clocks + - clock-names + - power-domains + + additionalProperties: false + +required: + - compatible + - power-domains + - iommus + - ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/memory/mt8195-memory-port.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/mt8195-clk.h> + #include <dt-bindings/power/mt8195-power.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + jpgdec-master { + compatible = "mediatek,mt8195-jpgdec"; + power-domains = <&spm MT8195_POWER_DOMAIN_VDEC1>; + iommus = <&iommu_vpp M4U_PORT_L19_JPGDEC_WDMA0>, + <&iommu_vpp M4U_PORT_L19_JPGDEC_BSDMA0>, + <&iommu_vpp M4U_PORT_L19_JPGDEC_WDMA1>, + <&iommu_vpp M4U_PORT_L19_JPGDEC_BSDMA1>, + <&iommu_vpp M4U_PORT_L19_JPGDEC_BUFF_OFFSET1>, + <&iommu_vpp M4U_PORT_L19_JPGDEC_BUFF_OFFSET0>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + jpgdec@1a040000 { + compatible = "mediatek,mt8195-jpgdec-hw"; + reg = <0 0x1a040000 0 0x10000>;/* JPGDEC_C0 */ + iommus = <&iommu_vdo M4U_PORT_L19_JPGDEC_WDMA0>, + <&iommu_vdo M4U_PORT_L19_JPGDEC_BSDMA0>, + <&iommu_vdo M4U_PORT_L19_JPGDEC_WDMA1>, + <&iommu_vdo M4U_PORT_L19_JPGDEC_BSDMA1>, + <&iommu_vdo M4U_PORT_L19_JPGDEC_BUFF_OFFSET1>, + <&iommu_vdo M4U_PORT_L19_JPGDEC_BUFF_OFFSET0>; + interrupts = <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&vencsys CLK_VENC_JPGDEC>; + clock-names = "jpgdec"; + power-domains = <&spm MT8195_POWER_DOMAIN_VDEC0>; + }; + + jpgdec@1a050000 { + compatible = "mediatek,mt8195-jpgdec-hw"; + reg = <0 0x1a050000 0 0x10000>;/* JPGDEC_C1 */ + iommus = <&iommu_vdo M4U_PORT_L19_JPGDEC_WDMA0>, + <&iommu_vdo M4U_PORT_L19_JPGDEC_BSDMA0>, + <&iommu_vdo M4U_PORT_L19_JPGDEC_WDMA1>, + <&iommu_vdo M4U_PORT_L19_JPGDEC_BSDMA1>, + <&iommu_vdo M4U_PORT_L19_JPGDEC_BUFF_OFFSET1>, + <&iommu_vdo M4U_PORT_L19_JPGDEC_BUFF_OFFSET0>; + interrupts = <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&vencsys CLK_VENC_JPGDEC_C1>; + clock-names = "jpgdec"; + power-domains = <&spm MT8195_POWER_DOMAIN_VDEC1>; + }; + + jpgdec@1b040000 { + compatible = "mediatek,mt8195-jpgdec-hw"; + reg = <0 0x1b040000 0 0x10000>;/* JPGDEC_C2 */ + iommus = <&iommu_vpp M4U_PORT_L20_JPGDEC_WDMA0>, + <&iommu_vpp M4U_PORT_L20_JPGDEC_BSDMA0>, + <&iommu_vpp M4U_PORT_L20_JPGDEC_WDMA1>, + <&iommu_vpp M4U_PORT_L20_JPGDEC_BSDMA1>, + <&iommu_vpp M4U_PORT_L20_JPGDEC_BUFF_OFFSET1>, + <&iommu_vpp M4U_PORT_L20_JPGDEC_BUFF_OFFSET0>; + interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&vencsys_core1 CLK_VENC_CORE1_JPGDEC>; + clock-names = "jpgdec"; + power-domains = <&spm MT8195_POWER_DOMAIN_VDEC2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek,mt8195-jpegenc.yaml b/Documentation/devicetree/bindings/media/mediatek,mt8195-jpegenc.yaml new file mode 100644 index 000000000..596186497 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,mt8195-jpegenc.yaml @@ -0,0 +1,140 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,mt8195-jpegenc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek JPEG Encoder + +maintainers: + - kyrie wu <kyrie.wu@mediatek.corp-partner.google.com> + +description: + MediaTek JPEG Encoder is the JPEG encode hardware present in MediaTek SoCs + +properties: + compatible: + const: mediatek,mt8195-jpgenc + + power-domains: + maxItems: 1 + + iommus: + maxItems: 4 + description: + Points to the respective IOMMU block with master port as argument, see + Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml for details. + Ports are according to the HW. + + "#address-cells": + const: 2 + + "#size-cells": + const: 2 + + ranges: true + +# Required child node: +patternProperties: + "^jpgenc@[0-9a-f]+$": + type: object + description: + The jpeg encoder hardware device node which should be added as subnodes to + the main jpeg node. + + properties: + compatible: + const: mediatek,mt8195-jpgenc-hw + + reg: + maxItems: 1 + + iommus: + minItems: 1 + maxItems: 32 + description: + List of the hardware port in respective IOMMU block for current Socs. + Refer to bindings/iommu/mediatek,iommu.yaml. + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: jpgenc + + power-domains: + maxItems: 1 + + required: + - compatible + - reg + - iommus + - interrupts + - clocks + - clock-names + - power-domains + + additionalProperties: false + +required: + - compatible + - power-domains + - iommus + - ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/memory/mt8195-memory-port.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/mt8195-clk.h> + #include <dt-bindings/power/mt8195-power.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + jpgenc-master { + compatible = "mediatek,mt8195-jpgenc"; + power-domains = <&spm MT8195_POWER_DOMAIN_VENC_CORE1>; + iommus = <&iommu_vpp M4U_PORT_L20_JPGENC_Y_RDMA>, + <&iommu_vpp M4U_PORT_L20_JPGENC_C_RDMA>, + <&iommu_vpp M4U_PORT_L20_JPGENC_Q_TABLE>, + <&iommu_vpp M4U_PORT_L20_JPGENC_BSDMA>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + jpgenc@1a030000 { + compatible = "mediatek,mt8195-jpgenc-hw"; + reg = <0 0x1a030000 0 0x10000>; + iommus = <&iommu_vdo M4U_PORT_L19_JPGENC_Y_RDMA>, + <&iommu_vdo M4U_PORT_L19_JPGENC_C_RDMA>, + <&iommu_vdo M4U_PORT_L19_JPGENC_Q_TABLE>, + <&iommu_vdo M4U_PORT_L19_JPGENC_BSDMA>; + interrupts = <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&vencsys CLK_VENC_JPGENC>; + clock-names = "jpgenc"; + power-domains = <&spm MT8195_POWER_DOMAIN_VENC>; + }; + + jpgenc@1b030000 { + compatible = "mediatek,mt8195-jpgenc-hw"; + reg = <0 0x1b030000 0 0x10000>; + iommus = <&iommu_vpp M4U_PORT_L20_JPGENC_Y_RDMA>, + <&iommu_vpp M4U_PORT_L20_JPGENC_C_RDMA>, + <&iommu_vpp M4U_PORT_L20_JPGENC_Q_TABLE>, + <&iommu_vpp M4U_PORT_L20_JPGENC_BSDMA>; + interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&vencsys_core1 CLK_VENC_CORE1_JPGENC>; + clock-names = "jpgenc"; + power-domains = <&spm MT8195_POWER_DOMAIN_VENC_CORE1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek,vcodec-decoder.yaml b/Documentation/devicetree/bindings/media/mediatek,vcodec-decoder.yaml new file mode 100644 index 000000000..d726d141a --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,vcodec-decoder.yaml @@ -0,0 +1,198 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,vcodec-decoder.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek Video Decode Accelerator + +maintainers: + - Yunfei Dong <yunfei.dong@mediatek.com> + +description: |+ + Mediatek Video Decode is the video decode hardware present in Mediatek + SoCs which supports high resolution decoding functionalities. + +properties: + compatible: + enum: + - mediatek,mt8173-vcodec-dec + - mediatek,mt8183-vcodec-dec + + reg: + minItems: 11 + maxItems: 11 + + reg-names: + items: + - const: misc + - const: ld + - const: top + - const: cm + - const: ad + - const: av + - const: pp + - const: hwd + - const: hwq + - const: hwb + - const: hwg + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 8 + + clock-names: + minItems: 1 + maxItems: 8 + + assigned-clocks: true + + assigned-clock-parents: true + + assigned-clock-rates: true + + power-domains: + maxItems: 1 + + iommus: + minItems: 1 + maxItems: 32 + description: | + List of the hardware port in respective IOMMU block for current Socs. + Refer to bindings/iommu/mediatek,iommu.yaml. + + mediatek,vpu: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Describes point to vpu. + + mediatek,scp: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Describes point to scp. + + mediatek,vdecsys: + $ref: /schemas/types.yaml#/definitions/phandle + description: Phandle to the vdecsys syscon node. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - iommus + - mediatek,vdecsys + +allOf: + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8183-vcodec-dec + + then: + required: + - mediatek,scp + + properties: + clocks: + minItems: 1 + maxItems: 1 + + clock-names: + items: + - const: vdec + + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8173-vcodec-dec + + then: + required: + - mediatek,vpu + + properties: + clocks: + minItems: 8 + maxItems: 8 + + clock-names: + items: + - const: vcodecpll + - const: univpll_d2 + - const: clk_cci400_sel + - const: vdec_sel + - const: vdecpll + - const: vencpll + - const: venc_lt_sel + - const: vdec_bus_clk_src + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/mt8173-clk.h> + #include <dt-bindings/memory/mt8173-larb-port.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/power/mt8173-power.h> + + vcodec_dec: vcodec@16020000 { + compatible = "mediatek,mt8173-vcodec-dec"; + reg = <0x16020000 0x1000>, /*VDEC_MISC*/ + <0x16021000 0x800>, /*VDEC_LD*/ + <0x16021800 0x800>, /*VDEC_TOP*/ + <0x16022000 0x1000>, /*VDEC_CM*/ + <0x16023000 0x1000>, /*VDEC_AD*/ + <0x16024000 0x1000>, /*VDEC_AV*/ + <0x16025000 0x1000>, /*VDEC_PP*/ + <0x16026800 0x800>, /*VP8_VD*/ + <0x16027000 0x800>, /*VP6_VD*/ + <0x16027800 0x800>, /*VP8_VL*/ + <0x16028400 0x400>; /*VP9_VD*/ + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_LOW>; + iommus = <&iommu M4U_PORT_HW_VDEC_MC_EXT>, + <&iommu M4U_PORT_HW_VDEC_PP_EXT>, + <&iommu M4U_PORT_HW_VDEC_AVC_MV_EXT>, + <&iommu M4U_PORT_HW_VDEC_PRED_RD_EXT>, + <&iommu M4U_PORT_HW_VDEC_PRED_WR_EXT>, + <&iommu M4U_PORT_HW_VDEC_UFO_EXT>, + <&iommu M4U_PORT_HW_VDEC_VLD_EXT>, + <&iommu M4U_PORT_HW_VDEC_VLD2_EXT>; + mediatek,vpu = <&vpu>; + mediatek,vdecsys = <&vdecsys>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_VDEC>; + clocks = <&apmixedsys CLK_APMIXED_VCODECPLL>, + <&topckgen CLK_TOP_UNIVPLL_D2>, + <&topckgen CLK_TOP_CCI400_SEL>, + <&topckgen CLK_TOP_VDEC_SEL>, + <&topckgen CLK_TOP_VCODECPLL>, + <&apmixedsys CLK_APMIXED_VENCPLL>, + <&topckgen CLK_TOP_VENC_LT_SEL>, + <&topckgen CLK_TOP_VCODECPLL_370P5>; + clock-names = "vcodecpll", + "univpll_d2", + "clk_cci400_sel", + "vdec_sel", + "vdecpll", + "vencpll", + "venc_lt_sel", + "vdec_bus_clk_src"; + assigned-clocks = <&topckgen CLK_TOP_VENC_LT_SEL>, + <&topckgen CLK_TOP_CCI400_SEL>, + <&topckgen CLK_TOP_VDEC_SEL>, + <&apmixedsys CLK_APMIXED_VCODECPLL>, + <&apmixedsys CLK_APMIXED_VENCPLL>; + assigned-clock-parents = <&topckgen CLK_TOP_VCODECPLL_370P5>, + <&topckgen CLK_TOP_UNIVPLL_D2>, + <&topckgen CLK_TOP_VCODECPLL>; + assigned-clock-rates = <0>, <0>, <0>, <1482000000>, <800000000>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek,vcodec-encoder.yaml b/Documentation/devicetree/bindings/media/mediatek,vcodec-encoder.yaml new file mode 100644 index 000000000..4505e6687 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,vcodec-encoder.yaml @@ -0,0 +1,179 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,vcodec-encoder.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek Video Encode Accelerator + +maintainers: + - Yunfei Dong <yunfei.dong@mediatek.com> + +description: |+ + Mediatek Video Encode is the video encode hardware present in Mediatek + SoCs which supports high resolution encoding functionalities. + +properties: + compatible: + oneOf: + - items: + - enum: + - mediatek,mt8173-vcodec-enc-vp8 + - mediatek,mt8173-vcodec-enc + - mediatek,mt8183-vcodec-enc + - mediatek,mt8188-vcodec-enc + - mediatek,mt8192-vcodec-enc + - mediatek,mt8195-vcodec-enc + - items: + - const: mediatek,mt8186-vcodec-enc + - const: mediatek,mt8183-vcodec-enc + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 5 + + clock-names: + minItems: 1 + maxItems: 5 + + iommus: + minItems: 1 + maxItems: 32 + description: | + List of the hardware port in respective IOMMU block for current Socs. + Refer to bindings/iommu/mediatek,iommu.yaml. + + mediatek,vpu: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Describes point to vpu. + + mediatek,scp: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Describes point to scp. + + power-domains: + maxItems: 1 + + "#address-cells": + const: 2 + + "#size-cells": + const: 2 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - iommus + +allOf: + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8183-vcodec-enc + - mediatek,mt8188-vcodec-enc + - mediatek,mt8192-vcodec-enc + - mediatek,mt8195-vcodec-enc + + then: + required: + - mediatek,scp + + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8173-vcodec-enc-vp8 + - mediatek,mt8173-vcodec-enc + + then: + required: + - mediatek,vpu + + - if: + properties: + compatible: + enum: + - mediatek,mt8173-vcodec-enc-vp8 + + then: + properties: + clock: + items: + minItems: 1 + maxItems: 1 + clock-names: + items: + - const: venc_lt_sel + else: + properties: + clock: + items: + minItems: 1 + maxItems: 1 + clock-names: + items: + - const: venc_sel + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/mt8173-clk.h> + #include <dt-bindings/memory/mt8173-larb-port.h> + #include <dt-bindings/interrupt-controller/irq.h> + + vcodec_enc_avc: vcodec@18002000 { + compatible = "mediatek,mt8173-vcodec-enc"; + reg = <0x18002000 0x1000>; + interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>; + iommus = <&iommu M4U_PORT_VENC_RCPU>, + <&iommu M4U_PORT_VENC_REC>, + <&iommu M4U_PORT_VENC_BSDMA>, + <&iommu M4U_PORT_VENC_SV_COMV>, + <&iommu M4U_PORT_VENC_RD_COMV>, + <&iommu M4U_PORT_VENC_CUR_LUMA>, + <&iommu M4U_PORT_VENC_CUR_CHROMA>, + <&iommu M4U_PORT_VENC_REF_LUMA>, + <&iommu M4U_PORT_VENC_REF_CHROMA>, + <&iommu M4U_PORT_VENC_NBM_RDMA>, + <&iommu M4U_PORT_VENC_NBM_WDMA>; + mediatek,vpu = <&vpu>; + clocks = <&topckgen CLK_TOP_VENC_SEL>; + clock-names = "venc_sel"; + assigned-clocks = <&topckgen CLK_TOP_VENC_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_VCODECPLL>; + }; + + vcodec_enc_vp8: vcodec@19002000 { + compatible = "mediatek,mt8173-vcodec-enc-vp8"; + reg = <0x19002000 0x1000>; /* VENC_LT_SYS */ + interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_LOW>; + iommus = <&iommu M4U_PORT_VENC_RCPU_SET2>, + <&iommu M4U_PORT_VENC_REC_FRM_SET2>, + <&iommu M4U_PORT_VENC_BSDMA_SET2>, + <&iommu M4U_PORT_VENC_SV_COMA_SET2>, + <&iommu M4U_PORT_VENC_RD_COMA_SET2>, + <&iommu M4U_PORT_VENC_CUR_LUMA_SET2>, + <&iommu M4U_PORT_VENC_CUR_CHROMA_SET2>, + <&iommu M4U_PORT_VENC_REF_LUMA_SET2>, + <&iommu M4U_PORT_VENC_REC_CHROMA_SET2>; + mediatek,vpu = <&vpu>; + clocks = <&topckgen CLK_TOP_VENC_LT_SEL>; + clock-names = "venc_lt_sel"; + assigned-clocks = <&topckgen CLK_TOP_VENC_LT_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_VCODECPLL_370P5>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek,vcodec-subdev-decoder.yaml b/Documentation/devicetree/bindings/media/mediatek,vcodec-subdev-decoder.yaml new file mode 100644 index 000000000..d1d209cbb --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek,vcodec-subdev-decoder.yaml @@ -0,0 +1,285 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek,vcodec-subdev-decoder.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek Video Decode Accelerator With Multi Hardware + +maintainers: + - Yunfei Dong <yunfei.dong@mediatek.com> + +description: | + MediaTek Video Decode Accelerator is the video decoding hardware present in + MediaTek SoCs that supports high-resolution decoding functionalities. + It consists of parent and child nodes. + + The decoder hardware block diagram is shown below: + + +------------------------------------------------+------------------------------+ + | | | + | input -> LAT-SoC HW -> LAT HW -> LAT buffer --|--> Core HW -> output buffer | + | || || | || | + +--------------||-----------||-------------------+-------||---------------------+ + LAT Workqueue | Core Workqueue <parent> + ---------------||-----------||-------------------|-------||---------------------- + ||<----------||---------HW index--------->|| <child> + \/ \/ \/ + +-------------------------------------------------------------+ + | enable/disable | + | clk power irq iommu | + | (lat/lat-soc/core0/core1) | + +-------------------------------------------------------------+ + + The child nodes represent the individual hardware blocks within the decoding + pipeline, such as LAT-SoC, LAT and Core. + Each child node is responsible for managing the dedicated resources of the + hardware, such as clocks, power domains, interrupts and IOMMUs. + + The parent node is a central point of control for the child nodes. + It identifies the specific video decoding pipeline architecture used by the + SoC, manages the shared resources like workqueues and platform data, and + handles V4L2 API calls on behalf of the underlying hardware. + + The parent utilizes two workqueues to manage the decoding process. + 1. LAT Workqueue, for LAT-SoC and LAT decoder: + Its workers take input bitstream and LAT buffer, enable the hardware for + decoding tasks, write the result to LAT buffer, and disable the hardware + after the LAT decoding is done. + 2. Core Workqueue, for Core decoder: + Its workers take LAT buffer and output buffer, enable the hardware for + decoding tasks, write the result to output buffer, and disable the hardware + after the Core decoding is done. + + These hardware decode each frame cyclically. + + The hardware might be associated with different SMI-common devices. + To prevent IOMMU faults during DRAM access in such cases, each hardware with + the unique SMI-common device must be placed under a separate parent node in + the device tree. + + LAT-SoC refers to another hardware block that connected to additional LARB + (local arbiter) ports, such as RDMA and UFO. + It requires independent power and clock control to work with LAT decoder, and + it doesn't have a dedicated interrupt. + + The used video decoding pipeline architecture across various Mediatek SoC: + MT8195: LAT-SoC + LAT + Core + MT8192: LAT + Core + MT8188: LAT + Core + MT8186: Core + +properties: + compatible: + enum: + - mediatek,mt8192-vcodec-dec + - mediatek,mt8186-vcodec-dec + - mediatek,mt8188-vcodec-dec + - mediatek,mt8195-vcodec-dec + + reg: + minItems: 1 + items: + - description: VDEC_SYS register space + - description: VDEC_RACING_CTRL register space + + iommus: + minItems: 1 + maxItems: 32 + description: | + List of the hardware port in respective IOMMU block for current Socs. + Refer to bindings/iommu/mediatek,iommu.yaml. + + mediatek,scp: + $ref: /schemas/types.yaml#/definitions/phandle + description: | + The node of system control processor (SCP), using + the remoteproc & rpmsg framework. + + "#address-cells": + const: 2 + + "#size-cells": + const: 2 + + ranges: true + +# Required child node: +patternProperties: + '^video-codec@[0-9a-f]+$': + type: object + + properties: + compatible: + enum: + - mediatek,mtk-vcodec-core + - mediatek,mtk-vcodec-lat + - mediatek,mtk-vcodec-lat-soc + + reg: + maxItems: 1 + description: VDEC_MISC register space + + interrupts: + maxItems: 1 + + iommus: + minItems: 1 + maxItems: 32 + description: | + List of the hardware port in respective IOMMU block for current Socs. + Refer to bindings/iommu/mediatek,iommu.yaml. + + clocks: + minItems: 4 + maxItems: 5 + + clock-names: + minItems: 4 + maxItems: 5 + + assigned-clocks: + maxItems: 1 + + assigned-clock-parents: + maxItems: 1 + + power-domains: + maxItems: 1 + + required: + - compatible + - reg + - iommus + - clocks + - clock-names + - assigned-clocks + - assigned-clock-parents + - power-domains + + additionalProperties: false + +required: + - compatible + - reg + - iommus + - mediatek,scp + - ranges + +if: + properties: + compatible: + contains: + enum: + - mediatek,mtk-vcodec-core + - mediatek,mtk-vcodec-lat + +then: + required: + - interrupts + +allOf: + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8192-vcodec-dec + then: + properties: + clock-names: + items: + - const: sel + - const: soc-vdec + - const: soc-lat + - const: vdec + - const: top + + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8195-vcodec-dec + then: + properties: + clock-names: + items: + - const: sel + - const: vdec + - const: lat + - const: top + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/memory/mt8192-larb-port.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/mt8192-clk.h> + #include <dt-bindings/power/mt8192-power.h> + + bus@16000000 { + #address-cells = <2>; + #size-cells = <2>; + ranges = <0 0x16000000 0x16000000 0 0x40000>; + + video-codec@16000000 { + compatible = "mediatek,mt8192-vcodec-dec"; + mediatek,scp = <&scp>; + iommus = <&iommu0 M4U_PORT_L4_VDEC_MC_EXT>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0 0 0 0x16000000 0 0x40000>; + reg = <0 0x16000000 0 0x1000>; /* VDEC_SYS */ + video-codec@10000 { + compatible = "mediatek,mtk-vcodec-lat"; + reg = <0 0x10000 0 0x800>; + interrupts = <GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH 0>; + iommus = <&iommu0 M4U_PORT_L5_VDEC_LAT0_VLD_EXT>, + <&iommu0 M4U_PORT_L5_VDEC_LAT0_VLD2_EXT>, + <&iommu0 M4U_PORT_L5_VDEC_LAT0_AVC_MV_EXT>, + <&iommu0 M4U_PORT_L5_VDEC_LAT0_PRED_RD_EXT>, + <&iommu0 M4U_PORT_L5_VDEC_LAT0_TILE_EXT>, + <&iommu0 M4U_PORT_L5_VDEC_LAT0_WDMA_EXT>, + <&iommu0 M4U_PORT_L5_VDEC_LAT0_RG_CTRL_DMA_EXT>, + <&iommu0 M4U_PORT_L5_VDEC_UFO_ENC_EXT>; + clocks = <&topckgen CLK_TOP_VDEC_SEL>, + <&vdecsys_soc CLK_VDEC_SOC_VDEC>, + <&vdecsys_soc CLK_VDEC_SOC_LAT>, + <&vdecsys_soc CLK_VDEC_SOC_LARB1>, + <&topckgen CLK_TOP_MAINPLL_D4>; + clock-names = "sel", "soc-vdec", "soc-lat", "vdec", "top"; + assigned-clocks = <&topckgen CLK_TOP_VDEC_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_MAINPLL_D4>; + power-domains = <&spm MT8192_POWER_DOMAIN_VDEC>; + }; + + video-codec@25000 { + compatible = "mediatek,mtk-vcodec-core"; + reg = <0 0x25000 0 0x1000>; + interrupts = <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH 0>; + iommus = <&iommu0 M4U_PORT_L4_VDEC_MC_EXT>, + <&iommu0 M4U_PORT_L4_VDEC_UFO_EXT>, + <&iommu0 M4U_PORT_L4_VDEC_PP_EXT>, + <&iommu0 M4U_PORT_L4_VDEC_PRED_RD_EXT>, + <&iommu0 M4U_PORT_L4_VDEC_PRED_WR_EXT>, + <&iommu0 M4U_PORT_L4_VDEC_PPWRAP_EXT>, + <&iommu0 M4U_PORT_L4_VDEC_TILE_EXT>, + <&iommu0 M4U_PORT_L4_VDEC_VLD_EXT>, + <&iommu0 M4U_PORT_L4_VDEC_VLD2_EXT>, + <&iommu0 M4U_PORT_L4_VDEC_AVC_MV_EXT>, + <&iommu0 M4U_PORT_L4_VDEC_RG_CTRL_DMA_EXT>; + clocks = <&topckgen CLK_TOP_VDEC_SEL>, + <&vdecsys CLK_VDEC_VDEC>, + <&vdecsys CLK_VDEC_LAT>, + <&vdecsys CLK_VDEC_LARB1>, + <&topckgen CLK_TOP_MAINPLL_D4>; + clock-names = "sel", "soc-vdec", "soc-lat", "vdec", "top"; + assigned-clocks = <&topckgen CLK_TOP_VDEC_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_MAINPLL_D4>; + power-domains = <&spm MT8192_POWER_DOMAIN_VDEC2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.yaml b/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.yaml new file mode 100644 index 000000000..a4aacd3eb --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.yaml @@ -0,0 +1,82 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek-jpeg-decoder.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek JPEG Decoder + +maintainers: + - Xia Jiang <xia.jiang@mediatek.com> + +description: |- + Mediatek JPEG Decoder is the JPEG decode hardware present in Mediatek SoCs + +properties: + compatible: + oneOf: + - items: + - enum: + - mediatek,mt8173-jpgdec + - mediatek,mt2701-jpgdec + - items: + - enum: + - mediatek,mt7623-jpgdec + - mediatek,mt8188-jpgdec + - const: mediatek,mt2701-jpgdec + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 2 + minItems: 2 + + clock-names: + items: + - const: jpgdec-smi + - const: jpgdec + + power-domains: + maxItems: 1 + + iommus: + minItems: 2 + maxItems: 32 + description: | + Points to the respective IOMMU block with master port as argument, see + Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml for details. + Ports are according to the HW. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + - iommus + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt2701-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/memory/mt2701-larb-port.h> + #include <dt-bindings/power/mt2701-power.h> + jpegdec: jpegdec@15004000 { + compatible = "mediatek,mt2701-jpgdec"; + reg = <0x15004000 0x1000>; + interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_LOW>; + clocks = <&imgsys CLK_IMG_JPGDEC_SMI>, + <&imgsys CLK_IMG_JPGDEC>; + clock-names = "jpgdec-smi", + "jpgdec"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>; + iommus = <&iommu MT2701_M4U_PORT_JPGDEC_WDMA>, + <&iommu MT2701_M4U_PORT_JPGDEC_BSDMA>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-jpeg-encoder.yaml b/Documentation/devicetree/bindings/media/mediatek-jpeg-encoder.yaml new file mode 100644 index 000000000..5b15f8977 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-jpeg-encoder.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/mediatek-jpeg-encoder.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek JPEG Encoder + +maintainers: + - Xia Jiang <xia.jiang@mediatek.com> + +description: |- + MediaTek JPEG Encoder is the JPEG encode hardware present in MediaTek SoCs + +properties: + compatible: + items: + - enum: + - mediatek,mt2701-jpgenc + - mediatek,mt8183-jpgenc + - mediatek,mt8186-jpgenc + - mediatek,mt8188-jpgenc + - const: mediatek,mtk-jpgenc + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: jpgenc + + power-domains: + maxItems: 1 + + iommus: + minItems: 2 + maxItems: 32 + description: | + Points to the respective IOMMU block with master port as argument, see + Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml for details. + Ports are according to the HW. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + - iommus + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt2701-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/memory/mt2701-larb-port.h> + #include <dt-bindings/power/mt2701-power.h> + jpegenc: jpegenc@1500a000 { + compatible = "mediatek,mt2701-jpgenc", + "mediatek,mtk-jpgenc"; + reg = <0x1500a000 0x1000>; + interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_LOW>; + clocks = <&imgsys CLK_IMG_VENC>; + clock-names = "jpgenc"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>; + iommus = <&iommu MT2701_M4U_PORT_JPGENC_RDMA>, + <&iommu MT2701_M4U_PORT_JPGENC_BSDMA>; + }; diff --git a/Documentation/devicetree/bindings/media/microchip,csi2dc.yaml b/Documentation/devicetree/bindings/media/microchip,csi2dc.yaml new file mode 100644 index 000000000..b3a345fc6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/microchip,csi2dc.yaml @@ -0,0 +1,199 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/microchip,csi2dc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip CSI2 Demux Controller (CSI2DC) + +maintainers: + - Eugen Hristev <eugen.hristev@microchip.com> + +description: + CSI2DC - Camera Serial Interface 2 Demux Controller + + CSI2DC is a hardware block that receives incoming data from either from an + IDI interface or from a parallel bus interface. + It filters IDI packets based on their data type and virtual channel + identifier, then converts the byte stream to a pixel stream into a cross + clock domain towards a parallel interface that can be read by a sensor + controller. + IDI interface is Synopsys proprietary. + CSI2DC can act a simple bypass bridge if the incoming data is coming from + a parallel interface. + + CSI2DC provides two pipes, one video pipe and one data pipe. Video pipe + is connected at the output to a sensor controller and the data pipe is + accessible as a DMA slave port to a DMA controller. + + CSI2DC supports a single 'port' node as a sink port with either Synopsys + 32-bit IDI interface or a parallel interface. + + CSI2DC supports one 'port' node as source port with parallel interface. + This is called video pipe. + This port has an 'endpoint' that can be connected to a sink port of another + controller (next in pipeline). + + CSI2DC also supports direct access to the data through AHB, via DMA channel, + called data pipe. + For data pipe to be available, a dma controller and a dma channel must be + referenced. + +properties: + compatible: + const: microchip,sama7g5-csi2dc + + reg: + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 2 + + clock-names: + description: + CSI2DC must have two clocks to function correctly. One clock is the + peripheral clock for the inside functionality of the hardware block. + This is named 'pclk'. The second clock must be the cross domain clock, + in which CSI2DC will perform clock crossing. This clock must be fed + by the next controller in pipeline, which usually is a sensor controller. + Normally this clock should be given by this sensor controller who + is also a clock source. This clock is named 'scck', sensor controller clock. + items: + - const: pclk + - const: scck + + dmas: + maxItems: 1 + + dma-names: + const: rx + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port node, single endpoint describing the input port. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + description: Endpoint connected to input device + + properties: + bus-type: + enum: [4, 5, 6] + default: 4 + + bus-width: + enum: [8, 9, 10, 11, 12, 13, 14] + default: 14 + + clock-noncontinuous: + type: boolean + description: + Presence of this boolean property decides whether clock is + continuous or noncontinuous. + + remote-endpoint: true + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Output port node, single endpoint describing the output port. + + properties: + endpoint: + unevaluatedProperties: false + $ref: video-interfaces.yaml# + description: Endpoint connected to output device + + properties: + bus-type: + enum: [5, 6] + default: 5 + + bus-width: + enum: [8, 9, 10, 11, 12, 13, 14] + default: 14 + + remote-endpoint: true + + required: + - port@0 + - port@1 + +additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - ports + +examples: + # Example for connecting to a parallel sensor controller block (video pipe) + # and the input is received from Synopsys IDI interface + - | + csi2dc@e1404000 { + compatible = "microchip,sama7g5-csi2dc"; + reg = <0xe1404000 0x500>; + clocks = <&pclk>, <&scck>; + clock-names = "pclk", "scck"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; /* must be 0, first child port */ + csi2dc_in: endpoint { /* input from IDI interface */ + bus-type = <4>; /* MIPI CSI2 D-PHY */ + remote-endpoint = <&csi2host_out>; + }; + }; + + port@1 { + reg = <1>; /* must be 1, second child port */ + csi2dc_out: endpoint { + remote-endpoint = <&xisc_in>; /* output to sensor controller */ + }; + }; + }; + }; + + # Example for connecting to a DMA master as an AHB slave + # and the input is received from Synopsys IDI interface + - | + #include <dt-bindings/dma/at91.h> + csi2dc@e1404000 { + compatible = "microchip,sama7g5-csi2dc"; + reg = <0xe1404000 0x500>; + clocks = <&pclk>, <&scck>; + clock-names = "pclk", "scck"; + dmas = <&dma0 AT91_XDMAC_DT_PERID(34)>; + dma-names = "rx"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; /* must be 0, first child port */ + csi2dc_input: endpoint { /* input from IDI interface */ + remote-endpoint = <&csi2host_out>; + }; + }; + + port@1 { + reg = <1>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/microchip,sama5d4-vdec.yaml b/Documentation/devicetree/bindings/media/microchip,sama5d4-vdec.yaml new file mode 100644 index 000000000..ede086d55 --- /dev/null +++ b/Documentation/devicetree/bindings/media/microchip,sama5d4-vdec.yaml @@ -0,0 +1,46 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/microchip,sama5d4-vdec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Hantro G1 VPU codec implemented on Microchip SAMA5D4 SoCs + +maintainers: + - Emil Velikov <emil.velikov@collabora.com> + +description: + Hantro G1 video decode accelerator present on Microchip SAMA5D4 SoCs. + +properties: + compatible: + const: microchip,sama5d4-vdec + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/at91.h> + #include <dt-bindings/interrupt-controller/irq.h> + + vdec@300000 { + compatible = "microchip,sama5d4-vdec"; + reg = <0x00300000 0x100000>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 4>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>; + }; diff --git a/Documentation/devicetree/bindings/media/microchip,xisc.yaml b/Documentation/devicetree/bindings/media/microchip,xisc.yaml new file mode 100644 index 000000000..25f5f79d4 --- /dev/null +++ b/Documentation/devicetree/bindings/media/microchip,xisc.yaml @@ -0,0 +1,129 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2021 Microchip Technology, Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/microchip,xisc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip eXtended Image Sensor Controller (XISC) + +maintainers: + - Eugen Hristev <eugen.hristev@microchip.com> + +description: | + The eXtended Image Sensor Controller (XISC) device provides the video input capabilities for the + Microchip AT91 SAM family of devices. + + The XISC has a single internal parallel input that supports RAW Bayer, RGB or YUV video. + The source can be either a demuxer from a CSI2 type of bus, or a simple direct bridge to a + parallel sensor. + + The XISC provides one clock output that is used to clock the demuxer/bridge. + +properties: + compatible: + const: microchip,sama7g5-isc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: hclock + + '#clock-cells': + const: 0 + + clock-output-names: + const: isc-mck + + microchip,mipi-mode: + type: boolean + description: + As the XISC is usually connected to a demux/bridge, the XISC receives + the same type of input, however, it should be aware of the type of + signals received. The mipi-mode enables different internal handling + of the data and clock lines. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + description: + Input port node, single endpoint describing the input pad. + + properties: + endpoint: + $ref: video-interfaces.yaml# + + properties: + bus-type: + enum: [5, 6] + + remote-endpoint: true + + bus-width: + enum: [8, 9, 10, 11, 12, 14] + default: 12 + + hsync-active: + enum: [0, 1] + default: 1 + + vsync-active: + enum: [0, 1] + default: 1 + + pclk-sample: + enum: [0, 1] + default: 1 + + required: + - remote-endpoint + - bus-type + + additionalProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - '#clock-cells' + - clock-output-names + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/at91.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/media/video-interfaces.h> + + xisc: xisc@e1408000 { + compatible = "microchip,sama7g5-isc"; + reg = <0xe1408000 0x2000>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 56>; + clock-names = "hclock"; + #clock-cells = <0>; + clock-output-names = "isc-mck"; + + port { + xisc_in: endpoint { + bus-type = <MEDIA_BUS_TYPE_PARALLEL>; + remote-endpoint = <&csi2dc_out>; + hsync-active = <1>; + vsync-active = <1>; + bus-width = <12>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/nuvoton,npcm-ece.yaml b/Documentation/devicetree/bindings/media/nuvoton,npcm-ece.yaml new file mode 100644 index 000000000..b47468e54 --- /dev/null +++ b/Documentation/devicetree/bindings/media/nuvoton,npcm-ece.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/nuvoton,npcm-ece.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Nuvoton NPCM Encoding Compression Engine + +maintainers: + - Joseph Liu <kwliu@nuvoton.com> + - Marvin Lin <kflin@nuvoton.com> + +description: | + Video Encoding Compression Engine (ECE) present on Nuvoton NPCM SoCs. + +properties: + compatible: + enum: + - nuvoton,npcm750-ece + - nuvoton,npcm845-ece + + reg: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/reset/nuvoton,npcm7xx-reset.h> + + ece: video-codec@f0820000 { + compatible = "nuvoton,npcm750-ece"; + reg = <0xf0820000 0x2000>; + resets = <&rstc NPCM7XX_RESET_IPSRST2 NPCM7XX_RESET_ECE>; + }; diff --git a/Documentation/devicetree/bindings/media/nuvoton,npcm-vcd.yaml b/Documentation/devicetree/bindings/media/nuvoton,npcm-vcd.yaml new file mode 100644 index 000000000..c885f559d --- /dev/null +++ b/Documentation/devicetree/bindings/media/nuvoton,npcm-vcd.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/nuvoton,npcm-vcd.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Nuvoton NPCM Video Capture/Differentiation Engine + +maintainers: + - Joseph Liu <kwliu@nuvoton.com> + - Marvin Lin <kflin@nuvoton.com> + +description: | + Video Capture/Differentiation Engine (VCD) present on Nuvoton NPCM SoCs. + +properties: + compatible: + enum: + - nuvoton,npcm750-vcd + - nuvoton,npcm845-vcd + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + resets: + maxItems: 1 + + nuvoton,sysgcr: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to access GCR (Global Control Register) registers. + + nuvoton,sysgfxi: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to access GFXI (Graphics Core Information) registers. + + nuvoton,ece: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to access ECE (Encoding Compression Engine) registers. + + memory-region: + maxItems: 1 + description: + CMA pool to use for buffers allocation instead of the default CMA pool. + +required: + - compatible + - reg + - interrupts + - resets + - nuvoton,sysgcr + - nuvoton,sysgfxi + - nuvoton,ece + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/reset/nuvoton,npcm7xx-reset.h> + + vcd: vcd@f0810000 { + compatible = "nuvoton,npcm750-vcd"; + reg = <0xf0810000 0x10000>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + resets = <&rstc NPCM7XX_RESET_IPSRST2 NPCM7XX_RESET_VCD>; + nuvoton,sysgcr = <&gcr>; + nuvoton,sysgfxi = <&gfxi>; + nuvoton,ece = <&ece>; + }; diff --git a/Documentation/devicetree/bindings/media/nvidia,tegra-vde.yaml b/Documentation/devicetree/bindings/media/nvidia,tegra-vde.yaml new file mode 100644 index 000000000..4ecdee1be --- /dev/null +++ b/Documentation/devicetree/bindings/media/nvidia,tegra-vde.yaml @@ -0,0 +1,119 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/nvidia,tegra-vde.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra Video Decoder Engine + +maintainers: + - Dmitry Osipenko <digetx@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + - Thierry Reding <thierry.reding@gmail.com> + +properties: + compatible: + oneOf: + - items: + - enum: + - nvidia,tegra132-vde + - nvidia,tegra124-vde + - nvidia,tegra114-vde + - items: + - const: nvidia,tegra30-vde + - const: nvidia,tegra20-vde + - items: + - const: nvidia,tegra20-vde + + reg: + maxItems: 9 + + reg-names: + items: + - const: sxe + - const: bsev + - const: mbe + - const: ppe + - const: mce + - const: tfe + - const: ppb + - const: vdma + - const: frameid + + clocks: + maxItems: 1 + + resets: + maxItems: 2 + + reset-names: + items: + - const: vde + - const: mc + + interrupts: + maxItems: 3 + + interrupt-names: + items: + - const: sync-token + - const: bsev + - const: sxe + + iommus: + maxItems: 1 + + iram: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle of the SRAM MMIO node. + + operating-points-v2: + description: + Should contain freqs and voltages and opp-supported-hw property, + which is a bitfield indicating SoC speedo or process ID mask. + + power-domains: + maxItems: 1 + description: + Phandle to the SoC core power domain. + +required: + - compatible + - reg + - reg-names + - clocks + - resets + - reset-names + - interrupts + - interrupt-names + +additionalProperties: false + +examples: + - | + video-codec@6001a000 { + compatible = "nvidia,tegra20-vde"; + reg = <0x6001a000 0x1000>, /* Syntax Engine */ + <0x6001b000 0x1000>, /* Video Bitstream Engine */ + <0x6001c000 0x100>, /* Macroblock Engine */ + <0x6001c200 0x100>, /* Post-processing Engine */ + <0x6001c400 0x100>, /* Motion Compensation Engine */ + <0x6001c600 0x100>, /* Transform Engine */ + <0x6001c800 0x100>, /* Pixel prediction block */ + <0x6001ca00 0x100>, /* Video DMA */ + <0x6001d800 0x300>; /* Video frame controls */ + reg-names = "sxe", "bsev", "mbe", "ppe", "mce", + "tfe", "ppb", "vdma", "frameid"; + iram = <&iram>; /* IRAM MMIO region */ + interrupts = <0 9 4>, /* Sync token */ + <0 10 4>, /* BSE-V */ + <0 12 4>; /* SXE */ + interrupt-names = "sync-token", "bsev", "sxe"; + clocks = <&clk 61>; + reset-names = "vde", "mc"; + resets = <&rst 61>, <&mem 13>; + iommus = <&mem 15>; + operating-points-v2 = <&dvfs_opp_table>; + power-domains = <&domain>; + }; diff --git a/Documentation/devicetree/bindings/media/nxp,dw100.yaml b/Documentation/devicetree/bindings/media/nxp,dw100.yaml new file mode 100644 index 000000000..21910ff0e --- /dev/null +++ b/Documentation/devicetree/bindings/media/nxp,dw100.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/nxp,dw100.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP i.MX8MP DW100 Dewarper core + +maintainers: + - Xavier Roumegue <xavier.roumegue@oss.nxp.com> + +description: |- + The Dewarp Engine provides high-performance dewarp processing for the + correction of the distortion that is introduced in images produced by fisheye + and wide angle lenses. It is implemented with a line/tile-cache based + architecture. With configurable address mapping look up tables and per tile + processing, it successfully generates a corrected output image. + The engine can be used to perform scaling, cropping and pixel format + conversion. + +properties: + compatible: + enum: + - nxp,imx8mp-dw100 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: The AXI clock + - description: The AHB clock + + clock-names: + items: + - const: axi + - const: ahb + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx8mp-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/imx8mp-power.h> + + dewarp: dwe@32e30000 { + compatible = "nxp,imx8mp-dw100"; + reg = <0x32e30000 0x10000>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>, + <&clk IMX8MP_CLK_MEDIA_APB_ROOT>; + clock-names = "axi", "ahb"; + power-domains = <&media_blk_ctrl IMX8MP_MEDIABLK_PD_DWE>; + }; diff --git a/Documentation/devicetree/bindings/media/nxp,imx-mipi-csi2.yaml b/Documentation/devicetree/bindings/media/nxp,imx-mipi-csi2.yaml new file mode 100644 index 000000000..41ad5b84e --- /dev/null +++ b/Documentation/devicetree/bindings/media/nxp,imx-mipi-csi2.yaml @@ -0,0 +1,233 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/nxp,imx-mipi-csi2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP i.MX7 and i.MX8 MIPI CSI-2 receiver + +maintainers: + - Rui Miguel Silva <rmfrfs@gmail.com> + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: |- + The NXP i.MX7 and i.MX8 families contain SoCs that include a MIPI CSI-2 + receiver IP core named CSIS. The IP core originates from Samsung, and may be + compatible with some of the Exynos4 and S5P SoCs. i.MX7 SoCs use CSIS version + 3.3, and i.MX8 SoCs use CSIS version 3.6.3. + + While the CSI-2 receiver is separate from the MIPI D-PHY IP core, the PHY is + completely wrapped by the CSIS and doesn't expose a control interface of its + own. This binding thus covers both IP cores. + +properties: + compatible: + oneOf: + - enum: + - fsl,imx7-mipi-csi2 + - fsl,imx8mm-mipi-csi2 + - items: + - enum: + - fsl,imx8mp-mipi-csi2 + - const: fsl,imx8mm-mipi-csi2 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 3 + items: + - description: The peripheral clock (a.k.a. APB clock) + - description: The external clock (optionally used as the pixel clock) + - description: The MIPI D-PHY clock + - description: The AXI clock + + clock-names: + minItems: 3 + items: + - const: pclk + - const: wrap + - const: phy + - const: axi + + power-domains: + maxItems: 1 + + phy-supply: + description: The MIPI D-PHY digital power supply + + resets: + items: + - description: MIPI D-PHY slave reset + + clock-frequency: + description: The desired external clock ("wrap") frequency, in Hz + default: 166000000 + deprecated: true + + fsl,num-channels: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Number of output channels + minimum: 1 + maximum: 4 + default: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: + Note that 'fsl,imx7-mipi-csi2' only supports up to 2 data lines. + minItems: 1 + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Output port node + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + - ports + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + const: fsl,imx7-mipi-csi2 + then: + required: + - phy-supply + - resets + else: + properties: + clocks: + minItems: 4 + clock-names: + minItems: 4 + phy-supply: false + resets: false + +examples: + - | + #include <dt-bindings/clock/imx7d-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/reset/imx7-reset.h> + + mipi-csi@30750000 { + compatible = "fsl,imx7-mipi-csi2"; + reg = <0x30750000 0x10000>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&clks IMX7D_IPG_ROOT_CLK>, + <&clks IMX7D_MIPI_CSI_ROOT_CLK>, + <&clks IMX7D_MIPI_DPHY_ROOT_CLK>; + clock-names = "pclk", "wrap", "phy"; + + assigned-clocks = <&clks IMX7D_MIPI_CSI_ROOT_CLK>; + assigned-clock-rates = <166000000>; + + power-domains = <&pgc_mipi_phy>; + phy-supply = <®_1p0d>; + resets = <&src IMX7_RESET_MIPI_PHY_MRST>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + mipi_from_sensor: endpoint { + remote-endpoint = <&ov2680_to_mipi>; + data-lanes = <1>; + }; + }; + + port@1 { + reg = <1>; + + mipi_vc0_to_csi_mux: endpoint { + remote-endpoint = <&csi_mux_from_mipi_vc0>; + }; + }; + }; + }; + + - | + #include <dt-bindings/clock/imx8mm-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mipi-csi@32e30000 { + compatible = "fsl,imx8mm-mipi-csi2"; + reg = <0x32e30000 0x1000>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&clk IMX8MM_CLK_DISP_APB_ROOT>, + <&clk IMX8MM_CLK_CSI1_ROOT>, + <&clk IMX8MM_CLK_CSI1_PHY_REF>, + <&clk IMX8MM_CLK_DISP_AXI_ROOT>; + clock-names = "pclk", "wrap", "phy", "axi"; + + assigned-clocks = <&clk IMX8MM_CLK_CSI1_ROOT>; + assigned-clock-rates = <250000000>; + + power-domains = <&mipi_pd>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + imx8mm_mipi_csi_in: endpoint { + remote-endpoint = <&imx477_out>; + data-lanes = <1 2 3 4>; + }; + }; + + port@1 { + reg = <1>; + + imx8mm_mipi_csi_out: endpoint { + remote-endpoint = <&csi_in>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/nxp,imx7-csi.yaml b/Documentation/devicetree/bindings/media/nxp,imx7-csi.yaml new file mode 100644 index 000000000..326284e15 --- /dev/null +++ b/Documentation/devicetree/bindings/media/nxp,imx7-csi.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/nxp,imx7-csi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: i.MX7 and i.MX8 CSI bridge (CMOS Sensor Interface) + +maintainers: + - Rui Miguel Silva <rmfrfs@gmail.com> + +description: | + This is device node for the CMOS Sensor Interface (CSI) which enables the + chip to connect directly to external CMOS image sensors. + +properties: + compatible: + oneOf: + - enum: + - fsl,imx8mq-csi + - fsl,imx7-csi + - fsl,imx6ul-csi + - items: + - const: fsl,imx8mm-csi + - const: fsl,imx7-csi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: mclk + + power-domains: + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/properties/port + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - port + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + enum: + - fsl,imx8mm-csi + then: + required: + - power-domains + +examples: + - | + #include <dt-bindings/clock/imx7d-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + csi: csi@30710000 { + compatible = "fsl,imx7-csi"; + reg = <0x30710000 0x10000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_CSI_MCLK_ROOT_CLK>; + clock-names = "mclk"; + + port { + csi_from_csi_mux: endpoint { + remote-endpoint = <&csi_mux_to_csi>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/nxp,imx8-isi.yaml b/Documentation/devicetree/bindings/media/nxp,imx8-isi.yaml new file mode 100644 index 000000000..b59c4ce30 --- /dev/null +++ b/Documentation/devicetree/bindings/media/nxp,imx8-isi.yaml @@ -0,0 +1,215 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/nxp,imx8-isi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: i.MX8 Image Sensing Interface + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: | + The Image Sensing Interface (ISI) combines image processing pipelines with + DMA engines to process and capture frames originating from a variety of + sources. The inputs to the ISI go through Pixel Link interfaces, and their + number and nature is SoC-dependent. They cover both capture interfaces (MIPI + CSI-2 RX, HDMI RX, ...) and display engine outputs for writeback support. + +properties: + compatible: + enum: + - fsl,imx8mn-isi + - fsl,imx8mp-isi + - fsl,imx8ulp-isi + - fsl,imx91-isi + - fsl,imx93-isi + - fsl,imx95-isi + + reg: + maxItems: 1 + + clocks: + items: + - description: The AXI clock + - description: The APB clock + # TODO: Check if the per-channel ipg_proc_clk clocks need to be specified + # as well, in case some SoCs have the ability to control them separately. + # This may be the case of the i.MX8[DQ]X(P) + + clock-names: + items: + - const: axi + - const: apb + + fsl,blk-ctrl: + $ref: /schemas/types.yaml#/definitions/phandle + description: + A phandle referencing the block control that contains the CSIS to ISI + gasket. + + interrupts: + description: Processing pipeline interrupts, one per pipeline + minItems: 1 + maxItems: 8 + + power-domains: + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: | + Ports represent the Pixel Link inputs to the ISI. Their number and + assignment are model-dependent. Each port shall have a single endpoint. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - ports + +allOf: + - if: + properties: + compatible: + contains: + enum: + - fsl,imx8mn-isi + - fsl,imx8ulp-isi + - fsl,imx91-isi + - fsl,imx93-isi + then: + properties: + interrupts: + maxItems: 1 + ports: + properties: + port@0: + description: MIPI CSI-2 RX + port@1: false + required: + - port@0 + + - if: + properties: + compatible: + contains: + const: fsl,imx8mp-isi + then: + properties: + interrupts: + minItems: 2 + maxItems: 2 + ports: + properties: + port@0: + description: MIPI CSI-2 RX 0 + port@1: + description: MIPI CSI-2 RX 1 + required: + - port@0 + - port@1 + + - if: + properties: + compatible: + not: + contains: + const: fsl,imx91-isi + then: + required: + - fsl,blk-ctrl + + - if: + properties: + compatible: + contains: + const: fsl,imx95-isi + then: + properties: + interrupts: + minItems: 8 + ports: + properties: + port@0: + description: Pixel Link Slave 0 + port@1: + description: Pixel Link Slave 1 + port@2: + description: MIPI CSI-2 RX 0 + port@3: + description: MIPI CSI-2 RX 1 + required: + - port@2 + - port@3 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx8mn-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/power/imx8mn-power.h> + + isi@32e20000 { + compatible = "fsl,imx8mn-isi"; + reg = <0x32e20000 0x100>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MN_CLK_DISP_AXI_ROOT>, + <&clk IMX8MN_CLK_DISP_APB_ROOT>; + clock-names = "axi", "apb"; + fsl,blk-ctrl = <&disp_blk_ctrl>; + power-domains = <&disp_blk_ctrl IMX8MN_DISPBLK_PD_ISI>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + isi_in: endpoint { + remote-endpoint = <&mipi_csi_out>; + }; + }; + }; + }; + + - | + #include <dt-bindings/clock/imx8mp-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + isi@32e00000 { + compatible = "fsl,imx8mp-isi"; + reg = <0x32e00000 0x4000>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>, + <&clk IMX8MP_CLK_MEDIA_APB_ROOT>; + clock-names = "axi", "apb"; + fsl,blk-ctrl = <&media_blk_ctrl>; + power-domains = <&mediamix_pd>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + isi_in_0: endpoint { + remote-endpoint = <&mipi_csi_0_out>; + }; + }; + + port@1 { + reg = <1>; + isi_in_1: endpoint { + remote-endpoint = <&mipi_csi_1_out>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/nxp,imx8-jpeg.yaml b/Documentation/devicetree/bindings/media/nxp,imx8-jpeg.yaml new file mode 100644 index 000000000..6ba668aa6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/nxp,imx8-jpeg.yaml @@ -0,0 +1,127 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/nxp,imx8-jpeg.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: i.MX8QXP/QM JPEG decoder/encoder + +maintainers: + - Mirela Rabulea <mirela.rabulea@nxp.com> + +description: |- + The JPEG decoder/encoder present in iMX8QXP and iMX8QM SoCs is an + ISO/IEC 10918-1 JPEG standard compliant decoder/encoder, for Baseline + and Extended Sequential DCT modes. + +properties: + compatible: + oneOf: + - items: + enum: + - nxp,imx8qxp-jpgdec + - nxp,imx8qxp-jpgenc + - items: + - enum: + - nxp,imx8qm-jpgdec + - nxp,imx95-jpgdec + - const: nxp,imx8qxp-jpgdec + - items: + - enum: + - nxp,imx8qm-jpgenc + - nxp,imx95-jpgenc + - const: nxp,imx8qxp-jpgenc + + reg: + maxItems: 1 + + clocks: + items: + - description: AXI DMA engine clock for fetching JPEG bitstream from memory (per) + - description: IP bus clock for register access (ipg) + + interrupts: + description: | + There are 4 slots available in the IP, which the driver may use + If a certain slot is used, it should have an associated interrupt + The interrupt with index i is assumed to be for slot i + minItems: 1 # At least one slot is needed by the driver + maxItems: 4 # The IP has 4 slots available for use + + power-domains: + description: + List of phandle and PM domain specifier as documented in + Documentation/devicetree/bindings/power/power_domain.txt + minItems: 1 # Wrapper and all slots + maxItems: 5 # Wrapper and 4 slots + + sram: + maxItems: 1 + description: + The SRAM can be used for descriptor storage, which may improve bus + utilization. + +required: + - compatible + - reg + - clocks + - interrupts + - power-domains + +allOf: + - if: + properties: + compatible: + contains: + enum: + - nxp,imx95-jpgenc + - nxp,imx95-jpgdec + then: + properties: + power-domains: + maxItems: 1 + else: + properties: + power-domains: + minItems: 2 # Wrapper and 1 slot + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx8-lpcg.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/firmware/imx/rsrc.h> + + jpegdec: jpegdec@58400000 { + compatible = "nxp,imx8qxp-jpgdec"; + reg = <0x58400000 0x00050000 >; + clocks = <&img_jpeg_dec_lpcg IMX_LPCG_CLK_0>, + <&img_jpeg_dec_lpcg IMX_LPCG_CLK_4>; + interrupts = <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&pd IMX_SC_R_MJPEG_DEC_MP>, + <&pd IMX_SC_R_MJPEG_DEC_S0>, + <&pd IMX_SC_R_MJPEG_DEC_S1>, + <&pd IMX_SC_R_MJPEG_DEC_S2>, + <&pd IMX_SC_R_MJPEG_DEC_S3>; + }; + + jpegenc: jpegenc@58450000 { + compatible = "nxp,imx8qm-jpgenc", "nxp,imx8qxp-jpgenc"; + reg = <0x58450000 0x00050000 >; + clocks = <&img_jpeg_enc_lpcg IMX_LPCG_CLK_0>, + <&img_jpeg__lpcg IMX_LPCG_CLK_4>; + interrupts = <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&pd IMX_SC_R_MJPEG_ENC_MP>, + <&pd IMX_SC_R_MJPEG_ENC_S0>, + <&pd IMX_SC_R_MJPEG_ENC_S1>, + <&pd IMX_SC_R_MJPEG_ENC_S2>, + <&pd IMX_SC_R_MJPEG_ENC_S3>; + }; +... diff --git a/Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml b/Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml new file mode 100644 index 000000000..4fcfc4fd3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml @@ -0,0 +1,239 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/nxp,imx8mq-mipi-csi2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP i.MX8MQ MIPI CSI-2 receiver + +maintainers: + - Martin Kepplinger <martin.kepplinger@puri.sm> + +description: |- + This binding covers the CSI-2 RX PHY and host controller included in the + NXP i.MX8MQ SoC. It handles the sensor/image input and process for all the + input imaging devices. + +properties: + compatible: + oneOf: + - enum: + - fsl,imx8mq-mipi-csi2 + - fsl,imx8qxp-mipi-csi2 + - fsl,imx8ulp-mipi-csi2 + - items: + - const: fsl,imx8qm-mipi-csi2 + - const: fsl,imx8qxp-mipi-csi2 + + reg: + items: + - description: MIPI CSI-2 RX host controller register. + - description: MIPI CSI-2 control and status register (csr). + minItems: 1 + + clocks: + items: + - description: core is the RX Controller Core Clock input. This clock + must be exactly equal to or faster than the receive + byteclock from the RX DPHY. + - description: esc is the Rx Escape Clock. This must be the same escape + clock that the RX DPHY receives. + - description: ui is the pixel clock (phy_ref up to 333Mhz). + See the reference manual for details. + - description: pclk is clock for csr APB interface. + minItems: 3 + + clock-names: + items: + - const: core + - const: esc + - const: ui + - const: pclk + minItems: 3 + + power-domains: + maxItems: 1 + + resets: + items: + - description: CORE_RESET reset register bit definition + - description: PHY_REF_RESET reset register bit definition + - description: ESC_RESET reset register bit definition + minItems: 1 + + fsl,mipi-phy-gpr: + description: | + The phandle to the imx8mq syscon iomux-gpr with the register + for setting RX_ENABLE for the mipi receiver. + + The format should be as follows: + <gpr req_gpr> + gpr is the phandle to general purpose register node. + req_gpr is the gpr register offset of RX_ENABLE for the mipi phy. + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: The 'gpr' is the phandle to general purpose register node. + - description: The 'req_gpr' is the gpr register offset containing + CSI2_1_RX_ENABLE or CSI2_2_RX_ENABLE respectively. + maximum: 0xff + + interconnects: + maxItems: 1 + + interconnect-names: + const: dram + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Output port node + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - clocks + - clock-names + - power-domains + - resets + - ports + +allOf: + - if: + properties: + compatible: + contains: + enum: + - fsl,imx8mq-mipi-csi2 + then: + properties: + reg: + maxItems: 1 + resets: + minItems: 3 + clocks: + maxItems: 3 + clock-names: + maxItems: 3 + required: + - fsl,mipi-phy-gpr + + - if: + properties: + compatible: + contains: + const: fsl,imx8qxp-mipi-csi2 + then: + properties: + reg: + minItems: 2 + resets: + maxItems: 1 + clocks: + maxItems: 3 + clock-names: + maxItems: 3 + + - if: + properties: + compatible: + contains: + enum: + - fsl,imx8ulp-mipi-csi2 + then: + properties: + reg: + minItems: 2 + resets: + minItems: 2 + maxItems: 2 + clocks: + minItems: 4 + clock-names: + minItems: 4 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx8mq-clock.h> + #include <dt-bindings/interconnect/imx8mq.h> + #include <dt-bindings/reset/imx8mq-reset.h> + + csi@30a70000 { + compatible = "fsl,imx8mq-mipi-csi2"; + reg = <0x30a70000 0x1000>; + clocks = <&clk IMX8MQ_CLK_CSI1_CORE>, + <&clk IMX8MQ_CLK_CSI1_ESC>, + <&clk IMX8MQ_CLK_CSI1_PHY_REF>; + clock-names = "core", "esc", "ui"; + assigned-clocks = <&clk IMX8MQ_CLK_CSI1_CORE>, + <&clk IMX8MQ_CLK_CSI1_PHY_REF>, + <&clk IMX8MQ_CLK_CSI1_ESC>; + assigned-clock-rates = <266000000>, <200000000>, <66000000>; + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>, + <&clk IMX8MQ_SYS2_PLL_1000M>, + <&clk IMX8MQ_SYS1_PLL_800M>; + power-domains = <&pgc_mipi_csi1>; + resets = <&src IMX8MQ_RESET_MIPI_CSI1_CORE_RESET>, + <&src IMX8MQ_RESET_MIPI_CSI1_PHY_REF_RESET>, + <&src IMX8MQ_RESET_MIPI_CSI1_ESC_RESET>; + fsl,mipi-phy-gpr = <&iomuxc_gpr 0x88>; + interconnects = <&noc IMX8MQ_ICM_CSI1 &noc IMX8MQ_ICS_DRAM>; + interconnect-names = "dram"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + imx8mm_mipi_csi_in: endpoint { + remote-endpoint = <&imx477_out>; + data-lanes = <1 2 3 4>; + }; + }; + + port@1 { + reg = <1>; + + imx8mm_mipi_csi_out: endpoint { + remote-endpoint = <&csi_in>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/nxp,imx8mq-vpu.yaml b/Documentation/devicetree/bindings/media/nxp,imx8mq-vpu.yaml new file mode 100644 index 000000000..195282628 --- /dev/null +++ b/Documentation/devicetree/bindings/media/nxp,imx8mq-vpu.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/nxp,imx8mq-vpu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Hantro G1/G2 VPU codecs implemented on i.MX8M SoCs + +maintainers: + - Philipp Zabel <p.zabel@pengutronix.de> + +description: + Hantro G1/G2 video decode accelerators present on i.MX8MQ SoCs. + +properties: + compatible: + oneOf: + - const: nxp,imx8mq-vpu + deprecated: true + - const: nxp,imx8mq-vpu-g1 + - const: nxp,imx8mq-vpu-g2 + - const: nxp,imx8mm-vpu-g1 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx8mq-clock.h> + #include <dt-bindings/power/imx8mq-power.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + video-codec@38300000 { + compatible = "nxp,imx8mq-vpu-g1"; + reg = <0x38300000 0x10000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MQ_CLK_VPU_G1_ROOT>; + power-domains = <&vpu_blk_ctrl IMX8MQ_VPUBLK_PD_G1>; + }; + - | + #include <dt-bindings/clock/imx8mq-clock.h> + #include <dt-bindings/power/imx8mq-power.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + video-codec@38300000 { + compatible = "nxp,imx8mq-vpu-g2"; + reg = <0x38310000 0x10000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MQ_CLK_VPU_G2_ROOT>; + power-domains = <&vpu_blk_ctrl IMX8MQ_VPUBLK_PD_G2>; + }; diff --git a/Documentation/devicetree/bindings/media/pxa-camera.txt b/Documentation/devicetree/bindings/media/pxa-camera.txt new file mode 100644 index 000000000..bc03ec096 --- /dev/null +++ b/Documentation/devicetree/bindings/media/pxa-camera.txt @@ -0,0 +1,42 @@ +Marvell PXA camera host interface + +Required properties: + - compatible: Should be "marvell,pxa270-qci" + - reg: register base and size + - interrupts: the interrupt number + - any required generic properties defined in video-interfaces.txt + +Optional properties: + - clocks: input clock (see clock-bindings.txt) + - clock-output-names: should contain the name of the clock driving the + sensor master clock MCLK + - clock-frequency: host interface is driving MCLK, and MCLK rate is this rate + +Example: + + pxa_camera: pxa_camera@50000000 { + compatible = "marvell,pxa270-qci"; + reg = <0x50000000 0x1000>; + interrupts = <33>; + + clocks = <&pxa2xx_clks 24>; + clock-names = "ciclk"; + clock-frequency = <50000000>; + clock-output-names = "qci_mclk"; + + + port { + #address-cells = <1>; + #size-cells = <0>; + + /* Parallel bus endpoint */ + qci: endpoint@0 { + reg = <0>; /* Local endpoint # */ + remote-endpoint = <&mt9m111_1>; + bus-width = <8>; /* Used data lines */ + hsync-active = <0>; /* Active low */ + vsync-active = <0>; /* Active low */ + pclk-sample = <1>; /* Rising */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,msm8916-camss.yaml b/Documentation/devicetree/bindings/media/qcom,msm8916-camss.yaml new file mode 100644 index 000000000..7c8e0a905 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,msm8916-camss.yaml @@ -0,0 +1,253 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,msm8916-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm CAMSS ISP + +maintainers: + - Robert Foss <robert.foss@linaro.org> + - Todor Tomov <todor.too@gmail.com> + +description: | + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms + +properties: + compatible: + const: qcom,msm8916-camss + + clocks: + minItems: 19 + maxItems: 19 + + clock-names: + items: + - const: top_ahb + - const: ispif_ahb + - const: csiphy0_timer + - const: csiphy1_timer + - const: csi0_ahb + - const: csi0 + - const: csi0_phy + - const: csi0_pix + - const: csi0_rdi + - const: csi1_ahb + - const: csi1 + - const: csi1_phy + - const: csi1_pix + - const: csi1_rdi + - const: ahb + - const: vfe0 + - const: csi_vfe0 + - const: vfe_ahb + - const: vfe_axi + + interrupts: + minItems: 6 + maxItems: 6 + + interrupt-names: + items: + - const: csiphy0 + - const: csiphy1 + - const: csid0 + - const: csid1 + - const: ispif + - const: vfe0 + + iommus: + maxItems: 1 + + power-domains: + items: + - description: VFE GDSC - Video Front End, Global Distributed Switch Controller. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: + An array of physical data lanes indexes. + Position of an entry determines the logical + lane number, while the value of an entry + indicates physical lane index. Lane swapping + is supported. Physical lane indexes; + 0, 2, 3, 4. + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + reg: + minItems: 9 + maxItems: 9 + + reg-names: + items: + - const: csiphy0 + - const: csiphy0_clk_mux + - const: csiphy1 + - const: csiphy1_clk_mux + - const: csid0 + - const: csid1 + - const: ispif + - const: csi_clk_mux + - const: vfe0 + + vdda-supply: + description: + Definition of the regulator used as analog power supply. + +required: + - clock-names + - clocks + - compatible + - interrupt-names + - interrupts + - iommus + - power-domains + - reg + - reg-names + - vdda-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-msm8916.h> + + camss: camss@1b0ac00 { + compatible = "qcom,msm8916-camss"; + + clocks = <&gcc GCC_CAMSS_TOP_AHB_CLK>, + <&gcc GCC_CAMSS_ISPIF_AHB_CLK>, + <&gcc GCC_CAMSS_CSI0PHYTIMER_CLK>, + <&gcc GCC_CAMSS_CSI1PHYTIMER_CLK>, + <&gcc GCC_CAMSS_CSI0_AHB_CLK>, + <&gcc GCC_CAMSS_CSI0_CLK>, + <&gcc GCC_CAMSS_CSI0PHY_CLK>, + <&gcc GCC_CAMSS_CSI0PIX_CLK>, + <&gcc GCC_CAMSS_CSI0RDI_CLK>, + <&gcc GCC_CAMSS_CSI1_AHB_CLK>, + <&gcc GCC_CAMSS_CSI1_CLK>, + <&gcc GCC_CAMSS_CSI1PHY_CLK>, + <&gcc GCC_CAMSS_CSI1PIX_CLK>, + <&gcc GCC_CAMSS_CSI1RDI_CLK>, + <&gcc GCC_CAMSS_AHB_CLK>, + <&gcc GCC_CAMSS_VFE0_CLK>, + <&gcc GCC_CAMSS_CSI_VFE0_CLK>, + <&gcc GCC_CAMSS_VFE_AHB_CLK>, + <&gcc GCC_CAMSS_VFE_AXI_CLK>; + + clock-names = "top_ahb", + "ispif_ahb", + "csiphy0_timer", + "csiphy1_timer", + "csi0_ahb", + "csi0", + "csi0_phy", + "csi0_pix", + "csi0_rdi", + "csi1_ahb", + "csi1", + "csi1_phy", + "csi1_pix", + "csi1_rdi", + "ahb", + "vfe0", + "csi_vfe0", + "vfe_ahb", + "vfe_axi"; + + interrupts = <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 51 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 52 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 55 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>; + + interrupt-names = "csiphy0", + "csiphy1", + "csid0", + "csid1", + "ispif", + "vfe0"; + + iommus = <&apps_iommu 3>; + + power-domains = <&gcc VFE_GDSC>; + + reg = <0x01b0ac00 0x200>, + <0x01b00030 0x4>, + <0x01b0b000 0x200>, + <0x01b00038 0x4>, + <0x01b08000 0x100>, + <0x01b08400 0x100>, + <0x01b0a000 0x500>, + <0x01b00020 0x10>, + <0x01b10000 0x1000>; + + reg-names = "csiphy0", + "csiphy0_clk_mux", + "csiphy1", + "csiphy1_clk_mux", + "csid0", + "csid1", + "ispif", + "csi_clk_mux", + "vfe0"; + + vdda-supply = <®_2v8>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + + }; diff --git a/Documentation/devicetree/bindings/media/qcom,msm8916-venus.yaml b/Documentation/devicetree/bindings/media/qcom,msm8916-venus.yaml new file mode 100644 index 000000000..da140c2e3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,msm8916-venus.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,msm8916-venus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm MSM8916 Venus video encode and decode accelerators + +maintainers: + - Stanimir Varbanov <stanimir.varbanov@linaro.org> + +description: | + The Venus IP is a video encode and decode accelerator present + on Qualcomm platforms + +allOf: + - $ref: qcom,venus-common.yaml# + +properties: + compatible: + const: qcom,msm8916-venus + + power-domains: + maxItems: 1 + + clocks: + maxItems: 3 + + clock-names: + items: + - const: core + - const: iface + - const: bus + + iommus: + maxItems: 1 + + video-decoder: + type: object + + properties: + compatible: + const: venus-decoder + + required: + - compatible + + deprecated: true + additionalProperties: false + + video-encoder: + type: object + + properties: + compatible: + const: venus-encoder + + required: + - compatible + + deprecated: true + additionalProperties: false + +required: + - compatible + - iommus + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-msm8916.h> + + video-codec@1d00000 { + compatible = "qcom,msm8916-venus"; + reg = <0x01d00000 0xff000>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_VENUS0_VCODEC0_CLK>, + <&gcc GCC_VENUS0_AHB_CLK>, + <&gcc GCC_VENUS0_AXI_CLK>; + clock-names = "core", "iface", "bus"; + power-domains = <&gcc VENUS_GDSC>; + iommus = <&apps_iommu 5>; + memory-region = <&venus_mem>; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,msm8939-camss.yaml b/Documentation/devicetree/bindings/media/qcom,msm8939-camss.yaml new file mode 100644 index 000000000..77b389d76 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,msm8939-camss.yaml @@ -0,0 +1,254 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,msm8939-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm MSM8939 Camera Subsystem (CAMSS) + +maintainers: + - Vincent Knecht <vincent.knecht@mailoo.org> + +description: + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms + +properties: + compatible: + const: qcom,msm8939-camss + + reg: + maxItems: 11 + + reg-names: + items: + - const: csiphy0 + - const: csiphy0_clk_mux + - const: csiphy1 + - const: csiphy1_clk_mux + - const: csid0 + - const: csid1 + - const: ispif + - const: csi_clk_mux + - const: vfe0 + - const: csid2 + - const: vfe0_vbif + + clocks: + maxItems: 24 + + clock-names: + items: + - const: top_ahb + - const: ispif_ahb + - const: csiphy0_timer + - const: csiphy1_timer + - const: csi0_ahb + - const: csi0 + - const: csi0_phy + - const: csi0_pix + - const: csi0_rdi + - const: csi1_ahb + - const: csi1 + - const: csi1_phy + - const: csi1_pix + - const: csi1_rdi + - const: ahb + - const: vfe0 + - const: csi_vfe0 + - const: vfe_ahb + - const: vfe_axi + - const: csi2_ahb + - const: csi2 + - const: csi2_phy + - const: csi2_pix + - const: csi2_rdi + + interrupts: + maxItems: 7 + + interrupt-names: + items: + - const: csiphy0 + - const: csiphy1 + - const: csid0 + - const: csid1 + - const: ispif + - const: vfe0 + - const: csid2 + + iommus: + maxItems: 1 + + power-domains: + items: + - description: VFE GDSC - Video Front End, Global Distributed Switch + Controller. + + vdda-supply: + description: + Definition of the regulator used as 1.2V analog power supply. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + patternProperties: + "^port@[0-1]$": + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interrupts + - interrupt-names + - iommus + - power-domains + - vdda-supply + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-msm8939.h> + + isp@1b0ac00 { + compatible = "qcom,msm8939-camss"; + + reg = <0x01b0ac00 0x200>, + <0x01b00030 0x4>, + <0x01b0b000 0x200>, + <0x01b00038 0x4>, + <0x01b08000 0x100>, + <0x01b08400 0x100>, + <0x01b0a000 0x500>, + <0x01b00020 0x10>, + <0x01b10000 0x1000>, + <0x01b08800 0x100>, + <0x01b40000 0x200>; + + reg-names = "csiphy0", + "csiphy0_clk_mux", + "csiphy1", + "csiphy1_clk_mux", + "csid0", + "csid1", + "ispif", + "csi_clk_mux", + "vfe0", + "csid2", + "vfe0_vbif"; + + clocks = <&gcc GCC_CAMSS_TOP_AHB_CLK>, + <&gcc GCC_CAMSS_ISPIF_AHB_CLK>, + <&gcc GCC_CAMSS_CSI0PHYTIMER_CLK>, + <&gcc GCC_CAMSS_CSI1PHYTIMER_CLK>, + <&gcc GCC_CAMSS_CSI0_AHB_CLK>, + <&gcc GCC_CAMSS_CSI0_CLK>, + <&gcc GCC_CAMSS_CSI0PHY_CLK>, + <&gcc GCC_CAMSS_CSI0PIX_CLK>, + <&gcc GCC_CAMSS_CSI0RDI_CLK>, + <&gcc GCC_CAMSS_CSI1_AHB_CLK>, + <&gcc GCC_CAMSS_CSI1_CLK>, + <&gcc GCC_CAMSS_CSI1PHY_CLK>, + <&gcc GCC_CAMSS_CSI1PIX_CLK>, + <&gcc GCC_CAMSS_CSI1RDI_CLK>, + <&gcc GCC_CAMSS_AHB_CLK>, + <&gcc GCC_CAMSS_VFE0_CLK>, + <&gcc GCC_CAMSS_CSI_VFE0_CLK>, + <&gcc GCC_CAMSS_VFE_AHB_CLK>, + <&gcc GCC_CAMSS_VFE_AXI_CLK>, + <&gcc GCC_CAMSS_CSI2_AHB_CLK>, + <&gcc GCC_CAMSS_CSI2_CLK>, + <&gcc GCC_CAMSS_CSI2PHY_CLK>, + <&gcc GCC_CAMSS_CSI2PIX_CLK>, + <&gcc GCC_CAMSS_CSI2RDI_CLK>; + + clock-names = "top_ahb", + "ispif_ahb", + "csiphy0_timer", + "csiphy1_timer", + "csi0_ahb", + "csi0", + "csi0_phy", + "csi0_pix", + "csi0_rdi", + "csi1_ahb", + "csi1", + "csi1_phy", + "csi1_pix", + "csi1_rdi", + "ahb", + "vfe0", + "csi_vfe0", + "vfe_ahb", + "vfe_axi", + "csi2_ahb", + "csi2", + "csi2_phy", + "csi2_pix", + "csi2_rdi"; + + interrupts = <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 51 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 52 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 55 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 153 IRQ_TYPE_EDGE_RISING>; + + interrupt-names = "csiphy0", + "csiphy1", + "csid0", + "csid1", + "ispif", + "vfe0", + "csid2"; + + iommus = <&apps_iommu 3>; + + power-domains = <&gcc VFE_GDSC>; + + vdda-supply = <®_1v2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + + csiphy1_ep: endpoint { + data-lanes = <0 2>; + remote-endpoint = <&sensor_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,msm8939-venus.yaml b/Documentation/devicetree/bindings/media/qcom,msm8939-venus.yaml new file mode 100644 index 000000000..10a50a410 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,msm8939-venus.yaml @@ -0,0 +1,79 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,msm8939-venus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm MSM8939 Venus video encode and decode accelerators + +maintainers: + - André Apitzsch <git@apitzsch.eu> + - Erikas Bitovtas <xerikasxx@gmail.com> + +description: + The Venus IP is a video encode and decode accelerator present + on Qualcomm platforms + +allOf: + - $ref: qcom,venus-common.yaml# + +properties: + compatible: + const: qcom,msm8939-venus + + power-domains: + maxItems: 3 + + power-domain-names: + items: + - const: venus + - const: vcodec0 + - const: vcodec1 + + clocks: + maxItems: 5 + + clock-names: + items: + - const: core + - const: iface + - const: bus + - const: vcodec0_core + - const: vcodec1_core + + iommus: + maxItems: 1 + +required: + - compatible + - iommus + - power-domain-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-msm8939.h> + + video-codec@1d00000 { + compatible = "qcom,msm8939-venus"; + reg = <0x01d00000 0xff000>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_VENUS0_VCODEC0_CLK>, + <&gcc GCC_VENUS0_AHB_CLK>, + <&gcc GCC_VENUS0_AXI_CLK>, + <&gcc GCC_VENUS0_CORE0_VCODEC0_CLK>, + <&gcc GCC_VENUS0_CORE1_VCODEC0_CLK>; + clock-names = "core", + "iface", + "bus", + "vcodec0_core", + "vcodec1_core"; + power-domains = <&gcc VENUS_GDSC>, + <&gcc VENUS_CORE0_GDSC>, + <&gcc VENUS_CORE1_GDSC>; + power-domain-names = "venus", "vcodec0", "vcodec1"; + iommus = <&apps_iommu 5>; + memory-region = <&venus_mem>; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,msm8953-camss.yaml b/Documentation/devicetree/bindings/media/qcom,msm8953-camss.yaml new file mode 100644 index 000000000..6d776b0ca --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,msm8953-camss.yaml @@ -0,0 +1,337 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,msm8953-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm MSM8953 Camera Subsystem (CAMSS) + +maintainers: + - Barnabas Czeman <barnabas.czeman@mainlining.org> + +description: + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms + +properties: + compatible: + const: qcom,msm8953-camss + + clocks: + minItems: 30 + maxItems: 30 + + clock-names: + items: + - const: ahb + - const: csi0 + - const: csi0_ahb + - const: csi0_phy + - const: csi0_pix + - const: csi0_rdi + - const: csi1 + - const: csi1_ahb + - const: csi1_phy + - const: csi1_pix + - const: csi1_rdi + - const: csi2 + - const: csi2_ahb + - const: csi2_phy + - const: csi2_pix + - const: csi2_rdi + - const: csi_vfe0 + - const: csi_vfe1 + - const: csiphy0_timer + - const: csiphy1_timer + - const: csiphy2_timer + - const: ispif_ahb + - const: micro_ahb + - const: top_ahb + - const: vfe0 + - const: vfe0_ahb + - const: vfe0_axi + - const: vfe1 + - const: vfe1_ahb + - const: vfe1_axi + + interrupts: + minItems: 9 + maxItems: 9 + + interrupt-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: ispif + - const: vfe0 + - const: vfe1 + + iommus: + maxItems: 1 + + power-domains: + items: + - description: VFE0 GDSC - Video Front End, Global Distributed Switch Controller. + - description: VFE1 GDSC - Video Front End, Global Distributed Switch Controller. + + power-domain-names: + items: + - const: vfe0 + - const: vfe1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: + An array of physical data lanes indexes. + Position of an entry determines the logical + lane number, while the value of an entry + indicates physical lane index. Lane swapping + is supported. Physical lane indexes; + 0, 2, 3, 4. + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + reg: + minItems: 13 + maxItems: 13 + + reg-names: + items: + - const: csi_clk_mux + - const: csid0 + - const: csid1 + - const: csid2 + - const: csiphy0 + - const: csiphy0_clk_mux + - const: csiphy1 + - const: csiphy1_clk_mux + - const: csiphy2 + - const: csiphy2_clk_mux + - const: ispif + - const: vfe0 + - const: vfe1 + + vdda-supply: + description: + Definition of the regulator used as analog power supply. + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interrupts + - interrupt-names + - iommus + - power-domains + - power-domain-names + - vdda-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-msm8953.h> + + camss: camss@1b00020 { + compatible = "qcom,msm8953-camss"; + + reg = <0x1b00020 0x10>, + <0x1b30000 0x100>, + <0x1b30400 0x100>, + <0x1b30800 0x100>, + <0x1b34000 0x1000>, + <0x1b00030 0x4>, + <0x1b35000 0x1000>, + <0x1b00038 0x4>, + <0x1b36000 0x1000>, + <0x1b00040 0x4>, + <0x1b31000 0x500>, + <0x1b10000 0x1000>, + <0x1b14000 0x1000>; + reg-names = "csi_clk_mux", + "csid0", + "csid1", + "csid2", + "csiphy0", + "csiphy0_clk_mux", + "csiphy1", + "csiphy1_clk_mux", + "csiphy2", + "csiphy2_clk_mux", + "ispif", + "vfe0", + "vfe1"; + + clocks = <&gcc GCC_CAMSS_AHB_CLK>, + <&gcc GCC_CAMSS_CSI0_CLK>, + <&gcc GCC_CAMSS_CSI0_AHB_CLK>, + <&gcc GCC_CAMSS_CSI0PHY_CLK>, + <&gcc GCC_CAMSS_CSI0PIX_CLK>, + <&gcc GCC_CAMSS_CSI0RDI_CLK>, + <&gcc GCC_CAMSS_CSI1_CLK>, + <&gcc GCC_CAMSS_CSI1_AHB_CLK>, + <&gcc GCC_CAMSS_CSI1PHY_CLK>, + <&gcc GCC_CAMSS_CSI1PIX_CLK>, + <&gcc GCC_CAMSS_CSI1RDI_CLK>, + <&gcc GCC_CAMSS_CSI2_CLK>, + <&gcc GCC_CAMSS_CSI2_AHB_CLK>, + <&gcc GCC_CAMSS_CSI2PHY_CLK>, + <&gcc GCC_CAMSS_CSI2PIX_CLK>, + <&gcc GCC_CAMSS_CSI2RDI_CLK>, + <&gcc GCC_CAMSS_CSI_VFE0_CLK>, + <&gcc GCC_CAMSS_CSI_VFE1_CLK>, + <&gcc GCC_CAMSS_CSI0PHYTIMER_CLK>, + <&gcc GCC_CAMSS_CSI1PHYTIMER_CLK>, + <&gcc GCC_CAMSS_CSI2PHYTIMER_CLK>, + <&gcc GCC_CAMSS_ISPIF_AHB_CLK>, + <&gcc GCC_CAMSS_MICRO_AHB_CLK>, + <&gcc GCC_CAMSS_TOP_AHB_CLK>, + <&gcc GCC_CAMSS_VFE0_CLK>, + <&gcc GCC_CAMSS_VFE0_AHB_CLK>, + <&gcc GCC_CAMSS_VFE0_AXI_CLK>, + <&gcc GCC_CAMSS_VFE1_CLK>, + <&gcc GCC_CAMSS_VFE1_AHB_CLK>, + <&gcc GCC_CAMSS_VFE1_AXI_CLK>; + clock-names = "ahb", + "csi0", + "csi0_ahb", + "csi0_phy", + "csi0_pix", + "csi0_rdi", + "csi1", + "csi1_ahb", + "csi1_phy", + "csi1_pix", + "csi1_rdi", + "csi2", + "csi2_ahb", + "csi2_phy", + "csi2_pix", + "csi2_rdi", + "csi_vfe0", + "csi_vfe1", + "csiphy0_timer", + "csiphy1_timer", + "csiphy2_timer", + "ispif_ahb", + "micro_ahb", + "top_ahb", + "vfe0", + "vfe0_ahb", + "vfe0_axi", + "vfe1", + "vfe1_ahb", + "vfe1_axi"; + + interrupts = <GIC_SPI 51 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 52 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 153 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 315 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 55 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 29 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "csid0", + "csid1", + "csid2", + "csiphy0", + "csiphy1", + "csiphy2", + "ispif", + "vfe0", + "vfe1"; + + iommus = <&apps_iommu 0x14>; + + power-domains = <&gcc VFE0_GDSC>, + <&gcc VFE1_GDSC>; + power-domain-names = "vfe0", "vfe1"; + + vdda-supply = <®_2v8>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,msm8996-camss.yaml b/Documentation/devicetree/bindings/media/qcom,msm8996-camss.yaml new file mode 100644 index 000000000..a2025952f --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,msm8996-camss.yaml @@ -0,0 +1,386 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,msm8996-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm CAMSS ISP + +maintainers: + - Robert Foss <robert.foss@linaro.org> + - Todor Tomov <todor.too@gmail.com> + +description: | + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms + +properties: + compatible: + const: qcom,msm8996-camss + + clocks: + minItems: 36 + maxItems: 36 + + clock-names: + items: + - const: top_ahb + - const: ispif_ahb + - const: csiphy0_timer + - const: csiphy1_timer + - const: csiphy2_timer + - const: csi0_ahb + - const: csi0 + - const: csi0_phy + - const: csi0_pix + - const: csi0_rdi + - const: csi1_ahb + - const: csi1 + - const: csi1_phy + - const: csi1_pix + - const: csi1_rdi + - const: csi2_ahb + - const: csi2 + - const: csi2_phy + - const: csi2_pix + - const: csi2_rdi + - const: csi3_ahb + - const: csi3 + - const: csi3_phy + - const: csi3_pix + - const: csi3_rdi + - const: ahb + - const: vfe0 + - const: csi_vfe0 + - const: vfe0_ahb + - const: vfe0_stream + - const: vfe1 + - const: csi_vfe1 + - const: vfe1_ahb + - const: vfe1_stream + - const: vfe_ahb + - const: vfe_axi + + interrupts: + minItems: 10 + maxItems: 10 + + interrupt-names: + items: + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid3 + - const: ispif + - const: vfe0 + - const: vfe1 + + iommus: + maxItems: 4 + + power-domains: + items: + - description: VFE0 GDSC - Video Front End, Global Distributed Switch Controller. + - description: VFE1 GDSC - Video Front End, Global Distributed Switch Controller. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: + An array of physical data lanes indexes. + Position of an entry determines the logical + lane number, while the value of an entry + indicates physical lane index. Lane swapping + is supported. Physical lane indexes are; + 0, 1, 2, 3 + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + port@3: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + reg: + minItems: 14 + maxItems: 14 + + reg-names: + items: + - const: csiphy0 + - const: csiphy0_clk_mux + - const: csiphy1 + - const: csiphy1_clk_mux + - const: csiphy2 + - const: csiphy2_clk_mux + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid3 + - const: ispif + - const: csi_clk_mux + - const: vfe0 + - const: vfe1 + + vdda-supply: + description: + Definition of the regulator used as analog power supply. + +required: + - clock-names + - clocks + - compatible + - interrupt-names + - interrupts + - iommus + - power-domains + - reg + - reg-names + - vdda-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-msm8996.h> + #include <dt-bindings/clock/qcom,mmcc-msm8996.h> + + camss: camss@a34000 { + compatible = "qcom,msm8996-camss"; + + clocks = <&mmcc CAMSS_TOP_AHB_CLK>, + <&mmcc CAMSS_ISPIF_AHB_CLK>, + <&mmcc CAMSS_CSI0PHYTIMER_CLK>, + <&mmcc CAMSS_CSI1PHYTIMER_CLK>, + <&mmcc CAMSS_CSI2PHYTIMER_CLK>, + <&mmcc CAMSS_CSI0_AHB_CLK>, + <&mmcc CAMSS_CSI0_CLK>, + <&mmcc CAMSS_CSI0PHY_CLK>, + <&mmcc CAMSS_CSI0PIX_CLK>, + <&mmcc CAMSS_CSI0RDI_CLK>, + <&mmcc CAMSS_CSI1_AHB_CLK>, + <&mmcc CAMSS_CSI1_CLK>, + <&mmcc CAMSS_CSI1PHY_CLK>, + <&mmcc CAMSS_CSI1PIX_CLK>, + <&mmcc CAMSS_CSI1RDI_CLK>, + <&mmcc CAMSS_CSI2_AHB_CLK>, + <&mmcc CAMSS_CSI2_CLK>, + <&mmcc CAMSS_CSI2PHY_CLK>, + <&mmcc CAMSS_CSI2PIX_CLK>, + <&mmcc CAMSS_CSI2RDI_CLK>, + <&mmcc CAMSS_CSI3_AHB_CLK>, + <&mmcc CAMSS_CSI3_CLK>, + <&mmcc CAMSS_CSI3PHY_CLK>, + <&mmcc CAMSS_CSI3PIX_CLK>, + <&mmcc CAMSS_CSI3RDI_CLK>, + <&mmcc CAMSS_AHB_CLK>, + <&mmcc CAMSS_VFE0_CLK>, + <&mmcc CAMSS_CSI_VFE0_CLK>, + <&mmcc CAMSS_VFE0_AHB_CLK>, + <&mmcc CAMSS_VFE0_STREAM_CLK>, + <&mmcc CAMSS_VFE1_CLK>, + <&mmcc CAMSS_CSI_VFE1_CLK>, + <&mmcc CAMSS_VFE1_AHB_CLK>, + <&mmcc CAMSS_VFE1_STREAM_CLK>, + <&mmcc CAMSS_VFE_AHB_CLK>, + <&mmcc CAMSS_VFE_AXI_CLK>; + + clock-names = "top_ahb", + "ispif_ahb", + "csiphy0_timer", + "csiphy1_timer", + "csiphy2_timer", + "csi0_ahb", + "csi0", + "csi0_phy", + "csi0_pix", + "csi0_rdi", + "csi1_ahb", + "csi1", + "csi1_phy", + "csi1_pix", + "csi1_rdi", + "csi2_ahb", + "csi2", + "csi2_phy", + "csi2_pix", + "csi2_rdi", + "csi3_ahb", + "csi3", + "csi3_phy", + "csi3_pix", + "csi3_rdi", + "ahb", + "vfe0", + "csi_vfe0", + "vfe0_ahb", + "vfe0_stream", + "vfe1", + "csi_vfe1", + "vfe1_ahb", + "vfe1_stream", + "vfe_ahb", + "vfe_axi"; + + interrupts = <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 80 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 296 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 297 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 298 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 299 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 309 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 314 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 315 IRQ_TYPE_EDGE_RISING>; + + interrupt-names = "csiphy0", + "csiphy1", + "csiphy2", + "csid0", + "csid1", + "csid2", + "csid3", + "ispif", + "vfe0", + "vfe1"; + + iommus = <&vfe_smmu 0>, + <&vfe_smmu 1>, + <&vfe_smmu 2>, + <&vfe_smmu 3>; + + power-domains = <&mmcc VFE0_GDSC>, + <&mmcc VFE1_GDSC>; + + reg = <0x00a34000 0x1000>, + <0x00a00030 0x4>, + <0x00a35000 0x1000>, + <0x00a00038 0x4>, + <0x00a36000 0x1000>, + <0x00a00040 0x4>, + <0x00a30000 0x100>, + <0x00a30400 0x100>, + <0x00a30800 0x100>, + <0x00a30c00 0x100>, + <0x00a31000 0x500>, + <0x00a00020 0x10>, + <0x00a10000 0x1000>, + <0x00a14000 0x1000>; + + reg-names = "csiphy0", + "csiphy0_clk_mux", + "csiphy1", + "csiphy1_clk_mux", + "csiphy2", + "csiphy2_clk_mux", + "csid0", + "csid1", + "csid2", + "csid3", + "ispif", + "csi_clk_mux", + "vfe0", + "vfe1"; + + vdda-supply = <®_2v8>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,msm8996-venus.yaml b/Documentation/devicetree/bindings/media/qcom,msm8996-venus.yaml new file mode 100644 index 000000000..56c16458e --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,msm8996-venus.yaml @@ -0,0 +1,157 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,msm8996-venus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm MSM8996 Venus video encode and decode accelerators + +maintainers: + - Stanimir Varbanov <stanimir.varbanov@linaro.org> + +description: | + The Venus IP is a video encode and decode accelerator present + on Qualcomm platforms + +allOf: + - $ref: qcom,venus-common.yaml# + +properties: + compatible: + enum: + - qcom,msm8996-venus + - qcom,msm8998-venus + + power-domains: + maxItems: 1 + + clocks: + maxItems: 4 + + clock-names: + items: + - const: core + - const: iface + - const: bus + - const: mbus + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: video-mem + - const: cpu-cfg + + iommus: + maxItems: 20 + + video-decoder: + type: object + + properties: + compatible: + const: venus-decoder + + clocks: + maxItems: 1 + + clock-names: + items: + - const: core + + power-domains: + maxItems: 1 + + required: + - compatible + - clocks + - clock-names + - power-domains + + additionalProperties: false + + video-encoder: + type: object + + properties: + compatible: + const: venus-encoder + + clocks: + maxItems: 1 + + clock-names: + items: + - const: core + + power-domains: + maxItems: 1 + + required: + - compatible + - clocks + - clock-names + - power-domains + + additionalProperties: false + +required: + - compatible + - iommus + - video-decoder + - video-encoder + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,mmcc-msm8996.h> + + video-codec@c00000 { + compatible = "qcom,msm8996-venus"; + reg = <0x00c00000 0xff000>; + interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mmcc VIDEO_CORE_CLK>, + <&mmcc VIDEO_AHB_CLK>, + <&mmcc VIDEO_AXI_CLK>, + <&mmcc VIDEO_MAXI_CLK>; + clock-names = "core", "iface", "bus", "mbus"; + power-domains = <&mmcc VENUS_GDSC>; + iommus = <&venus_smmu 0x00>, + <&venus_smmu 0x01>, + <&venus_smmu 0x0a>, + <&venus_smmu 0x07>, + <&venus_smmu 0x0e>, + <&venus_smmu 0x0f>, + <&venus_smmu 0x08>, + <&venus_smmu 0x09>, + <&venus_smmu 0x0b>, + <&venus_smmu 0x0c>, + <&venus_smmu 0x0d>, + <&venus_smmu 0x10>, + <&venus_smmu 0x11>, + <&venus_smmu 0x21>, + <&venus_smmu 0x28>, + <&venus_smmu 0x29>, + <&venus_smmu 0x2b>, + <&venus_smmu 0x2c>, + <&venus_smmu 0x2d>, + <&venus_smmu 0x31>; + memory-region = <&venus_mem>; + + video-decoder { + compatible = "venus-decoder"; + clocks = <&mmcc VIDEO_SUBCORE0_CLK>; + clock-names = "core"; + power-domains = <&mmcc VENUS_CORE0_GDSC>; + }; + + video-encoder { + compatible = "venus-encoder"; + clocks = <&mmcc VIDEO_SUBCORE1_CLK>; + clock-names = "core"; + power-domains = <&mmcc VENUS_CORE1_GDSC>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,qcm2290-camss.yaml b/Documentation/devicetree/bindings/media/qcom,qcm2290-camss.yaml new file mode 100644 index 000000000..391d0f6f6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,qcm2290-camss.yaml @@ -0,0 +1,243 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,qcm2290-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm QCM2290 Camera Subsystem (CAMSS) + +maintainers: + - Loic Poulain <loic.poulain@oss.qualcomm.com> + +description: + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms. + +properties: + compatible: + const: qcom,qcm2290-camss + + reg: + maxItems: 9 + + reg-names: + items: + - const: top + - const: csid0 + - const: csid1 + - const: csiphy0 + - const: csiphy1 + - const: csitpg0 + - const: csitpg1 + - const: vfe0 + - const: vfe1 + + clocks: + maxItems: 15 + + clock-names: + items: + - const: ahb + - const: axi + - const: camnoc_nrt_axi + - const: camnoc_rt_axi + - const: csi0 + - const: csi1 + - const: csiphy0 + - const: csiphy0_timer + - const: csiphy1 + - const: csiphy1_timer + - const: top_ahb + - const: vfe0 + - const: vfe0_cphy_rx + - const: vfe1 + - const: vfe1_cphy_rx + + interrupts: + maxItems: 8 + + interrupt-names: + items: + - const: csid0 + - const: csid1 + - const: csiphy0 + - const: csiphy1 + - const: csitpg0 + - const: csitpg1 + - const: vfe0 + - const: vfe1 + + interconnects: + maxItems: 3 + + interconnect-names: + items: + - const: ahb + - const: hf_mnoc + - const: sf_mnoc + + iommus: + maxItems: 4 + + power-domains: + items: + - description: GDSC CAMSS Block, Global Distributed Switch Controller. + + vdd-csiphy-1p2-supply: + description: + Phandle to a 1.2V regulator supply to CSI PHYs. + + vdd-csiphy-1p8-supply: + description: + Phandle to 1.8V regulator supply to CSI PHYs pll block. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + patternProperties: + "^port@[0-3]+$": + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + description: + Input port for receiving CSI data from a CSIPHY. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interrupts + - interrupt-names + - interconnects + - interconnect-names + - iommus + - power-domains + - vdd-csiphy-1p2-supply + - vdd-csiphy-1p8-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-qcm2290.h> + #include <dt-bindings/interconnect/qcom,rpm-icc.h> + #include <dt-bindings/interconnect/qcom,qcm2290.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + camss: camss@5c6e000 { + compatible = "qcom,qcm2290-camss"; + + reg = <0x0 0x5c11000 0x0 0x1000>, + <0x0 0x5c6e000 0x0 0x1000>, + <0x0 0x5c75000 0x0 0x1000>, + <0x0 0x5c52000 0x0 0x1000>, + <0x0 0x5c53000 0x0 0x1000>, + <0x0 0x5c66000 0x0 0x400>, + <0x0 0x5c68000 0x0 0x400>, + <0x0 0x5c6f000 0x0 0x4000>, + <0x0 0x5c76000 0x0 0x4000>; + reg-names = "top", + "csid0", + "csid1", + "csiphy0", + "csiphy1", + "csitpg0", + "csitpg1", + "vfe0", + "vfe1"; + + clocks = <&gcc GCC_CAMERA_AHB_CLK>, + <&gcc GCC_CAMSS_AXI_CLK>, + <&gcc GCC_CAMSS_NRT_AXI_CLK>, + <&gcc GCC_CAMSS_RT_AXI_CLK>, + <&gcc GCC_CAMSS_TFE_0_CSID_CLK>, + <&gcc GCC_CAMSS_TFE_1_CSID_CLK>, + <&gcc GCC_CAMSS_CPHY_0_CLK>, + <&gcc GCC_CAMSS_CSI0PHYTIMER_CLK>, + <&gcc GCC_CAMSS_CPHY_1_CLK>, + <&gcc GCC_CAMSS_CSI1PHYTIMER_CLK>, + <&gcc GCC_CAMSS_TOP_AHB_CLK>, + <&gcc GCC_CAMSS_TFE_0_CLK>, + <&gcc GCC_CAMSS_TFE_0_CPHY_RX_CLK>, + <&gcc GCC_CAMSS_TFE_1_CLK>, + <&gcc GCC_CAMSS_TFE_1_CPHY_RX_CLK>; + clock-names = "ahb", + "axi", + "camnoc_nrt_axi", + "camnoc_rt_axi", + "csi0", + "csi1", + "csiphy0", + "csiphy0_timer", + "csiphy1", + "csiphy1_timer", + "top_ahb", + "vfe0", + "vfe0_cphy_rx", + "vfe1", + "vfe1_cphy_rx"; + + interrupts = <GIC_SPI 210 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 212 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 72 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 73 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 309 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 310 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 211 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 213 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "csid0", + "csid1", + "csiphy0", + "csiphy1", + "csitpg0", + "csitpg1", + "vfe0", + "vfe1"; + + interconnects = <&bimc MASTER_APPSS_PROC RPM_ACTIVE_TAG + &config_noc SLAVE_CAMERA_CFG RPM_ACTIVE_TAG>, + <&mmrt_virt MASTER_CAMNOC_HF RPM_ALWAYS_TAG + &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>, + <&mmnrt_virt MASTER_CAMNOC_SF RPM_ALWAYS_TAG + &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>; + interconnect-names = "ahb", + "hf_mnoc", + "sf_mnoc"; + + iommus = <&apps_smmu 0x400 0x0>, + <&apps_smmu 0x800 0x0>, + <&apps_smmu 0x820 0x0>, + <&apps_smmu 0x840 0x0>; + + power-domains = <&gcc GCC_CAMSS_TOP_GDSC>; + + vdd-csiphy-1p2-supply = <&pm4125_l5>; + vdd-csiphy-1p8-supply = <&pm4125_l13>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,qcm2290-venus.yaml b/Documentation/devicetree/bindings/media/qcom,qcm2290-venus.yaml new file mode 100644 index 000000000..5977e7d0a --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,qcm2290-venus.yaml @@ -0,0 +1,131 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,qcm2290-venus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm QCM2290 Venus video encode and decode accelerators + +maintainers: + - Jorge Ramirez-Ortiz <jorge.ramirez@oss.qualcomm.com> + +description: + The Venus AR50_LITE IP is a video encode and decode accelerator present + on Qualcomm platforms. + +allOf: + - $ref: qcom,venus-common.yaml# + +properties: + compatible: + oneOf: + - items: + - const: qcom,sm6115-venus + - const: qcom,qcm2290-venus + - const: qcom,qcm2290-venus + + power-domains: + maxItems: 3 + + power-domain-names: + items: + - const: venus + - const: vcodec0 + - const: cx + + clocks: + maxItems: 6 + + clock-names: + items: + - const: core + - const: iface + - const: bus + - const: throttle + - const: vcodec0_core + - const: vcodec0_bus + + iommus: + maxItems: 2 + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: video-mem + - const: cpu-cfg + + operating-points-v2: true + opp-table: + type: object + +required: + - compatible + - power-domain-names + - iommus + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-qcm2290.h> + #include <dt-bindings/interconnect/qcom,qcm2290.h> + #include <dt-bindings/interconnect/qcom,rpm-icc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + venus: video-codec@5a00000 { + compatible = "qcom,qcm2290-venus"; + reg = <0x5a00000 0xf0000>; + + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; + + power-domains = <&gcc GCC_VENUS_GDSC>, + <&gcc GCC_VCODEC0_GDSC>, + <&rpmpd QCM2290_VDDCX>; + power-domain-names = "venus", + "vcodec0", + "cx"; + + operating-points-v2 = <&venus_opp_table>; + + clocks = <&gcc GCC_VIDEO_VENUS_CTL_CLK>, + <&gcc GCC_VIDEO_AHB_CLK>, + <&gcc GCC_VENUS_CTL_AXI_CLK>, + <&gcc GCC_VIDEO_THROTTLE_CORE_CLK>, + <&gcc GCC_VIDEO_VCODEC0_SYS_CLK>, + <&gcc GCC_VCODEC0_AXI_CLK>; + clock-names = "core", + "iface", + "bus", + "throttle", + "vcodec0_core", + "vcodec0_bus"; + + memory-region = <&pil_video_mem>; + + iommus = <&apps_smmu 0x860 0x0>, + <&apps_smmu 0x880 0x0>; + + interconnects = <&mmnrt_virt MASTER_VIDEO_P0 RPM_ALWAYS_TAG + &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>, + <&bimc MASTER_APPSS_PROC RPM_ACTIVE_TAG + &config_noc SLAVE_VENUS_CFG RPM_ACTIVE_TAG>; + interconnect-names = "video-mem", + "cpu-cfg"; + + venus_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-133333333 { + opp-hz = /bits/ 64 <133333333>; + required-opps = <&rpmpd_opp_low_svs>; + }; + + opp-240000000 { + opp-hz = /bits/ 64 <240000000>; + required-opps = <&rpmpd_opp_svs>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,qcs8300-camss.yaml b/Documentation/devicetree/bindings/media/qcom,qcs8300-camss.yaml new file mode 100644 index 000000000..e5f170aa4 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,qcs8300-camss.yaml @@ -0,0 +1,349 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,qcs8300-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm QCS8300 CAMSS ISP + +maintainers: + - Vikram Sharma <quic_vikramsa@quicinc.com> + +description: + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms. + +properties: + compatible: + const: qcom,qcs8300-camss + + reg: + maxItems: 21 + + reg-names: + items: + - const: csid_wrapper + - const: csid0 + - const: csid1 + - const: csid_lite0 + - const: csid_lite1 + - const: csid_lite2 + - const: csid_lite3 + - const: csid_lite4 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: tpg0 + - const: tpg1 + - const: tpg2 + - const: vfe0 + - const: vfe1 + - const: vfe_lite0 + - const: vfe_lite1 + - const: vfe_lite2 + - const: vfe_lite3 + - const: vfe_lite4 + + clocks: + maxItems: 26 + + clock-names: + items: + - const: camnoc_axi + - const: core_ahb + - const: cpas_ahb + - const: cpas_fast_ahb_clk + - const: cpas_vfe_lite + - const: cpas_vfe0 + - const: cpas_vfe1 + - const: csid + - const: csiphy0 + - const: csiphy0_timer + - const: csiphy1 + - const: csiphy1_timer + - const: csiphy2 + - const: csiphy2_timer + - const: csiphy_rx + - const: gcc_axi_hf + - const: gcc_axi_sf + - const: icp_ahb + - const: vfe0 + - const: vfe0_fast_ahb + - const: vfe1 + - const: vfe1_fast_ahb + - const: vfe_lite + - const: vfe_lite_ahb + - const: vfe_lite_cphy_rx + - const: vfe_lite_csid + + interrupts: + maxItems: 20 + + interrupt-names: + items: + - const: csid0 + - const: csid1 + - const: csid_lite0 + - const: csid_lite1 + - const: csid_lite2 + - const: csid_lite3 + - const: csid_lite4 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: tpg0 + - const: tpg1 + - const: tpg2 + - const: vfe0 + - const: vfe1 + - const: vfe_lite0 + - const: vfe_lite1 + - const: vfe_lite2 + - const: vfe_lite3 + - const: vfe_lite4 + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: ahb + - const: hf_0 + + iommus: + maxItems: 1 + + power-domains: + items: + - description: Titan GDSC - Titan ISP Block, Global Distributed Switch Controller. + + power-domain-names: + items: + - const: top + + vdda-phy-supply: + description: + Phandle to a 0.88V regulator supply to CSI PHYs. + + vdda-pll-supply: + description: + Phandle to 1.2V regulator supply to CSI PHYs pll block. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + patternProperties: + "^port@[0-2]+$": + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSIPHY 0-2. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interrupts + - interrupt-names + - interconnects + - interconnect-names + - iommus + - power-domains + - power-domain-names + - ports + - vdda-phy-supply + - vdda-pll-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,sa8775p-camcc.h> + #include <dt-bindings/clock/qcom,sa8775p-gcc.h> + #include <dt-bindings/interconnect/qcom,sa8775p-rpmh.h> + #include <dt-bindings/interconnect/qcom,icc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + isp@ac78000 { + compatible = "qcom,qcs8300-camss"; + + reg = <0x0 0xac78000 0x0 0x1000>, + <0x0 0xac7a000 0x0 0x0f00>, + <0x0 0xac7c000 0x0 0x0f00>, + <0x0 0xac84000 0x0 0x0f00>, + <0x0 0xac88000 0x0 0x0f00>, + <0x0 0xac8c000 0x0 0x0f00>, + <0x0 0xac90000 0x0 0x0f00>, + <0x0 0xac94000 0x0 0x0f00>, + <0x0 0xac9c000 0x0 0x2000>, + <0x0 0xac9e000 0x0 0x2000>, + <0x0 0xaca0000 0x0 0x2000>, + <0x0 0xacac000 0x0 0x0400>, + <0x0 0xacad000 0x0 0x0400>, + <0x0 0xacae000 0x0 0x0400>, + <0x0 0xac4d000 0x0 0xd000>, + <0x0 0xac60000 0x0 0xd000>, + <0x0 0xac85000 0x0 0x0d00>, + <0x0 0xac89000 0x0 0x0d00>, + <0x0 0xac8d000 0x0 0x0d00>, + <0x0 0xac91000 0x0 0x0d00>, + <0x0 0xac95000 0x0 0x0d00>; + reg-names = "csid_wrapper", + "csid0", + "csid1", + "csid_lite0", + "csid_lite1", + "csid_lite2", + "csid_lite3", + "csid_lite4", + "csiphy0", + "csiphy1", + "csiphy2", + "tpg0", + "tpg1", + "tpg2", + "vfe0", + "vfe1", + "vfe_lite0", + "vfe_lite1", + "vfe_lite2", + "vfe_lite3", + "vfe_lite4"; + + clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>, + <&camcc CAM_CC_CORE_AHB_CLK>, + <&camcc CAM_CC_CPAS_AHB_CLK>, + <&camcc CAM_CC_CPAS_FAST_AHB_CLK>, + <&camcc CAM_CC_CPAS_IFE_LITE_CLK>, + <&camcc CAM_CC_CPAS_IFE_0_CLK>, + <&camcc CAM_CC_CPAS_IFE_1_CLK>, + <&camcc CAM_CC_CSID_CLK>, + <&camcc CAM_CC_CSIPHY0_CLK>, + <&camcc CAM_CC_CSI0PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY1_CLK>, + <&camcc CAM_CC_CSI1PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY2_CLK>, + <&camcc CAM_CC_CSI2PHYTIMER_CLK>, + <&camcc CAM_CC_CSID_CSIPHY_RX_CLK>, + <&gcc GCC_CAMERA_HF_AXI_CLK>, + <&gcc GCC_CAMERA_SF_AXI_CLK>, + <&camcc CAM_CC_ICP_AHB_CLK>, + <&camcc CAM_CC_IFE_0_CLK>, + <&camcc CAM_CC_IFE_0_FAST_AHB_CLK>, + <&camcc CAM_CC_IFE_1_CLK>, + <&camcc CAM_CC_IFE_1_FAST_AHB_CLK>, + <&camcc CAM_CC_IFE_LITE_CLK>, + <&camcc CAM_CC_IFE_LITE_AHB_CLK>, + <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_LITE_CSID_CLK>; + clock-names = "camnoc_axi", + "core_ahb", + "cpas_ahb", + "cpas_fast_ahb_clk", + "cpas_vfe_lite", + "cpas_vfe0", + "cpas_vfe1", + "csid", + "csiphy0", + "csiphy0_timer", + "csiphy1", + "csiphy1_timer", + "csiphy2", + "csiphy2_timer", + "csiphy_rx", + "gcc_axi_hf", + "gcc_axi_sf", + "icp_ahb", + "vfe0", + "vfe0_fast_ahb", + "vfe1", + "vfe1_fast_ahb", + "vfe_lite", + "vfe_lite_ahb", + "vfe_lite_cphy_rx", + "vfe_lite_csid"; + + interrupts = <GIC_SPI 565 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 564 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 359 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 759 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 758 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 604 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 545 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 546 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 547 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 360 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 761 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 760 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 605 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "csid0", + "csid1", + "csid_lite0", + "csid_lite1", + "csid_lite2", + "csid_lite3", + "csid_lite4", + "csiphy0", + "csiphy1", + "csiphy2", + "tpg0", + "tpg1", + "tpg2", + "vfe0", + "vfe1", + "vfe_lite0", + "vfe_lite1", + "vfe_lite2", + "vfe_lite3", + "vfe_lite4"; + + interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY + &config_noc SLAVE_CAMERA_CFG QCOM_ICC_TAG_ACTIVE_ONLY>, + <&mmss_noc MASTER_CAMNOC_HF QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "ahb", + "hf_0"; + + iommus = <&apps_smmu 0x2400 0x20>; + + power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>; + power-domain-names = "top"; + + vdda-phy-supply = <&vreg_l4a_0p88>; + vdda-pll-supply = <&vreg_l1c_1p2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sa8775p-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sa8775p-camss.yaml new file mode 100644 index 000000000..48f280e99 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sa8775p-camss.yaml @@ -0,0 +1,361 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sa8775p-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SA8775P CAMSS ISP + +maintainers: + - Vikram Sharma <quic_vikramsa@quicinc.com> + +description: + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms. + +properties: + compatible: + const: qcom,sa8775p-camss + + reg: + maxItems: 22 + + reg-names: + items: + - const: csid_wrapper + - const: csid0 + - const: csid1 + - const: csid_lite0 + - const: csid_lite1 + - const: csid_lite2 + - const: csid_lite3 + - const: csid_lite4 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: tpg0 + - const: tpg1 + - const: tpg2 + - const: vfe0 + - const: vfe1 + - const: vfe_lite0 + - const: vfe_lite1 + - const: vfe_lite2 + - const: vfe_lite3 + - const: vfe_lite4 + + clocks: + maxItems: 28 + + clock-names: + items: + - const: camnoc_axi + - const: core_ahb + - const: cpas_ahb + - const: cpas_fast_ahb_clk + - const: cpas_vfe_lite + - const: cpas_vfe0 + - const: cpas_vfe1 + - const: csid + - const: csiphy0 + - const: csiphy0_timer + - const: csiphy1 + - const: csiphy1_timer + - const: csiphy2 + - const: csiphy2_timer + - const: csiphy3 + - const: csiphy3_timer + - const: csiphy_rx + - const: gcc_axi_hf + - const: gcc_axi_sf + - const: icp_ahb + - const: vfe0 + - const: vfe0_fast_ahb + - const: vfe1 + - const: vfe1_fast_ahb + - const: vfe_lite + - const: vfe_lite_ahb + - const: vfe_lite_cphy_rx + - const: vfe_lite_csid + + interrupts: + maxItems: 21 + + interrupt-names: + items: + - const: csid0 + - const: csid1 + - const: csid_lite0 + - const: csid_lite1 + - const: csid_lite2 + - const: csid_lite3 + - const: csid_lite4 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: tpg0 + - const: tpg1 + - const: tpg2 + - const: vfe0 + - const: vfe1 + - const: vfe_lite0 + - const: vfe_lite1 + - const: vfe_lite2 + - const: vfe_lite3 + - const: vfe_lite4 + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: ahb + - const: hf_0 + + iommus: + maxItems: 1 + + power-domains: + items: + - description: Titan GDSC - Titan ISP Block, Global Distributed Switch Controller. + + power-domain-names: + items: + - const: top + + vdda-phy-supply: + description: + 0.88V supply to CSIPHY IP blocks. + + vdda-pll-supply: + description: + 1.2V supply to CSIPHY IP blocks. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + patternProperties: + "^port@[0-3]+$": + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSIPHY 0-3. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interrupts + - interrupt-names + - interconnects + - interconnect-names + - iommus + - power-domains + - power-domain-names + - vdda-phy-supply + - vdda-pll-supply + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,sa8775p-camcc.h> + #include <dt-bindings/clock/qcom,sa8775p-gcc.h> + #include <dt-bindings/interconnect/qcom,sa8775p-rpmh.h> + #include <dt-bindings/interconnect/qcom,icc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + isp@ac78000 { + compatible = "qcom,sa8775p-camss"; + + reg = <0x0 0xac78000 0x0 0x1000>, + <0x0 0xac7a000 0x0 0x0f00>, + <0x0 0xac7c000 0x0 0x0f00>, + <0x0 0xac84000 0x0 0x0f00>, + <0x0 0xac88000 0x0 0x0f00>, + <0x0 0xac8c000 0x0 0x0f00>, + <0x0 0xac90000 0x0 0x0f00>, + <0x0 0xac94000 0x0 0x0f00>, + <0x0 0xac9c000 0x0 0x2000>, + <0x0 0xac9e000 0x0 0x2000>, + <0x0 0xaca0000 0x0 0x2000>, + <0x0 0xaca2000 0x0 0x2000>, + <0x0 0xacac000 0x0 0x0400>, + <0x0 0xacad000 0x0 0x0400>, + <0x0 0xacae000 0x0 0x0400>, + <0x0 0xac4d000 0x0 0xd000>, + <0x0 0xac5a000 0x0 0xd000>, + <0x0 0xac85000 0x0 0x0d00>, + <0x0 0xac89000 0x0 0x0d00>, + <0x0 0xac8d000 0x0 0x0d00>, + <0x0 0xac91000 0x0 0x0d00>, + <0x0 0xac95000 0x0 0x0d00>; + reg-names = "csid_wrapper", + "csid0", + "csid1", + "csid_lite0", + "csid_lite1", + "csid_lite2", + "csid_lite3", + "csid_lite4", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "tpg0", + "tpg1", + "tpg2", + "vfe0", + "vfe1", + "vfe_lite0", + "vfe_lite1", + "vfe_lite2", + "vfe_lite3", + "vfe_lite4"; + + clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>, + <&camcc CAM_CC_CORE_AHB_CLK>, + <&camcc CAM_CC_CPAS_AHB_CLK>, + <&camcc CAM_CC_CPAS_FAST_AHB_CLK>, + <&camcc CAM_CC_CPAS_IFE_LITE_CLK>, + <&camcc CAM_CC_CPAS_IFE_0_CLK>, + <&camcc CAM_CC_CPAS_IFE_1_CLK>, + <&camcc CAM_CC_CSID_CLK>, + <&camcc CAM_CC_CSIPHY0_CLK>, + <&camcc CAM_CC_CSI0PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY1_CLK>, + <&camcc CAM_CC_CSI1PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY2_CLK>, + <&camcc CAM_CC_CSI2PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY3_CLK>, + <&camcc CAM_CC_CSI3PHYTIMER_CLK>, + <&camcc CAM_CC_CSID_CSIPHY_RX_CLK>, + <&gcc GCC_CAMERA_HF_AXI_CLK>, + <&gcc GCC_CAMERA_SF_AXI_CLK>, + <&camcc CAM_CC_ICP_AHB_CLK>, + <&camcc CAM_CC_IFE_0_CLK>, + <&camcc CAM_CC_IFE_0_FAST_AHB_CLK>, + <&camcc CAM_CC_IFE_1_CLK>, + <&camcc CAM_CC_IFE_1_FAST_AHB_CLK>, + <&camcc CAM_CC_IFE_LITE_CLK>, + <&camcc CAM_CC_IFE_LITE_AHB_CLK>, + <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_LITE_CSID_CLK>; + clock-names = "camnoc_axi", + "core_ahb", + "cpas_ahb", + "cpas_fast_ahb_clk", + "cpas_vfe_lite", + "cpas_vfe0", + "cpas_vfe1", + "csid", + "csiphy0", + "csiphy0_timer", + "csiphy1", + "csiphy1_timer", + "csiphy2", + "csiphy2_timer", + "csiphy3", + "csiphy3_timer", + "csiphy_rx", + "gcc_axi_hf", + "gcc_axi_sf", + "icp_ahb", + "vfe0", + "vfe0_fast_ahb", + "vfe1", + "vfe1_fast_ahb", + "vfe_lite", + "vfe_lite_ahb", + "vfe_lite_cphy_rx", + "vfe_lite_csid"; + + interrupts = <GIC_SPI 565 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 564 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 359 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 759 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 758 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 604 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 448 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 545 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 546 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 547 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 360 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 761 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 760 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 605 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "csid0", + "csid1", + "csid_lite0", + "csid_lite1", + "csid_lite2", + "csid_lite3", + "csid_lite4", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "tpg0", + "tpg1", + "tpg2", + "vfe0", + "vfe1", + "vfe_lite0", + "vfe_lite1", + "vfe_lite2", + "vfe_lite3", + "vfe_lite4"; + + interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY + &config_noc SLAVE_CAMERA_CFG QCOM_ICC_TAG_ACTIVE_ONLY>, + <&mmss_noc MASTER_CAMNOC_HF QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "ahb", + "hf_0"; + + iommus = <&apps_smmu 0x3400 0x20>; + + power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>; + power-domain-names = "top"; + + vdda-phy-supply = <&vreg_l4a_0p88>; + vdda-pll-supply = <&vreg_l1c_1p2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sc7180-venus.yaml b/Documentation/devicetree/bindings/media/qcom,sc7180-venus.yaml new file mode 100644 index 000000000..b21bed314 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sc7180-venus.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sc7180-venus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SC7180 Venus video encode and decode accelerators + +maintainers: + - Stanimir Varbanov <stanimir.varbanov@linaro.org> + +description: | + The Venus IP is a video encode and decode accelerator present + on Qualcomm platforms + +allOf: + - $ref: qcom,venus-common.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - qcom,qcs615-venus + - const: qcom,sc7180-venus + - const: qcom,sc7180-venus + + power-domains: + minItems: 2 + maxItems: 3 + + power-domain-names: + minItems: 2 + items: + - const: venus + - const: vcodec0 + - const: cx + + clocks: + maxItems: 5 + + clock-names: + items: + - const: core + - const: iface + - const: bus + - const: vcodec0_core + - const: vcodec0_bus + + iommus: + maxItems: 1 + + memory-region: + maxItems: 1 + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: video-mem + - const: cpu-cfg + + operating-points-v2: true + opp-table: + type: object + + video-decoder: + type: object + + properties: + compatible: + const: venus-decoder + + required: + - compatible + + deprecated: true + additionalProperties: false + + video-encoder: + type: object + + properties: + compatible: + const: venus-encoder + + required: + - compatible + + deprecated: true + additionalProperties: false + + video-firmware: + type: object + additionalProperties: false + + description: | + Firmware subnode is needed when the platform does not + have TrustZone. + + properties: + iommus: + maxItems: 1 + + required: + - iommus + +required: + - compatible + - power-domain-names + - iommus + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,videocc-sc7180.h> + + venus: video-codec@aa00000 { + compatible = "qcom,sc7180-venus"; + reg = <0x0aa00000 0xff000>; + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&videocc VENUS_GDSC>, + <&videocc VCODEC0_GDSC>; + power-domain-names = "venus", "vcodec0"; + clocks = <&videocc VIDEO_CC_VENUS_CTL_CORE_CLK>, + <&videocc VIDEO_CC_VENUS_AHB_CLK>, + <&videocc VIDEO_CC_VENUS_CTL_AXI_CLK>, + <&videocc VIDEO_CC_VCODEC0_CORE_CLK>, + <&videocc VIDEO_CC_VCODEC0_AXI_CLK>; + clock-names = "core", "iface", "bus", + "vcodec0_core", "vcodec0_bus"; + iommus = <&apps_smmu 0x0c00 0x60>; + memory-region = <&venus_mem>; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sc7280-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sc7280-camss.yaml new file mode 100644 index 000000000..b1c54c5b0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sc7280-camss.yaml @@ -0,0 +1,425 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sc7280-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SC7280 CAMSS ISP + +maintainers: + - Azam Sadiq Pasha Kapatrala Syed <akapatra@quicinc.com> + - Hariram Purushothaman <hariramp@quicinc.com> + +description: + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms. + +properties: + compatible: + const: qcom,sc7280-camss + + reg: + maxItems: 15 + + reg-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid_lite0 + - const: csid_lite1 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: csiphy4 + - const: vfe0 + - const: vfe1 + - const: vfe2 + - const: vfe_lite0 + - const: vfe_lite1 + + clocks: + maxItems: 33 + + clock-names: + items: + - const: camnoc_axi + - const: cpas_ahb + - const: csiphy0 + - const: csiphy0_timer + - const: csiphy1 + - const: csiphy1_timer + - const: csiphy2 + - const: csiphy2_timer + - const: csiphy3 + - const: csiphy3_timer + - const: csiphy4 + - const: csiphy4_timer + - const: gcc_axi_hf + - const: gcc_axi_sf + - const: icp_ahb + - const: vfe0 + - const: vfe0_axi + - const: vfe0_cphy_rx + - const: vfe0_csid + - const: vfe1 + - const: vfe1_axi + - const: vfe1_cphy_rx + - const: vfe1_csid + - const: vfe2 + - const: vfe2_axi + - const: vfe2_cphy_rx + - const: vfe2_csid + - const: vfe_lite0 + - const: vfe_lite0_cphy_rx + - const: vfe_lite0_csid + - const: vfe_lite1 + - const: vfe_lite1_cphy_rx + - const: vfe_lite1_csid + + interrupts: + maxItems: 15 + + interrupt-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid_lite0 + - const: csid_lite1 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: csiphy4 + - const: vfe0 + - const: vfe1 + - const: vfe2 + - const: vfe_lite0 + - const: vfe_lite1 + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: ahb + - const: hf_0 + + iommus: + maxItems: 1 + + power-domains: + items: + - description: IFE0 GDSC - Image Front End, Global Distributed Switch Controller. + - description: IFE1 GDSC - Image Front End, Global Distributed Switch Controller. + - description: IFE2 GDSC - Image Front End, Global Distributed Switch Controller. + - description: Titan GDSC - Titan ISP Block, Global Distributed Switch Controller. + + power-domain-names: + items: + - const: ife0 + - const: ife1 + - const: ife2 + - const: top + + vdda-phy-supply: + description: + 0.88V supply to CSIPHY IP blocks. + + vdda-pll-supply: + description: + 1.2V supply to CSIPHY IP blocks. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSIPHY 0. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSIPHY 1. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSIPHY 2. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + + port@3: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSIPHY 3. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + + port@4: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSIPHY 4. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interrupts + - interrupt-names + - interconnects + - interconnect-names + - iommus + - power-domains + - power-domain-names + - vdda-phy-supply + - vdda-pll-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,camcc-sc7280.h> + #include <dt-bindings/clock/qcom,gcc-sc7280.h> + #include <dt-bindings/interconnect/qcom,sc7280.h> + #include <dt-bindings/interconnect/qcom,icc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + isp@acb3000 { + compatible = "qcom,sc7280-camss"; + + reg = <0x0 0x0acb3000 0x0 0x1000>, + <0x0 0x0acba000 0x0 0x1000>, + <0x0 0x0acc1000 0x0 0x1000>, + <0x0 0x0acc8000 0x0 0x1000>, + <0x0 0x0accf000 0x0 0x1000>, + <0x0 0x0ace0000 0x0 0x2000>, + <0x0 0x0ace2000 0x0 0x2000>, + <0x0 0x0ace4000 0x0 0x2000>, + <0x0 0x0ace6000 0x0 0x2000>, + <0x0 0x0ace8000 0x0 0x2000>, + <0x0 0x0acaf000 0x0 0x4000>, + <0x0 0x0acb6000 0x0 0x4000>, + <0x0 0x0acbd000 0x0 0x4000>, + <0x0 0x0acc4000 0x0 0x4000>, + <0x0 0x0accb000 0x0 0x4000>; + reg-names = "csid0", + "csid1", + "csid2", + "csid_lite0", + "csid_lite1", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "csiphy4", + "vfe0", + "vfe1", + "vfe2", + "vfe_lite0", + "vfe_lite1"; + + clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>, + <&camcc CAM_CC_CPAS_AHB_CLK>, + <&camcc CAM_CC_CSIPHY0_CLK>, + <&camcc CAM_CC_CSI0PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY1_CLK>, + <&camcc CAM_CC_CSI1PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY2_CLK>, + <&camcc CAM_CC_CSI2PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY3_CLK>, + <&camcc CAM_CC_CSI3PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY4_CLK>, + <&camcc CAM_CC_CSI4PHYTIMER_CLK>, + <&gcc GCC_CAMERA_HF_AXI_CLK>, + <&gcc GCC_CAMERA_SF_AXI_CLK>, + <&camcc CAM_CC_ICP_AHB_CLK>, + <&camcc CAM_CC_IFE_0_CLK>, + <&camcc CAM_CC_IFE_0_AXI_CLK>, + <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_0_CSID_CLK>, + <&camcc CAM_CC_IFE_1_CLK>, + <&camcc CAM_CC_IFE_1_AXI_CLK>, + <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_1_CSID_CLK>, + <&camcc CAM_CC_IFE_2_CLK>, + <&camcc CAM_CC_IFE_2_AXI_CLK>, + <&camcc CAM_CC_IFE_2_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_2_CSID_CLK>, + <&camcc CAM_CC_IFE_LITE_0_CLK>, + <&camcc CAM_CC_IFE_LITE_0_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_LITE_0_CSID_CLK>, + <&camcc CAM_CC_IFE_LITE_1_CLK>, + <&camcc CAM_CC_IFE_LITE_1_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_LITE_1_CSID_CLK>; + clock-names = "camnoc_axi", + "cpas_ahb", + "csiphy0", + "csiphy0_timer", + "csiphy1", + "csiphy1_timer", + "csiphy2", + "csiphy2_timer", + "csiphy3", + "csiphy3_timer", + "csiphy4", + "csiphy4_timer", + "gcc_axi_hf", + "gcc_axi_sf", + "icp_ahb", + "vfe0", + "vfe0_axi", + "vfe0_cphy_rx", + "vfe0_csid", + "vfe1", + "vfe1_axi", + "vfe1_cphy_rx", + "vfe1_csid", + "vfe2", + "vfe2_axi", + "vfe2_cphy_rx", + "vfe2_csid", + "vfe_lite0", + "vfe_lite0_cphy_rx", + "vfe_lite0_csid", + "vfe_lite1", + "vfe_lite1_cphy_rx", + "vfe_lite1_csid"; + + interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 640 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 359 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 448 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 122 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 641 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 360 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "csid0", + "csid1", + "csid2", + "csid_lite0", + "csid_lite1", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "csiphy4", + "vfe0", + "vfe1", + "vfe2", + "vfe_lite0", + "vfe_lite1"; + + interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY + &cnoc2 SLAVE_CAMERA_CFG QCOM_ICC_TAG_ACTIVE_ONLY>, + <&mmss_noc MASTER_CAMNOC_HF QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "ahb", + "hf_0"; + + iommus = <&apps_smmu 0x800 0x4e0>; + + power-domains = <&camcc CAM_CC_IFE_0_GDSC>, + <&camcc CAM_CC_IFE_1_GDSC>, + <&camcc CAM_CC_IFE_2_GDSC>, + <&camcc CAM_CC_TITAN_TOP_GDSC>; + power-domain-names = "ife0", + "ife1", + "ife2", + "top"; + + vdda-phy-supply = <&vreg_l10c_0p88>; + vdda-pll-supply = <&vreg_l6b_1p2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sc7280-venus.yaml b/Documentation/devicetree/bindings/media/qcom,sc7280-venus.yaml new file mode 100644 index 000000000..9725fcb76 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sc7280-venus.yaml @@ -0,0 +1,125 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sc7280-venus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SC7280 Venus video encode and decode accelerators + +maintainers: + - Stanimir Varbanov <stanimir.varbanov@linaro.org> + +description: | + The Venus Iris2 IP is a video encode and decode accelerator present + on Qualcomm platforms + +allOf: + - $ref: qcom,venus-common.yaml# + +properties: + compatible: + const: qcom,sc7280-venus + + power-domains: + minItems: 2 + maxItems: 3 + + power-domain-names: + minItems: 2 + items: + - const: venus + - const: vcodec0 + - const: cx + + clocks: + maxItems: 5 + + clock-names: + items: + - const: core + - const: bus + - const: iface + - const: vcodec_core + - const: vcodec_bus + + iommus: + maxItems: 1 + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: cpu-cfg + - const: video-mem + + operating-points-v2: true + opp-table: + type: object + + video-decoder: + type: object + + properties: + compatible: + const: venus-decoder + + required: + - compatible + + deprecated: true + additionalProperties: false + + video-encoder: + type: object + + properties: + compatible: + const: venus-encoder + + required: + - compatible + + deprecated: true + additionalProperties: false + +required: + - compatible + - power-domain-names + - iommus + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,videocc-sc7280.h> + #include <dt-bindings/interconnect/qcom,sc7280.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + venus: video-codec@aa00000 { + compatible = "qcom,sc7280-venus"; + reg = <0x0aa00000 0xd0600>; + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&videocc VIDEO_CC_MVSC_CORE_CLK>, + <&videocc VIDEO_CC_MVSC_CTL_AXI_CLK>, + <&videocc VIDEO_CC_VENUS_AHB_CLK>, + <&videocc VIDEO_CC_MVS0_CORE_CLK>, + <&videocc VIDEO_CC_MVS0_AXI_CLK>; + clock-names = "core", "bus", "iface", + "vcodec_core", "vcodec_bus"; + + power-domains = <&videocc MVSC_GDSC>, + <&videocc MVS0_GDSC>, + <&rpmhpd SC7280_CX>; + power-domain-names = "venus", "vcodec0", "cx"; + + interconnects = <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_VENUS_CFG 0>, + <&mmss_noc MASTER_VIDEO_P0 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "cpu-cfg", "video-mem"; + + iommus = <&apps_smmu 0x2180 0x20>; + + memory-region = <&video_mem>; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sc8280xp-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sc8280xp-camss.yaml new file mode 100644 index 000000000..354130aba --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sc8280xp-camss.yaml @@ -0,0 +1,531 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sc8280xp-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SC8280XP Camera Subsystem (CAMSS) + +maintainers: + - Bryan O'Donoghue <bryan.odonoghue@linaro.org> + +description: | + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms. + +properties: + compatible: + const: qcom,sc8280xp-camss + + clocks: + maxItems: 40 + + clock-names: + items: + - const: camnoc_axi + - const: cpas_ahb + - const: csiphy0 + - const: csiphy0_timer + - const: csiphy1 + - const: csiphy1_timer + - const: csiphy2 + - const: csiphy2_timer + - const: csiphy3 + - const: csiphy3_timer + - const: vfe0_axi + - const: vfe0 + - const: vfe0_cphy_rx + - const: vfe0_csid + - const: vfe1_axi + - const: vfe1 + - const: vfe1_cphy_rx + - const: vfe1_csid + - const: vfe2_axi + - const: vfe2 + - const: vfe2_cphy_rx + - const: vfe2_csid + - const: vfe3_axi + - const: vfe3 + - const: vfe3_cphy_rx + - const: vfe3_csid + - const: vfe_lite0 + - const: vfe_lite0_cphy_rx + - const: vfe_lite0_csid + - const: vfe_lite1 + - const: vfe_lite1_cphy_rx + - const: vfe_lite1_csid + - const: vfe_lite2 + - const: vfe_lite2_cphy_rx + - const: vfe_lite2_csid + - const: vfe_lite3 + - const: vfe_lite3_cphy_rx + - const: vfe_lite3_csid + - const: gcc_axi_hf + - const: gcc_axi_sf + + interrupts: + maxItems: 20 + + interrupt-names: + items: + - const: csid1_lite + - const: vfe_lite1 + - const: csiphy3 + - const: csid0 + - const: vfe0 + - const: csid1 + - const: vfe1 + - const: csid0_lite + - const: vfe_lite0 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csid2 + - const: vfe2 + - const: csid3_lite + - const: csid2_lite + - const: vfe_lite3 + - const: vfe_lite2 + - const: csid3 + - const: vfe3 + + iommus: + maxItems: 16 + + interconnects: + maxItems: 4 + + interconnect-names: + items: + - const: cam_ahb + - const: cam_hf_mnoc + - const: cam_sf_mnoc + - const: cam_sf_icp_mnoc + + power-domains: + items: + - description: IFE0 GDSC - Image Front End, Global Distributed Switch Controller. + - description: IFE1 GDSC - Image Front End, Global Distributed Switch Controller. + - description: IFE2 GDSC - Image Front End, Global Distributed Switch Controller. + - description: IFE3 GDSC - Image Front End, Global Distributed Switch Controller. + - description: Titan Top GDSC - Titan ISP Block, Global Distributed Switch Controller. + + power-domain-names: + items: + - const: ife0 + - const: ife1 + - const: ife2 + - const: ife3 + - const: top + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data from CSIPHY0. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data from CSIPHY1. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data from CSIPHY2. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@3: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data from CSIPHY3. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + reg: + maxItems: 20 + + reg-names: + items: + - const: csiphy2 + - const: csiphy3 + - const: csiphy0 + - const: csiphy1 + - const: vfe0 + - const: csid0 + - const: vfe1 + - const: csid1 + - const: vfe2 + - const: csid2 + - const: vfe_lite0 + - const: csid0_lite + - const: vfe_lite1 + - const: csid1_lite + - const: vfe_lite2 + - const: csid2_lite + - const: vfe_lite3 + - const: csid3_lite + - const: vfe3 + - const: csid3 + + vdda-phy-supply: + description: + 0.88V supply to CSIPHY IP blocks. + + vdda-pll-supply: + description: + 1.2V supply to CSIPHY IP blocks. + +required: + - clock-names + - clocks + - compatible + - interconnects + - interconnect-names + - interrupts + - interrupt-names + - iommus + - power-domains + - power-domain-names + - reg + - reg-names + - vdda-phy-supply + - vdda-pll-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-sc8280xp.h> + #include <dt-bindings/clock/qcom,sc8280xp-camcc.h> + #include <dt-bindings/interconnect/qcom,sc8280xp.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + camss: camss@ac5a000 { + compatible = "qcom,sc8280xp-camss"; + + reg = <0 0x0ac5a000 0 0x2000>, + <0 0x0ac5c000 0 0x2000>, + <0 0x0ac65000 0 0x2000>, + <0 0x0ac67000 0 0x2000>, + <0 0x0acaf000 0 0x4000>, + <0 0x0acb3000 0 0x1000>, + <0 0x0acb6000 0 0x4000>, + <0 0x0acba000 0 0x1000>, + <0 0x0acbd000 0 0x4000>, + <0 0x0acc1000 0 0x1000>, + <0 0x0acc4000 0 0x4000>, + <0 0x0acc8000 0 0x1000>, + <0 0x0accb000 0 0x4000>, + <0 0x0accf000 0 0x1000>, + <0 0x0acd2000 0 0x4000>, + <0 0x0acd6000 0 0x1000>, + <0 0x0acd9000 0 0x4000>, + <0 0x0acdd000 0 0x1000>, + <0 0x0ace0000 0 0x4000>, + <0 0x0ace4000 0 0x1000>; + + reg-names = "csiphy2", + "csiphy3", + "csiphy0", + "csiphy1", + "vfe0", + "csid0", + "vfe1", + "csid1", + "vfe2", + "csid2", + "vfe_lite0", + "csid0_lite", + "vfe_lite1", + "csid1_lite", + "vfe_lite2", + "csid2_lite", + "vfe_lite3", + "csid3_lite", + "vfe3", + "csid3"; + + vdda-phy-supply = <&vreg_l6d>; + vdda-pll-supply = <&vreg_l4d>; + + interrupts = <GIC_SPI 359 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 360 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 448 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 640 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 641 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 758 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 759 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 760 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 761 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 762 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 764 IRQ_TYPE_EDGE_RISING>; + + interrupt-names = "csid1_lite", + "vfe_lite1", + "csiphy3", + "csid0", + "vfe0", + "csid1", + "vfe1", + "csid0_lite", + "vfe_lite0", + "csiphy0", + "csiphy1", + "csiphy2", + "csid2", + "vfe2", + "csid3_lite", + "csid2_lite", + "vfe_lite3", + "vfe_lite2", + "csid3", + "vfe3"; + + power-domains = <&camcc IFE_0_GDSC>, + <&camcc IFE_1_GDSC>, + <&camcc IFE_2_GDSC>, + <&camcc IFE_3_GDSC>, + <&camcc TITAN_TOP_GDSC>; + + power-domain-names = "ife0", + "ife1", + "ife2", + "ife3", + "top"; + + clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>, + <&camcc CAMCC_CPAS_AHB_CLK>, + <&camcc CAMCC_CSIPHY0_CLK>, + <&camcc CAMCC_CSI0PHYTIMER_CLK>, + <&camcc CAMCC_CSIPHY1_CLK>, + <&camcc CAMCC_CSI1PHYTIMER_CLK>, + <&camcc CAMCC_CSIPHY2_CLK>, + <&camcc CAMCC_CSI2PHYTIMER_CLK>, + <&camcc CAMCC_CSIPHY3_CLK>, + <&camcc CAMCC_CSI3PHYTIMER_CLK>, + <&camcc CAMCC_IFE_0_AXI_CLK>, + <&camcc CAMCC_IFE_0_CLK>, + <&camcc CAMCC_IFE_0_CPHY_RX_CLK>, + <&camcc CAMCC_IFE_0_CSID_CLK>, + <&camcc CAMCC_IFE_1_AXI_CLK>, + <&camcc CAMCC_IFE_1_CLK>, + <&camcc CAMCC_IFE_1_CPHY_RX_CLK>, + <&camcc CAMCC_IFE_1_CSID_CLK>, + <&camcc CAMCC_IFE_2_AXI_CLK>, + <&camcc CAMCC_IFE_2_CLK>, + <&camcc CAMCC_IFE_2_CPHY_RX_CLK>, + <&camcc CAMCC_IFE_2_CSID_CLK>, + <&camcc CAMCC_IFE_3_AXI_CLK>, + <&camcc CAMCC_IFE_3_CLK>, + <&camcc CAMCC_IFE_3_CPHY_RX_CLK>, + <&camcc CAMCC_IFE_3_CSID_CLK>, + <&camcc CAMCC_IFE_LITE_0_CLK>, + <&camcc CAMCC_IFE_LITE_0_CPHY_RX_CLK>, + <&camcc CAMCC_IFE_LITE_0_CSID_CLK>, + <&camcc CAMCC_IFE_LITE_1_CLK>, + <&camcc CAMCC_IFE_LITE_1_CPHY_RX_CLK>, + <&camcc CAMCC_IFE_LITE_1_CSID_CLK>, + <&camcc CAMCC_IFE_LITE_2_CLK>, + <&camcc CAMCC_IFE_LITE_2_CPHY_RX_CLK>, + <&camcc CAMCC_IFE_LITE_2_CSID_CLK>, + <&camcc CAMCC_IFE_LITE_3_CLK>, + <&camcc CAMCC_IFE_LITE_3_CPHY_RX_CLK>, + <&camcc CAMCC_IFE_LITE_3_CSID_CLK>, + <&gcc GCC_CAMERA_HF_AXI_CLK>, + <&gcc GCC_CAMERA_SF_AXI_CLK>; + + clock-names = "camnoc_axi", + "cpas_ahb", + "csiphy0", + "csiphy0_timer", + "csiphy1", + "csiphy1_timer", + "csiphy2", + "csiphy2_timer", + "csiphy3", + "csiphy3_timer", + "vfe0_axi", + "vfe0", + "vfe0_cphy_rx", + "vfe0_csid", + "vfe1_axi", + "vfe1", + "vfe1_cphy_rx", + "vfe1_csid", + "vfe2_axi", + "vfe2", + "vfe2_cphy_rx", + "vfe2_csid", + "vfe3_axi", + "vfe3", + "vfe3_cphy_rx", + "vfe3_csid", + "vfe_lite0", + "vfe_lite0_cphy_rx", + "vfe_lite0_csid", + "vfe_lite1", + "vfe_lite1_cphy_rx", + "vfe_lite1_csid", + "vfe_lite2", + "vfe_lite2_cphy_rx", + "vfe_lite2_csid", + "vfe_lite3", + "vfe_lite3_cphy_rx", + "vfe_lite3_csid", + "gcc_axi_hf", + "gcc_axi_sf"; + + iommus = <&apps_smmu 0x2000 0x4e0>, + <&apps_smmu 0x2020 0x4e0>, + <&apps_smmu 0x2040 0x4e0>, + <&apps_smmu 0x2060 0x4e0>, + <&apps_smmu 0x2080 0x4e0>, + <&apps_smmu 0x20e0 0x4e0>, + <&apps_smmu 0x20c0 0x4e0>, + <&apps_smmu 0x20a0 0x4e0>, + <&apps_smmu 0x2400 0x4e0>, + <&apps_smmu 0x2420 0x4e0>, + <&apps_smmu 0x2440 0x4e0>, + <&apps_smmu 0x2460 0x4e0>, + <&apps_smmu 0x2480 0x4e0>, + <&apps_smmu 0x24e0 0x4e0>, + <&apps_smmu 0x24c0 0x4e0>, + <&apps_smmu 0x24a0 0x4e0>; + + interconnects = <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_CAMERA_CFG 0>, + <&mmss_noc MASTER_CAMNOC_HF 0 &mc_virt SLAVE_EBI1 0>, + <&mmss_noc MASTER_CAMNOC_SF 0 &mc_virt SLAVE_EBI1 0>, + <&mmss_noc MASTER_CAMNOC_ICP 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "cam_ahb", + "cam_hf_mnoc", + "cam_sf_mnoc", + "cam_sf_icp_mnoc"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + csiphy_ep0: endpoint@0 { + reg = <0>; + clock-lanes = <7>; + data-lanes = <0 1>; + remote-endpoint = <&sensor_ep>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sdm660-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sdm660-camss.yaml new file mode 100644 index 000000000..6e6ad8390 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sdm660-camss.yaml @@ -0,0 +1,404 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sdm660-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm CAMSS ISP + +maintainers: + - Robert Foss <robert.foss@linaro.org> + - AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> + +description: | + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms + +properties: + compatible: + const: qcom,sdm660-camss + + clocks: + minItems: 42 + maxItems: 42 + + clock-names: + items: + - const: ahb + - const: cphy_csid0 + - const: cphy_csid1 + - const: cphy_csid2 + - const: cphy_csid3 + - const: csi0_ahb + - const: csi0 + - const: csi0_phy + - const: csi0_pix + - const: csi0_rdi + - const: csi1_ahb + - const: csi1 + - const: csi1_phy + - const: csi1_pix + - const: csi1_rdi + - const: csi2_ahb + - const: csi2 + - const: csi2_phy + - const: csi2_pix + - const: csi2_rdi + - const: csi3_ahb + - const: csi3 + - const: csi3_phy + - const: csi3_pix + - const: csi3_rdi + - const: csiphy0_timer + - const: csiphy1_timer + - const: csiphy2_timer + - const: csiphy_ahb2crif + - const: csi_vfe0 + - const: csi_vfe1 + - const: ispif_ahb + - const: throttle_axi + - const: top_ahb + - const: vfe0_ahb + - const: vfe0 + - const: vfe0_stream + - const: vfe1_ahb + - const: vfe1 + - const: vfe1_stream + - const: vfe_ahb + - const: vfe_axi + + interrupts: + minItems: 10 + maxItems: 10 + + interrupt-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid3 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: ispif + - const: vfe0 + - const: vfe1 + + interconnects: + maxItems: 1 + + interconnect-names: + items: + - const: vfe-mem + + iommus: + maxItems: 4 + + power-domains: + items: + - description: VFE0 GDSC - Video Front End, Global Distributed Switch Controller. + - description: VFE1 GDSC - Video Front End, Global Distributed Switch Controller. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + port@3: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + reg: + minItems: 14 + maxItems: 14 + + reg-names: + items: + - const: csi_clk_mux + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid3 + - const: csiphy0 + - const: csiphy0_clk_mux + - const: csiphy1 + - const: csiphy1_clk_mux + - const: csiphy2 + - const: csiphy2_clk_mux + - const: ispif + - const: vfe0 + - const: vfe1 + + vdda-supply: + description: + Definition of the regulator used as analog power supply. + +required: + - clock-names + - clocks + - compatible + - interrupt-names + - interrupts + - iommus + - power-domains + - reg + - reg-names + - vdda-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-sdm660.h> + #include <dt-bindings/clock/qcom,mmcc-sdm660.h> + + camss: camss@ca00020 { + compatible = "qcom,sdm660-camss"; + + clocks = <&mmcc CAMSS_AHB_CLK>, + <&mmcc CAMSS_CPHY_CSID0_CLK>, + <&mmcc CAMSS_CPHY_CSID1_CLK>, + <&mmcc CAMSS_CPHY_CSID2_CLK>, + <&mmcc CAMSS_CPHY_CSID3_CLK>, + <&mmcc CAMSS_CSI0_AHB_CLK>, + <&mmcc CAMSS_CSI0_CLK>, + <&mmcc CAMSS_CPHY_CSID0_CLK>, + <&mmcc CAMSS_CSI0PIX_CLK>, + <&mmcc CAMSS_CSI0RDI_CLK>, + <&mmcc CAMSS_CSI1_AHB_CLK>, + <&mmcc CAMSS_CSI1_CLK>, + <&mmcc CAMSS_CPHY_CSID1_CLK>, + <&mmcc CAMSS_CSI1PIX_CLK>, + <&mmcc CAMSS_CSI1RDI_CLK>, + <&mmcc CAMSS_CSI2_AHB_CLK>, + <&mmcc CAMSS_CSI2_CLK>, + <&mmcc CAMSS_CPHY_CSID2_CLK>, + <&mmcc CAMSS_CSI2PIX_CLK>, + <&mmcc CAMSS_CSI2RDI_CLK>, + <&mmcc CAMSS_CSI3_AHB_CLK>, + <&mmcc CAMSS_CSI3_CLK>, + <&mmcc CAMSS_CPHY_CSID3_CLK>, + <&mmcc CAMSS_CSI3PIX_CLK>, + <&mmcc CAMSS_CSI3RDI_CLK>, + <&mmcc CAMSS_CSI0PHYTIMER_CLK>, + <&mmcc CAMSS_CSI1PHYTIMER_CLK>, + <&mmcc CAMSS_CSI2PHYTIMER_CLK>, + <&mmcc CSIPHY_AHB2CRIF_CLK>, + <&mmcc CAMSS_CSI_VFE0_CLK>, + <&mmcc CAMSS_CSI_VFE1_CLK>, + <&mmcc CAMSS_ISPIF_AHB_CLK>, + <&mmcc THROTTLE_CAMSS_AXI_CLK>, + <&mmcc CAMSS_TOP_AHB_CLK>, + <&mmcc CAMSS_VFE0_AHB_CLK>, + <&mmcc CAMSS_VFE0_CLK>, + <&mmcc CAMSS_VFE0_STREAM_CLK>, + <&mmcc CAMSS_VFE1_AHB_CLK>, + <&mmcc CAMSS_VFE1_CLK>, + <&mmcc CAMSS_VFE1_STREAM_CLK>, + <&mmcc CAMSS_VFE_VBIF_AHB_CLK>, + <&mmcc CAMSS_VFE_VBIF_AXI_CLK>; + + clock-names = "ahb", + "cphy_csid0", + "cphy_csid1", + "cphy_csid2", + "cphy_csid3", + "csi0_ahb", + "csi0", + "csi0_phy", + "csi0_pix", + "csi0_rdi", + "csi1_ahb", + "csi1", + "csi1_phy", + "csi1_pix", + "csi1_rdi", + "csi2_ahb", + "csi2", + "csi2_phy", + "csi2_pix", + "csi2_rdi", + "csi3_ahb", + "csi3", + "csi3_phy", + "csi3_pix", + "csi3_rdi", + "csiphy0_timer", + "csiphy1_timer", + "csiphy2_timer", + "csiphy_ahb2crif", + "csi_vfe0", + "csi_vfe1", + "ispif_ahb", + "throttle_axi", + "top_ahb", + "vfe0_ahb", + "vfe0", + "vfe0_stream", + "vfe1_ahb", + "vfe1", + "vfe1_stream", + "vfe_ahb", + "vfe_axi"; + + interrupts = <GIC_SPI 296 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 297 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 298 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 299 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 80 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 309 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 314 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 315 IRQ_TYPE_EDGE_RISING>; + + interrupt-names = "csid0", + "csid1", + "csid2", + "csid3", + "csiphy0", + "csiphy1", + "csiphy2", + "ispif", + "vfe0", + "vfe1"; + + iommus = <&mmss_smmu 0xc00>, + <&mmss_smmu 0xc01>, + <&mmss_smmu 0xc02>, + <&mmss_smmu 0xc03>; + + power-domains = <&mmcc CAMSS_VFE0_GDSC>, + <&mmcc CAMSS_VFE1_GDSC>; + + reg = <0x0ca00020 0x10>, + <0x0ca30000 0x100>, + <0x0ca30400 0x100>, + <0x0ca30800 0x100>, + <0x0ca30c00 0x100>, + <0x0c824000 0x1000>, + <0x0ca00120 0x4>, + <0x0c825000 0x1000>, + <0x0ca00124 0x4>, + <0x0c826000 0x1000>, + <0x0ca00128 0x4>, + <0x0ca31000 0x500>, + <0x0ca10000 0x1000>, + <0x0ca14000 0x1000>; + + reg-names = "csi_clk_mux", + "csid0", + "csid1", + "csid2", + "csid3", + "csiphy0", + "csiphy0_clk_mux", + "csiphy1", + "csiphy1_clk_mux", + "csiphy2", + "csiphy2_clk_mux", + "ispif", + "vfe0", + "vfe1"; + + vdda-supply = <®_2v8>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sdm660-venus.yaml b/Documentation/devicetree/bindings/media/qcom,sdm660-venus.yaml new file mode 100644 index 000000000..a51835b22 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sdm660-venus.yaml @@ -0,0 +1,159 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sdm660-venus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SDM660 Venus video encode and decode accelerators + +maintainers: + - Stanimir Varbanov <stanimir.varbanov@linaro.org> + - AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> + +description: | + The Venus IP is a video encode and decode accelerator present + on Qualcomm platforms + +allOf: + - $ref: qcom,venus-common.yaml# + +properties: + compatible: + const: qcom,sdm660-venus + + clocks: + maxItems: 4 + + clock-names: + items: + - const: core + - const: iface + - const: bus + - const: bus_throttle + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: cpu-cfg + - const: video-mem + + iommus: + maxItems: 20 + + power-domains: + maxItems: 1 + + video-decoder: + type: object + + properties: + compatible: + const: venus-decoder + + clocks: + maxItems: 1 + + clock-names: + items: + - const: vcodec0_core + + power-domains: + maxItems: 1 + + required: + - compatible + - clocks + - clock-names + - power-domains + + additionalProperties: false + + video-encoder: + type: object + + properties: + compatible: + const: venus-encoder + + clocks: + maxItems: 1 + + clock-names: + items: + - const: vcodec0_core + + power-domains: + maxItems: 1 + + required: + - compatible + - clocks + - clock-names + - power-domains + + additionalProperties: false + +required: + - compatible + - iommus + - video-decoder + - video-encoder + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,mmcc-sdm660.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + video-codec@cc00000 { + compatible = "qcom,sdm660-venus"; + reg = <0x0cc00000 0xff000>; + clocks = <&mmcc VIDEO_CORE_CLK>, + <&mmcc VIDEO_AHB_CLK>, + <&mmcc VIDEO_AXI_CLK>, + <&mmcc THROTTLE_VIDEO_AXI_CLK>; + clock-names = "core", "iface", "bus", "bus_throttle"; + interconnects = <&gnoc 0 &mnoc 13>, + <&mnoc 4 &bimc 5>; + interconnect-names = "cpu-cfg", "video-mem"; + interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&mmss_smmu 0x400>, + <&mmss_smmu 0x401>, + <&mmss_smmu 0x40a>, + <&mmss_smmu 0x407>, + <&mmss_smmu 0x40e>, + <&mmss_smmu 0x40f>, + <&mmss_smmu 0x408>, + <&mmss_smmu 0x409>, + <&mmss_smmu 0x40b>, + <&mmss_smmu 0x40c>, + <&mmss_smmu 0x40d>, + <&mmss_smmu 0x410>, + <&mmss_smmu 0x421>, + <&mmss_smmu 0x428>, + <&mmss_smmu 0x429>, + <&mmss_smmu 0x42b>, + <&mmss_smmu 0x42c>, + <&mmss_smmu 0x42d>, + <&mmss_smmu 0x411>, + <&mmss_smmu 0x431>; + memory-region = <&venus_region>; + power-domains = <&mmcc VENUS_GDSC>; + + video-decoder { + compatible = "venus-decoder"; + clocks = <&mmcc VIDEO_SUBCORE0_CLK>; + clock-names = "vcodec0_core"; + power-domains = <&mmcc VENUS_CORE0_GDSC>; + }; + + video-encoder { + compatible = "venus-encoder"; + clocks = <&mmcc VIDEO_SUBCORE0_CLK>; + clock-names = "vcodec0_core"; + power-domains = <&mmcc VENUS_CORE0_GDSC>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml new file mode 100644 index 000000000..084b65740 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml @@ -0,0 +1,315 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sdm670-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SDM670 Camera Subsystem (CAMSS) + +maintainers: + - Richard Acayan <mailingradian@gmail.com> + +description: + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms. + +properties: + compatible: + const: qcom,sdm670-camss + + reg: + maxItems: 9 + + reg-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: vfe0 + - const: vfe1 + - const: vfe_lite + + interrupts: + maxItems: 9 + + interrupt-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: vfe0 + - const: vfe1 + - const: vfe_lite + + clocks: + maxItems: 22 + + clock-names: + items: + - const: camnoc_axi + - const: cpas_ahb + - const: csi0 + - const: csi1 + - const: csi2 + - const: csiphy0 + - const: csiphy0_timer + - const: csiphy1 + - const: csiphy1_timer + - const: csiphy2 + - const: csiphy2_timer + - const: gcc_camera_ahb + - const: gcc_camera_axi + - const: soc_ahb + - const: vfe0 + - const: vfe0_axi + - const: vfe0_cphy_rx + - const: vfe1 + - const: vfe1_axi + - const: vfe1_cphy_rx + - const: vfe_lite + - const: vfe_lite_cphy_rx + + iommus: + maxItems: 4 + + power-domains: + items: + - description: IFE0 GDSC - Image Front End, Global Distributed Switch Controller. + - description: IFE1 GDSC - Image Front End, Global Distributed Switch Controller. + - description: Titan Top GDSC - Titan ISP Block, Global Distributed Switch Controller. + + power-domain-names: + items: + - const: ife0 + - const: ife1 + - const: top + + vdda-phy-supply: + description: + 0.88V supply to CSIPHY IP blocks. + + vdda-pll-supply: + description: + 1.2V supply to CSIPHY IP blocks. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data from CSIPHY0. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data from CSIPHY1. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data from CSIPHY2. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-names + - clocks + - clock-names + - iommus + - power-domains + - power-domain-names + - vdda-phy-supply + - vdda-pll-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,camcc-sdm845.h> + #include <dt-bindings/clock/qcom,gcc-sdm845.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + isp@acb3000 { + compatible = "qcom,sdm670-camss"; + + reg = <0 0x0acb3000 0 0x1000>, + <0 0x0acba000 0 0x1000>, + <0 0x0acc8000 0 0x1000>, + <0 0x0ac65000 0 0x1000>, + <0 0x0ac66000 0 0x1000>, + <0 0x0ac67000 0 0x1000>, + <0 0x0acaf000 0 0x4000>, + <0 0x0acb6000 0 0x4000>, + <0 0x0acc4000 0 0x4000>; + reg-names = "csid0", + "csid1", + "csid2", + "csiphy0", + "csiphy1", + "csiphy2", + "vfe0", + "vfe1", + "vfe_lite"; + + interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "csid0", + "csid1", + "csid2", + "csiphy0", + "csiphy1", + "csiphy2", + "vfe0", + "vfe1", + "vfe_lite"; + + clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>, + <&camcc CAM_CC_CPAS_AHB_CLK>, + <&camcc CAM_CC_IFE_0_CSID_CLK>, + <&camcc CAM_CC_IFE_1_CSID_CLK>, + <&camcc CAM_CC_IFE_LITE_CSID_CLK>, + <&camcc CAM_CC_CSIPHY0_CLK>, + <&camcc CAM_CC_CSI0PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY1_CLK>, + <&camcc CAM_CC_CSI1PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY2_CLK>, + <&camcc CAM_CC_CSI2PHYTIMER_CLK>, + <&gcc GCC_CAMERA_AHB_CLK>, + <&gcc GCC_CAMERA_AXI_CLK>, + <&camcc CAM_CC_SOC_AHB_CLK>, + <&camcc CAM_CC_IFE_0_CLK>, + <&camcc CAM_CC_IFE_0_AXI_CLK>, + <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_1_CLK>, + <&camcc CAM_CC_IFE_1_AXI_CLK>, + <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_LITE_CLK>, + <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>; + clock-names = "camnoc_axi", + "cpas_ahb", + "csi0", + "csi1", + "csi2", + "csiphy0", + "csiphy0_timer", + "csiphy1", + "csiphy1_timer", + "csiphy2", + "csiphy2_timer", + "gcc_camera_ahb", + "gcc_camera_axi", + "soc_ahb", + "vfe0", + "vfe0_axi", + "vfe0_cphy_rx", + "vfe1", + "vfe1_axi", + "vfe1_cphy_rx", + "vfe_lite", + "vfe_lite_cphy_rx"; + + iommus = <&apps_smmu 0x808 0x0>, + <&apps_smmu 0x810 0x8>, + <&apps_smmu 0xc08 0x0>, + <&apps_smmu 0xc10 0x8>; + + power-domains = <&camcc IFE_0_GDSC>, + <&camcc IFE_1_GDSC>, + <&camcc TITAN_TOP_GDSC>; + power-domain-names = "ife0", + "ife1", + "top"; + + vdda-phy-supply = <&vreg_l1a_1p225>; + vdda-pll-supply = <&vreg_l8a_1p8>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + csiphy_ep0: endpoint { + clock-lanes = <7>; + data-lanes = <0 1 2 3>; + remote-endpoint = <&front_sensor_ep>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sdm845-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sdm845-camss.yaml new file mode 100644 index 000000000..be09cf3a3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sdm845-camss.yaml @@ -0,0 +1,379 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sdm845-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm CAMSS ISP + +maintainers: + - Robert Foss <robert.foss@linaro.org> + +description: | + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms + +properties: + compatible: + const: qcom,sdm845-camss + + clocks: + minItems: 36 + maxItems: 36 + + clock-names: + items: + - const: camnoc_axi + - const: cpas_ahb + - const: cphy_rx_src + - const: csi0 + - const: csi0_src + - const: csi1 + - const: csi1_src + - const: csi2 + - const: csi2_src + - const: csiphy0 + - const: csiphy0_timer + - const: csiphy0_timer_src + - const: csiphy1 + - const: csiphy1_timer + - const: csiphy1_timer_src + - const: csiphy2 + - const: csiphy2_timer + - const: csiphy2_timer_src + - const: csiphy3 + - const: csiphy3_timer + - const: csiphy3_timer_src + - const: gcc_camera_ahb + - const: gcc_camera_axi + - const: slow_ahb_src + - const: soc_ahb + - const: vfe0_axi + - const: vfe0 + - const: vfe0_cphy_rx + - const: vfe0_src + - const: vfe1_axi + - const: vfe1 + - const: vfe1_cphy_rx + - const: vfe1_src + - const: vfe_lite + - const: vfe_lite_cphy_rx + - const: vfe_lite_src + + interrupts: + minItems: 10 + maxItems: 10 + + interrupt-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: vfe0 + - const: vfe1 + - const: vfe_lite + + iommus: + maxItems: 4 + + power-domains: + items: + - description: IFE0 GDSC - Image Front End, Global Distributed Switch Controller. + - description: IFE1 GDSC - Image Front End, Global Distributed Switch Controller. + - description: Titan GDSC - Titan ISP Block, Global Distributed Switch Controller. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + port@3: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + reg: + minItems: 10 + maxItems: 10 + + reg-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: vfe0 + - const: vfe1 + - const: vfe_lite + + vdda-phy-supply: + description: + 0.88V supply to CSIPHY IP blocks. + + vdda-pll-supply: + description: + 1.2V supply to CSIPHY IP blocks. + +required: + - clock-names + - clocks + - compatible + - interrupt-names + - interrupts + - iommus + - power-domains + - reg + - reg-names + - vdda-phy-supply + - vdda-pll-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,camcc-sdm845.h> + #include <dt-bindings/clock/qcom,gcc-sdm845.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + camss: camss@acb3000 { + compatible = "qcom,sdm845-camss"; + + clocks = <&clock_camcc CAM_CC_CAMNOC_AXI_CLK>, + <&clock_camcc CAM_CC_CPAS_AHB_CLK>, + <&clock_camcc CAM_CC_CPHY_RX_CLK_SRC>, + <&clock_camcc CAM_CC_IFE_0_CSID_CLK>, + <&clock_camcc CAM_CC_IFE_0_CSID_CLK_SRC>, + <&clock_camcc CAM_CC_IFE_1_CSID_CLK>, + <&clock_camcc CAM_CC_IFE_1_CSID_CLK_SRC>, + <&clock_camcc CAM_CC_IFE_LITE_CSID_CLK>, + <&clock_camcc CAM_CC_IFE_LITE_CSID_CLK_SRC>, + <&clock_camcc CAM_CC_CSIPHY0_CLK>, + <&clock_camcc CAM_CC_CSI0PHYTIMER_CLK>, + <&clock_camcc CAM_CC_CSI0PHYTIMER_CLK_SRC>, + <&clock_camcc CAM_CC_CSIPHY1_CLK>, + <&clock_camcc CAM_CC_CSI1PHYTIMER_CLK>, + <&clock_camcc CAM_CC_CSI1PHYTIMER_CLK_SRC>, + <&clock_camcc CAM_CC_CSIPHY2_CLK>, + <&clock_camcc CAM_CC_CSI2PHYTIMER_CLK>, + <&clock_camcc CAM_CC_CSI2PHYTIMER_CLK_SRC>, + <&clock_camcc CAM_CC_CSIPHY3_CLK>, + <&clock_camcc CAM_CC_CSI3PHYTIMER_CLK>, + <&clock_camcc CAM_CC_CSI3PHYTIMER_CLK_SRC>, + <&gcc GCC_CAMERA_AHB_CLK>, + <&gcc GCC_CAMERA_AXI_CLK>, + <&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>, + <&clock_camcc CAM_CC_SOC_AHB_CLK>, + <&clock_camcc CAM_CC_IFE_0_AXI_CLK>, + <&clock_camcc CAM_CC_IFE_0_CLK>, + <&clock_camcc CAM_CC_IFE_0_CPHY_RX_CLK>, + <&clock_camcc CAM_CC_IFE_0_CLK_SRC>, + <&clock_camcc CAM_CC_IFE_1_AXI_CLK>, + <&clock_camcc CAM_CC_IFE_1_CLK>, + <&clock_camcc CAM_CC_IFE_1_CPHY_RX_CLK>, + <&clock_camcc CAM_CC_IFE_1_CLK_SRC>, + <&clock_camcc CAM_CC_IFE_LITE_CLK>, + <&clock_camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>, + <&clock_camcc CAM_CC_IFE_LITE_CLK_SRC>; + + clock-names = "camnoc_axi", + "cpas_ahb", + "cphy_rx_src", + "csi0", + "csi0_src", + "csi1", + "csi1_src", + "csi2", + "csi2_src", + "csiphy0", + "csiphy0_timer", + "csiphy0_timer_src", + "csiphy1", + "csiphy1_timer", + "csiphy1_timer_src", + "csiphy2", + "csiphy2_timer", + "csiphy2_timer_src", + "csiphy3", + "csiphy3_timer", + "csiphy3_timer_src", + "gcc_camera_ahb", + "gcc_camera_axi", + "slow_ahb_src", + "soc_ahb", + "vfe0_axi", + "vfe0", + "vfe0_cphy_rx", + "vfe0_src", + "vfe1_axi", + "vfe1", + "vfe1_cphy_rx", + "vfe1_src", + "vfe_lite", + "vfe_lite_cphy_rx", + "vfe_lite_src"; + + interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 448 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>; + + interrupt-names = "csid0", + "csid1", + "csid2", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "vfe0", + "vfe1", + "vfe_lite"; + + iommus = <&apps_smmu 0x0808 0x0>, + <&apps_smmu 0x0810 0x8>, + <&apps_smmu 0x0c08 0x0>, + <&apps_smmu 0x0c10 0x8>; + + power-domains = <&clock_camcc IFE_0_GDSC>, + <&clock_camcc IFE_1_GDSC>, + <&clock_camcc TITAN_TOP_GDSC>; + + reg = <0 0xacb3000 0 0x1000>, + <0 0xacba000 0 0x1000>, + <0 0xacc8000 0 0x1000>, + <0 0xac65000 0 0x1000>, + <0 0xac66000 0 0x1000>, + <0 0xac67000 0 0x1000>, + <0 0xac68000 0 0x1000>, + <0 0xacaf000 0 0x4000>, + <0 0xacb6000 0 0x4000>, + <0 0xacc4000 0 0x4000>; + + reg-names = "csid0", + "csid1", + "csid2", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "vfe0", + "vfe1", + "vfe_lite"; + + vdda-phy-supply = <&vreg_l1a_0p875>; + vdda-pll-supply = <&vreg_l26a_1p2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sdm845-venus-v2.yaml b/Documentation/devicetree/bindings/media/qcom,sdm845-venus-v2.yaml new file mode 100644 index 000000000..c839cb1eb --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sdm845-venus-v2.yaml @@ -0,0 +1,122 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sdm845-venus-v2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SDM845 Venus v2 video encode and decode accelerators + +maintainers: + - Stanimir Varbanov <stanimir.varbanov@linaro.org> + +description: | + The Venus IP is a video encode and decode accelerator present + on Qualcomm platforms + +allOf: + - $ref: qcom,venus-common.yaml# + +properties: + compatible: + const: qcom,sdm845-venus-v2 + + power-domains: + minItems: 3 + maxItems: 4 + + power-domain-names: + minItems: 3 + items: + - const: venus + - const: vcodec0 + - const: vcodec1 + - const: cx + + clocks: + maxItems: 7 + + clock-names: + items: + - const: core + - const: iface + - const: bus + - const: vcodec0_core + - const: vcodec0_bus + - const: vcodec1_core + - const: vcodec1_bus + + iommus: + maxItems: 2 + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: video-mem + - const: cpu-cfg + + operating-points-v2: true + opp-table: + type: object + + video-core0: + type: object + + properties: + compatible: + const: venus-decoder + + required: + - compatible + + deprecated: true + additionalProperties: false + + video-core1: + type: object + + properties: + compatible: + const: venus-encoder + + required: + - compatible + + deprecated: true + additionalProperties: false + +required: + - compatible + - power-domain-names + - iommus + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,videocc-sdm845.h> + + video-codec@aa00000 { + compatible = "qcom,sdm845-venus-v2"; + reg = <0x0aa00000 0xff000>; + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&videocc VIDEO_CC_VENUS_CTL_CORE_CLK>, + <&videocc VIDEO_CC_VENUS_AHB_CLK>, + <&videocc VIDEO_CC_VENUS_CTL_AXI_CLK>, + <&videocc VIDEO_CC_VCODEC0_CORE_CLK>, + <&videocc VIDEO_CC_VCODEC0_AXI_CLK>, + <&videocc VIDEO_CC_VCODEC1_CORE_CLK>, + <&videocc VIDEO_CC_VCODEC1_AXI_CLK>; + clock-names = "core", "iface", "bus", + "vcodec0_core", "vcodec0_bus", + "vcodec1_core", "vcodec1_bus"; + power-domains = <&videocc VENUS_GDSC>, + <&videocc VCODEC0_GDSC>, + <&videocc VCODEC1_GDSC>; + power-domain-names = "venus", "vcodec0", "vcodec1"; + iommus = <&apps_smmu 0x10a0 0x8>, + <&apps_smmu 0x10b0 0x0>; + memory-region = <&venus_mem>; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sdm845-venus.yaml b/Documentation/devicetree/bindings/media/qcom,sdm845-venus.yaml new file mode 100644 index 000000000..eabc0957b --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sdm845-venus.yaml @@ -0,0 +1,131 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sdm845-venus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SDM845 Venus video encode and decode accelerators + +maintainers: + - Stanimir Varbanov <stanimir.varbanov@linaro.org> + +description: | + The Venus IP is a video encode and decode accelerator present + on Qualcomm platforms + +allOf: + - $ref: qcom,venus-common.yaml# + +properties: + compatible: + const: qcom,sdm845-venus + + power-domains: + maxItems: 1 + + clocks: + maxItems: 3 + + clock-names: + items: + - const: core + - const: iface + - const: bus + + iommus: + maxItems: 2 + + video-core0: + type: object + + properties: + compatible: + const: venus-decoder + + clocks: + maxItems: 2 + + clock-names: + items: + - const: core + - const: bus + + power-domains: + maxItems: 1 + + required: + - compatible + - clocks + - clock-names + - power-domains + + additionalProperties: false + + video-core1: + type: object + + properties: + compatible: + const: venus-encoder + + clocks: + maxItems: 2 + + clock-names: + items: + - const: core + - const: bus + + power-domains: + maxItems: 1 + + required: + - compatible + - clocks + - clock-names + - power-domains + + additionalProperties: false + +required: + - compatible + - iommus + - video-core0 + - video-core1 + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,videocc-sdm845.h> + + video-codec@aa00000 { + compatible = "qcom,sdm845-venus"; + reg = <0x0aa00000 0xff000>; + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&videocc VIDEO_CC_VENUS_CTL_CORE_CLK>, + <&videocc VIDEO_CC_VENUS_AHB_CLK>, + <&videocc VIDEO_CC_VENUS_CTL_AXI_CLK>; + clock-names = "core", "iface", "bus"; + power-domains = <&videocc VENUS_GDSC>; + iommus = <&apps_smmu 0x10a0 0x8>, + <&apps_smmu 0x10b0 0x0>; + memory-region = <&venus_mem>; + + video-core0 { + compatible = "venus-decoder"; + clocks = <&videocc VIDEO_CC_VCODEC0_CORE_CLK>, + <&videocc VIDEO_CC_VCODEC0_AXI_CLK>; + clock-names = "core", "bus"; + power-domains = <&videocc VCODEC0_GDSC>; + }; + + video-core1 { + compatible = "venus-encoder"; + clocks = <&videocc VIDEO_CC_VCODEC1_CORE_CLK>, + <&videocc VIDEO_CC_VCODEC1_AXI_CLK>; + clock-names = "core", "bus"; + power-domains = <&videocc VCODEC1_GDSC>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sm6150-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sm6150-camss.yaml new file mode 100644 index 000000000..ba7b0acb9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sm6150-camss.yaml @@ -0,0 +1,439 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sm6150-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SM6150 Camera Subsystem (CAMSS) + +maintainers: + - Wenmeng Liu <wenmeng.liu@oss.qualcomm.com> + +description: + This binding describes the camera subsystem hardware found on SM6150 + Qualcomm SoCs. It includes submodules such as CSIPHY (CSI Physical layer) + and CSID (CSI Decoder), which comply with the MIPI CSI2 protocol. + + The subsystem also integrates a set of real-time image processing engines + and their associated configuration modules, as well as non-real-time engines. + +properties: + compatible: + const: qcom,sm6150-camss + + reg: + items: + - description: Registers for CSID 0 + - description: Registers for CSID 1 + - description: Registers for CSID Lite + - description: Registers for CSIPHY 0 + - description: Registers for CSIPHY 1 + - description: Registers for CSIPHY 2 + - description: Registers for VFE 0 + - description: Registers for VFE 1 + - description: Registers for VFE Lite + - description: Registers for BPS (Bayer Processing Segment) + - description: Registers for CAMNOC + - description: Registers for CPAS CDM + - description: Registers for CPAS TOP + - description: Registers for ICP (Imaging Control Processor) CSR (Control and Status Registers) + - description: Registers for ICP QGIC (Qualcomm Generic Interrupt Controller) + - description: Registers for ICP SIERRA ((A5 subsystem communication)) + - description: Registers for IPE (Image Postprocessing Engine) 0 + - description: Registers for JPEG DMA + - description: Registers for JPEG ENC + - description: Registers for LRME (Low Resolution Motion Estimation) + + reg-names: + items: + - const: csid0 + - const: csid1 + - const: csid_lite + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: vfe0 + - const: vfe1 + - const: vfe_lite + - const: bps + - const: camnoc + - const: cpas_cdm + - const: cpas_top + - const: icp_csr + - const: icp_qgic + - const: icp_sierra + - const: ipe0 + - const: jpeg_dma + - const: jpeg_enc + - const: lrme + + clocks: + maxItems: 33 + + clock-names: + items: + - const: gcc_ahb + - const: gcc_axi_hf + - const: camnoc_axi + - const: cpas_ahb + - const: csiphy0 + - const: csiphy0_timer + - const: csiphy1 + - const: csiphy1_timer + - const: csiphy2 + - const: csiphy2_timer + - const: soc_ahb + - const: vfe0 + - const: vfe0_axi + - const: vfe0_cphy_rx + - const: vfe0_csid + - const: vfe1 + - const: vfe1_axi + - const: vfe1_cphy_rx + - const: vfe1_csid + - const: vfe_lite + - const: vfe_lite_cphy_rx + - const: vfe_lite_csid + - const: bps + - const: bps_ahb + - const: bps_axi + - const: bps_areg + - const: icp + - const: ipe0 + - const: ipe0_ahb + - const: ipe0_areg + - const: ipe0_axi + - const: jpeg + - const: lrme + + interrupts: + maxItems: 15 + + interrupt-names: + items: + - const: csid0 + - const: csid1 + - const: csid_lite + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: vfe0 + - const: vfe1 + - const: vfe_lite + - const: camnoc + - const: cdm + - const: icp + - const: jpeg_dma + - const: jpeg_enc + - const: lrme + + interconnects: + maxItems: 4 + + interconnect-names: + items: + - const: ahb + - const: hf_0 + - const: hf_1 + - const: sf_mnoc + + iommus: + items: + - description: Camera IFE 0 non-protected stream + - description: Camera IFE 1 non-protected stream + - description: Camera IFE 3 non-protected stream + - description: Camera CDM non-protected stream + - description: Camera LRME read non-protected stream + - description: Camera IPE 0 read non-protected stream + - description: Camera BPS read non-protected stream + - description: Camera IPE 0 write non-protected stream + - description: Camera BPS write non-protected stream + - description: Camera LRME write non-protected stream + - description: Camera JPEG read non-protected stream + - description: Camera JPEG write non-protected stream + - description: Camera ICP stream + + power-domains: + items: + - description: + IFE0 GDSC - Image Front End, Global Distributed Switch Controller. + - description: + IFE1 GDSC - Image Front End, Global Distributed Switch Controller. + - description: + Titan GDSC - Titan ISP Block, Global Distributed Switch Controller. + - description: + Titan BPS - Bayer Processing Segment, Global Distributed Switch Controller. + - description: + IPE GDSC - Image Postprocessing Engine, Global Distributed Switch Controller. + + power-domain-names: + items: + - const: ife0 + - const: ife1 + - const: top + - const: bps + - const: ipe + + vdd-csiphy-1p2-supply: + description: + Phandle to a 1.2V regulator supply to CSI PHYs. + + vdd-csiphy-1p8-supply: + description: + Phandle to 1.8V regulator supply to CSI PHYs pll block. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + patternProperties: + "^port@[0-2]$": + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + description: + Input port for receiving CSI data from a CSIPHY. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interrupts + - interrupt-names + - interconnects + - interconnect-names + - iommus + - power-domains + - power-domain-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,qcs615-camcc.h> + #include <dt-bindings/clock/qcom,qcs615-gcc.h> + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/interconnect/qcom,icc.h> + #include <dt-bindings/interconnect/qcom,qcs615-rpmh.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + camss: isp@acb3000 { + compatible = "qcom,sm6150-camss"; + + reg = <0x0 0x0acb3000 0x0 0x1000>, + <0x0 0x0acba000 0x0 0x1000>, + <0x0 0x0acc8000 0x0 0x1000>, + <0x0 0x0ac65000 0x0 0x1000>, + <0x0 0x0ac66000 0x0 0x1000>, + <0x0 0x0ac67000 0x0 0x1000>, + <0x0 0x0acaf000 0x0 0x4000>, + <0x0 0x0acb6000 0x0 0x4000>, + <0x0 0x0acc4000 0x0 0x4000>, + <0x0 0x0ac6f000 0x0 0x3000>, + <0x0 0x0ac42000 0x0 0x5000>, + <0x0 0x0ac48000 0x0 0x1000>, + <0x0 0x0ac40000 0x0 0x1000>, + <0x0 0x0ac18000 0x0 0x3000>, + <0x0 0x0ac00000 0x0 0x6000>, + <0x0 0x0ac10000 0x0 0x8000>, + <0x0 0x0ac87000 0x0 0x3000>, + <0x0 0x0ac52000 0x0 0x4000>, + <0x0 0x0ac4e000 0x0 0x4000>, + <0x0 0x0ac6b000 0x0 0x0a00>; + reg-names = "csid0", + "csid1", + "csid_lite", + "csiphy0", + "csiphy1", + "csiphy2", + "vfe0", + "vfe1", + "vfe_lite", + "bps", + "camnoc", + "cpas_cdm", + "cpas_top", + "icp_csr", + "icp_qgic", + "icp_sierra", + "ipe0", + "jpeg_dma", + "jpeg_enc", + "lrme"; + + clocks = <&gcc GCC_CAMERA_AHB_CLK>, + <&gcc GCC_CAMERA_HF_AXI_CLK>, + <&camcc CAM_CC_CAMNOC_AXI_CLK>, + <&camcc CAM_CC_CPAS_AHB_CLK>, + <&camcc CAM_CC_CSIPHY0_CLK>, + <&camcc CAM_CC_CSI0PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY1_CLK>, + <&camcc CAM_CC_CSI1PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY2_CLK>, + <&camcc CAM_CC_CSI2PHYTIMER_CLK>, + <&camcc CAM_CC_SOC_AHB_CLK>, + <&camcc CAM_CC_IFE_0_CLK>, + <&camcc CAM_CC_IFE_0_AXI_CLK>, + <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_0_CSID_CLK>, + <&camcc CAM_CC_IFE_1_CLK>, + <&camcc CAM_CC_IFE_1_AXI_CLK>, + <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_1_CSID_CLK>, + <&camcc CAM_CC_IFE_LITE_CLK>, + <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_LITE_CSID_CLK>, + <&camcc CAM_CC_BPS_CLK>, + <&camcc CAM_CC_BPS_AHB_CLK>, + <&camcc CAM_CC_BPS_AXI_CLK>, + <&camcc CAM_CC_BPS_AREG_CLK>, + <&camcc CAM_CC_ICP_CLK>, + <&camcc CAM_CC_IPE_0_CLK>, + <&camcc CAM_CC_IPE_0_AHB_CLK>, + <&camcc CAM_CC_IPE_0_AREG_CLK>, + <&camcc CAM_CC_IPE_0_AXI_CLK>, + <&camcc CAM_CC_JPEG_CLK>, + <&camcc CAM_CC_LRME_CLK>; + + clock-names = "gcc_ahb", + "gcc_axi_hf", + "camnoc_axi", + "cpas_ahb", + "csiphy0", + "csiphy0_timer", + "csiphy1", + "csiphy1_timer", + "csiphy2", + "csiphy2_timer", + "soc_ahb", + "vfe0", + "vfe0_axi", + "vfe0_cphy_rx", + "vfe0_csid", + "vfe1", + "vfe1_axi", + "vfe1_cphy_rx", + "vfe1_csid", + "vfe_lite", + "vfe_lite_cphy_rx", + "vfe_lite_csid", + "bps", + "bps_ahb", + "bps_axi", + "bps_areg", + "icp", + "ipe0", + "ipe0_ahb", + "ipe0_areg", + "ipe0_axi", + "jpeg", + "lrme"; + + interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY + &config_noc SLAVE_CAMERA_CFG QCOM_ICC_TAG_ACTIVE_ONLY>, + <&mmss_noc MASTER_CAMNOC_HF0 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, + <&mmss_noc MASTER_CAMNOC_HF1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, + <&mmss_noc MASTER_CAMNOC_SF QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "ahb", + "hf_0", + "hf_1", + "sf_mnoc"; + + interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 459 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 461 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 463 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 475 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 474 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 476 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "csid0", + "csid1", + "csid_lite", + "csiphy0", + "csiphy1", + "csiphy2", + "vfe0", + "vfe1", + "vfe_lite", + "camnoc", + "cdm", + "icp", + "jpeg_dma", + "jpeg_enc", + "lrme"; + + iommus = <&apps_smmu 0x0820 0x40>, + <&apps_smmu 0x0840 0x00>, + <&apps_smmu 0x0860 0x40>, + <&apps_smmu 0x0c00 0x00>, + <&apps_smmu 0x0cc0 0x00>, + <&apps_smmu 0x0c80 0x00>, + <&apps_smmu 0x0ca0 0x00>, + <&apps_smmu 0x0d00 0x00>, + <&apps_smmu 0x0d20 0x00>, + <&apps_smmu 0x0d40 0x00>, + <&apps_smmu 0x0d80 0x20>, + <&apps_smmu 0x0da0 0x20>, + <&apps_smmu 0x0de2 0x00>; + + power-domains = <&camcc IFE_0_GDSC>, + <&camcc IFE_1_GDSC>, + <&camcc TITAN_TOP_GDSC>, + <&camcc BPS_GDSC>, + <&camcc IPE_0_GDSC>; + power-domain-names = "ife0", + "ife1", + "top", + "bps", + "ipe"; + + vdd-csiphy-1p2-supply = <&vreg_l11a_1p2>; + vdd-csiphy-1p8-supply = <&vreg_l12a_1p8>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + csiphy_ep0: endpoint { + data-lanes = <0 1>; + remote-endpoint = <&sensor_ep>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sm6350-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sm6350-camss.yaml new file mode 100644 index 000000000..96974d90d --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sm6350-camss.yaml @@ -0,0 +1,471 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sm6350-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SM6350 Camera Subsystem (CAMSS) + +maintainers: + - Luca Weiss <luca.weiss@fairphone.com> + +description: + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms. + +properties: + compatible: + const: qcom,sm6350-camss + + reg: + maxItems: 24 + + reg-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid_lite + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: vfe0 + - const: vfe1 + - const: vfe2 + - const: vfe_lite + - const: a5_csr + - const: a5_qgic + - const: a5_sierra + - const: bps + - const: camnoc + - const: core_top_csr_tcsr + - const: cpas_cdm + - const: cpas_top + - const: ipe + - const: jpeg_dma + - const: jpeg_enc + - const: lrme + + clocks: + maxItems: 39 + + clock-names: + items: + - const: cam_axi + - const: soc_ahb + - const: camnoc_axi + - const: core_ahb + - const: cpas_ahb + - const: csiphy0 + - const: csiphy0_timer + - const: csiphy1 + - const: csiphy1_timer + - const: csiphy2 + - const: csiphy2_timer + - const: csiphy3 + - const: csiphy3_timer + - const: vfe0_axi + - const: vfe0 + - const: vfe0_cphy_rx + - const: vfe0_csid + - const: vfe1_axi + - const: vfe1 + - const: vfe1_cphy_rx + - const: vfe1_csid + - const: vfe2_axi + - const: vfe2 + - const: vfe2_cphy_rx + - const: vfe2_csid + - const: vfe_lite + - const: vfe_lite_cphy_rx + - const: vfe_lite_csid + - const: bps + - const: bps_ahb + - const: bps_areg + - const: bps_axi + - const: icp + - const: ipe0 + - const: ipe0_ahb + - const: ipe0_areg + - const: ipe0_axi + - const: jpeg + - const: lrme + + interrupts: + maxItems: 18 + + interrupt-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid_lite + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: vfe0 + - const: vfe1 + - const: vfe2 + - const: vfe_lite + - const: a5 + - const: cpas + - const: cpas_cdm + - const: jpeg_dma + - const: jpeg_enc + - const: lrme + + interconnects: + maxItems: 4 + + interconnect-names: + items: + - const: ahb + - const: hf_mnoc + - const: sf_mnoc + - const: sf_icp_mnoc + + iommus: + maxItems: 14 + + power-domains: + maxItems: 6 + + power-domain-names: + items: + - const: ife0 + - const: ife1 + - const: ife2 + - const: top + - const: bps + - const: ipe + + vdd-csiphy0-0p9-supply: + description: + Phandle to a 0.9V regulator supply to CSIPHY0. + + vdd-csiphy0-1p25-supply: + description: + Phandle to a 1.25V regulator supply to CSIPHY0. + + vdd-csiphy1-0p9-supply: + description: + Phandle to a 0.9V regulator supply to CSIPHY1. + + vdd-csiphy1-1p25-supply: + description: + Phandle to a 1.25V regulator supply to CSIPHY1. + + vdd-csiphy2-0p9-supply: + description: + Phandle to a 0.9V regulator supply to CSIPHY2. + + vdd-csiphy2-1p25-supply: + description: + Phandle to a 1.25V regulator supply to CSIPHY2. + + vdd-csiphy3-0p9-supply: + description: + Phandle to a 0.9V regulator supply to CSIPHY3. + + vdd-csiphy3-1p25-supply: + description: + Phandle to a 1.25V regulator supply to CSIPHY3. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + patternProperties: + "^port@[0-3]$": + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + description: + Input port for receiving CSI data from a CSIPHY. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interrupts + - interrupt-names + - interconnects + - interconnect-names + - iommus + - power-domains + - power-domain-names + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-sm6350.h> + #include <dt-bindings/clock/qcom,sm6350-camcc.h> + #include <dt-bindings/interconnect/qcom,icc.h> + #include <dt-bindings/interconnect/qcom,sm6350.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/media/video-interfaces.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + isp@acb3000 { + compatible = "qcom,sm6350-camss"; + + reg = <0x0 0x0acb3000 0x0 0x1000>, + <0x0 0x0acba000 0x0 0x1000>, + <0x0 0x0acc1000 0x0 0x1000>, + <0x0 0x0acc8000 0x0 0x1000>, + <0x0 0x0ac65000 0x0 0x1000>, + <0x0 0x0ac66000 0x0 0x1000>, + <0x0 0x0ac67000 0x0 0x1000>, + <0x0 0x0ac68000 0x0 0x1000>, + <0x0 0x0acaf000 0x0 0x4000>, + <0x0 0x0acb6000 0x0 0x4000>, + <0x0 0x0acbd000 0x0 0x4000>, + <0x0 0x0acc4000 0x0 0x4000>, + <0x0 0x0ac18000 0x0 0x3000>, + <0x0 0x0ac00000 0x0 0x6000>, + <0x0 0x0ac10000 0x0 0x8000>, + <0x0 0x0ac6f000 0x0 0x8000>, + <0x0 0x0ac42000 0x0 0x4600>, + <0x0 0x01fc0000 0x0 0x40000>, + <0x0 0x0ac48000 0x0 0x1000>, + <0x0 0x0ac40000 0x0 0x1000>, + <0x0 0x0ac87000 0x0 0xa000>, + <0x0 0x0ac52000 0x0 0x4000>, + <0x0 0x0ac4e000 0x0 0x4000>, + <0x0 0x0ac6b000 0x0 0xa00>; + reg-names = "csid0", + "csid1", + "csid2", + "csid_lite", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "vfe0", + "vfe1", + "vfe2", + "vfe_lite", + "a5_csr", + "a5_qgic", + "a5_sierra", + "bps", + "camnoc", + "core_top_csr_tcsr", + "cpas_cdm", + "cpas_top", + "ipe", + "jpeg_dma", + "jpeg_enc", + "lrme"; + + clocks = <&gcc GCC_CAMERA_AXI_CLK>, + <&camcc CAMCC_SOC_AHB_CLK>, + <&camcc CAMCC_CAMNOC_AXI_CLK>, + <&camcc CAMCC_CORE_AHB_CLK>, + <&camcc CAMCC_CPAS_AHB_CLK>, + <&camcc CAMCC_CSIPHY0_CLK>, + <&camcc CAMCC_CSI0PHYTIMER_CLK>, + <&camcc CAMCC_CSIPHY1_CLK>, + <&camcc CAMCC_CSI1PHYTIMER_CLK>, + <&camcc CAMCC_CSIPHY2_CLK>, + <&camcc CAMCC_CSI2PHYTIMER_CLK>, + <&camcc CAMCC_CSIPHY3_CLK>, + <&camcc CAMCC_CSI3PHYTIMER_CLK>, + <&camcc CAMCC_IFE_0_AXI_CLK>, + <&camcc CAMCC_IFE_0_CLK>, + <&camcc CAMCC_IFE_0_CPHY_RX_CLK>, + <&camcc CAMCC_IFE_0_CSID_CLK>, + <&camcc CAMCC_IFE_1_AXI_CLK>, + <&camcc CAMCC_IFE_1_CLK>, + <&camcc CAMCC_IFE_1_CPHY_RX_CLK>, + <&camcc CAMCC_IFE_1_CSID_CLK>, + <&camcc CAMCC_IFE_2_AXI_CLK>, + <&camcc CAMCC_IFE_2_CLK>, + <&camcc CAMCC_IFE_2_CPHY_RX_CLK>, + <&camcc CAMCC_IFE_2_CSID_CLK>, + <&camcc CAMCC_IFE_LITE_CLK>, + <&camcc CAMCC_IFE_LITE_CPHY_RX_CLK>, + <&camcc CAMCC_IFE_LITE_CSID_CLK>, + <&camcc CAMCC_BPS_CLK>, + <&camcc CAMCC_BPS_AHB_CLK>, + <&camcc CAMCC_BPS_AREG_CLK>, + <&camcc CAMCC_BPS_AXI_CLK>, + <&camcc CAMCC_ICP_CLK>, + <&camcc CAMCC_IPE_0_CLK>, + <&camcc CAMCC_IPE_0_AHB_CLK>, + <&camcc CAMCC_IPE_0_AREG_CLK>, + <&camcc CAMCC_IPE_0_AXI_CLK>, + <&camcc CAMCC_JPEG_CLK>, + <&camcc CAMCC_LRME_CLK>; + clock-names = "cam_axi", + "soc_ahb", + "camnoc_axi", + "core_ahb", + "cpas_ahb", + "csiphy0", + "csiphy0_timer", + "csiphy1", + "csiphy1_timer", + "csiphy2", + "csiphy2_timer", + "csiphy3", + "csiphy3_timer", + "vfe0_axi", + "vfe0", + "vfe0_cphy_rx", + "vfe0_csid", + "vfe1_axi", + "vfe1", + "vfe1_cphy_rx", + "vfe1_csid", + "vfe2_axi", + "vfe2", + "vfe2_cphy_rx", + "vfe2_csid", + "vfe_lite", + "vfe_lite_cphy_rx", + "vfe_lite_csid", + "bps", + "bps_ahb", + "bps_areg", + "bps_axi", + "icp", + "ipe0", + "ipe0_ahb", + "ipe0_areg", + "ipe0_axi", + "jpeg", + "lrme"; + + interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 717 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 473 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 461 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 718 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 472 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 463 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 459 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 475 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 474 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 476 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "csid0", + "csid1", + "csid2", + "csid_lite", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "vfe0", + "vfe1", + "vfe2", + "vfe_lite", + "a5", + "cpas", + "cpas_cdm", + "jpeg_dma", + "jpeg_enc", + "lrme"; + + interconnects = <&gem_noc MASTER_AMPSS_M0 QCOM_ICC_TAG_ACTIVE_ONLY + &config_noc SLAVE_CAMERA_CFG QCOM_ICC_TAG_ACTIVE_ONLY>, + <&mmss_noc MASTER_CAMNOC_HF QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_EBI_CH0 QCOM_ICC_TAG_ALWAYS>, + <&mmss_noc MASTER_CAMNOC_SF QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_EBI_CH0 QCOM_ICC_TAG_ALWAYS>, + <&mmss_noc MASTER_CAMNOC_ICP QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_EBI_CH0 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "ahb", + "hf_mnoc", + "sf_mnoc", + "sf_icp_mnoc"; + + iommus = <&apps_smmu 0x820 0xc0>, + <&apps_smmu 0x840 0x0>, + <&apps_smmu 0x860 0xc0>, + <&apps_smmu 0x880 0x0>, + <&apps_smmu 0xc40 0x20>, + <&apps_smmu 0xc60 0x20>, + <&apps_smmu 0xc80 0x0>, + <&apps_smmu 0xca2 0x0>, + <&apps_smmu 0xcc0 0x20>, + <&apps_smmu 0xce0 0x20>, + <&apps_smmu 0xd00 0x20>, + <&apps_smmu 0xd20 0x20>, + <&apps_smmu 0xd40 0x20>, + <&apps_smmu 0xd60 0x20>; + + power-domains = <&camcc IFE_0_GDSC>, + <&camcc IFE_1_GDSC>, + <&camcc IFE_2_GDSC>, + <&camcc TITAN_TOP_GDSC>, + <&camcc BPS_GDSC>, + <&camcc IPE_0_GDSC>; + power-domain-names = "ife0", + "ife1", + "ife2", + "top", + "bps", + "ipe"; + + vdd-csiphy0-0p9-supply = <&vreg_l18a>; + vdd-csiphy0-1p25-supply = <&vreg_l22a>; + vdd-csiphy1-0p9-supply = <&vreg_l18a>; + vdd-csiphy1-1p25-supply = <&vreg_l22a>; + vdd-csiphy2-0p9-supply = <&vreg_l18a>; + vdd-csiphy2-1p25-supply = <&vreg_l22a>; + vdd-csiphy3-0p9-supply = <&vreg_l18a>; + vdd-csiphy3-1p25-supply = <&vreg_l22a>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + csiphy0_ep: endpoint { + data-lanes = <0 1 2 3>; + bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>; + remote-endpoint = <&sensor_ep>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sm8250-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sm8250-camss.yaml new file mode 100644 index 000000000..a509d4bbc --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sm8250-camss.yaml @@ -0,0 +1,492 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sm8250-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm CAMSS ISP + +maintainers: + - Robert Foss <robert.foss@linaro.org> + +description: | + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms. + +properties: + compatible: + const: qcom,sm8250-camss + + clocks: + minItems: 37 + maxItems: 37 + + clock-names: + items: + - const: cam_ahb_clk + - const: cam_hf_axi + - const: cam_sf_axi + - const: camnoc_axi + - const: camnoc_axi_src + - const: core_ahb + - const: cpas_ahb + - const: csiphy0 + - const: csiphy0_timer + - const: csiphy1 + - const: csiphy1_timer + - const: csiphy2 + - const: csiphy2_timer + - const: csiphy3 + - const: csiphy3_timer + - const: csiphy4 + - const: csiphy4_timer + - const: csiphy5 + - const: csiphy5_timer + - const: slow_ahb_src + - const: vfe0_ahb + - const: vfe0_axi + - const: vfe0 + - const: vfe0_cphy_rx + - const: vfe0_csid + - const: vfe0_areg + - const: vfe1_ahb + - const: vfe1_axi + - const: vfe1 + - const: vfe1_cphy_rx + - const: vfe1_csid + - const: vfe1_areg + - const: vfe_lite_ahb + - const: vfe_lite_axi + - const: vfe_lite + - const: vfe_lite_cphy_rx + - const: vfe_lite_csid + + interrupts: + minItems: 14 + maxItems: 14 + + interrupt-names: + items: + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: csiphy4 + - const: csiphy5 + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid3 + - const: vfe0 + - const: vfe1 + - const: vfe_lite0 + - const: vfe_lite1 + + iommus: + minItems: 8 + maxItems: 8 + + interconnects: + minItems: 4 + maxItems: 4 + + interconnect-names: + items: + - const: cam_ahb + - const: cam_hf_0_mnoc + - const: cam_sf_0_mnoc + - const: cam_sf_icp_mnoc + + power-domains: + items: + - description: IFE0 GDSC - Image Front End, Global Distributed Switch Controller. + - description: IFE1 GDSC - Image Front End, Global Distributed Switch Controller. + - description: Titan GDSC - Titan ISP Block, Global Distributed Switch Controller. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@3: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@4: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@5: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + reg: + minItems: 10 + maxItems: 10 + + reg-names: + items: + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: csiphy4 + - const: csiphy5 + - const: vfe0 + - const: vfe1 + - const: vfe_lite0 + - const: vfe_lite1 + + vdda-phy-supply: + description: + 0.88V supply to CSIPHY IP blocks. + + vdda-pll-supply: + description: + 1.2V supply to CSIPHY IP blocks. + +required: + - clock-names + - clocks + - compatible + - interconnects + - interconnect-names + - interrupts + - interrupt-names + - iommus + - power-domains + - reg + - reg-names + - vdda-phy-supply + - vdda-pll-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,camcc-sm8250.h> + #include <dt-bindings/interconnect/qcom,sm8250.h> + #include <dt-bindings/clock/qcom,gcc-sm8250.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + camss: camss@ac6a000 { + compatible = "qcom,sm8250-camss"; + + reg = <0 0xac6a000 0 0x2000>, + <0 0xac6c000 0 0x2000>, + <0 0xac6e000 0 0x1000>, + <0 0xac70000 0 0x1000>, + <0 0xac72000 0 0x1000>, + <0 0xac74000 0 0x1000>, + <0 0xacb4000 0 0xd000>, + <0 0xacc3000 0 0xd000>, + <0 0xacd9000 0 0x2200>, + <0 0xacdb200 0 0x2200>; + reg-names = "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "csiphy4", + "csiphy5", + "vfe0", + "vfe1", + "vfe_lite0", + "vfe_lite1"; + + vdda-phy-supply = <&vreg_l5a_0p88>; + vdda-pll-supply = <&vreg_l9a_1p2>; + + interrupts = <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 448 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 86 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 89 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 359 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 360 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "csiphy4", + "csiphy5", + "csid0", + "csid1", + "csid2", + "csid3", + "vfe0", + "vfe1", + "vfe_lite0", + "vfe_lite1"; + + power-domains = <&camcc IFE_0_GDSC>, + <&camcc IFE_1_GDSC>, + <&camcc TITAN_TOP_GDSC>; + + clocks = <&gcc GCC_CAMERA_AHB_CLK>, + <&gcc GCC_CAMERA_HF_AXI_CLK>, + <&gcc GCC_CAMERA_SF_AXI_CLK>, + <&camcc CAM_CC_CAMNOC_AXI_CLK>, + <&camcc CAM_CC_CAMNOC_AXI_CLK_SRC>, + <&camcc CAM_CC_CORE_AHB_CLK>, + <&camcc CAM_CC_CPAS_AHB_CLK>, + <&camcc CAM_CC_CSIPHY0_CLK>, + <&camcc CAM_CC_CSI0PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY1_CLK>, + <&camcc CAM_CC_CSI1PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY2_CLK>, + <&camcc CAM_CC_CSI2PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY3_CLK>, + <&camcc CAM_CC_CSI3PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY4_CLK>, + <&camcc CAM_CC_CSI4PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY5_CLK>, + <&camcc CAM_CC_CSI5PHYTIMER_CLK>, + <&camcc CAM_CC_SLOW_AHB_CLK_SRC>, + <&camcc CAM_CC_IFE_0_AHB_CLK>, + <&camcc CAM_CC_IFE_0_AXI_CLK>, + <&camcc CAM_CC_IFE_0_CLK>, + <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_0_CSID_CLK>, + <&camcc CAM_CC_IFE_0_AREG_CLK>, + <&camcc CAM_CC_IFE_1_AHB_CLK>, + <&camcc CAM_CC_IFE_1_AXI_CLK>, + <&camcc CAM_CC_IFE_1_CLK>, + <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_1_CSID_CLK>, + <&camcc CAM_CC_IFE_1_AREG_CLK>, + <&camcc CAM_CC_IFE_LITE_AHB_CLK>, + <&camcc CAM_CC_IFE_LITE_AXI_CLK>, + <&camcc CAM_CC_IFE_LITE_CLK>, + <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_LITE_CSID_CLK>; + clock-names = "cam_ahb_clk", + "cam_hf_axi", + "cam_sf_axi", + "camnoc_axi", + "camnoc_axi_src", + "core_ahb", + "cpas_ahb", + "csiphy0", + "csiphy0_timer", + "csiphy1", + "csiphy1_timer", + "csiphy2", + "csiphy2_timer", + "csiphy3", + "csiphy3_timer", + "csiphy4", + "csiphy4_timer", + "csiphy5", + "csiphy5_timer", + "slow_ahb_src", + "vfe0_ahb", + "vfe0_axi", + "vfe0", + "vfe0_cphy_rx", + "vfe0_csid", + "vfe0_areg", + "vfe1_ahb", + "vfe1_axi", + "vfe1", + "vfe1_cphy_rx", + "vfe1_csid", + "vfe1_areg", + "vfe_lite_ahb", + "vfe_lite_axi", + "vfe_lite", + "vfe_lite_cphy_rx", + "vfe_lite_csid"; + + iommus = <&apps_smmu 0x800 0x400>, + <&apps_smmu 0x801 0x400>, + <&apps_smmu 0x840 0x400>, + <&apps_smmu 0x841 0x400>, + <&apps_smmu 0xC00 0x400>, + <&apps_smmu 0xC01 0x400>, + <&apps_smmu 0xC40 0x400>, + <&apps_smmu 0xC41 0x400>; + + interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_CAMERA_CFG>, + <&mmss_noc MASTER_CAMNOC_HF &mc_virt SLAVE_EBI_CH0>, + <&mmss_noc MASTER_CAMNOC_SF &mc_virt SLAVE_EBI_CH0>, + <&mmss_noc MASTER_CAMNOC_ICP &mc_virt SLAVE_EBI_CH0>; + interconnect-names = "cam_ahb", + "cam_hf_0_mnoc", + "cam_sf_0_mnoc", + "cam_sf_icp_mnoc"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sm8250-venus.yaml b/Documentation/devicetree/bindings/media/qcom,sm8250-venus.yaml new file mode 100644 index 000000000..aca748e42 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sm8250-venus.yaml @@ -0,0 +1,146 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sm8250-venus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SM8250 Venus video encode and decode accelerators + +maintainers: + - Stanimir Varbanov <stanimir.varbanov@linaro.org> + +description: | + The Iris v2.xx IP is a video encode and decode accelerator present on + Qualcomm platforms + +allOf: + - $ref: qcom,venus-common.yaml# + +properties: + compatible: + oneOf: + - const: qcom,sm8250-venus + - items: + - enum: + - qcom,sc8280xp-iris + - qcom,sm8350-iris + - const: qcom,sm8250-venus + + power-domains: + minItems: 2 + maxItems: 4 + + power-domain-names: + minItems: 2 + items: + - const: venus + - const: vcodec0 + - const: mx + - const: mmcx + + clocks: + maxItems: 3 + + clock-names: + items: + - const: iface + - const: core + - const: vcodec0_core + + iommus: + maxItems: 1 + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: cpu-cfg + - const: video-mem + + operating-points-v2: true + opp-table: + type: object + + resets: + maxItems: 2 + + reset-names: + items: + - const: bus + - const: core + + video-decoder: + type: object + + properties: + compatible: + const: venus-decoder + + required: + - compatible + + deprecated: true + additionalProperties: false + + video-encoder: + type: object + + properties: + compatible: + const: venus-encoder + + required: + - compatible + + deprecated: true + additionalProperties: false + +required: + - compatible + - power-domain-names + - interconnects + - interconnect-names + - iommus + - resets + - reset-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,videocc-sm8250.h> + #include <dt-bindings/interconnect/qcom,sm8250.h> + #include <dt-bindings/clock/qcom,gcc-sm8250.h> + #include <dt-bindings/power/qcom,rpmhpd.h> + + venus: video-codec@aa00000 { + compatible = "qcom,sm8250-venus"; + reg = <0x0aa00000 0xff000>; + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&videocc MVS0C_GDSC>, + <&videocc MVS0_GDSC>, + <&rpmhpd RPMHPD_MX>, + <&rpmhpd RPMHPD_MMCX>; + power-domain-names = "venus", + "vcodec0", + "mx", + "mmcx"; + + clocks = <&gcc GCC_VIDEO_AXI0_CLK>, + <&videocc VIDEO_CC_MVS0C_CLK>, + <&videocc VIDEO_CC_MVS0_CLK>; + clock-names = "iface", "core", "vcodec0_core"; + + interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_VENUS_CFG>, + <&mmss_noc MASTER_VIDEO_P0 &mc_virt SLAVE_EBI_CH0>; + interconnect-names = "cpu-cfg", "video-mem"; + + iommus = <&apps_smmu 0x2100 0x0400>; + memory-region = <&video_mem>; + + resets = <&gcc GCC_VIDEO_AXI0_CLK_ARES>, + <&videocc VIDEO_CC_MVS0C_CLK_ARES>; + reset-names = "bus", "core"; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sm8550-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sm8550-camss.yaml new file mode 100644 index 000000000..4b9ab1352 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sm8550-camss.yaml @@ -0,0 +1,597 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sm8550-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SM8550 Camera Subsystem (CAMSS) + +maintainers: + - Depeng Shao <quic_depengs@quicinc.com> + +description: + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms. + +properties: + compatible: + const: qcom,sm8550-camss + + reg: + maxItems: 19 + + reg-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid_lite0 + - const: csid_lite1 + - const: csid_wrapper + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: csiphy4 + - const: csiphy5 + - const: csiphy6 + - const: csiphy7 + - const: vfe0 + - const: vfe1 + - const: vfe2 + - const: vfe_lite0 + - const: vfe_lite1 + + clocks: + maxItems: 36 + + clock-names: + items: + - const: camnoc_axi + - const: cpas_ahb + - const: cpas_fast_ahb_clk + - const: cpas_ife_lite + - const: cpas_vfe0 + - const: cpas_vfe1 + - const: cpas_vfe2 + - const: csid + - const: csiphy0 + - const: csiphy0_timer + - const: csiphy1 + - const: csiphy1_timer + - const: csiphy2 + - const: csiphy2_timer + - const: csiphy3 + - const: csiphy3_timer + - const: csiphy4 + - const: csiphy4_timer + - const: csiphy5 + - const: csiphy5_timer + - const: csiphy6 + - const: csiphy6_timer + - const: csiphy7 + - const: csiphy7_timer + - const: csiphy_rx + - const: gcc_axi_hf + - const: vfe0 + - const: vfe0_fast_ahb + - const: vfe1 + - const: vfe1_fast_ahb + - const: vfe2 + - const: vfe2_fast_ahb + - const: vfe_lite + - const: vfe_lite_ahb + - const: vfe_lite_cphy_rx + - const: vfe_lite_csid + + interrupts: + maxItems: 18 + + interrupt-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid_lite0 + - const: csid_lite1 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: csiphy4 + - const: csiphy5 + - const: csiphy6 + - const: csiphy7 + - const: vfe0 + - const: vfe1 + - const: vfe2 + - const: vfe_lite0 + - const: vfe_lite1 + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: ahb + - const: hf_0_mnoc + + iommus: + maxItems: 1 + + power-domains: + items: + - description: IFE0 GDSC - Image Front End, Global Distributed Switch Controller. + - description: IFE1 GDSC - Image Front End, Global Distributed Switch Controller. + - description: IFE2 GDSC - Image Front End, Global Distributed Switch Controller. + - description: Titan GDSC - Titan ISP Block, Global Distributed Switch Controller. + + power-domain-names: + items: + - const: ife0 + - const: ife1 + - const: ife2 + - const: top + + vdda-phy-supply: + description: + 0.88V supply to CSIPHY IP blocks. + + vdda-pll-supply: + description: + 1.2V supply to CSIPHY IP blocks. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSI0. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSI1. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSI2. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@3: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSI3. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@4: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSI4. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@5: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSI5. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@6: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSI6. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + + port@7: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port for receiving CSI data on CSI7. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - clock-lanes + - data-lanes + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interrupts + - interrupt-names + - interconnects + - interconnect-names + - iommus + - power-domains + - power-domain-names + - vdda-phy-supply + - vdda-pll-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/clock/qcom,sm8550-camcc.h> + #include <dt-bindings/clock/qcom,sm8550-gcc.h> + #include <dt-bindings/interconnect/qcom,icc.h> + #include <dt-bindings/interconnect/qcom,sm8550-rpmh.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + isp@acb7000 { + compatible = "qcom,sm8550-camss"; + + reg = <0 0x0acb7000 0 0xd00>, + <0 0x0acb9000 0 0xd00>, + <0 0x0acbb000 0 0xd00>, + <0 0x0acca000 0 0xa00>, + <0 0x0acce000 0 0xa00>, + <0 0x0acb6000 0 0x1000>, + <0 0x0ace4000 0 0x2000>, + <0 0x0ace6000 0 0x2000>, + <0 0x0ace8000 0 0x2000>, + <0 0x0acea000 0 0x2000>, + <0 0x0acec000 0 0x2000>, + <0 0x0acee000 0 0x2000>, + <0 0x0acf0000 0 0x2000>, + <0 0x0acf2000 0 0x2000>, + <0 0x0ac62000 0 0xf000>, + <0 0x0ac71000 0 0xf000>, + <0 0x0ac80000 0 0xf000>, + <0 0x0accb000 0 0x1800>, + <0 0x0accf000 0 0x1800>; + reg-names = "csid0", + "csid1", + "csid2", + "csid_lite0", + "csid_lite1", + "csid_wrapper", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "csiphy4", + "csiphy5", + "csiphy6", + "csiphy7", + "vfe0", + "vfe1", + "vfe2", + "vfe_lite0", + "vfe_lite1"; + + clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>, + <&camcc CAM_CC_CPAS_AHB_CLK>, + <&camcc CAM_CC_CPAS_FAST_AHB_CLK>, + <&camcc CAM_CC_CPAS_IFE_LITE_CLK>, + <&camcc CAM_CC_CPAS_IFE_0_CLK>, + <&camcc CAM_CC_CPAS_IFE_1_CLK>, + <&camcc CAM_CC_CPAS_IFE_2_CLK>, + <&camcc CAM_CC_CSID_CLK>, + <&camcc CAM_CC_CSIPHY0_CLK>, + <&camcc CAM_CC_CSI0PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY1_CLK>, + <&camcc CAM_CC_CSI1PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY2_CLK>, + <&camcc CAM_CC_CSI2PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY3_CLK>, + <&camcc CAM_CC_CSI3PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY4_CLK>, + <&camcc CAM_CC_CSI4PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY5_CLK>, + <&camcc CAM_CC_CSI5PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY6_CLK>, + <&camcc CAM_CC_CSI6PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY7_CLK>, + <&camcc CAM_CC_CSI7PHYTIMER_CLK>, + <&camcc CAM_CC_CSID_CSIPHY_RX_CLK>, + <&gcc GCC_CAMERA_HF_AXI_CLK>, + <&camcc CAM_CC_IFE_0_CLK>, + <&camcc CAM_CC_IFE_0_FAST_AHB_CLK>, + <&camcc CAM_CC_IFE_1_CLK>, + <&camcc CAM_CC_IFE_1_FAST_AHB_CLK>, + <&camcc CAM_CC_IFE_2_CLK>, + <&camcc CAM_CC_IFE_2_FAST_AHB_CLK>, + <&camcc CAM_CC_IFE_LITE_CLK>, + <&camcc CAM_CC_IFE_LITE_AHB_CLK>, + <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_LITE_CSID_CLK>; + clock-names = "camnoc_axi", + "cpas_ahb", + "cpas_fast_ahb_clk", + "cpas_ife_lite", + "cpas_vfe0", + "cpas_vfe1", + "cpas_vfe2", + "csid", + "csiphy0", + "csiphy0_timer", + "csiphy1", + "csiphy1_timer", + "csiphy2", + "csiphy2_timer", + "csiphy3", + "csiphy3_timer", + "csiphy4", + "csiphy4_timer", + "csiphy5", + "csiphy5_timer", + "csiphy6", + "csiphy6_timer", + "csiphy7", + "csiphy7_timer", + "csiphy_rx", + "gcc_axi_hf", + "vfe0", + "vfe0_fast_ahb", + "vfe1", + "vfe1_fast_ahb", + "vfe2", + "vfe2_fast_ahb", + "vfe_lite", + "vfe_lite_ahb", + "vfe_lite_cphy_rx", + "vfe_lite_csid"; + + interrupts = <GIC_SPI 601 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 603 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 431 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 605 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 376 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 448 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 122 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 89 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 278 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 277 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 602 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 604 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 688 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 606 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 377 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "csid0", + "csid1", + "csid2", + "csid_lite0", + "csid_lite1", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "csiphy4", + "csiphy5", + "csiphy6", + "csiphy7", + "vfe0", + "vfe1", + "vfe2", + "vfe_lite0", + "vfe_lite1"; + + interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY + &config_noc SLAVE_CAMERA_CFG QCOM_ICC_TAG_ACTIVE_ONLY>, + <&mmss_noc MASTER_CAMNOC_HF QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "ahb", + "hf_0_mnoc"; + + iommus = <&apps_smmu 0x800 0x20>; + + power-domains = <&camcc CAM_CC_IFE_0_GDSC>, + <&camcc CAM_CC_IFE_1_GDSC>, + <&camcc CAM_CC_IFE_2_GDSC>, + <&camcc CAM_CC_TITAN_TOP_GDSC>; + power-domain-names = "ife0", + "ife1", + "ife2", + "top"; + + vdda-phy-supply = <&vreg_l1e_0p88>; + vdda-pll-supply = <&vreg_l3e_1p2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + csiphy_ep0: endpoint@0 { + reg = <0>; + clock-lanes = <7>; + data-lanes = <0 1>; + remote-endpoint = <&sensor_ep>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sm8550-iris.yaml b/Documentation/devicetree/bindings/media/qcom,sm8550-iris.yaml new file mode 100644 index 000000000..0400ca1bf --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sm8550-iris.yaml @@ -0,0 +1,220 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sm8550-iris.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm iris video encode and decode accelerators + +maintainers: + - Vikash Garodia <quic_vgarodia@quicinc.com> + - Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com> + +description: + The iris video processing unit is a video encode and decode accelerator + present on Qualcomm platforms. + +properties: + compatible: + oneOf: + - items: + - enum: + - qcom,sa8775p-iris + - qcom,x1e80100-iris + - const: qcom,sm8550-iris + - enum: + - qcom,qcs8300-iris + - qcom,sm8550-iris + - qcom,sm8650-iris + - qcom,x1p42100-iris + + reg: + maxItems: 1 + + power-domains: + maxItems: 4 + + power-domain-names: + items: + - const: venus + - const: vcodec0 + - const: mxc + - const: mmcx + + clocks: + minItems: 3 + maxItems: 4 + + clock-names: + minItems: 3 + items: + - const: iface + - const: core + - const: vcodec0_core + - const: vcodec0_bse + + firmware-name: + maxItems: 1 + + interrupts: + maxItems: 1 + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: cpu-cfg + - const: video-mem + + resets: + minItems: 1 + maxItems: 3 + + reset-names: + minItems: 1 + items: + - const: bus + - const: xo + - const: core + + iommus: + maxItems: 2 + + dma-coherent: true + + memory-region: + maxItems: 1 + + operating-points-v2: true + + opp-table: + type: object + +required: + - compatible + - power-domain-names + - interconnects + - interconnect-names + - resets + - reset-names + - iommus + - dma-coherent + +allOf: + - if: + properties: + compatible: + enum: + - qcom,sm8650-iris + then: + properties: + resets: + minItems: 3 + reset-names: + minItems: 3 + else: + properties: + resets: + maxItems: 1 + reset-names: + maxItems: 1 + - if: + properties: + compatible: + enum: + - qcom,x1p42100-iris + then: + properties: + clocks: + minItems: 4 + clock-names: + minItems: 4 + else: + properties: + clocks: + maxItems: 3 + clock-names: + maxItems: 3 + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/clock/qcom,sm8550-gcc.h> + #include <dt-bindings/clock/qcom,sm8450-videocc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interconnect/qcom,icc.h> + #include <dt-bindings/interconnect/qcom,sm8550-rpmh.h> + #include <dt-bindings/power/qcom-rpmpd.h> + #include <dt-bindings/power/qcom,rpmhpd.h> + + video-codec@aa00000 { + compatible = "qcom,sm8550-iris"; + reg = <0x0aa00000 0xf0000>; + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + + power-domains = <&videocc VIDEO_CC_MVS0C_GDSC>, + <&videocc VIDEO_CC_MVS0_GDSC>, + <&rpmhpd RPMHPD_MXC>, + <&rpmhpd RPMHPD_MMCX>; + power-domain-names = "venus", "vcodec0", "mxc", "mmcx"; + + clocks = <&gcc GCC_VIDEO_AXI0_CLK>, + <&videocc VIDEO_CC_MVS0C_CLK>, + <&videocc VIDEO_CC_MVS0_CLK>; + clock-names = "iface", "core", "vcodec0_core"; + + interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_VENUS_CFG QCOM_ICC_TAG_ALWAYS>, + <&mmss_noc MASTER_VIDEO QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "cpu-cfg", "video-mem"; + + memory-region = <&video_mem>; + + resets = <&gcc GCC_VIDEO_AXI0_CLK_ARES>; + reset-names = "bus"; + + iommus = <&apps_smmu 0x1940 0x0000>, + <&apps_smmu 0x1947 0x0000>; + dma-coherent; + + operating-points-v2 = <&iris_opp_table>; + + iris_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-240000000 { + opp-hz = /bits/ 64 <240000000>; + required-opps = <&rpmhpd_opp_svs>, + <&rpmhpd_opp_low_svs>; + }; + + opp-338000000 { + opp-hz = /bits/ 64 <338000000>; + required-opps = <&rpmhpd_opp_svs>, + <&rpmhpd_opp_svs>; + }; + + opp-366000000 { + opp-hz = /bits/ 64 <366000000>; + required-opps = <&rpmhpd_opp_svs_l1>, + <&rpmhpd_opp_svs_l1>; + }; + + opp-444000000 { + opp-hz = /bits/ 64 <444000000>; + required-opps = <&rpmhpd_opp_turbo>, + <&rpmhpd_opp_turbo>; + }; + + opp-533333334 { + opp-hz = /bits/ 64 <533333334>; + required-opps = <&rpmhpd_opp_turbo_l1>, + <&rpmhpd_opp_turbo_l1>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/qcom,sm8650-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sm8650-camss.yaml new file mode 100644 index 000000000..9c8de7226 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sm8650-camss.yaml @@ -0,0 +1,375 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sm8650-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SM8650 Camera Subsystem (CAMSS) + +maintainers: + - Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> + +description: + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms. + +properties: + compatible: + const: qcom,sm8650-camss + + reg: + maxItems: 17 + + reg-names: + items: + - const: csid_wrapper + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid_lite0 + - const: csid_lite1 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: csiphy4 + - const: csiphy5 + - const: vfe0 + - const: vfe1 + - const: vfe2 + - const: vfe_lite0 + - const: vfe_lite1 + + clocks: + maxItems: 33 + + clock-names: + items: + - const: camnoc_axi + - const: cpas_ahb + - const: cpas_fast_ahb + - const: cpas_vfe0 + - const: cpas_vfe1 + - const: cpas_vfe2 + - const: cpas_vfe_lite + - const: csid + - const: csiphy0 + - const: csiphy0_timer + - const: csiphy1 + - const: csiphy1_timer + - const: csiphy2 + - const: csiphy2_timer + - const: csiphy3 + - const: csiphy3_timer + - const: csiphy4 + - const: csiphy4_timer + - const: csiphy5 + - const: csiphy5_timer + - const: csiphy_rx + - const: gcc_axi_hf + - const: qdss_debug_xo + - const: vfe0 + - const: vfe0_fast_ahb + - const: vfe1 + - const: vfe1_fast_ahb + - const: vfe2 + - const: vfe2_fast_ahb + - const: vfe_lite + - const: vfe_lite_ahb + - const: vfe_lite_cphy_rx + - const: vfe_lite_csid + + interrupts: + maxItems: 16 + + interrupt-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid_lite0 + - const: csid_lite1 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy3 + - const: csiphy4 + - const: csiphy5 + - const: vfe0 + - const: vfe1 + - const: vfe2 + - const: vfe_lite0 + - const: vfe_lite1 + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: ahb + - const: hf_mnoc + + iommus: + maxItems: 3 + + power-domains: + items: + - description: IFE0 GDSC - Image Front End, Global Distributed Switch Controller. + - description: IFE1 GDSC - Image Front End, Global Distributed Switch Controller. + - description: IFE2 GDSC - Image Front End, Global Distributed Switch Controller. + - description: Titan GDSC - Titan ISP Block, Global Distributed Switch Controller. + + power-domain-names: + items: + - const: ife0 + - const: ife1 + - const: ife2 + - const: top + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + patternProperties: + "^port@[0-5]$": + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + description: + Input port for receiving CSI data from a CSIPHY. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + + vdd-csiphy01-0p9-supply: + description: + Phandle to a 0.9V regulator supply to CSIPHY0 and CSIPHY1 IP blocks. + + vdd-csiphy01-1p2-supply: + description: + Phandle to a 1.2V regulator supply to CSIPHY0 and CSIPHY1 IP blocks. + + vdd-csiphy24-0p9-supply: + description: + Phandle to a 0.9V regulator supply to CSIPHY2 and CSIPHY4 IP blocks. + + vdd-csiphy24-1p2-supply: + description: + Phandle to a 1.2V regulator supply to CSIPHY2 and CSIPHY4 IP blocks. + + vdd-csiphy35-0p9-supply: + description: + Phandle to a 0.9V regulator supply to CSIPHY3 and CSIPHY5 IP blocks. + + vdd-csiphy35-1p2-supply: + description: + Phandle to a 1.2V regulator supply to CSIPHY3 and CSIPHY5 IP blocks. + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interconnects + - interconnect-names + - interrupts + - interrupt-names + - iommus + - power-domains + - power-domain-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,sm8650-camcc.h> + #include <dt-bindings/clock/qcom,sm8650-gcc.h> + #include <dt-bindings/interconnect/qcom,sm8650-rpmh.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + isp@acb6000 { + compatible = "qcom,sm8650-camss"; + reg = <0 0x0acb6000 0 0x1000>, + <0 0x0acb8000 0 0x1000>, + <0 0x0acba000 0 0x1000>, + <0 0x0acbc000 0 0x1000>, + <0 0x0accb000 0 0x1000>, + <0 0x0acd0000 0 0x1000>, + <0 0x0ace4000 0 0x2000>, + <0 0x0ace6000 0 0x2000>, + <0 0x0ace8000 0 0x2000>, + <0 0x0acea000 0 0x2000>, + <0 0x0acec000 0 0x2000>, + <0 0x0acee000 0 0x2000>, + <0 0x0ac62000 0 0xf000>, + <0 0x0ac71000 0 0xf000>, + <0 0x0ac80000 0 0xf000>, + <0 0x0accc000 0 0x2000>, + <0 0x0acd1000 0 0x2000>; + reg-names = "csid_wrapper", + "csid0", + "csid1", + "csid2", + "csid_lite0", + "csid_lite1", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "csiphy4", + "csiphy5", + "vfe0", + "vfe1", + "vfe2", + "vfe_lite0", + "vfe_lite1"; + clocks = <&camcc CAM_CC_CAMNOC_AXI_RT_CLK>, + <&camcc CAM_CC_CPAS_AHB_CLK>, + <&camcc CAM_CC_CPAS_FAST_AHB_CLK>, + <&camcc CAM_CC_CPAS_IFE_0_CLK>, + <&camcc CAM_CC_CPAS_IFE_1_CLK>, + <&camcc CAM_CC_CPAS_IFE_2_CLK>, + <&camcc CAM_CC_CPAS_IFE_LITE_CLK>, + <&camcc CAM_CC_CSID_CLK>, + <&camcc CAM_CC_CSIPHY0_CLK>, + <&camcc CAM_CC_CSI0PHYTIMER_CLK>, + <&camcc CAM_CC_CSI1PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY1_CLK>, + <&camcc CAM_CC_CSI2PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY2_CLK>, + <&camcc CAM_CC_CSI3PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY3_CLK>, + <&camcc CAM_CC_CSI4PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY4_CLK>, + <&camcc CAM_CC_CSI5PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY5_CLK>, + <&camcc CAM_CC_CSID_CSIPHY_RX_CLK>, + <&gcc GCC_CAMERA_HF_AXI_CLK>, + <&camcc CAM_CC_QDSS_DEBUG_XO_CLK>, + <&camcc CAM_CC_IFE_0_CLK>, + <&camcc CAM_CC_IFE_0_FAST_AHB_CLK>, + <&camcc CAM_CC_IFE_1_CLK>, + <&camcc CAM_CC_IFE_1_FAST_AHB_CLK>, + <&camcc CAM_CC_IFE_2_CLK>, + <&camcc CAM_CC_IFE_2_FAST_AHB_CLK>, + <&camcc CAM_CC_IFE_LITE_CLK>, + <&camcc CAM_CC_IFE_LITE_AHB_CLK>, + <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_LITE_CSID_CLK>; + clock-names = "camnoc_axi", + "cpas_ahb", + "cpas_fast_ahb", + "cpas_vfe0", + "cpas_vfe1", + "cpas_vfe2", + "cpas_vfe_lite", + "csid", + "csiphy0", + "csiphy0_timer", + "csiphy1", + "csiphy1_timer", + "csiphy2", + "csiphy2_timer", + "csiphy3", + "csiphy3_timer", + "csiphy4", + "csiphy4_timer", + "csiphy5", + "csiphy5_timer", + "csiphy_rx", + "gcc_axi_hf", + "qdss_debug_xo", + "vfe0", + "vfe0_fast_ahb", + "vfe1", + "vfe1_fast_ahb", + "vfe2", + "vfe2_fast_ahb", + "vfe_lite", + "vfe_lite_ahb", + "vfe_lite_cphy_rx", + "vfe_lite_csid"; + interrupts = <GIC_SPI 601 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 603 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 431 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 605 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 376 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 448 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 122 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 89 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 602 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 604 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 688 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 606 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 377 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "csid0", + "csid1", + "csid2", + "csid_lite0", + "csid_lite1", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "csiphy4", + "csiphy5", + "vfe0", + "vfe1", + "vfe2", + "vfe_lite0", + "vfe_lite1"; + interconnects = <&gem_noc MASTER_APPSS_PROC 0 + &config_noc SLAVE_CAMERA_CFG 0>, + <&mmss_noc MASTER_CAMNOC_HF 0 + &mc_virt SLAVE_EBI1 0>; + interconnect-names = "ahb", "hf_mnoc"; + iommus = <&apps_smmu 0x800 0x20>, + <&apps_smmu 0x18a0 0x40>, + <&apps_smmu 0x1860 0x00>; + power-domains = <&camcc CAM_CC_IFE_0_GDSC>, + <&camcc CAM_CC_IFE_1_GDSC>, + <&camcc CAM_CC_IFE_2_GDSC>, + <&camcc CAM_CC_TITAN_TOP_GDSC>; + power-domain-names = "ife0", "ife1", "ife2", "top"; + vdd-csiphy01-0p9-supply = <&vreg_0p9>; + vdd-csiphy01-1p2-supply = <&vreg_1p2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + + csiphy1_ep: endpoint { + data-lanes = <0 1>; + remote-endpoint = <&camera_sensor>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,sm8750-iris.yaml b/Documentation/devicetree/bindings/media/qcom,sm8750-iris.yaml new file mode 100644 index 000000000..c42d3470b --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,sm8750-iris.yaml @@ -0,0 +1,186 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,sm8750-iris.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SM8750 SoC Iris video encoder and decoder + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +description: + The Iris video processing unit on Qualcomm SM8750 SoC is a video encode and + decode accelerator. + +properties: + compatible: + enum: + - qcom,sm8750-iris + + clocks: + maxItems: 6 + + clock-names: + items: + - const: iface # AXI0 + - const: core + - const: vcodec0_core + - const: iface1 # AXI1 + - const: core_freerun + - const: vcodec0_core_freerun + + dma-coherent: true + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: cpu-cfg + - const: video-mem + + iommus: + maxItems: 2 + + operating-points-v2: true + opp-table: + type: object + + power-domains: + maxItems: 4 + + power-domain-names: + items: + - const: venus + - const: vcodec0 + - const: mxc + - const: mmcx + + resets: + maxItems: 4 + + reset-names: + items: + - const: bus0 + - const: bus1 + - const: core + - const: vcodec0_core + +required: + - compatible + - dma-coherent + - interconnects + - interconnect-names + - iommus + - power-domain-names + - resets + - reset-names + +allOf: + - $ref: qcom,venus-common.yaml# + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/clock/qcom,sm8750-gcc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interconnect/qcom,icc.h> + #include <dt-bindings/interconnect/qcom,sm8750-rpmh.h> + #include <dt-bindings/power/qcom-rpmpd.h> + #include <dt-bindings/power/qcom,rpmhpd.h> + + video-codec@aa00000 { + compatible = "qcom,sm8750-iris"; + reg = <0x0aa00000 0xf0000>; + + clocks = <&gcc GCC_VIDEO_AXI0_CLK>, + <&videocc_mvs0c_clk>, + <&videocc_mvs0_clk>, + <&gcc GCC_VIDEO_AXI1_CLK>, + <&videocc_mvs0c_freerun_clk>, + <&videocc_mvs0_freerun_clk>; + clock-names = "iface", + "core", + "vcodec0_core", + "iface1", + "core_freerun", + "vcodec0_core_freerun"; + + dma-coherent; + iommus = <&apps_smmu 0x1940 0>, + <&apps_smmu 0x1947 0>; + + interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY + &config_noc SLAVE_VENUS_CFG QCOM_ICC_TAG_ACTIVE_ONLY>, + <&mmss_noc MASTER_VIDEO_MVP QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "cpu-cfg", + "video-mem"; + + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + + operating-points-v2 = <&iris_opp_table>; + + memory-region = <&video_mem>; + + power-domains = <&videocc_mvs0c_gdsc>, + <&videocc_mvs0_gdsc>, + <&rpmhpd RPMHPD_MXC>, + <&rpmhpd RPMHPD_MMCX>; + power-domain-names = "venus", + "vcodec0", + "mxc", + "mmcx"; + + resets = <&gcc GCC_VIDEO_AXI0_CLK_ARES>, + <&gcc GCC_VIDEO_AXI1_CLK_ARES>, + <&videocc_mvs0c_freerun_clk_ares>, + <&videocc_mvs0_freerun_clk_ares>; + reset-names = "bus0", + "bus1", + "core", + "vcodec0_core"; + + iris_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-240000000 { + opp-hz = /bits/ 64 <240000000>; + required-opps = <&rpmhpd_opp_low_svs_d1>, + <&rpmhpd_opp_low_svs_d1>; + }; + + opp-338000000 { + opp-hz = /bits/ 64 <338000000>; + required-opps = <&rpmhpd_opp_low_svs>, + <&rpmhpd_opp_low_svs>; + }; + + opp-420000000 { + opp-hz = /bits/ 64 <420000000>; + required-opps = <&rpmhpd_opp_svs>, + <&rpmhpd_opp_svs>; + }; + + opp-444000000 { + opp-hz = /bits/ 64 <444000000>; + required-opps = <&rpmhpd_opp_svs_l1>, + <&rpmhpd_opp_svs_l1>; + }; + + opp-533333334 { + opp-hz = /bits/ 64 <533333334>; + required-opps = <&rpmhpd_opp_nom>, + <&rpmhpd_opp_nom>; + }; + + opp-630000000 { + opp-hz = /bits/ 64 <630000000>; + required-opps = <&rpmhpd_opp_turbo>, + <&rpmhpd_opp_turbo>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/qcom,venus-common.yaml b/Documentation/devicetree/bindings/media/qcom,venus-common.yaml new file mode 100644 index 000000000..59a3fde84 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,venus-common.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,venus-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SoC Venus Video Encode and Decode Accelerators Common Properties + +maintainers: + - Stanimir Varbanov <stanimir.k.varbanov@gmail.com> + - Vikash Garodia <quic_vgarodia@quicinc.com> + +description: | + The Venus IP is a video encode and decode accelerator present + on Qualcomm platforms + +properties: + reg: + maxItems: 1 + + clocks: + minItems: 3 + maxItems: 7 + + clock-names: + minItems: 3 + maxItems: 7 + + firmware-name: + maxItems: 1 + + interrupts: + maxItems: 1 + + iommus: + minItems: 1 + maxItems: 20 + + memory-region: + maxItems: 1 + + power-domains: + minItems: 1 + maxItems: 4 + + power-domain-names: + minItems: 1 + maxItems: 4 + +required: + - reg + - clocks + - clock-names + - interrupts + - memory-region + - power-domains + +additionalProperties: true diff --git a/Documentation/devicetree/bindings/media/qcom,x1e80100-camss.yaml b/Documentation/devicetree/bindings/media/qcom,x1e80100-camss.yaml new file mode 100644 index 000000000..2d1662ef5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,x1e80100-camss.yaml @@ -0,0 +1,367 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/qcom,x1e80100-camss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm X1E80100 Camera Subsystem (CAMSS) + +maintainers: + - Bryan O'Donoghue <bryan.odonoghue@linaro.org> + +description: + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms. + +properties: + compatible: + const: qcom,x1e80100-camss + + reg: + maxItems: 17 + + reg-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid_lite0 + - const: csid_lite1 + - const: csid_wrapper + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy4 + - const: csitpg0 + - const: csitpg1 + - const: csitpg2 + - const: vfe0 + - const: vfe1 + - const: vfe_lite0 + - const: vfe_lite1 + + clocks: + maxItems: 29 + + clock-names: + items: + - const: camnoc_nrt_axi + - const: camnoc_rt_axi + - const: core_ahb + - const: cpas_ahb + - const: cpas_fast_ahb + - const: cpas_vfe0 + - const: cpas_vfe1 + - const: cpas_vfe_lite + - const: cphy_rx_clk_src + - const: csid + - const: csid_csiphy_rx + - const: csiphy0 + - const: csiphy0_timer + - const: csiphy1 + - const: csiphy1_timer + - const: csiphy2 + - const: csiphy2_timer + - const: csiphy4 + - const: csiphy4_timer + - const: gcc_axi_hf + - const: gcc_axi_sf + - const: vfe0 + - const: vfe0_fast_ahb + - const: vfe1 + - const: vfe1_fast_ahb + - const: vfe_lite + - const: vfe_lite_ahb + - const: vfe_lite_cphy_rx + - const: vfe_lite_csid + + interrupts: + maxItems: 13 + + interrupt-names: + items: + - const: csid0 + - const: csid1 + - const: csid2 + - const: csid_lite0 + - const: csid_lite1 + - const: csiphy0 + - const: csiphy1 + - const: csiphy2 + - const: csiphy4 + - const: vfe0 + - const: vfe1 + - const: vfe_lite0 + - const: vfe_lite1 + + interconnects: + maxItems: 4 + + interconnect-names: + items: + - const: ahb + - const: hf_mnoc + - const: sf_mnoc + - const: sf_icp_mnoc + + iommus: + maxItems: 8 + + power-domains: + items: + - description: IFE0 GDSC - Image Front End, Global Distributed Switch Controller. + - description: IFE1 GDSC - Image Front End, Global Distributed Switch Controller. + - description: Titan Top GDSC - Titan ISP Block, Global Distributed Switch Controller. + + power-domain-names: + items: + - const: ife0 + - const: ife1 + - const: top + + vdd-csiphy-0p8-supply: + description: + 0.8V supply to a PHY. + + vdd-csiphy-1p2-supply: + description: + 1.2V supply to a PHY. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + description: + CSI input ports. + + patternProperties: + "^port@[0-3]$": + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + description: + Input port for receiving CSI data from a CSIPHY. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + required: + - data-lanes + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interrupts + - interrupt-names + - interconnects + - interconnect-names + - iommus + - power-domains + - power-domain-names + - vdd-csiphy-0p8-supply + - vdd-csiphy-1p2-supply + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,x1e80100-gcc.h> + #include <dt-bindings/clock/qcom,x1e80100-camcc.h> + #include <dt-bindings/interconnect/qcom,icc.h> + #include <dt-bindings/interconnect/qcom,x1e80100-rpmh.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + camss: isp@acb7000 { + compatible = "qcom,x1e80100-camss"; + + reg = <0 0x0acb7000 0 0x2000>, + <0 0x0acb9000 0 0x2000>, + <0 0x0acbb000 0 0x2000>, + <0 0x0acc6000 0 0x1000>, + <0 0x0acca000 0 0x1000>, + <0 0x0acb6000 0 0x1000>, + <0 0x0ace4000 0 0x1000>, + <0 0x0ace6000 0 0x1000>, + <0 0x0ace8000 0 0x1000>, + <0 0x0acec000 0 0x4000>, + <0 0x0acf6000 0 0x1000>, + <0 0x0acf7000 0 0x1000>, + <0 0x0acf8000 0 0x1000>, + <0 0x0ac62000 0 0x4000>, + <0 0x0ac71000 0 0x4000>, + <0 0x0acc7000 0 0x2000>, + <0 0x0accb000 0 0x2000>; + + reg-names = "csid0", + "csid1", + "csid2", + "csid_lite0", + "csid_lite1", + "csid_wrapper", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy4", + "csitpg0", + "csitpg1", + "csitpg2", + "vfe0", + "vfe1", + "vfe_lite0", + "vfe_lite1"; + + clocks = <&camcc CAM_CC_CAMNOC_AXI_NRT_CLK>, + <&camcc CAM_CC_CAMNOC_AXI_RT_CLK>, + <&camcc CAM_CC_CORE_AHB_CLK>, + <&camcc CAM_CC_CPAS_AHB_CLK>, + <&camcc CAM_CC_CPAS_FAST_AHB_CLK>, + <&camcc CAM_CC_CPAS_IFE_0_CLK>, + <&camcc CAM_CC_CPAS_IFE_1_CLK>, + <&camcc CAM_CC_CPAS_IFE_LITE_CLK>, + <&camcc CAM_CC_CPHY_RX_CLK_SRC>, + <&camcc CAM_CC_CSID_CLK>, + <&camcc CAM_CC_CSID_CSIPHY_RX_CLK>, + <&camcc CAM_CC_CSIPHY0_CLK>, + <&camcc CAM_CC_CSI0PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY1_CLK>, + <&camcc CAM_CC_CSI1PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY2_CLK>, + <&camcc CAM_CC_CSI2PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY4_CLK>, + <&camcc CAM_CC_CSI4PHYTIMER_CLK>, + <&gcc GCC_CAMERA_HF_AXI_CLK>, + <&gcc GCC_CAMERA_SF_AXI_CLK>, + <&camcc CAM_CC_IFE_0_CLK>, + <&camcc CAM_CC_IFE_0_FAST_AHB_CLK>, + <&camcc CAM_CC_IFE_1_CLK>, + <&camcc CAM_CC_IFE_1_FAST_AHB_CLK>, + <&camcc CAM_CC_IFE_LITE_CLK>, + <&camcc CAM_CC_IFE_LITE_AHB_CLK>, + <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_LITE_CSID_CLK>; + + clock-names = "camnoc_nrt_axi", + "camnoc_rt_axi", + "core_ahb", + "cpas_ahb", + "cpas_fast_ahb", + "cpas_vfe0", + "cpas_vfe1", + "cpas_vfe_lite", + "cphy_rx_clk_src", + "csid", + "csid_csiphy_rx", + "csiphy0", + "csiphy0_timer", + "csiphy1", + "csiphy1_timer", + "csiphy2", + "csiphy2_timer", + "csiphy4", + "csiphy4_timer", + "gcc_axi_hf", + "gcc_axi_sf", + "vfe0", + "vfe0_fast_ahb", + "vfe1", + "vfe1_fast_ahb", + "vfe_lite", + "vfe_lite_ahb", + "vfe_lite_cphy_rx", + "vfe_lite_csid"; + + interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 431 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 359 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 122 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 360 IRQ_TYPE_EDGE_RISING>; + + interrupt-names = "csid0", + "csid1", + "csid2", + "csid_lite0", + "csid_lite1", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy4", + "vfe0", + "vfe1", + "vfe_lite0", + "vfe_lite1"; + + interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY + &config_noc SLAVE_CAMERA_CFG QCOM_ICC_TAG_ACTIVE_ONLY>, + <&mmss_noc MASTER_CAMNOC_HF QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, + <&mmss_noc MASTER_CAMNOC_SF QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, + <&mmss_noc MASTER_CAMNOC_ICP QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + + interconnect-names = "ahb", + "hf_mnoc", + "sf_mnoc", + "sf_icp_mnoc"; + + iommus = <&apps_smmu 0x800 0x60>, + <&apps_smmu 0x860 0x60>, + <&apps_smmu 0x1800 0x60>, + <&apps_smmu 0x1860 0x60>, + <&apps_smmu 0x18e0 0x00>, + <&apps_smmu 0x1980 0x20>, + <&apps_smmu 0x1900 0x00>, + <&apps_smmu 0x19a0 0x20>; + + power-domains = <&camcc CAM_CC_IFE_0_GDSC>, + <&camcc CAM_CC_IFE_1_GDSC>, + <&camcc CAM_CC_TITAN_TOP_GDSC>; + + power-domain-names = "ife0", + "ife1", + "top"; + + vdd-csiphy-0p8-supply = <&csiphy_0p8_supply>; + vdd-csiphy-1p2-supply = <&csiphy_1p2_supply>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + csiphy_ep0: endpoint { + data-lanes = <0 1>; + remote-endpoint = <&sensor_ep>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/raspberrypi,pispbe.yaml b/Documentation/devicetree/bindings/media/raspberrypi,pispbe.yaml new file mode 100644 index 000000000..1fc62a1d8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/raspberrypi,pispbe.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/raspberrypi,pispbe.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Raspberry Pi PiSP Image Signal Processor (ISP) Back End + +maintainers: + - Raspberry Pi Kernel Maintenance <kernel-list@raspberrypi.com> + - Jacopo Mondi <jacopo.mondi@ideasonboard.com> + +description: | + The Raspberry Pi PiSP Image Signal Processor (ISP) Back End is an image + processor that fetches images in Bayer or Grayscale format from DRAM memory + in tiles and produces images consumable by applications. + + The full ISP documentation is available at + https://datasheets.raspberrypi.com/camera/raspberry-pi-image-signal-processor-specification.pdf + +properties: + compatible: + items: + - enum: + - brcm,bcm2712-pispbe + - const: raspberrypi,pispbe + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + iommus: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + isp@880000 { + compatible = "brcm,bcm2712-pispbe", "raspberrypi,pispbe"; + reg = <0x10 0x00880000 0x0 0x4000>; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&firmware_clocks 7>; + iommus = <&iommu2>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/raspberrypi,rp1-cfe.yaml b/Documentation/devicetree/bindings/media/raspberrypi,rp1-cfe.yaml new file mode 100644 index 000000000..eba539471 --- /dev/null +++ b/Documentation/devicetree/bindings/media/raspberrypi,rp1-cfe.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/raspberrypi,rp1-cfe.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Raspberry Pi PiSP Camera Front End + +maintainers: + - Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> + - Raspberry Pi Kernel Maintenance <kernel-list@raspberrypi.com> + +description: | + The Raspberry Pi PiSP Camera Front End is a module in Raspberrypi 5's RP1 I/O + controller, that contains: + - MIPI D-PHY + - MIPI CSI-2 receiver + - Simple image processor (called PiSP Front End, or FE) + + The FE documentation is available at: + https://datasheets.raspberrypi.com/camera/raspberry-pi-image-signal-processor-specification.pdf + + The PHY and CSI-2 receiver part have no public documentation. + +properties: + compatible: + items: + - const: raspberrypi,rp1-cfe + + reg: + items: + - description: CSI-2 registers + - description: D-PHY registers + - description: MIPI CFG (a simple top-level mux) registers + - description: FE registers + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + description: CSI-2 RX Port + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - data-lanes + +required: + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + rp1 { + #address-cells = <2>; + #size-cells = <2>; + + csi@110000 { + compatible = "raspberrypi,rp1-cfe"; + reg = <0xc0 0x40110000 0x0 0x100>, + <0xc0 0x40114000 0x0 0x100>, + <0xc0 0x40120000 0x0 0x100>, + <0xc0 0x40124000 0x0 0x1000>; + + interrupts = <42>; + + clocks = <&rp1_clocks>; + + port { + csi_ep: endpoint { + remote-endpoint = <&cam_endpoint>; + data-lanes = <1 2>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/rc.txt b/Documentation/devicetree/bindings/media/rc.txt new file mode 100644 index 000000000..be629f7fa --- /dev/null +++ b/Documentation/devicetree/bindings/media/rc.txt @@ -0,0 +1 @@ +This file has been moved to rc.yaml. diff --git a/Documentation/devicetree/bindings/media/rc.yaml b/Documentation/devicetree/bindings/media/rc.yaml new file mode 100644 index 000000000..dedc5a4b8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/rc.yaml @@ -0,0 +1,164 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/rc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Generic Infrared Remote Controller + +maintainers: + - Mauro Carvalho Chehab <mchehab@kernel.org> + - Sean Young <sean@mess.org> + +properties: + $nodename: + pattern: "^ir(-receiver)?(@[a-f0-9]+)?$" + + linux,rc-map-name: + description: + Specifies the scancode/key mapping table defined in-kernel for + the remote controller. + $ref: /schemas/types.yaml#/definitions/string + enum: + - rc-adstech-dvb-t-pci + - rc-alink-dtu-m + - rc-anysee + - rc-apac-viewcomp + - rc-astrometa-t2hybrid + - rc-asus-pc39 + - rc-asus-ps3-100 + - rc-ati-tv-wonder-hd-600 + - rc-ati-x10 + - rc-avermedia + - rc-avermedia-a16d + - rc-avermedia-cardbus + - rc-avermedia-dvbt + - rc-avermedia-m135a + - rc-avermedia-m733a-rm-k6 + - rc-avermedia-rm-ks + - rc-avertv-303 + - rc-azurewave-ad-tu700 + - rc-beelink-gs1 + - rc-beelink-mxiii + - rc-behold + - rc-behold-columbus + - rc-budget-ci-old + - rc-cec + - rc-cinergy + - rc-cinergy-1400 + - rc-ct-90405 + - rc-d680-dmb + - rc-delock-61959 + - rc-dib0700-nec + - rc-dib0700-rc5 + - rc-digitalnow-tinytwin + - rc-digittrade + - rc-dm1105-nec + - rc-dntv-live-dvb-t + - rc-dntv-live-dvbt-pro + - rc-dreambox + - rc-dtt200u + - rc-dvbsky + - rc-dvico-mce + - rc-dvico-portable + - rc-em-terratec + - rc-empty + - rc-encore-enltv + - rc-encore-enltv-fm53 + - rc-encore-enltv2 + - rc-evga-indtube + - rc-eztv + - rc-flydvb + - rc-flyvideo + - rc-fusionhdtv-mce + - rc-gadmei-rm008z + - rc-geekbox + - rc-genius-tvgo-a11mce + - rc-gotview7135 + - rc-hauppauge + - rc-hisi-poplar + - rc-hisi-tv-demo + - rc-imon-mce + - rc-imon-pad + - rc-imon-rsc + - rc-iodata-bctv7e + - rc-it913x-v1 + - rc-it913x-v2 + - rc-kaiomy + - rc-khadas + - rc-khamsin + - rc-kworld-315u + - rc-kworld-pc150u + - rc-kworld-plus-tv-analog + - rc-leadtek-y04g0051 + - rc-lme2510 + - rc-manli + - rc-mecool-kii-pro + - rc-mecool-kiii-pro + - rc-medion-x10 + - rc-medion-x10-digitainer + - rc-medion-x10-or2x + - rc-minix-neo + - rc-msi-digivox-ii + - rc-msi-digivox-iii + - rc-msi-tvanywhere + - rc-msi-tvanywhere-plus + - rc-mygica-utv3 + - rc-nebula + - rc-nec-terratec-cinergy-xs + - rc-norwood + - rc-npgtech + - rc-odroid + - rc-pctv-sedna + - rc-pine64 + - rc-pinnacle-color + - rc-pinnacle-grey + - rc-pinnacle-pctv-hd + - rc-pixelview + - rc-pixelview-002t + - rc-pixelview-mk12 + - rc-pixelview-new + - rc-powercolor-real-angel + - rc-proteus-2309 + - rc-purpletv + - rc-pv951 + - rc-rc5-tv + - rc-rc6-mce + - rc-real-audio-220-32-keys + - rc-reddo + - rc-snapstream-firefly + - rc-streamzap + - rc-su3000 + - rc-tanix-tx3mini + - rc-tanix-tx5max + - rc-tbs-nec + - rc-technisat-ts35 + - rc-technisat-usb2 + - rc-terratec-cinergy-c-pci + - rc-terratec-cinergy-s2-hd + - rc-terratec-cinergy-xs + - rc-terratec-slim + - rc-terratec-slim-2 + - rc-tevii-nec + - rc-tivo + - rc-total-media-in-hand + - rc-total-media-in-hand-02 + - rc-trekstor + - rc-tt-1500 + - rc-twinhan-dtv-cab-ci + - rc-twinhan1027 + - rc-videomate-k100 + - rc-videomate-s350 + - rc-videomate-tv-pvr + - rc-videostrong-kii-pro + - rc-vega-s9x + - rc-wetek-hub + - rc-wetek-play2 + - rc-winfast + - rc-winfast-usbii-deluxe + - rc-x96max + - rc-xbox-360 + - rc-xbox-dvd + - rc-zx-irdec + +additionalProperties: true diff --git a/Documentation/devicetree/bindings/media/renesas,ceu.yaml b/Documentation/devicetree/bindings/media/renesas,ceu.yaml new file mode 100644 index 000000000..d527fc42c --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,ceu.yaml @@ -0,0 +1,82 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,ceu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas Capture Engine Unit (CEU) + +maintainers: + - Jacopo Mondi <jacopo+renesas@jmondi.org> + - linux-renesas-soc@vger.kernel.org + +description: |+ + The Capture Engine Unit is the image capture interface found in the Renesas SH + Mobile, R-Mobile and RZ SoCs. The interface supports a single parallel input + with data bus width of 8 or 16 bits. + +properties: + compatible: + enum: + - renesas,r7s72100-ceu + - renesas,r8a7740-ceu + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + hsync-active: true + vsync-active: true + field-even-active: false + bus-width: + enum: [8, 16] + default: 8 + +required: + - compatible + - reg + - interrupts + - clocks + - power-domains + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/r7s72100-clock.h> + + ceu: ceu@e8210000 { + reg = <0xe8210000 0x209c>; + compatible = "renesas,r7s72100-ceu"; + interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp6_clks R7S72100_CLK_CEU>; + power-domains = <&cpg_clocks>; + + port { + ceu_in: endpoint { + remote-endpoint = <&ov7670_out>; + hsync-active = <1>; + vsync-active = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,csi2.yaml b/Documentation/devicetree/bindings/media/renesas,csi2.yaml new file mode 100644 index 000000000..80b778758 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,csi2.yaml @@ -0,0 +1,170 @@ +# SPDX-License-Identifier: GPL-2.0-only +# Copyright (C) 2020 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,csi2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car MIPI CSI-2 receiver + +maintainers: + - Niklas Söderlund <niklas.soderlund@ragnatech.se> + +description: + The R-Car CSI-2 receiver device provides MIPI CSI-2 capabilities for the + Renesas R-Car and RZ/G2 family of devices. It is used in conjunction with the + R-Car VIN module, which provides the video capture capabilities. + +properties: + compatible: + items: + - enum: + - renesas,r8a774a1-csi2 # RZ/G2M + - renesas,r8a774b1-csi2 # RZ/G2N + - renesas,r8a774c0-csi2 # RZ/G2E + - renesas,r8a774e1-csi2 # RZ/G2H + - renesas,r8a7795-csi2 # R-Car H3 + - renesas,r8a7796-csi2 # R-Car M3-W + - renesas,r8a77961-csi2 # R-Car M3-W+ + - renesas,r8a77965-csi2 # R-Car M3-N + - renesas,r8a77970-csi2 # R-Car V3M + - renesas,r8a77980-csi2 # R-Car V3H + - renesas,r8a77990-csi2 # R-Car E3 + - renesas,r8a779a0-csi2 # R-Car V3U + - renesas,r8a779g0-csi2 # R-Car V4H + - renesas,r8a779h0-csi2 # R-Car V4M + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + items: + maximum: 4 + + required: + - clock-lanes + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Output port node, multiple endpoints describing all the R-Car VIN + modules connected the CSI-2 receiver. + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - interrupts + - clocks + - power-domains + - resets + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a7796-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7796-sysc.h> + + csi20: csi2@fea80000 { + compatible = "renesas,r8a7796-csi2"; + reg = <0xfea80000 0x10000>; + interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 714>; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 714>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + csi20_in: endpoint { + clock-lanes = <0>; + data-lanes = <1>; + remote-endpoint = <&adv7482_txb>; + }; + }; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + csi20vin0: endpoint@0 { + reg = <0>; + remote-endpoint = <&vin0csi20>; + }; + csi20vin1: endpoint@1 { + reg = <1>; + remote-endpoint = <&vin1csi20>; + }; + csi20vin2: endpoint@2 { + reg = <2>; + remote-endpoint = <&vin2csi20>; + }; + csi20vin3: endpoint@3 { + reg = <3>; + remote-endpoint = <&vin3csi20>; + }; + csi20vin4: endpoint@4 { + reg = <4>; + remote-endpoint = <&vin4csi20>; + }; + csi20vin5: endpoint@5 { + reg = <5>; + remote-endpoint = <&vin5csi20>; + }; + csi20vin6: endpoint@6 { + reg = <6>; + remote-endpoint = <&vin6csi20>; + }; + csi20vin7: endpoint@7 { + reg = <7>; + remote-endpoint = <&vin7csi20>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,drif.yaml b/Documentation/devicetree/bindings/media/renesas,drif.yaml new file mode 100644 index 000000000..9403b235e --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,drif.yaml @@ -0,0 +1,269 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,drif.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car Gen3 Digital Radio Interface Controller (DRIF) + +maintainers: + - Ramesh Shanmugasundaram <rashanmu@gmail.com> + - Fabrizio Castro <fabrizio.castro.jz@renesas.com> + +description: | + R-Car Gen3 DRIF is a SPI like receive only slave device. A general + representation of DRIF interfacing with a master device is shown below. + + +---------------------+ +---------------------+ + | |-----SCK------->|CLK | + | Master |-----SS-------->|SYNC DRIFn (slave) | + | |-----SD0------->|D0 | + | |-----SD1------->|D1 | + +---------------------+ +---------------------+ + + As per datasheet, each DRIF channel (drifn) is made up of two internal + channels (drifn0 & drifn1). These two internal channels share the common + CLK & SYNC. Each internal channel has its own dedicated resources like + irq, dma channels, address space & clock. This internal split is not + visible to the external master device. + + The device tree model represents each internal channel as a separate node. + The internal channels sharing the CLK & SYNC are tied together by their + phandles using a property called "renesas,bonding". For the rest of + the documentation, unless explicitly stated, the word channel implies an + internal channel. + + When both internal channels are enabled they need to be managed together + as one (i.e.) they cannot operate alone as independent devices. Out of the + two, one of them needs to act as a primary device that accepts common + properties of both the internal channels. This channel is identified by a + property called "renesas,primary-bond". + + To summarize, + * When both the internal channels that are bonded together are enabled, + the zeroth channel is selected as primary-bond. This channels accepts + properties common to all the members of the bond. + * When only one of the bonded channels need to be enabled, the property + "renesas,bonding" or "renesas,primary-bond" will have no effect. That + enabled channel can act alone as any other independent device. + +properties: + compatible: + items: + - enum: + - renesas,r8a7795-drif # R-Car H3 + - renesas,r8a7796-drif # R-Car M3-W + - renesas,r8a77965-drif # R-Car M3-N + - renesas,r8a77990-drif # R-Car E3 + - const: renesas,rcar-gen3-drif # Generic R-Car Gen3 compatible device + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: fck + + resets: + maxItems: 1 + + dmas: + minItems: 1 + maxItems: 2 + + dma-names: + minItems: 1 + items: + - const: rx + - const: rx + + renesas,bonding: + $ref: /schemas/types.yaml#/definitions/phandle + description: + The phandle to the other internal channel of DRIF + + power-domains: + maxItems: 1 + + renesas,primary-bond: + type: boolean + description: + Indicates that the channel acts as primary among the bonded channels. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Child port node corresponding to the data input. The port node must + contain at least one endpoint. + + properties: + endpoint: + $ref: /schemas/graph.yaml#/$defs/endpoint-base + unevaluatedProperties: false + + properties: + sync-active: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: + Indicates sync signal polarity, 0/1 for low/high respectively. + This property maps to SYNCAC bit in the hardware manual. The + default is 1 (active high). + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + - dmas + - dma-names + - renesas,bonding + - power-domains + +allOf: + - if: + required: + - renesas,primary-bond + then: + required: + - pinctrl-0 + - pinctrl-names + - port + + - if: + required: + - port + then: + required: + - pinctrl-0 + - pinctrl-names + else: + properties: + pinctrl-0: false + pinctrl-names: false + +additionalProperties: false + +examples: + # Example with both internal channels enabled. + # + # When interfacing with a third party tuner device with two data pins as shown + # below. + # + # +---------------------+ +---------------------+ + # | |-----SCK------->|CLK | + # | Master |-----SS-------->|SYNC DRIFn (slave) | + # | |-----SD0------->|D0 | + # | |-----SD1------->|D1 | + # +---------------------+ +---------------------+ + - | + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7795-sysc.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + drif00: rif@e6f40000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f40000 0 0x64>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 515>; + clock-names = "fck"; + dmas = <&dmac1 0x20>, <&dmac2 0x20>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + renesas,bonding = <&drif01>; + resets = <&cpg 515>; + renesas,primary-bond; + pinctrl-0 = <&drif0_pins>; + pinctrl-names = "default"; + port { + drif0_ep: endpoint { + remote-endpoint = <&tuner_ep>; + }; + }; + }; + + drif01: rif@e6f50000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f50000 0 0x64>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 514>; + clock-names = "fck"; + dmas = <&dmac1 0x22>, <&dmac2 0x22>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + renesas,bonding = <&drif00>; + resets = <&cpg 514>; + }; + }; + + # Example with internal channel 1 alone enabled. + # + # When interfacing with a third party tuner device with one data pin as shown + # below. + # + # +---------------------+ +---------------------+ + # | |-----SCK------->|CLK | + # | Master |-----SS-------->|SYNC DRIFn (slave) | + # | | |D0 (unused) | + # | |-----SD-------->|D1 | + # +---------------------+ +---------------------+ + - | + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7795-sysc.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + drif10: rif@e6f60000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f60000 0 0x64>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 513>; + clock-names = "fck"; + dmas = <&dmac1 0x24>, <&dmac2 0x24>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 513>; + renesas,bonding = <&drif11>; + }; + + drif11: rif@e6f70000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f70000 0 0x64>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 512>; + clock-names = "fck"; + dmas = <&dmac1 0x26>, <&dmac2 0x26>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 512>; + renesas,bonding = <&drif10>; + pinctrl-0 = <&drif1_pins>; + pinctrl-names = "default"; + port { + drif1_ep: endpoint { + remote-endpoint = <&tuner_ep1>; + sync-active = <0>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.yaml b/Documentation/devicetree/bindings/media/renesas,fcp.yaml new file mode 100644 index 000000000..5e11ae0ee --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,fcp.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,fcp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car Frame Compression Processor (FCP) + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: | + The FCP is a companion module of video processing modules in the Renesas + R-Car Gen3 and RZ/G2 SoCs. It provides data compression and decompression, + data caching, and conversion of AXI transactions in order to reduce the + memory bandwidth. + + There are three types of FCP: FCP for Codec (FCPC), FCP for VSP (FCPV) and + FCP for FDP (FCPF). Their configuration and behaviour depend on the module + they are paired with. These DT bindings currently support the FCPV and FCPF. + +properties: + compatible: + oneOf: + - enum: + - renesas,fcpv # FCP for VSP + - renesas,fcpf # FCP for FDP + - items: + - enum: + - renesas,r9a07g043u-fcpvd # RZ/G2UL + - renesas,r9a07g044-fcpvd # RZ/G2{L,LC} + - renesas,r9a07g054-fcpvd # RZ/V2L + - renesas,r9a08g046-fcpvd # RZ/G3L + - renesas,r9a09g047-fcpvd # RZ/G3E + - renesas,r9a09g056-fcpvd # RZ/V2N + - renesas,r9a09g057-fcpvd # RZ/V2H(P) + - const: renesas,fcpv # Generic FCP for VSP fallback + + reg: + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: Main clock + - description: Register access clock + - description: Video clock + + clock-names: + items: + - const: aclk + - const: pclk + - const: vclk + + iommus: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - power-domains + - resets + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + enum: + - renesas,r9a07g043u-fcpvd + - renesas,r9a07g044-fcpvd + - renesas,r9a07g054-fcpvd + - renesas,r9a08g046-fcpvd + - renesas,r9a09g047-fcpvd + - renesas,r9a09g056-fcpvd + - renesas,r9a09g057-fcpvd + then: + properties: + clocks: + minItems: 3 + required: + - clock-names + else: + properties: + clocks: + maxItems: 1 + clock-names: false + +examples: + # R8A7795 (R-Car H3) FCP for VSP-D1 + - | + #include <dt-bindings/clock/renesas-cpg-mssr.h> + #include <dt-bindings/power/r8a7795-sysc.h> + + fcp@fea2f000 { + compatible = "renesas,fcpv"; + reg = <0xfea2f000 0x200>; + clocks = <&cpg CPG_MOD 602>; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 602>; + iommus = <&ipmmu_vi0 9>; + }; +... diff --git a/Documentation/devicetree/bindings/media/renesas,fdp1.yaml b/Documentation/devicetree/bindings/media/renesas,fdp1.yaml new file mode 100644 index 000000000..2a27a7296 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,fdp1.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,fdp1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car Fine Display Processor (FDP1) + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: + The FDP1 is a de-interlacing module which converts interlaced video to + progressive video. It is capable of performing pixel format conversion + between YCbCr/YUV formats and RGB formats. Only YCbCr/YUV formats are + supported as an input to the module. + +properties: + compatible: + enum: + - renesas,fdp1 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + renesas,fcp: + $ref: /schemas/types.yaml#/definitions/phandle + description: + A phandle referencing the FCP that handles memory accesses for the FDP1. + Not allowed on R-Car Gen2, mandatory on R-Car Gen3. + +required: + - compatible + - reg + - interrupts + - clocks + - power-domains + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/renesas-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7795-sysc.h> + + fdp1@fe940000 { + compatible = "renesas,fdp1"; + reg = <0xfe940000 0x2400>; + interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 119>; + power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 119>; + renesas,fcp = <&fcpf0>; + }; +... diff --git a/Documentation/devicetree/bindings/media/renesas,imr.yaml b/Documentation/devicetree/bindings/media/renesas,imr.yaml new file mode 100644 index 000000000..512f57417 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,imr.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,imr.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car Image Renderer (Distortion Correction Engine) + +maintainers: + - Sergei Shtylyov <sergei.shtylyov@gmail.com> + +description: | + The image renderer, or the distortion correction engine, is a drawing + processor with a simple instruction system capable of referencing video + capture data or data in an external memory as 2D texture data and performing + texture mapping and drawing with respect to any shape that is split into + triangular objects. + + The image renderer light extended 4 (IMR-LX4) is found in R-Car Gen3 SoCs. + +properties: + compatible: + items: + - enum: + - renesas,r8a7795-imr-lx4 # R-Car H3 + - renesas,r8a7796-imr-lx4 # R-Car M3-W + - const: renesas,imr-lx4 # R-Car Gen3 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - power-domains + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7795-sysc.h> + + imr-lx4@fe860000 { + compatible = "renesas,r8a7795-imr-lx4", "renesas,imr-lx4"; + reg = <0xfe860000 0x2000>; + interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 823>; + power-domains = <&sysc R8A7795_PD_A3VC>; + resets = <&cpg 823>; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,isp.yaml b/Documentation/devicetree/bindings/media/renesas,isp.yaml new file mode 100644 index 000000000..d25e020f5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,isp.yaml @@ -0,0 +1,246 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +# Copyright (C) 2021 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,isp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car ISP Channel Selector + +maintainers: + - Niklas Söderlund <niklas.soderlund@ragnatech.se> + +description: + The R-Car ISP Channel Selector provides MIPI CSI-2 VC and DT filtering + capabilities for the Renesas R-Car family of devices. It is used in + conjunction with the R-Car VIN and CSI-2 modules, which provides the video + capture capabilities. + +properties: + compatible: + items: + - enum: + - renesas,r8a779a0-isp # V3U + - renesas,r8a779g0-isp # V4H + - renesas,r8a779h0-isp # V4M + - const: renesas,rcar-gen4-isp # Generic R-Car Gen4 + reg: + minItems: 1 + maxItems: 2 + + reg-names: + minItems: 1 + items: + - const: cs + - const: core + + interrupts: + minItems: 1 + maxItems: 2 + + interrupt-names: + minItems: 1 + items: + - const: cs + - const: core + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: cs + - const: core + + power-domains: + maxItems: 1 + + resets: + minItems: 1 + maxItems: 2 + + reset-names: + minItems: 1 + items: + - const: cs + - const: core + + renesas,vspx: + $ref: /schemas/types.yaml#/definitions/phandle + description: + A phandle to the companion VSPX responsible for the Streaming Bridge + functionality. The Streaming Bridge is responsible for feeding image + and configuration data to the ISP when operating in memory-to-memory + mode. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: + Input port node, multiple endpoints describing the connected R-Car + CSI-2 receivers. + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 0. + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 1. + + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 2. + + port@4: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 3. + + port@5: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 4. + + port@6: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 5. + + port@7: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 6. + + port@8: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 7. + + required: + - port@0 + - port@1 + - port@2 + - port@3 + - port@4 + - port@5 + - port@6 + - port@7 + - port@8 + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-names + - clocks + - clock-names + - power-domains + - resets + - reset-names + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a779a0-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a779a0-sysc.h> + + isp1: isp@fed20000 { + compatible = "renesas,r8a779a0-isp", "renesas,rcar-gen4-isp"; + reg = <0xfed20000 0x10000>, <0xfee00000 0x100000>; + reg-names = "cs", "core"; + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cs", "core"; + clocks = <&cpg CPG_MOD 613>, <&cpg CPG_MOD 17>; + clock-names = "cs", "core"; + power-domains = <&sysc R8A779A0_PD_A3ISP01>; + resets = <&cpg 613>, <&cpg 17>; + reset-names = "cs", "core"; + + renesas,vspx = <&vspx1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0>; + isp1csi41: endpoint@1 { + reg = <1>; + remote-endpoint = <&csi41isp1>; + }; + }; + + port@1 { + reg = <1>; + isp1vin08: endpoint { + remote-endpoint = <&vin08isp1>; + }; + }; + + port@2 { + reg = <2>; + isp1vin09: endpoint { + remote-endpoint = <&vin09isp1>; + }; + }; + + port@3 { + reg = <3>; + isp1vin10: endpoint { + remote-endpoint = <&vin10isp1>; + }; + }; + + port@4 { + reg = <4>; + isp1vin11: endpoint { + remote-endpoint = <&vin11isp1>; + }; + }; + + port@5 { + reg = <5>; + isp1vin12: endpoint { + remote-endpoint = <&vin12isp1>; + }; + }; + + port@6 { + reg = <6>; + isp1vin13: endpoint { + remote-endpoint = <&vin13isp1>; + }; + }; + + port@7 { + reg = <7>; + isp1vin14: endpoint { + remote-endpoint = <&vin14isp1>; + }; + }; + + port@8 { + reg = <8>; + isp1vin15: endpoint { + remote-endpoint = <&vin15isp1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,jpu.yaml b/Documentation/devicetree/bindings/media/renesas,jpu.yaml new file mode 100644 index 000000000..2f55968e8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,jpu.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,jpu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas JPEG Processing Unit + +maintainers: + - Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com> + +description: + The JPEG processing unit (JPU) incorporates the JPEG codec with an encoding + and decoding function conforming to the JPEG baseline process, so that the + JPU can encode image data and decode JPEG data quickly. + +properties: + compatible: + items: + - enum: + - renesas,jpu-r8a7790 # R-Car H2 + - renesas,jpu-r8a7791 # R-Car M2-W + - renesas,jpu-r8a7792 # R-Car V2H + - renesas,jpu-r8a7793 # R-Car M2-N + - const: renesas,rcar-gen2-jpu # R-Car Gen2 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - power-domains + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a7790-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7790-sysc.h> + + jpeg-codec@fe980000 { + compatible = "renesas,jpu-r8a7790", "renesas,rcar-gen2-jpu"; + reg = <0xfe980000 0x10300>; + interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 106>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 106>; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,r9a09g057-ivc.yaml b/Documentation/devicetree/bindings/media/renesas,r9a09g057-ivc.yaml new file mode 100644 index 000000000..c09cbd8c9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,r9a09g057-ivc.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,r9a09g057-ivc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas RZ/V2H(P) Input Video Control Block + +maintainers: + - Daniel Scally <dan.scally@ideasonboard.com> + +description: + The IVC block is a module that takes video frames from memory and feeds them + to the Image Signal Processor for processing. + +properties: + compatible: + const: renesas,r9a09g057-ivc # RZ/V2H(P) + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Input Video Control block register access clock + - description: Video input data AXI bus clock + - description: ISP system clock + + clock-names: + items: + - const: reg + - const: axi + - const: isp + + power-domains: + maxItems: 1 + + resets: + items: + - description: Input Video Control block register access reset + - description: Video input data AXI bus reset + - description: ISP core reset + + reset-names: + items: + - const: reg + - const: axi + - const: isp + + port: + $ref: /schemas/graph.yaml#/properties/port + description: Output parallel video bus + + properties: + endpoint: + $ref: /schemas/graph.yaml#/properties/endpoint + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + - resets + - reset-names + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/renesas,r9a09g057-cpg.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + isp-input@16040000 { + compatible = "renesas,r9a09g057-ivc"; + reg = <0x16040000 0x230>; + + clocks = <&cpg CPG_MOD 0xe3>, + <&cpg CPG_MOD 0xe4>, + <&cpg CPG_MOD 0xe5>; + clock-names = "reg", "axi", "isp"; + + power-domains = <&cpg>; + + resets = <&cpg 0xd4>, + <&cpg 0xd1>, + <&cpg 0xd3>; + reset-names = "reg", "axi", "isp"; + + interrupts = <GIC_SPI 861 IRQ_TYPE_EDGE_RISING>; + + port { + ivc_out: endpoint { + remote-endpoint = <&isp_in>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/renesas,rzg2l-cru.yaml b/Documentation/devicetree/bindings/media/renesas,rzg2l-cru.yaml new file mode 100644 index 000000000..47e18690f --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,rzg2l-cru.yaml @@ -0,0 +1,227 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (C) 2022 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,rzg2l-cru.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas RZ/G2L (and alike SoC's) Camera Data Receiving Unit (CRU) Image processing + +maintainers: + - Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> + +description: + The CRU image processing module is a data conversion module equipped with pixel + color space conversion, LUT, pixel format conversion, etc. An MIPI CSI-2 input and + parallel (including ITU-R BT.656) input are provided as the image sensor interface. + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,r9a07g043-cru # RZ/G2UL + - renesas,r9a07g044-cru # RZ/G2{L,LC} + - renesas,r9a07g054-cru # RZ/V2L + - const: renesas,rzg2l-cru + - const: renesas,r9a09g047-cru # RZ/G3E + + reg: + maxItems: 1 + + interrupts: + oneOf: + - items: + - description: CRU Interrupt for image_conv + - description: CRU Interrupt for image_conv_err + - description: CRU AXI master error interrupt + - items: + - description: CRU Interrupt for image_conv + - description: CRU AXI master error interrupt + - description: CRU Video Data AXI Master Address 0 Write End interrupt + - description: CRU Statistics data AXI master addr 0 write end interrupt + - description: CRU Video statistics data AXI master addr 0 write end interrupt + + interrupt-names: + oneOf: + - items: + - const: image_conv + - const: image_conv_err + - const: axi_mst_err + - items: + - const: image_conv + - const: axi_mst_err + - const: vd_addr_wend + - const: sd_addr_wend + - const: vsd_addr_wend + + clocks: + items: + - description: CRU Main clock + - description: CRU Register access clock + - description: CRU image transfer clock + + clock-names: + items: + - const: video + - const: apb + - const: axi + + power-domains: + maxItems: 1 + + resets: + items: + - description: CRU_PRESETN reset terminal + - description: CRU_ARESETN reset terminal + + reset-names: + items: + - const: presetn + - const: aresetn + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port node, single endpoint describing a parallel input source. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + hsync-active: true + vsync-active: true + bus-width: true + data-shift: true + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Input port node, describing the Image Processing module connected to the + CSI-2 receiver. + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + - clock-names + - resets + - reset-names + - power-domains + +allOf: + - if: + properties: + compatible: + contains: + enum: + - renesas,r9a07g044-cru + - renesas,r9a07g054-cru + then: + properties: + interrupts: + maxItems: 3 + interrupt-names: + maxItems: 3 + ports: + required: + - port@0 + - port@1 + + - if: + properties: + compatible: + contains: + enum: + - renesas,r9a07g043-cru + then: + properties: + interrupts: + maxItems: 3 + interrupt-names: + maxItems: 3 + ports: + properties: + port@0: false + required: + - port@1 + + - if: + properties: + compatible: + contains: + const: renesas,r9a09g047-cru + then: + properties: + interrupts: + minItems: 5 + interrupt-names: + minItems: 5 + ports: + properties: + port@0: false + required: + - port@1 + +additionalProperties: false + +examples: + # Device node example with CSI-2 + - | + #include <dt-bindings/clock/r9a07g044-cpg.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + cru: video@10830000 { + compatible = "renesas,r9a07g044-cru", "renesas,rzg2l-cru"; + reg = <0x10830000 0x400>; + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "image_conv", "image_conv_err", "axi_mst_err"; + clocks = <&cpg CPG_MOD R9A07G044_CRU_VCLK>, + <&cpg CPG_MOD R9A07G044_CRU_PCLK>, + <&cpg CPG_MOD R9A07G044_CRU_ACLK>; + clock-names = "video", "apb", "axi"; + power-domains = <&cpg>; + resets = <&cpg R9A07G044_CRU_PRESETN>, + <&cpg R9A07G044_CRU_ARESETN>; + reset-names = "presetn", "aresetn"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + cru_parallel_in: endpoint@0 { + reg = <0>; + remote-endpoint = <&ov5642>; + hsync-active = <1>; + vsync-active = <1>; + }; + }; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + cru_csi_in: endpoint@0 { + reg = <0>; + remote-endpoint = <&csi_cru_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,rzg2l-csi2.yaml b/Documentation/devicetree/bindings/media/renesas,rzg2l-csi2.yaml new file mode 100644 index 000000000..c5c511c9f --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,rzg2l-csi2.yaml @@ -0,0 +1,182 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (C) 2022 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,rzg2l-csi2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas RZ/G2L (and alike SoC's) MIPI CSI-2 receiver + +maintainers: + - Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> + +description: + The CSI-2 receiver device provides MIPI CSI-2 capabilities for the Renesas RZ/G2L + (and alike SoCs). MIPI CSI-2 is part of the CRU block which is used in conjunction + with the Image Processing module, which provides the video capture capabilities. + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,r9a07g043-csi2 # RZ/G2UL + - renesas,r9a07g044-csi2 # RZ/G2{L,LC} + - renesas,r9a07g054-csi2 # RZ/V2L + - const: renesas,rzg2l-csi2 + - items: + - const: renesas,r9a09g047-csi2 # RZ/G3E + - const: renesas,r9a09g057-csi2 + - const: renesas,r9a09g057-csi2 # RZ/V2H(P) + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + oneOf: + - items: + - description: Internal clock for connecting CRU and MIPI + - description: CRU Main clock + - description: CRU Register access clock + - items: + - description: CRU Main clock + - description: CRU Register access clock + + clock-names: + oneOf: + - items: + - const: system + - const: video + - const: apb + - items: + - const: video + - const: apb + + power-domains: + maxItems: 1 + + resets: + items: + - description: CRU_PRESETN reset terminal + - description: D-PHY reset (CRU_CMN_RSTB or CRU_n_S_RESETN) + + reset-names: + items: + - const: presetn + - const: cmn-rstb + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + items: + maximum: 4 + + required: + - clock-lanes + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Output port node, Image Processing block connected to the CSI-2 receiver. + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + - resets + - reset-names + - ports + +allOf: + - if: + properties: + compatible: + contains: + const: renesas,r9a09g057-csi2 + then: + properties: + clocks: + maxItems: 2 + clock-names: + maxItems: 2 + else: + properties: + clocks: + minItems: 3 + clock-names: + minItems: 3 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r9a07g044-cpg.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + csi: csi@10830400 { + compatible = "renesas,r9a07g044-csi2", "renesas,rzg2l-csi2"; + reg = <0x10830400 0xfc00>; + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD R9A07G044_CRU_SYSCLK>, + <&cpg CPG_MOD R9A07G044_CRU_VCLK>, + <&cpg CPG_MOD R9A07G044_CRU_PCLK>; + clock-names = "system", "video", "apb"; + power-domains = <&cpg>; + resets = <&cpg R9A07G044_CRU_PRESETN>, + <&cpg R9A07G044_CRU_CMN_RSTB>; + reset-names = "presetn", "cmn-rstb"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + csi2_in: endpoint { + clock-lanes = <0>; + data-lanes = <1 2>; + remote-endpoint = <&ov5645_ep>; + }; + }; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + csi2cru: endpoint@0 { + reg = <0>; + remote-endpoint = <&crucsi2>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,vin.yaml b/Documentation/devicetree/bindings/media/renesas,vin.yaml new file mode 100644 index 000000000..cf54176f4 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,vin.yaml @@ -0,0 +1,361 @@ +# SPDX-License-Identifier: GPL-2.0-only +# Copyright (C) 2020 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,vin.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car Video Input (VIN) + +maintainers: + - Niklas Söderlund <niklas.soderlund@ragnatech.se> + +description: + The R-Car Video Input (VIN) device provides video input capabilities for the + Renesas R-Car family of devices. + + Each VIN instance has a single parallel input that supports RGB and YUV video, + with both external synchronization and BT.656 synchronization for the latter. + Depending on the instance the VIN input is connected to external SoC pins, or + on Gen3 and RZ/G2 platforms to a CSI-2 receiver. + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,vin-r8a7742 # RZ/G1H + - renesas,vin-r8a7743 # RZ/G1M + - renesas,vin-r8a7744 # RZ/G1N + - renesas,vin-r8a7745 # RZ/G1E + - renesas,vin-r8a77470 # RZ/G1C + - renesas,vin-r8a7790 # R-Car H2 + - renesas,vin-r8a7791 # R-Car M2-W + - renesas,vin-r8a7792 # R-Car V2H + - renesas,vin-r8a7793 # R-Car M2-N + - renesas,vin-r8a7794 # R-Car E2 + - const: renesas,rcar-gen2-vin # Generic R-Car Gen2 or RZ/G1 + + - items: + - enum: + - renesas,vin-r8a774a1 # RZ/G2M + - renesas,vin-r8a774b1 # RZ/G2N + - renesas,vin-r8a774c0 # RZ/G2E + - renesas,vin-r8a774e1 # RZ/G2H + - renesas,vin-r8a7778 # R-Car M1 + - renesas,vin-r8a7779 # R-Car H1 + - renesas,vin-r8a7795 # R-Car H3 + - renesas,vin-r8a7796 # R-Car M3-W + - renesas,vin-r8a77961 # R-Car M3-W+ + - renesas,vin-r8a77965 # R-Car M3-N + - renesas,vin-r8a77970 # R-Car V3M + - renesas,vin-r8a77980 # R-Car V3H + - renesas,vin-r8a77990 # R-Car E3 + - renesas,vin-r8a77995 # R-Car D3 + - items: + - enum: + - renesas,vin-r8a779a0 # R-Car V3U + - renesas,vin-r8a779g0 # R-Car V4H + - renesas,vin-r8a779h0 # R-Car V4M + - const: renesas,rcar-gen4-vin # Generic R-Car Gen4 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + # The per-board settings for Gen2 and RZ/G1 platforms: + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + A node containing a parallel input + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + hsync-active: + description: + If both HSYNC and VSYNC polarities are not specified, embedded + synchronization is selected. + default: 1 + + vsync-active: + description: + If both HSYNC and VSYNC polarities are not specified, embedded + synchronization is selected. + default: 1 + + field-even-active: true + + bus-width: true + + data-shift: true + + data-enable-active: + description: Polarity of CLKENB signal + default: 1 + + pclk-sample: true + + data-active: true + + # The per-board settings for Gen3 and RZ/G2 platforms: + renesas,id: + description: VIN channel number + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port node, single endpoint describing a parallel input source. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + hsync-active: + description: + If both HSYNC and VSYNC polarities are not specified, embedded + synchronization is selected. + default: 1 + + vsync-active: + description: + If both HSYNC and VSYNC polarities are not specified, embedded + synchronization is selected. + default: 1 + + field-even-active: true + + bus-width: true + + data-shift: true + + data-enable-active: + description: Polarity of CLKENB signal + default: 1 + + pclk-sample: true + + data-active: true + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Input port node, multiple endpoints describing all the R-Car CSI-2 + modules connected the VIN. + + properties: + endpoint@0: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Endpoint connected to CSI20. + + endpoint@1: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Endpoint connected to CSI21. + + endpoint@2: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Endpoint connected to CSI40. + + endpoint@3: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Endpoint connected to CSI41. + + anyOf: + - required: + - endpoint@0 + - required: + - endpoint@1 + - required: + - endpoint@2 + - required: + - endpoint@3 + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: + Input port node, multiple endpoints describing all the R-Car ISP + modules connected the VIN. + + properties: + endpoint@0: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Endpoint connected to ISP0. + + endpoint@1: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Endpoint connected to ISP1. + + endpoint@2: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Endpoint connected to ISP2. + + endpoint@3: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Endpoint connected to ISP3. + +required: + - compatible + - reg + - interrupts + - clocks + - power-domains + +allOf: + - if: + not: + properties: + compatible: + contains: + enum: + - renesas,vin-r8a7778 + - renesas,vin-r8a7779 + then: + required: + - resets + + - if: + properties: + compatible: + contains: + enum: + - renesas,vin-r8a7778 + - renesas,vin-r8a7779 + - renesas,rcar-gen2-vin + then: + required: + - port + else: + required: + - renesas,id + - ports + +additionalProperties: false + +examples: + # Device node example for Gen2 platform + - | + #include <dt-bindings/clock/r8a7790-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7790-sysc.h> + + vin1: vin@e6ef1000 { + compatible = "renesas,vin-r8a7790", + "renesas,rcar-gen2-vin"; + reg = <0xe6ef1000 0x1000>; + interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 810>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 810>; + + port { + vin1ep0: endpoint { + remote-endpoint = <&adv7180>; + bus-width = <8>; + }; + }; + }; + + # Device node example for Gen3 platform with only CSI-2 + - | + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7795-sysc.h> + + vin0: video@e6ef0000 { + compatible = "renesas,vin-r8a7795"; + reg = <0xe6ef0000 0x1000>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 811>; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 811>; + renesas,id = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + vin0csi20: endpoint@0 { + reg = <0>; + remote-endpoint = <&csi20vin0>; + }; + vin0csi40: endpoint@2 { + reg = <2>; + remote-endpoint = <&csi40vin0>; + }; + }; + }; + }; + + # Device node example for Gen3 platform with CSI-2 and parallel + - | + #include <dt-bindings/clock/r8a77970-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a77970-sysc.h> + + vin2: video@e6ef2000 { + compatible = "renesas,vin-r8a77970"; + reg = <0xe6ef2000 0x1000>; + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 809>; + power-domains = <&sysc R8A77970_PD_ALWAYS_ON>; + resets = <&cpg 809>; + renesas,id = <2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + vin2_in: endpoint { + remote-endpoint = <&adv7612_out>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + vin2csi40: endpoint@2 { + reg = <2>; + remote-endpoint = <&csi40vin2>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.yaml b/Documentation/devicetree/bindings/media/renesas,vsp1.yaml new file mode 100644 index 000000000..803358780 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.yaml @@ -0,0 +1,136 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,vsp1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas VSP Video Processing Engine + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: + The VSP is a video processing engine that supports up-/down-scaling, alpha + blending, color space conversion and various other image processing features. + It can be found in the Renesas R-Car Gen2, R-Car Gen3, RZ/G1, and RZ/G2 SoCs. + +properties: + compatible: + oneOf: + - enum: + - renesas,r9a07g044-vsp2 # RZ/G2L + - renesas,vsp1 # R-Car Gen2 and RZ/G1 + - renesas,vsp2 # R-Car Gen3 and RZ/G2 + - items: + - enum: + - renesas,r9a07g043u-vsp2 # RZ/G2UL + - renesas,r9a07g054-vsp2 # RZ/V2L + - renesas,r9a08g046-vsp2 # RZ/G3L + - renesas,r9a09g047-vsp2 # RZ/G3E + - renesas,r9a09g056-vsp2 # RZ/V2N + - renesas,r9a09g057-vsp2 # RZ/V2H(P) + - const: renesas,r9a07g044-vsp2 # RZ/G2L fallback + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: Main clock + - description: Register access clock + - description: Video clock + + clock-names: + items: + - const: aclk + - const: pclk + - const: vclk + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + renesas,fcp: + $ref: /schemas/types.yaml#/definitions/phandle + description: + A phandle referencing the FCP that handles memory accesses for the VSP. + +required: + - compatible + - reg + - interrupts + - clocks + - power-domains + - resets + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + const: renesas,vsp1 + then: + properties: + renesas,fcp: false + else: + required: + - renesas,fcp + + - if: + properties: + compatible: + contains: + const: renesas,r9a07g044-vsp2 + then: + properties: + clocks: + minItems: 3 + required: + - clock-names + else: + properties: + clocks: + maxItems: 1 + clock-names: false + +examples: + # R8A7790 (R-Car H2) VSP1-S + - | + #include <dt-bindings/clock/renesas-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7790-sysc.h> + + vsp@fe928000 { + compatible = "renesas,vsp1"; + reg = <0xfe928000 0x8000>; + interrupts = <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 131>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 131>; + }; + + # R8A77951 (R-Car H3) VSP2-BC + - | + #include <dt-bindings/clock/renesas-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7795-sysc.h> + + vsp@fe920000 { + compatible = "renesas,vsp2"; + reg = <0xfe920000 0x8000>; + interrupts = <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 624>; + power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 624>; + + renesas,fcp = <&fcpvb1>; + }; +... diff --git a/Documentation/devicetree/bindings/media/rockchip,px30-vip.yaml b/Documentation/devicetree/bindings/media/rockchip,px30-vip.yaml new file mode 100644 index 000000000..cc08ce94b --- /dev/null +++ b/Documentation/devicetree/bindings/media/rockchip,px30-vip.yaml @@ -0,0 +1,124 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/rockchip,px30-vip.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip PX30 Video Input Processor (VIP) + +maintainers: + - Mehdi Djait <mehdi.djait@linux.intel.com> + - Michael Riesch <michael.riesch@collabora.com> + +description: + The Rockchip PX30 Video Input Processor (VIP) receives the data from a camera + sensor or CCIR656 encoder and transfers it into system main memory by AXI bus. + +properties: + compatible: + const: rockchip,px30-vip + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: ACLK + - description: HCLK + - description: PCLK + + clock-names: + items: + - const: aclk + - const: hclk + - const: pclk + + resets: + items: + - description: AXI + - description: AHB + - description: PCLK IN + + reset-names: + items: + - const: axi + - const: ahb + - const: pclkin + + power-domains: + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: input port on the parallel interface + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + enum: + - 5 # MEDIA_BUS_TYPE_PARALLEL + - 6 # MEDIA_BUS_TYPE_BT656 + + required: + - bus-type + + required: + - port@0 + +required: + - compatible + - reg + - interrupts + - clocks + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/px30-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/media/video-interfaces.h> + #include <dt-bindings/power/px30-power.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + video-capture@ff490000 { + compatible = "rockchip,px30-vip"; + reg = <0x0 0xff490000 0x0 0x200>; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru ACLK_CIF>, <&cru HCLK_CIF>, <&cru PCLK_CIF>; + clock-names = "aclk", "hclk", "pclk"; + power-domains = <&power PX30_PD_VI>; + resets = <&cru SRST_CIF_A>, <&cru SRST_CIF_H>, <&cru SRST_CIF_PCLKIN>; + reset-names = "axi", "ahb", "pclkin"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + cif_in: endpoint { + remote-endpoint = <&tw9900_out>; + bus-type = <MEDIA_BUS_TYPE_BT656>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/rockchip,rk3568-mipi-csi2.yaml b/Documentation/devicetree/bindings/media/rockchip,rk3568-mipi-csi2.yaml new file mode 100644 index 000000000..8bfad0fca --- /dev/null +++ b/Documentation/devicetree/bindings/media/rockchip,rk3568-mipi-csi2.yaml @@ -0,0 +1,205 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/rockchip,rk3568-mipi-csi2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip MIPI CSI-2 Receiver + +maintainers: + - Michael Riesch <michael.riesch@collabora.com> + +description: + The Rockchip MIPI CSI-2 Receiver is a CSI-2 bridge with one input port and + one output port. It receives the data with the help of an external MIPI PHY + (C-PHY or D-PHY) and passes it to the Rockchip Video Capture (VICAP) block. + +properties: + compatible: + oneOf: + - enum: + - fsl,imx93-mipi-csi2 + - fsl,imx95-mipi-csi2 + - rockchip,rk3568-mipi-csi2 + - items: + - enum: + - rockchip,rk3588-mipi-csi2 + - const: rockchip,rk3568-mipi-csi2 + + reg: + maxItems: 1 + + interrupts: + items: + - description: Interrupt that signals changes in CSI2HOST_ERR1. + - description: Interrupt that signals changes in CSI2HOST_ERR2. + minItems: 1 + + interrupt-names: + items: + - const: err1 + - const: err2 + minItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + items: + - const: per + - const: pixel + minItems: 1 + + phys: + maxItems: 1 + description: MIPI C-PHY or D-PHY. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: Input port node. Connect to e.g., a MIPI CSI-2 image sensor. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + enum: + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY + + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - bus-type + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Output port connected to a Rockchip VICAP port. + + required: + - port@0 + - port@1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - phys + - ports + - power-domains + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + const: rockchip,rk3568-mipi-csi2 + then: + properties: + interrupts: + minItems: 2 + interrupt-names: + minItems: 2 + clocks: + maxItems: 1 + clock-names: + maxItems: 1 + required: + - resets + + - if: + properties: + compatible: + contains: + const: fsl,imx93-mipi-csi2 + then: + properties: + interrupts: + maxItems: 1 + interrupt-names: false + clocks: + minItems: 2 + clock-names: + minItems: 2 + + - if: + properties: + compatible: + contains: + const: fsl,imx95-mipi-csi2 + then: + properties: + interrupts: + maxItems: 1 + interrupt-names: false + clocks: + maxItems: 1 + clock-names: + maxItems: 1 + +examples: + - | + #include <dt-bindings/clock/rk3568-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/media/video-interfaces.h> + #include <dt-bindings/power/rk3568-power.h> + + soc { + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + csi: csi@fdfb0000 { + compatible = "rockchip,rk3568-mipi-csi2"; + reg = <0x0 0xfdfb0000 0x0 0x10000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "err1", "err2"; + clocks = <&cru PCLK_CSI2HOST1>; + phys = <&csi_dphy>; + power-domains = <&power RK3568_PD_VI>; + resets = <&cru SRST_P_CSI2HOST1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi_in: port@0 { + reg = <0>; + + csi_input: endpoint { + bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&imx415_output>; + }; + }; + + csi_out: port@1 { + reg = <1>; + + csi_output: endpoint { + remote-endpoint = <&vicap_mipi_input>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/rockchip,rk3568-vepu.yaml b/Documentation/devicetree/bindings/media/rockchip,rk3568-vepu.yaml new file mode 100644 index 000000000..d246f5d38 --- /dev/null +++ b/Documentation/devicetree/bindings/media/rockchip,rk3568-vepu.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/rockchip,rk3568-vepu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Hantro G1 VPU encoders implemented on Rockchip SoCs + +maintainers: + - Nicolas Frattaroli <frattaroli.nicolas@gmail.com> + +description: + Hantro G1 video encode-only accelerators present on Rockchip SoCs. + +properties: + compatible: + enum: + - rockchip,rk3568-vepu + - rockchip,rk3588-vepu121 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 2 + + clock-names: + items: + - const: aclk + - const: hclk + + power-domains: + maxItems: 1 + + iommus: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3568-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/rk3568-power.h> + + bus { + #address-cells = <2>; + #size-cells = <2>; + + vepu: video-codec@fdee0000 { + compatible = "rockchip,rk3568-vepu"; + reg = <0x0 0xfdee0000 0x0 0x800>; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru ACLK_JENC>, <&cru HCLK_JENC>; + clock-names = "aclk", "hclk"; + iommus = <&vepu_mmu>; + power-domains = <&power RK3568_PD_RGA>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/rockchip,rk3568-vicap.yaml b/Documentation/devicetree/bindings/media/rockchip,rk3568-vicap.yaml new file mode 100644 index 000000000..080b64503 --- /dev/null +++ b/Documentation/devicetree/bindings/media/rockchip,rk3568-vicap.yaml @@ -0,0 +1,307 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/rockchip,rk3568-vicap.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip RK3568 Video Capture (VICAP) + +maintainers: + - Michael Riesch <michael.riesch@collabora.com> + +description: + The Rockchip RK3568 Video Capture (VICAP) block features a digital video + port (DVP, a parallel video interface) and a MIPI CSI-2 port. It receives + the data from camera sensors, video decoders, or other companion ICs and + transfers it into system main memory by AXI bus. + + The Rockchip RK3588 Video Capture (VICAP) is similar to its RK3568 + counterpart, but features six MIPI CSI-2 ports and additional connections + to the image signal processor (ISP) blocks. + +properties: + compatible: + enum: + - rockchip,rk3568-vicap + - rockchip,rk3588-vicap + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 4 + maxItems: 5 + + clock-names: + items: + - const: aclk + - const: hclk + - const: dclk + - const: iclk + - const: iclk1 + minItems: 4 + + iommus: + maxItems: 1 + + resets: + minItems: 5 + maxItems: 9 + + reset-names: + minItems: 5 + maxItems: 9 + + rockchip,grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: Phandle to general register file used for video input block control. + + power-domains: + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + additionalProperties: false + + properties: + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: The digital video port (DVP, a parallel video interface). + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + enum: + - 5 # MEDIA_BUS_TYPE_PARALLEL + - 6 # MEDIA_BUS_TYPE_BT656 + + rockchip,dvp-clk-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0 + minimum: 0 + maximum: 127 + description: + Delay the DVP path clock input to align the sampling phase, + only valid in dual edge sampling mode. Delay is zero by + default and can be adjusted optionally. + + required: + - bus-type + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Port connected to the MIPI CSI-2 receiver 0 output. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: Port connected to the MIPI CSI-2 receiver 1 output. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: Port connected to the MIPI CSI-2 receiver 2 output. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + port@4: + $ref: /schemas/graph.yaml#/properties/port + description: Port connected to the MIPI CSI-2 receiver 3 output. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + port@5: + $ref: /schemas/graph.yaml#/properties/port + description: Port connected to the MIPI CSI-2 receiver 4 output. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + port@6: + $ref: /schemas/graph.yaml#/properties/port + description: Port connected to the MIPI CSI-2 receiver 5 output. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + port@10: + $ref: /schemas/graph.yaml#/properties/port + description: Port connected to the ISP0 input. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + port@11: + $ref: /schemas/graph.yaml#/properties/port + description: Port connected to the ISP1 input. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false +required: + - compatible + - reg + - interrupts + - clocks + - ports + +allOf: + - if: + properties: + compatible: + contains: + const: rockchip,rk3568-vicap + then: + properties: + clocks: + maxItems: 4 + + clock-names: + maxItems: 4 + + resets: + maxItems: 5 + + reset-names: + items: + - const: arst + - const: hrst + - const: drst + - const: prst + - const: irst + + ports: + properties: + port@2: false + + port@3: false + + port@4: false + + port@5: false + + port@6: false + + port@10: false + + port@11: false + + - if: + properties: + compatible: + contains: + const: rockchip,rk3588-vicap + then: + properties: + clocks: + minItems: 5 + + clock-names: + minItems: 5 + + resets: + minItems: 9 + + reset-names: + items: + - const: arst + - const: hrst + - const: drst + - const: irst0 + - const: irst1 + - const: irst2 + - const: irst3 + - const: irst4 + - const: irst5 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3568-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/power/rk3568-power.h> + #include <dt-bindings/media/video-interfaces.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + vicap: video-capture@fdfe0000 { + compatible = "rockchip,rk3568-vicap"; + reg = <0x0 0xfdfe0000 0x0 0x200>; + interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; + assigned-clocks = <&cru DCLK_VICAP>; + assigned-clock-rates = <300000000>; + clocks = <&cru ACLK_VICAP>, <&cru HCLK_VICAP>, + <&cru DCLK_VICAP>, <&cru ICLK_VICAP_G>; + clock-names = "aclk", "hclk", "dclk", "iclk"; + iommus = <&vicap_mmu>; + power-domains = <&power RK3568_PD_VI>; + resets = <&cru SRST_A_VICAP>, <&cru SRST_H_VICAP>, + <&cru SRST_D_VICAP>, <&cru SRST_P_VICAP>, + <&cru SRST_I_VICAP>; + reset-names = "arst", "hrst", "drst", "prst", "irst"; + rockchip,grf = <&grf>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + vicap_dvp: port@0 { + reg = <0>; + + vicap_dvp_input: endpoint { + bus-type = <MEDIA_BUS_TYPE_BT656>; + bus-width = <16>; + pclk-sample = <MEDIA_PCLK_SAMPLE_DUAL_EDGE>; + remote-endpoint = <&it6801_output>; + }; + }; + + vicap_mipi: port@1 { + reg = <1>; + + vicap_mipi_input: endpoint { + remote-endpoint = <&csi_output>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/rockchip,vdec.yaml b/Documentation/devicetree/bindings/media/rockchip,vdec.yaml new file mode 100644 index 000000000..4f38a0ef2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/rockchip,vdec.yaml @@ -0,0 +1,163 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/rockchip,vdec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip Video Decoder (VDec) + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +description: |- + Rockchip SoCs have variants of the same stateless Video Decoder that can + decodes H.264, HEVC, VP9 and AV1 streams, depending on the variant. + +properties: + compatible: + oneOf: + - const: rockchip,rk3288-vdec + - const: rockchip,rk3399-vdec + - const: rockchip,rk3576-vdec + - const: rockchip,rk3588-vdec + - items: + - enum: + - rockchip,rk3228-vdec + - rockchip,rk3328-vdec + - const: rockchip,rk3399-vdec + + reg: + minItems: 1 + maxItems: 3 + + reg-names: + oneOf: + - items: + - const: link + - const: function + - const: cache + - items: + - const: function + - const: link + - const: cache + deprecated: true + description: Use link,function,cache block order instead. + + interrupts: + maxItems: 1 + + clocks: + minItems: 4 + items: + - description: The Video Decoder AXI interface clock + - description: The Video Decoder AHB interface clock + - description: The Video Decoded CABAC clock + - description: The Video Decoder core clock + - description: The Video decoder HEVC CABAC clock + + clock-names: + minItems: 4 + items: + - const: axi + - const: ahb + - const: cabac + - const: core + - const: hevc_cabac + + assigned-clocks: true + + assigned-clock-rates: true + + resets: + items: + - description: The Video Decoder AXI interface reset + - description: The Video Decoder AHB interface reset + - description: The Video Decoded CABAC reset + - description: The Video Decoder core reset + - description: The Video decoder HEVC CABAC reset + + reset-names: + items: + - const: axi + - const: ahb + - const: cabac + - const: core + - const: hevc_cabac + + power-domains: + maxItems: 1 + + iommus: + maxItems: 1 + + sram: + maxItems: 1 + description: + Some SoCs, like rk3588 provide on-chip SRAM to store temporary + buffers during decoding. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + +allOf: + - if: + properties: + compatible: + contains: + enum: + - rockchip,rk3576-vdec + - rockchip,rk3588-vdec + then: + properties: + reg: + minItems: 3 + reg-names: + minItems: 3 + clocks: + minItems: 5 + clock-names: + minItems: 5 + resets: + minItems: 5 + reset-names: + minItems: 5 + required: + - reg-names + else: + properties: + reg: + maxItems: 1 + reg-names: false + clocks: + maxItems: 4 + clock-names: + maxItems: 4 + resets: false + reset-names: false + sram: false + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/rk3399-cru.h> + #include <dt-bindings/power/rk3399-power.h> + + vdec: video-codec@ff660000 { + compatible = "rockchip,rk3399-vdec"; + reg = <0xff660000 0x400>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&cru ACLK_VDU>, <&cru HCLK_VDU>, + <&cru SCLK_VDU_CA>, <&cru SCLK_VDU_CORE>; + clock-names = "axi", "ahb", "cabac", "core"; + power-domains = <&power RK3399_PD_VDU>; + iommus = <&vdec_mmu>; + }; + +... diff --git a/Documentation/devicetree/bindings/media/rockchip-isp1.yaml b/Documentation/devicetree/bindings/media/rockchip-isp1.yaml new file mode 100644 index 000000000..477c21417 --- /dev/null +++ b/Documentation/devicetree/bindings/media/rockchip-isp1.yaml @@ -0,0 +1,341 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR MIT) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/rockchip-isp1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip SoC Image Signal Processing unit v1 + +maintainers: + - Helen Koike <helen.koike@collabora.com> + +description: | + Rockchip ISP1 is the Camera interface for the Rockchip series of SoCs + which contains image processing, scaling, and compression functions. + +properties: + compatible: + enum: + - fsl,imx8mp-isp + - rockchip,px30-cif-isp + - rockchip,rk3399-cif-isp + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 3 + + interrupt-names: + items: + - const: isp + - const: mi + - const: mipi + + clocks: + minItems: 3 + items: + # isp0 and isp1 + - description: ISP clock (for imx8mp, clk) + - description: ISP AXI clock (for imx8mp, m_hclk) + - description: ISP AHB clock (for imx8mp, hclk) + # only for isp1 + - description: ISP Pixel clock + + clock-names: + minItems: 3 + items: + # isp0 and isp1 + - const: isp + - const: aclk + - const: hclk + # only for isp1 + - const: pclk + + fsl,blk-ctrl: + $ref: /schemas/types.yaml#/definitions/phandle-array + maxItems: 1 + description: + A phandle to the media block control for the ISP, followed by a cell + containing the index of the gasket. + + iommus: + maxItems: 1 + + phys: + maxItems: 1 + description: phandle for the PHY port + + phy-names: + const: dphy + + power-domains: + minItems: 1 + items: + - description: ISP power domain + - description: MIPI CSI-2 power domain + + power-domain-names: + minItems: 1 + items: + - const: isp + - const: csi2 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: connection point for sensors at MIPI-DPHY RX0 + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: connection point for input on the parallel interface + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + enum: [5, 6] + + required: + - bus-type + + anyOf: + - required: + - port@0 + - required: + - port@1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + - ports + +allOf: + - if: + properties: + compatible: + contains: + const: rockchip,rk3399-cif-isp + then: + properties: + clocks: + minItems: 3 + maxItems: 4 + clock-names: + minItems: 3 + maxItems: 4 + + - if: + properties: + compatible: + contains: + const: rockchip,px30-cif-isp + then: + required: + - interrupt-names + + - if: + properties: + compatible: + contains: + const: fsl,imx8mp-isp + then: + properties: + clocks: + minItems: 4 + clock-names: + minItems: 4 + iommus: false + phys: false + phy-names: false + power-domains: + minItems: 2 + power-domain-names: + minItems: 2 + required: + - fsl,blk-ctrl + - power-domain-names + else: + properties: + fsl,blk-ctrl: false + power-domains: + maxItems: 1 + power-domain-names: false + required: + - iommus + - phys + - phy-names + +additionalProperties: false + +examples: + - | + + #include <dt-bindings/clock/rk3399-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/rk3399-power.h> + + parent0: parent { + #address-cells = <2>; + #size-cells = <2>; + + isp0: isp0@ff910000 { + compatible = "rockchip,rk3399-cif-isp"; + reg = <0x0 0xff910000 0x0 0x4000>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&cru SCLK_ISP0>, + <&cru ACLK_ISP0_WRAPPER>, + <&cru HCLK_ISP0_WRAPPER>; + clock-names = "isp", "aclk", "hclk"; + iommus = <&isp0_mmu>; + phys = <&dphy>; + phy-names = "dphy"; + power-domains = <&power RK3399_PD_ISP0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + mipi_in_wcam: endpoint@0 { + reg = <0>; + remote-endpoint = <&wcam_out>; + data-lanes = <1 2>; + }; + + mipi_in_ucam: endpoint@1 { + reg = <1>; + remote-endpoint = <&ucam_out>; + data-lanes = <1>; + }; + }; + }; + }; + + i2c7: i2c { + #address-cells = <1>; + #size-cells = <0>; + + wcam: camera@36 { + compatible = "ovti,ov5695"; + reg = <0x36>; + clocks = <&cru SCLK_TESTCLKOUT1>; + + port { + wcam_out: endpoint { + remote-endpoint = <&mipi_in_wcam>; + data-lanes = <1 2>; + }; + }; + }; + + ucam: camera@3c { + compatible = "ovti,ov2685"; + reg = <0x3c>; + + clocks = <&cru SCLK_TESTCLKOUT1>; + clock-names = "xvclk"; + + avdd-supply = <&pp2800_cam>; + dovdd-supply = <&pp1800>; + dvdd-supply = <&pp1800>; + + port { + ucam_out: endpoint { + remote-endpoint = <&mipi_in_ucam>; + data-lanes = <1>; + }; + }; + }; + }; + }; + + - | + + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/px30-power.h> + + parent1: parent { + #address-cells = <2>; + #size-cells = <2>; + + isp: isp@ff4a0000 { + compatible = "rockchip,px30-cif-isp"; + reg = <0x0 0xff4a0000 0x0 0x8000>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "isp", "mi", "mipi"; + clocks = <&cru SCLK_ISP0>, + <&cru ACLK_ISP0_WRAPPER>, + <&cru HCLK_ISP0_WRAPPER>, + <&cru PCLK_ISP1_WRAPPER>; + clock-names = "isp", "aclk", "hclk", "pclk"; + iommus = <&isp_mmu>; + phys = <&csi_dphy>; + phy-names = "dphy"; + power-domains = <&power PX30_PD_VI>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + mipi_in_ucam1: endpoint@0 { + reg = <0>; + remote-endpoint = <&ucam1_out>; + data-lanes = <1 2>; + }; + }; + }; + }; + + i2c2: i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov5695: camera@36 { + compatible = "ovti,ov5647"; + reg = <0x36>; + clocks = <&cru SCLK_CIF_OUT>; + + port { + ucam1_out: endpoint { + remote-endpoint = <&mipi_in_ucam1>; + data-lanes = <1 2>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/rockchip-rga.yaml b/Documentation/devicetree/bindings/media/rockchip-rga.yaml new file mode 100644 index 000000000..7bd92f733 --- /dev/null +++ b/Documentation/devicetree/bindings/media/rockchip-rga.yaml @@ -0,0 +1,94 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/rockchip-rga.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip 2D raster graphic acceleration controller (RGA) + +description: + RGA is a standalone 2D raster graphic acceleration unit. It accelerates 2D + graphics operations, such as point/line drawing, image scaling, rotation, + BitBLT, alpha blending and image blur/sharpness. There exist many versions + of this unit that differ in the supported inputs/output formats, + the attached IOMMU and the supported operations on the input. As some SoCs + include multiple RGA units with different versions, a more specific + compatible name to differentiate the concrete unit is used for them. + +maintainers: + - Jacob Chen <jacob-chen@iotwrt.com> + - Ezequiel Garcia <ezequiel@collabora.com> + +properties: + compatible: + oneOf: + - const: rockchip,rk3288-rga + - const: rockchip,rk3399-rga + - const: rockchip,rk3588-rga3 + - items: + - enum: + - rockchip,rk3228-rga + - rockchip,rk3568-rga + - rockchip,rk3588-rga + - const: rockchip,rk3288-rga + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 3 + + clock-names: + items: + - const: aclk + - const: hclk + - const: sclk + + power-domains: + maxItems: 1 + + iommus: + maxItems: 1 + + resets: + maxItems: 3 + + reset-names: + items: + - const: core + - const: axi + - const: ahb + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3399-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/rk3399-power.h> + rga: rga@ff680000 { + compatible = "rockchip,rk3399-rga"; + reg = <0xff680000 0x10000>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru ACLK_RGA>, + <&cru HCLK_RGA>, + <&cru SCLK_RGA_CORE>; + clock-names = "aclk", "hclk", "sclk"; + power-domains = <&power RK3399_PD_RGA>; + resets = <&cru SRST_RGA_CORE>, + <&cru SRST_A_RGA>, + <&cru SRST_H_RGA>; + reset-names = "core", "axi", "ahb"; + }; diff --git a/Documentation/devicetree/bindings/media/rockchip-vpu.yaml b/Documentation/devicetree/bindings/media/rockchip-vpu.yaml new file mode 100644 index 000000000..8c2501634 --- /dev/null +++ b/Documentation/devicetree/bindings/media/rockchip-vpu.yaml @@ -0,0 +1,108 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/rockchip-vpu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Hantro G1 VPU codecs implemented on Rockchip SoCs + +maintainers: + - Ezequiel Garcia <ezequiel@collabora.com> + +description: + Hantro G1 video encode and decode accelerators present on Rockchip SoCs. + +properties: + compatible: + oneOf: + - enum: + - rockchip,rk3036-vpu + - rockchip,rk3066-vpu + - rockchip,rk3288-vpu + - rockchip,rk3328-vpu + - rockchip,rk3399-vpu + - rockchip,px30-vpu + - rockchip,rk3568-vpu + - rockchip,rk3588-av1-vpu + - items: + - enum: + - rockchip,rk3128-vpu + - rockchip,rk3188-vpu + - const: rockchip,rk3066-vpu + - items: + - const: rockchip,rk3228-vpu + - const: rockchip,rk3399-vpu + - items: + - const: rockchip,rk3588-vpu121 + - const: rockchip,rk3568-vpu + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 2 + + interrupt-names: + oneOf: + - const: vdpu + - items: + - const: vepu + - const: vdpu + + clocks: + oneOf: + - maxItems: 2 + - maxItems: 4 + + clock-names: + oneOf: + - items: + - const: aclk + - const: hclk + - items: + - const: aclk_vdpu + - const: hclk_vdpu + - const: aclk_vepu + - const: hclk_vepu + + power-domains: + maxItems: 1 + + iommus: + maxItems: 1 + + resets: + items: + - description: AXI reset line + - description: AXI bus interface unit reset line + - description: APB reset line + - description: APB bus interface unit reset line + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3288-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/rk3288-power.h> + + video-codec@ff9a0000 { + compatible = "rockchip,rk3288-vpu"; + reg = <0xff9a0000 0x800>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "vepu", "vdpu"; + clocks = <&cru ACLK_VCODEC>, <&cru HCLK_VCODEC>; + clock-names = "aclk", "hclk"; + power-domains = <&power RK3288_PD_VIDEO>; + iommus = <&vpu_mmu>; + }; diff --git a/Documentation/devicetree/bindings/media/samsung,exynos4210-csis.yaml b/Documentation/devicetree/bindings/media/samsung,exynos4210-csis.yaml new file mode 100644 index 000000000..2ddca4167 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung,exynos4210-csis.yaml @@ -0,0 +1,170 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/samsung,exynos4210-csis.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5P/Exynos SoC series MIPI CSI-2 receiver (MIPI CSIS) + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + +properties: + compatible: + enum: + - samsung,s5pv210-csis + - samsung,exynos4210-csis + - samsung,exynos4212-csis + - samsung,exynos5250-csis + + reg: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + bus-width: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [2, 4] + description: + Number of data lines supported. + + clocks: + maxItems: 2 + + clock-names: + items: + - const: csis + - const: sclk_csis + + clock-frequency: + default: 166000000 + description: + The IP's main (system bus) clock frequency in Hz. + + interrupts: + maxItems: 1 + + phys: + maxItems: 1 + + phy-names: + items: + - const: csis + + power-domains: + maxItems: 1 + + vddio-supply: + description: MIPI CSIS I/O and PLL voltage supply (e.g. 1.8V). + + vddcore-supply: + description: MIPI CSIS Core voltage supply (e.g. 1.1V). + +patternProperties: + "^port@[34]$": + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + description: + Camera input port. + + properties: + reg: + enum: [3, 4] + + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 4 + + samsung,csis-hs-settle: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Differential receiver (HS-RX) settle time. + + samsung,csis-wclk: + type: boolean + description: + CSI-2 wrapper clock selection. If this property is present external clock + from CMU will be used, or the bus clock if it's not specified. + + required: + - data-lanes + + required: + - reg + +required: + - compatible + - reg + - bus-width + - clocks + - clock-names + - interrupts + - vddio-supply + - vddcore-supply + +anyOf: + - required: + - port@3 + - required: + - port@4 + +allOf: + - if: + required: + - samsung,isp-wb + then: + required: + - samsung,sysreg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos4.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + csis@11890000 { + compatible = "samsung,exynos4210-csis"; + reg = <0x11890000 0x4000>; + clocks = <&clock CLK_CSIS1>, + <&clock CLK_SCLK_CSIS1>; + clock-names = "csis", "sclk_csis"; + assigned-clocks = <&clock CLK_MOUT_CSIS1>, + <&clock CLK_SCLK_CSIS1>; + assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; + assigned-clock-rates = <0>, <176000000>; + + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; + + bus-width = <2>; + power-domains = <&pd_cam>; + phys = <&mipi_phy 2>; + phy-names = "csis"; + + vddcore-supply = <&ldo8_reg>; + vddio-supply = <&ldo10_reg>; + + #address-cells = <1>; + #size-cells = <0>; + + /* Camera D (4) MIPI CSI-2 (CSIS1) */ + port@4 { + reg = <4>; + + endpoint { + remote-endpoint = <&is_s5k6a3_ep>; + data-lanes = <1>; + samsung,csis-hs-settle = <18>; + samsung,csis-wclk; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/samsung,exynos4210-fimc.yaml b/Documentation/devicetree/bindings/media/samsung,exynos4210-fimc.yaml new file mode 100644 index 000000000..17ece4eb3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung,exynos4210-fimc.yaml @@ -0,0 +1,152 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/samsung,exynos4210-fimc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5P/Exynos SoC Fully Integrated Mobile Camera + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + +description: + Each FIMC device should have an alias in the aliases node, in the form of + fimc<n>, where <n> is an integer specifying the IP block instance. + +properties: + compatible: + enum: + - samsung,exynos4210-fimc + - samsung,exynos4212-fimc + - samsung,s5pv210-fimc + + reg: + maxItems: 1 + + clocks: + maxItems: 2 + + clock-names: + items: + - const: fimc + - const: sclk_fimc + + clock-frequency: + description: + Maximum FIMC local clock (LCLK) frequency. + + interrupts: + maxItems: 1 + + iommus: + maxItems: 1 + + power-domains: + maxItems: 1 + + samsung,cam-if: + type: boolean + description: + The FIMC IP block includes the camera input interface. + + samsung,isp-wb: + type: boolean + description: | + The FIMC IP block has the ISP writeback input. + + samsung,lcd-wb: + type: boolean + description: | + The FIMC IP block has the LCD writeback input. + + samsung,mainscaler-ext: + type: boolean + description: + FIMC IP supports extended image size and has CIEXTEN register. + + samsung,min-pix-alignment: + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + - description: Minimum supported image height alignment. + - description: Horizontal image offset. + description: + The values are in pixels and default is <2 1>. + + samsung,min-pix-sizes: + $ref: /schemas/types.yaml#/definitions/uint32-array + maxItems: 2 + description: | + An array specifying minimum image size in pixels at the FIMC input and + output DMA, in the first and second cell respectively. Default value + is <16 16>. + + samsung,pix-limits: + $ref: /schemas/types.yaml#/definitions/uint32-array + maxItems: 4 + description: | + An array of maximum supported image sizes in pixels, for details refer to + Table 2-1 in the S5PV210 SoC User Manual. The meaning of each cell is as + follows: + 0 - scaler input horizontal size + 1 - input horizontal size for the scaler bypassed + 2 - REAL_WIDTH without input rotation + 3 - REAL_HEIGHT with input rotation + + samsung,rotators: + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0x11 + description: | + A bitmask specifying whether this IP has the input and the output + rotator. Bits 4 and 0 correspond to input and output rotator + respectively. If a rotator is present its corresponding bit should be + set. + + samsung,sysreg: + $ref: /schemas/types.yaml#/definitions/phandle + description: + System Registers (SYSREG) node. + +required: + - compatible + - reg + - clocks + - clock-names + - samsung,pix-limits + +allOf: + - if: + required: + - samsung,isp-wb + then: + required: + - samsung,sysreg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos4.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + fimc@11800000 { + compatible = "samsung,exynos4212-fimc"; + reg = <0x11800000 0x1000>; + clocks = <&clock CLK_FIMC0>, + <&clock CLK_SCLK_FIMC0>; + clock-names = "fimc", "sclk_fimc"; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&sysmmu_fimc0>; + power-domains = <&pd_cam>; + samsung,sysreg = <&sys_reg>; + + samsung,pix-limits = <4224 8192 1920 4224>; + samsung,mainscaler-ext; + samsung,isp-wb; + samsung,cam-if; + + assigned-clocks = <&clock CLK_MOUT_FIMC0>, + <&clock CLK_SCLK_FIMC0>; + assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; + assigned-clock-rates = <0>, <176000000>; + }; diff --git a/Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-is.yaml b/Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-is.yaml new file mode 100644 index 000000000..c8894358c --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-is.yaml @@ -0,0 +1,225 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/samsung,exynos4212-fimc-is.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Exynos4212/4412 SoC Imaging Subsystem (FIMC-IS) + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + +description: + The FIMC-IS is a subsystem for processing image signal from an image sensor. + The Exynos4x12 SoC series FIMC-IS V1.5 comprises of a dedicated ARM Cortex-A5 + processor, ISP, DRC and FD IP blocks and peripheral devices such as UART, I2C + and SPI bus controllers, PWM and ADC. + +properties: + compatible: + enum: + - samsung,exynos4212-fimc-is + + reg: + maxItems: 1 + + ranges: true + + '#address-cells': + const: 1 + + '#size-cells': + const: 1 + + clocks: + maxItems: 21 + + clock-names: + items: + - const: lite0 + - const: lite1 + - const: ppmuispx + - const: ppmuispmx + - const: isp + - const: drc + - const: fd + - const: mcuisp + - const: gicisp + - const: mcuctl_isp + - const: pwm_isp + - const: ispdiv0 + - const: ispdiv1 + - const: mcuispdiv0 + - const: mcuispdiv1 + - const: mpll + - const: aclk200 + - const: aclk400mcuisp + - const: div_aclk200 + - const: div_aclk400mcuisp + - const: uart + + interrupts: + maxItems: 2 + + iommus: + maxItems: 4 + + iommu-names: + items: + - const: isp + - const: drc + - const: fd + - const: mcuctl + + power-domains: + maxItems: 1 + + samsung,pmu-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Power Management Unit (PMU) system controller interface, used to + power/start the ISP. + +patternProperties: + "^pmu@[0-9a-f]+$": + type: object + additionalProperties: false + deprecated: true + description: + Node representing the SoC's Power Management Unit (duplicated with the + correct PMU node in the SoC). Deprecated, use samsung,pmu-syscon. + + properties: + reg: + maxItems: 1 + + required: + - reg + + "^i2c-isp@[0-9a-f]+$": + type: object + $ref: /schemas/i2c/i2c-controller.yaml# + unevaluatedProperties: false + description: + ISP I2C bus controller + + properties: + compatible: + const: samsung,exynos4212-i2c-isp + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: i2c_isp + + pinctrl-0: true + pinctrl-names: + items: + - const: default + + required: + - compatible + - reg + - clocks + - clock-names + +required: + - compatible + - reg + - '#address-cells' + - clocks + - clock-names + - interrupts + - ranges + - samsung,pmu-syscon + - '#size-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos4.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + fimc-is@12000000 { + compatible = "samsung,exynos4212-fimc-is"; + reg = <0x12000000 0x260000>; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&isp_clock CLK_ISP_FIMC_LITE0>, + <&isp_clock CLK_ISP_FIMC_LITE1>, + <&isp_clock CLK_ISP_PPMUISPX>, + <&isp_clock CLK_ISP_PPMUISPMX>, + <&isp_clock CLK_ISP_FIMC_ISP>, + <&isp_clock CLK_ISP_FIMC_DRC>, + <&isp_clock CLK_ISP_FIMC_FD>, + <&isp_clock CLK_ISP_MCUISP>, + <&isp_clock CLK_ISP_GICISP>, + <&isp_clock CLK_ISP_MCUCTL_ISP>, + <&isp_clock CLK_ISP_PWM_ISP>, + <&isp_clock CLK_ISP_DIV_ISP0>, + <&isp_clock CLK_ISP_DIV_ISP1>, + <&isp_clock CLK_ISP_DIV_MCUISP0>, + <&isp_clock CLK_ISP_DIV_MCUISP1>, + <&clock CLK_MOUT_MPLL_USER_T>, + <&clock CLK_ACLK200>, + <&clock CLK_ACLK400_MCUISP>, + <&clock CLK_DIV_ACLK200>, + <&clock CLK_DIV_ACLK400_MCUISP>, + <&clock CLK_UART_ISP_SCLK>; + clock-names = "lite0", "lite1", "ppmuispx", + "ppmuispmx", "isp", + "drc", "fd", "mcuisp", + "gicisp", "mcuctl_isp", "pwm_isp", + "ispdiv0", "ispdiv1", "mcuispdiv0", + "mcuispdiv1", "mpll", "aclk200", + "aclk400mcuisp", "div_aclk200", + "div_aclk400mcuisp", "uart"; + iommus = <&sysmmu_fimc_isp>, <&sysmmu_fimc_drc>, + <&sysmmu_fimc_fd>, <&sysmmu_fimc_mcuctl>; + iommu-names = "isp", "drc", "fd", "mcuctl"; + power-domains = <&pd_isp>; + samsung,pmu-syscon = <&pmu_system_controller>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + i2c-isp@12140000 { + compatible = "samsung,exynos4212-i2c-isp"; + reg = <0x12140000 0x100>; + clocks = <&isp_clock CLK_ISP_I2C1_ISP>; + clock-names = "i2c_isp"; + pinctrl-0 = <&fimc_is_i2c1>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + + image-sensor@10 { + compatible = "samsung,s5k6a3"; + reg = <0x10>; + svdda-supply = <&cam_io_reg>; + svddio-supply = <&ldo19_reg>; + afvdd-supply = <&ldo19_reg>; + clocks = <&camera 1>; + clock-names = "extclk"; + assigned-clocks = <&camera 1>; + assigned-clock-rates = <24000000>; + gpios = <&gpm1 6 GPIO_ACTIVE_LOW>; + + port { + endpoint { + remote-endpoint = <&csis1_ep>; + data-lanes = <1>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-lite.yaml b/Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-lite.yaml new file mode 100644 index 000000000..bda724897 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-lite.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/samsung,exynos4212-fimc-lite.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Exynos SoC series camera host interface (FIMC-LITE) + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + +description: + Each FIMC device should have an alias in the aliases node, in the form of + fimc-lite<n>, where <n> is an integer specifying the IP block instance. + +properties: + compatible: + enum: + - samsung,exynos4212-fimc-lite + - samsung,exynos5250-fimc-lite + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: flite + + interrupts: + maxItems: 1 + + iommus: + maxItems: 1 + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos4.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + fimc-lite@12390000 { + compatible = "samsung,exynos4212-fimc-lite"; + reg = <0x12390000 0x1000>; + clocks = <&isp_clock CLK_ISP_FIMC_LITE0>; + clock-names = "flite"; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&pd_isp>; + iommus = <&sysmmu_fimc_lite0>; + }; diff --git a/Documentation/devicetree/bindings/media/samsung,exynos5250-gsc.yaml b/Documentation/devicetree/bindings/media/samsung,exynos5250-gsc.yaml new file mode 100644 index 000000000..9196cf5da --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung,exynos5250-gsc.yaml @@ -0,0 +1,109 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/samsung,exynos5250-gsc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Exynos SoC G-Scaler + +maintainers: + - Inki Dae <inki.dae@samsung.com> + - Krzysztof Kozlowski <krzk@kernel.org> + - Seung-Woo Kim <sw0312.kim@samsung.com> + +description: + G-Scaler is used for scaling and color space conversion on Samsung Exynos + SoCs. + + Each G-Scaler node should have a numbered alias in the aliases node, in the + form of gscN, N = 0...3. + +properties: + compatible: + oneOf: + - items: + - enum: + - samsung,exynos5250-gsc + - samsung,exynos5420-gsc + - const: samsung,exynos5-gsc + - enum: + - samsung,exynos5433-gsc + - const: samsung,exynos5-gsc + deprecated: True + + clocks: + minItems: 1 + maxItems: 5 + + clock-names: + minItems: 1 + maxItems: 5 + + interrupts: + maxItems: 1 + + iommus: + maxItems: 1 + + power-domains: + maxItems: 1 + + reg: + maxItems: 1 + + samsung,sysreg: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Syscon used to control the system registers to set writeback input and destination. + +required: + - compatible + - clocks + - clock-names + - interrupts + - reg + +allOf: + - if: + properties: + compatible: + contains: + enum: + - samsung,exynos5-gsc + - samsung,exynos5250-gsc + - samsung,exynos5420-gsc + then: + properties: + clocks: + maxItems: 1 + clock-names: + items: + - const: gscl + else: + properties: + clocks: + minItems: 5 + clock-names: + items: + - const: pclk + - const: aclk + - const: aclk_xiu + - const: aclk_gsclbend + - const: gsd + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos5250.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + video-scaler@13e00000 { + compatible = "samsung,exynos5250-gsc", "samsung,exynos5-gsc"; + reg = <0x13e00000 0x1000>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&pd_gsc>; + clocks = <&clock CLK_GSCL0>; + clock-names = "gscl"; + iommus = <&sysmmu_gsc0>; + }; diff --git a/Documentation/devicetree/bindings/media/samsung,fimc.yaml b/Documentation/devicetree/bindings/media/samsung,fimc.yaml new file mode 100644 index 000000000..1bfba84f8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung,fimc.yaml @@ -0,0 +1,278 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/samsung,fimc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5P/Exynos SoC Camera Subsystem (FIMC) + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + +description: | + The S5P/Exynos SoC Camera subsystem comprises of multiple sub-devices + represented by separate device tree nodes. Currently this includes: Fully + Integrated Mobile Camera (FIMC, in the S5P SoCs series known as CAMIF), MIPI + CSIS, FIMC-LITE and FIMC-IS (ISP). + +properties: + compatible: + const: samsung,fimc + + ranges: true + + '#address-cells': + const: 1 + + '#size-cells': + const: 1 + + '#clock-cells': + const: 1 + description: | + The clock specifier cell stores an index of a clock: 0, 1 for + CAM_A_CLKOUT, CAM_B_CLKOUT clocks respectively. + + clocks: + minItems: 2 + maxItems: 4 + + clock-names: + minItems: 2 + items: + - const: sclk_cam0 + - const: sclk_cam1 + - const: pxl_async0 + - const: pxl_async1 + + clock-output-names: + maxItems: 2 + + parallel-ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Active parallel video input ports. + + patternProperties: + "^port@[01]$": + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Camera A and camera B inputs. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + pinctrl-names: + minItems: 1 + items: + - const: default + - const: idle + - const: active_a + - const: active_b + +patternProperties: + "^csis@[0-9a-f]+$": + type: object + $ref: samsung,exynos4210-csis.yaml# + description: MIPI CSI-2 receiver. + + "^fimc@[0-9a-f]+$": + type: object + $ref: samsung,exynos4210-fimc.yaml# + description: Fully Integrated Mobile Camera. + + "^fimc-is@[0-9a-f]+$": + type: object + $ref: samsung,exynos4212-fimc-is.yaml# + description: Imaging Subsystem (FIMC-IS). + + "^fimc-lite@[0-9a-f]+$": + type: object + $ref: samsung,exynos4212-fimc-lite.yaml# + description: Camera host interface (FIMC-LITE). + +required: + - compatible + - '#address-cells' + - '#clock-cells' + - clocks + - clock-names + - clock-output-names + - ranges + - '#size-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos4.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + camera@11800000 { + compatible = "samsung,fimc"; + #clock-cells = <1>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0xba1000>; + + clocks = <&clock CLK_SCLK_CAM0>, <&clock CLK_SCLK_CAM1>, + <&clock CLK_PIXELASYNCM0>, <&clock CLK_PIXELASYNCM1>; + clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", "pxl_async1"; + clock-output-names = "cam_a_clkout", "cam_b_clkout"; + + assigned-clocks = <&clock CLK_MOUT_CAM0>, + <&clock CLK_MOUT_CAM1>; + assigned-clock-parents = <&clock CLK_XUSBXTI>, + <&clock CLK_XUSBXTI>; + + pinctrl-0 = <&cam_port_a_clk_active &cam_port_b_clk_active>; + pinctrl-names = "default"; + + fimc@0 { + compatible = "samsung,exynos4212-fimc"; + reg = <0x00000000 0x1000>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clock CLK_FIMC0>, + <&clock CLK_SCLK_FIMC0>; + clock-names = "fimc", "sclk_fimc"; + power-domains = <&pd_cam>; + samsung,sysreg = <&sys_reg>; + iommus = <&sysmmu_fimc0>; + + samsung,pix-limits = <4224 8192 1920 4224>; + samsung,mainscaler-ext; + samsung,isp-wb; + samsung,cam-if; + }; + + /* ... FIMC 1-3 */ + + csis@80000 { + compatible = "samsung,exynos4210-csis"; + reg = <0x00080000 0x4000>; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clock CLK_CSIS0>, + <&clock CLK_SCLK_CSIS0>; + clock-names = "csis", "sclk_csis"; + assigned-clocks = <&clock CLK_MOUT_CSIS0>, + <&clock CLK_SCLK_CSIS0>; + assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; + assigned-clock-rates = <0>, <176000000>; + + bus-width = <4>; + power-domains = <&pd_cam>; + phys = <&mipi_phy 0>; + phy-names = "csis"; + #address-cells = <1>; + #size-cells = <0>; + + vddcore-supply = <&ldo8_reg>; + vddio-supply = <&ldo10_reg>; + + /* Camera C (3) MIPI CSI-2 (CSIS0) */ + port@3 { + reg = <3>; + endpoint { + remote-endpoint = <&s5c73m3_ep>; + data-lanes = <1 2 3 4>; + samsung,csis-hs-settle = <12>; + }; + }; + }; + + /* ... CSIS 1 */ + + fimc-lite@b90000 { + compatible = "samsung,exynos4212-fimc-lite"; + reg = <0xb90000 0x1000>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&pd_isp>; + clocks = <&isp_clock CLK_ISP_FIMC_LITE0>; + clock-names = "flite"; + iommus = <&sysmmu_fimc_lite0>; + }; + + /* ... FIMC-LITE 1 */ + + fimc-is@800000 { + compatible = "samsung,exynos4212-fimc-is"; + reg = <0x00800000 0x260000>; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&isp_clock CLK_ISP_FIMC_LITE0>, + <&isp_clock CLK_ISP_FIMC_LITE1>, + <&isp_clock CLK_ISP_PPMUISPX>, + <&isp_clock CLK_ISP_PPMUISPMX>, + <&isp_clock CLK_ISP_FIMC_ISP>, + <&isp_clock CLK_ISP_FIMC_DRC>, + <&isp_clock CLK_ISP_FIMC_FD>, + <&isp_clock CLK_ISP_MCUISP>, + <&isp_clock CLK_ISP_GICISP>, + <&isp_clock CLK_ISP_MCUCTL_ISP>, + <&isp_clock CLK_ISP_PWM_ISP>, + <&isp_clock CLK_ISP_DIV_ISP0>, + <&isp_clock CLK_ISP_DIV_ISP1>, + <&isp_clock CLK_ISP_DIV_MCUISP0>, + <&isp_clock CLK_ISP_DIV_MCUISP1>, + <&clock CLK_MOUT_MPLL_USER_T>, + <&clock CLK_ACLK200>, + <&clock CLK_ACLK400_MCUISP>, + <&clock CLK_DIV_ACLK200>, + <&clock CLK_DIV_ACLK400_MCUISP>, + <&clock CLK_UART_ISP_SCLK>; + clock-names = "lite0", "lite1", "ppmuispx", + "ppmuispmx", "isp", + "drc", "fd", "mcuisp", + "gicisp", "mcuctl_isp", "pwm_isp", + "ispdiv0", "ispdiv1", "mcuispdiv0", + "mcuispdiv1", "mpll", "aclk200", + "aclk400mcuisp", "div_aclk200", + "div_aclk400mcuisp", "uart"; + iommus = <&sysmmu_fimc_isp>, <&sysmmu_fimc_drc>, + <&sysmmu_fimc_fd>, <&sysmmu_fimc_mcuctl>; + iommu-names = "isp", "drc", "fd", "mcuctl"; + power-domains = <&pd_isp>; + samsung,pmu-syscon = <&pmu_system_controller>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + i2c-isp@940000 { + compatible = "samsung,exynos4212-i2c-isp"; + reg = <0x00940000 0x100>; + clocks = <&isp_clock CLK_ISP_I2C1_ISP>; + clock-names = "i2c_isp"; + pinctrl-0 = <&fimc_is_i2c1>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + + image-sensor@10 { + compatible = "samsung,s5k6a3"; + reg = <0x10>; + svdda-supply = <&cam_io_reg>; + svddio-supply = <&ldo19_reg>; + afvdd-supply = <&ldo19_reg>; + /* CAM_B_CLKOUT */ + clocks = <&camera 1>; + clock-names = "extclk"; + assigned-clocks = <&camera 1>; + assigned-clock-rates = <24000000>; + gpios = <&gpm1 6 GPIO_ACTIVE_LOW>; + + port { + endpoint { + remote-endpoint = <&csis1_ep>; + data-lanes = <1>; + }; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/samsung,s5c73m3.yaml b/Documentation/devicetree/bindings/media/samsung,s5c73m3.yaml new file mode 100644 index 000000000..1af5d7ac3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung,s5c73m3.yaml @@ -0,0 +1,165 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/samsung,s5c73m3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5C73M3 8Mp camera ISP + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + +description: + The S5C73M3 camera ISP supports MIPI CSI-2 and parallel (ITU-R BT.656) + video data busses. The I2C bus is the main control bus and additionally the + SPI bus is used, mostly for transferring the firmware to and from the + device. Two slave device nodes corresponding to these control bus + interfaces are required and should be placed under respective bus + controller nodes. + +properties: + compatible: + const: samsung,s5c73m3 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: cis_extclk + + clock-frequency: + default: 24000000 + description: cis_extclk clock frequency. + + standby-gpios: + maxItems: 1 + description: STANDBY pin. + + vdda-supply: + description: Analog power supply (1.2V). + + vdd-af-supply: + description: lens power supply (2.8V). + + vddio-cis-supply: + description: CIS I/O power supply (1.2V to 1.8V). + + vddio-host-supply: + description: Host I/O power supply (1.8V to 2.8V). + + vdd-int-supply: + description: Digital power supply (1.2V). + + vdd-reg-supply: + description: Regulator input power supply (2.8V). + + xshutdown-gpios: + maxItems: 1 + description: XSHUTDOWN pin. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + +required: + - compatible + - reg + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + - if: + required: + - spi-max-frequency + then: + properties: + # The SPI node is simplified firmware-transfer interface only + clocks: false + clock-names: false + standby-gpios: false + vdda-supply: false + vdd-af-supply: false + vddio-cis-supply: false + vddio-host-supply: false + vdd-int-supply: false + vdd-reg-supply: false + xshutdown-gpios: false + port: false + else: + required: + - clocks + - clock-names + - standby-gpios + - vdda-supply + - vdd-af-supply + - vddio-cis-supply + - vddio-host-supply + - vdd-int-supply + - vdd-reg-supply + - xshutdown-gpios + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + image-sensor@3c { + compatible = "samsung,s5c73m3"; + reg = <0x3c>; + clock-frequency = <24000000>; + clocks = <&camera 0>; + clock-names = "cis_extclk"; + standby-gpios = <&gpm0 6 GPIO_ACTIVE_LOW>; + vdda-supply = <&cam_vdda_reg>; + vdd-af-supply = <&cam_af_reg>; + vddio-cis-supply = <&ldo9_reg>; + vddio-host-supply = <&ldo18_reg>; + vdd-int-supply = <&buck9_reg>; + vdd-reg-supply = <&cam_io_reg>; + xshutdown-gpios = <&gpf1 3 GPIO_ACTIVE_LOW>; /* ISP_RESET */ + + port { + s5c73m3_ep: endpoint { + remote-endpoint = <&csis0_ep>; + data-lanes = <1 2 3 4>; + }; + }; + }; + }; + + spi { + #address-cells = <1>; + #size-cells = <0>; + + image-sensor@0 { + compatible = "samsung,s5c73m3"; + reg = <0>; + spi-max-frequency = <50000000>; + controller-data { + samsung,spi-feedback-delay = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/samsung,s5p-mfc.yaml b/Documentation/devicetree/bindings/media/samsung,s5p-mfc.yaml new file mode 100644 index 000000000..b46cc7807 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung,s5p-mfc.yaml @@ -0,0 +1,195 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/samsung,s5p-mfc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Exynos Multi Format Codec (MFC) + +maintainers: + - Marek Szyprowski <m.szyprowski@samsung.com> + - Aakarsh Jain <aakarsh.jain@samsung.com> + +description: + Multi Format Codec (MFC) is the IP present in Samsung SoCs which + supports high resolution decoding and encoding functionalities. + +properties: + compatible: + oneOf: + - enum: + - samsung,exynos5433-mfc # Exynos5433 + - samsung,mfc-v5 # Exynos4 + - samsung,mfc-v6 # Exynos5 + - samsung,mfc-v7 # Exynos5420 + - samsung,mfc-v8 # Exynos5800 + - samsung,mfc-v10 # Exynos7880 + - tesla,fsd-mfc # Tesla FSD + - items: + - enum: + - samsung,exynos3250-mfc # Exynos3250 + - const: samsung,mfc-v7 # Fall back for Exynos3250 + + reg: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 3 + + clock-names: + minItems: 1 + maxItems: 3 + + interrupts: + maxItems: 1 + + iommus: + minItems: 1 + maxItems: 2 + + iommu-names: + minItems: 1 + items: + - const: left + - const: right + + power-domains: + maxItems: 1 + + memory-region: + minItems: 1 + maxItems: 2 + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + enum: + - samsung,exynos3250-mfc + then: + properties: + clocks: + maxItems: 2 + clock-names: + items: + - const: mfc + - const: sclk_mfc + iommus: + maxItems: 1 + iommu-names: false + + - if: + properties: + compatible: + contains: + enum: + - samsung,exynos5433-mfc + then: + properties: + clocks: + maxItems: 3 + clock-names: + items: + - const: pclk + - const: aclk + - const: aclk_xiu + iommus: + minItems: 2 + iommu-names: + minItems: 2 + + - if: + properties: + compatible: + contains: + enum: + - samsung,mfc-v5 + then: + properties: + clocks: + maxItems: 2 + clock-names: + items: + - const: mfc + - const: sclk_mfc + iommus: + minItems: 2 + iommu-names: + minItems: 2 + + - if: + properties: + compatible: + contains: + enum: + - samsung,mfc-v6 + - samsung,mfc-v8 + then: + properties: + clocks: + maxItems: 1 + clock-names: + items: + - const: mfc + iommus: + minItems: 2 + iommu-names: + minItems: 2 + + - if: + properties: + compatible: + contains: + enum: + - samsung,mfc-v7 + then: + properties: + clocks: + minItems: 1 + maxItems: 2 + + - if: + properties: + compatible: + contains: + enum: + - tesla,fsd-mfc + then: + properties: + clocks: + maxItems: 1 + clock-names: + items: + - const: mfc + iommus: + maxItems: 2 + iommus-names: false + +examples: + - | + #include <dt-bindings/clock/exynos4.h> + #include <dt-bindings/clock/exynos-audss-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + codec@13400000 { + compatible = "samsung,mfc-v5"; + reg = <0x13400000 0x10000>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&pd_mfc>; + clocks = <&clock CLK_MFC>, <&clock CLK_SCLK_MFC>; + clock-names = "mfc", "sclk_mfc"; + iommus = <&sysmmu_mfc_l>, <&sysmmu_mfc_r>; + iommu-names = "left", "right"; + }; diff --git a/Documentation/devicetree/bindings/media/samsung,s5pv210-jpeg.yaml b/Documentation/devicetree/bindings/media/samsung,s5pv210-jpeg.yaml new file mode 100644 index 000000000..5c969e764 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung,s5pv210-jpeg.yaml @@ -0,0 +1,122 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/samsung,s5pv210-jpeg.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5PV210 and Exynos SoC JPEG codec + +maintainers: + - Jacek Anaszewski <jacek.anaszewski@gmail.com> + - Krzysztof Kozlowski <krzk@kernel.org> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + - Andrzej Pietrasiewicz <andrzejtp2010@gmail.com> + +properties: + compatible: + enum: + - samsung,s5pv210-jpeg + - samsung,exynos3250-jpeg + - samsung,exynos4210-jpeg + - samsung,exynos4212-jpeg + - samsung,exynos5420-jpeg + - samsung,exynos5433-jpeg + + clocks: + minItems: 1 + maxItems: 4 + + clock-names: + minItems: 1 + maxItems: 4 + + interrupts: + maxItems: 1 + + iommus: + maxItems: 1 + + power-domains: + maxItems: 1 + + reg: + maxItems: 1 + +required: + - compatible + - clocks + - clock-names + - interrupts + - reg + +allOf: + - if: + properties: + compatible: + contains: + enum: + - samsung,s5pv210-jpeg + - samsung,exynos4210-jpeg + - samsung,exynos4212-jpeg + - samsung,exynos5420-jpeg + then: + properties: + clocks: + maxItems: 1 + clock-names: + items: + - const: jpeg + + - if: + properties: + compatible: + contains: + enum: + - samsung,exynos3250-jpeg + then: + properties: + clocks: + minItems: 2 + maxItems: 2 + clock-names: + items: + - const: jpeg + - const: sclk + + - if: + properties: + compatible: + contains: + enum: + - samsung,exynos5433-jpeg + then: + properties: + clocks: + minItems: 4 + maxItems: 4 + clock-names: + items: + - const: pclk + - const: aclk + - const: aclk_xiu + - const: sclk + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos5433.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + codec@15020000 { + compatible = "samsung,exynos5433-jpeg"; + reg = <0x15020000 0x10000>; + interrupts = <GIC_SPI 411 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "pclk", "aclk", "aclk_xiu", "sclk"; + clocks = <&cmu_mscl CLK_PCLK_JPEG>, + <&cmu_mscl CLK_ACLK_JPEG>, + <&cmu_mscl CLK_ACLK_XIU_MSCLX>, + <&cmu_mscl CLK_SCLK_JPEG>; + iommus = <&sysmmu_jpeg>; + power-domains = <&pd_mscl>; + }; diff --git a/Documentation/devicetree/bindings/media/si4713.txt b/Documentation/devicetree/bindings/media/si4713.txt new file mode 100644 index 000000000..5ee5552d3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/si4713.txt @@ -0,0 +1,30 @@ +* Silicon Labs FM Radio transmitter + +The Silicon Labs Si4713 is an FM radio transmitter with receive power scan +supporting 76-108 MHz. It includes an RDS encoder and has both, a stereo-analog +and a digital interface, which supports I2S, left-justified and a custom +DSP-mode format. It is programmable through an I2C interface. + +Required Properties: +- compatible: Should contain "silabs,si4713" +- reg: the I2C address of the device + +Optional Properties: +- interrupts-extended: Interrupt specifier for the chips interrupt +- reset-gpios: GPIO specifier for the chips reset line +- vdd-supply: phandle for Vdd regulator +- vio-supply: phandle for Vio regulator + +Example: + +&i2c2 { + fmtx: si4713@63 { + compatible = "silabs,si4713"; + reg = <0x63>; + + interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */ + reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */ + vio-supply = <&vio>; + vdd-supply = <&vaux1>; + }; +}; diff --git a/Documentation/devicetree/bindings/media/silabs,si470x.yaml b/Documentation/devicetree/bindings/media/silabs,si470x.yaml new file mode 100644 index 000000000..db22b88fc --- /dev/null +++ b/Documentation/devicetree/bindings/media/silabs,si470x.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/silabs,si470x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Silicon Labs Si470x FM Radio Receiver + +maintainers: + - Hans Verkuil <hverkuil@kernel.org> + - Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> + +properties: + compatible: + const: silabs,si470x + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + fmradio@10 { + compatible = "silabs,si470x"; + reg = <0x10>; + interrupt-parent = <&gpj2>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpj2 5 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.yaml b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.yaml new file mode 100644 index 000000000..b7f6c87d0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.yaml @@ -0,0 +1,132 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Device Tree bindings for Synopsys DesignWare HDMI RX Controller + +--- +$id: http://devicetree.org/schemas/media/snps,dw-hdmi-rx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DesignWare HDMI RX Controller + +maintainers: + - Dmitry Osipenko <dmitry.osipenko@collabora.com> + +description: + Synopsys DesignWare HDMI Input Controller preset on RK3588 SoCs + allowing devices to receive and decode high-resolution video streams + from external sources like media players, cameras, laptops, etc. + +properties: + compatible: + items: + - const: rockchip,rk3588-hdmirx-ctrler + - const: snps,dw-hdmi-rx + + reg: + maxItems: 1 + + interrupts: + maxItems: 3 + + interrupt-names: + items: + - const: cec + - const: hdmi + - const: dma + + clocks: + maxItems: 7 + + clock-names: + items: + - const: aclk + - const: audio + - const: cr_para + - const: pclk + - const: ref + - const: hclk_s_hdmirx + - const: hclk_vo1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 4 + + reset-names: + items: + - const: axi + - const: apb + - const: ref + - const: biu + + memory-region: + maxItems: 1 + + hpd-gpios: + description: GPIO specifier for HPD. + maxItems: 1 + + rockchip,grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: + The phandle of the syscon node for the general register file + containing HDMIRX PHY status bits. + + rockchip,vo1-grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: + The phandle of the syscon node for the Video Output GRF register + to enable EDID transfer through SDAIN and SCLIN. + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + - clock-names + - power-domains + - resets + - pinctrl-0 + - hpd-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rockchip,rk3588-cru.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/power/rk3588-power.h> + #include <dt-bindings/reset/rockchip,rk3588-cru.h> + hdmi_receiver: hdmi-receiver@fdee0000 { + compatible = "rockchip,rk3588-hdmirx-ctrler", "snps,dw-hdmi-rx"; + reg = <0xfdee0000 0x6000>; + interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "cec", "hdmi", "dma"; + clocks = <&cru ACLK_HDMIRX>, + <&cru CLK_HDMIRX_AUD>, + <&cru CLK_CR_PARA>, + <&cru PCLK_HDMIRX>, + <&cru CLK_HDMIRX_REF>, + <&cru PCLK_S_HDMIRX>, + <&cru HCLK_VO1>; + clock-names = "aclk", + "audio", + "cr_para", + "pclk", + "ref", + "hclk_s_hdmirx", + "hclk_vo1"; + power-domains = <&power RK3588_PD_VO1>; + resets = <&cru SRST_A_HDMIRX>, <&cru SRST_P_HDMIRX>, + <&cru SRST_HDMIRX_REF>, <&cru SRST_A_HDMIRX_BIU>; + reset-names = "axi", "apb", "ref", "biu"; + memory-region = <&hdmi_receiver_cma>; + pinctrl-0 = <&hdmim1_rx_cec &hdmim1_rx_hpdin &hdmim1_rx_scl &hdmim1_rx_sda &hdmirx_5v_detection>; + pinctrl-names = "default"; + hpd-gpios = <&gpio1 22 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/media/spi/sony-cxd2880.txt b/Documentation/devicetree/bindings/media/spi/sony-cxd2880.txt new file mode 100644 index 000000000..98a72c0b3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/spi/sony-cxd2880.txt @@ -0,0 +1,18 @@ +Sony CXD2880 DVB-T2/T tuner + demodulator driver SPI adapter + +Required properties: +- compatible: Should be "sony,cxd2880". +- reg: SPI chip select number for the device. +- spi-max-frequency: Maximum bus speed, should be set to <55000000> (55MHz). + +Optional properties: +- vcc-supply: Optional phandle to the vcc regulator to power the adapter, + as described in the file ../regulator/regulator.txt + +Example: + +cxd2880@0 { + compatible = "sony,cxd2880"; + reg = <0>; /* CE0 */ + spi-max-frequency = <55000000>; /* 55MHz */ +}; diff --git a/Documentation/devicetree/bindings/media/st,st-delta.txt b/Documentation/devicetree/bindings/media/st,st-delta.txt new file mode 100644 index 000000000..a538ab30a --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,st-delta.txt @@ -0,0 +1,17 @@ +* STMicroelectronics DELTA multi-format video decoder + +Required properties: +- compatible: should be "st,st-delta". +- clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend on the SoC type. + See ../clock/clock-bindings.txt for details. +- clock-names: names of the clocks listed in clocks property in the same order. + +Example: + delta0 { + compatible = "st,st-delta"; + clock-names = "delta", "delta-st231", "delta-flash-promip"; + clocks = <&clk_s_c0_flexgen CLK_VID_DMU>, + <&clk_s_c0_flexgen CLK_ST231_DMU>, + <&clk_s_c0_flexgen CLK_FLASH_PROMIP>; + }; diff --git a/Documentation/devicetree/bindings/media/st,st-hva.txt b/Documentation/devicetree/bindings/media/st,st-hva.txt new file mode 100644 index 000000000..0d76174a1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,st-hva.txt @@ -0,0 +1,24 @@ +st-hva: multi-format video encoder for STMicroelectronics SoC. + +Required properties: +- compatible: should be "st,st-hva". +- reg: HVA physical address location and length, esram address location and + length. +- reg-names: names of the registers listed in registers property in the same + order. +- interrupts: HVA interrupt number. +- clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend on the SoC type. + See ../clock/clock-bindings.txt for details. +- clock-names: names of the clocks listed in clocks property in the same order. + +Example: + hva@8c85000{ + compatible = "st,st-hva"; + reg = <0x8c85000 0x400>, <0x6000000 0x40000>; + reg-names = "hva_registers", "hva_esram"; + interrupts = <GIC_SPI 58 IRQ_TYPE_NONE>, + <GIC_SPI 59 IRQ_TYPE_NONE>; + clock-names = "clk_hva"; + clocks = <&clk_s_c0_flexgen CLK_HVA>; + }; diff --git a/Documentation/devicetree/bindings/media/st,stih4xx.txt b/Documentation/devicetree/bindings/media/st,stih4xx.txt new file mode 100644 index 000000000..df655cd3a --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,stih4xx.txt @@ -0,0 +1,32 @@ +STMicroelectronics stih4xx platforms + +bdisp: 2D blitter for STMicroelectronics SoC. + +Required properties: +- compatible: should be "st,stih407-bdisp". +- reg: BDISP physical address location and length. +- interrupts: BDISP interrupt number. +- clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend on the SoC type. + See ../clocks/clock-bindings.txt for details. +- clock-names: names of the clocks listed in clocks property in the same order. + +Example: + + bdisp0:bdisp@9f10000 { + compatible = "st,stih407-bdisp"; + reg = <0x9f10000 0x1000>; + interrupts = <GIC_SPI 38 IRQ_TYPE_NONE>; + clock-names = "bdisp"; + clocks = <&clk_s_c0_flexgen CLK_IC_BDISP_0>; + }; + +Aliases: +Each BDISP should have a numbered alias in the aliases node, in the form of +bdispN, N = 0 or 1. + +Example: + + aliases { + bdisp0 = &bdisp0; + }; diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml new file mode 100644 index 000000000..7c2ddd277 --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/st,stm32-dcmi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32 Digital Camera Memory Interface (DCMI) + +maintainers: + - Hugues Fruchet <hugues.fruchet@foss.st.com> + +properties: + compatible: + const: st,stm32-dcmi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: mclk + + dmas: + minItems: 1 + maxItems: 2 + + dma-names: + items: + - const: tx + - const: mdma_tx + minItems: 1 + + resets: + maxItems: 1 + + access-controllers: + minItems: 1 + maxItems: 2 + + power-domains: + maxItems: 1 + + sram: + maxItems: 1 + description: + SRAM region which is used as temporary storage memory between DMA and + MDMA engines. + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + DCMI supports a single port node with parallel bus. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + enum: [5, 6] + default: 5 + + bus-width: + enum: [8, 10, 12, 14] + default: 8 + + allOf: + - if: + properties: + bus-type: + const: 6 + + then: + properties: + hsync-active: false + vsync-active: false + bus-width: + enum: [8] + + required: + - bus-type + - pclk-sample + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + - dmas + - dma-names + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/stm32mp1-clks.h> + #include <dt-bindings/media/video-interfaces.h> + #include <dt-bindings/reset/stm32mp1-resets.h> + + dcmi: dcmi@4c006000 { + compatible = "st,stm32-dcmi"; + reg = <0x4c006000 0x400>; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; + resets = <&rcc CAMITF_R>; + clocks = <&rcc DCMI>; + clock-names = "mclk"; + dmas = <&dmamux1 75 0x400 0x0d>; + dma-names = "tx"; + + port { + dcmi_0: endpoint { + remote-endpoint = <&ov5640_0>; + bus-type = <MEDIA_BUS_TYPE_PARALLEL>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmipp.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmipp.yaml new file mode 100644 index 000000000..162a0c526 --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmipp.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/st,stm32-dcmipp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32 DCMIPP Digital Camera Memory Interface Pixel Processor + +maintainers: + - Hugues Fruchet <hugues.fruchet@foss.st.com> + - Alain Volmat <alain.volmat@foss.st.com> + +properties: + compatible: + enum: + - st,stm32mp13-dcmipp + - st,stm32mp25-dcmipp + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: bus clock + - description: csi clock + minItems: 1 + + clock-names: + items: + - const: kclk + - const: mclk + minItems: 1 + + resets: + maxItems: 1 + + power-domains: + maxItems: 1 + + access-controllers: + minItems: 1 + maxItems: 2 + + port: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + DCMIPP supports a single port node with parallel bus. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-type: + enum: [4, 5, 6] + default: 5 + + bus-width: + enum: [8, 10, 12, 14] + default: 8 + + pclk-sample: true + hsync-active: true + vsync-active: true + +required: + - compatible + - reg + - interrupts + - clocks + - resets + - port + +allOf: + - if: + properties: + compatible: + contains: + enum: + - st,stm32mp13-dcmipp + then: + properties: + clocks: + maxItems: 1 + + clock-names: + maxItems: 1 + + port: + properties: + endpoint: + properties: + bus-type: + enum: [5, 6] + else: + properties: + clocks: + minItems: 2 + + clock-names: + minItems: 2 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/stm32mp13-clks.h> + #include <dt-bindings/reset/stm32mp13-resets.h> + dcmipp@5a000000 { + compatible = "st,stm32mp13-dcmipp"; + reg = <0x5a000000 0x400>; + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; + resets = <&rcc DCMIPP_R>; + clocks = <&rcc DCMIPP_K>; + + port { + endpoint { + remote-endpoint = <&mipid02_2>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <0>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/st,stm32-dma2d.yaml b/Documentation/devicetree/bindings/media/st,stm32-dma2d.yaml new file mode 100644 index 000000000..b9f7d84f3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,stm32-dma2d.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/st,stm32-dma2d.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32 Chrom-Art Accelerator DMA2D + +description: + Chrom-ART Accelerator(DMA2D), graphical hardware accelerator + enabling enhanced graphical user interface with minimum CPU load + + It can perform the following operations. + + - Filling a part or the whole of a destination image with a specific color. + - Copying a part or the whole of a source image into a part or the whole of + a destination image. + - Copying a part or the whole of a source image into a part or the whole of + a destination image with a pixel format conversion. + - Blending a part and/or two complete source images with different pixel + format and copy the result into a part or the whole of a destination image + with a different color format. (TODO) + +maintainers: + - Dillon Min <dillon.minfei@gmail.com> + +properties: + compatible: + const: st,stm32-dma2d + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: dma2d + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/stm32fx-clock.h> + #include <dt-bindings/mfd/stm32f4-rcc.h> + dma2d: dma2d@4002b000 { + compatible = "st,stm32-dma2d"; + reg = <0x4002b000 0xc00>; + interrupts = <90>; + resets = <&rcc STM32F4_AHB1_RESET(DMA2D)>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(DMA2D)>; + clock-names = "dma2d"; + }; + +... diff --git a/Documentation/devicetree/bindings/media/st,stm32mp25-csi.yaml b/Documentation/devicetree/bindings/media/st,stm32mp25-csi.yaml new file mode 100644 index 000000000..2ac7c9670 --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,stm32mp25-csi.yaml @@ -0,0 +1,127 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/st,stm32mp25-csi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32 CSI controller + +description: + The STM32 CSI controller, coupled with a D-PHY allows connecting a CSI-2 + based camera to the DCMIPP camera pipeline. + +maintainers: + - Alain Volmat <alain.volmat@foss.st.com> + +properties: + compatible: + enum: + - st,stm32mp25-csi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 3 + + clock-names: + items: + - const: pclk + - const: txesc + - const: csi2phy + + resets: + maxItems: 1 + + vdd-supply: + description: Digital core power supply (0.91V) + + vdda18-supply: + description: System analog power supply (1.8V) + + access-controllers: + minItems: 1 + maxItems: 2 + + power-domains: + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port node + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + items: + - const: 1 + - const: 2 + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Output port node + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/st,stm32mp25-rcc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/media/video-interfaces.h> + #include <dt-bindings/reset/st,stm32mp25-rcc.h> + csi@48020000 { + compatible = "st,stm32mp25-csi"; + reg = <0x48020000 0x2000>; + interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>; + resets = <&rcc CSI_R>; + clocks = <&rcc CK_KER_CSI>, <&rcc CK_KER_CSITXESC>, <&rcc CK_KER_CSIPHY>; + clock-names = "pclk", "txesc", "csi2phy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + endpoint { + remote-endpoint = <&imx335_ep>; + data-lanes = <1 2>; + }; + }; + + port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&dcmipp_0>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/st,stm32mp25-video-codec.yaml b/Documentation/devicetree/bindings/media/st,stm32mp25-video-codec.yaml new file mode 100644 index 000000000..73726c65c --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,stm32mp25-video-codec.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/st,stm32mp25-video-codec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32MP25 VDEC video decoder & VENC video encoder + +maintainers: + - Hugues Fruchet <hugues.fruchet@foss.st.com> + +description: + The STMicroelectronics STM32MP25 SOCs embeds a VDEC video hardware + decoder peripheral based on Verisilicon VC8000NanoD IP (former Hantro G1) + and a VENC video hardware encoder peripheral based on Verisilicon + VC8000NanoE IP (former Hantro H1). + +properties: + compatible: + enum: + - st,stm32mp25-vdec + - st,stm32mp25-venc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + access-controllers: + minItems: 1 + maxItems: 2 + +required: + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + video-codec@580d0000 { + compatible = "st,stm32mp25-vdec"; + reg = <0x580d0000 0x3c8>; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ck_icn_p_vdec>; + }; diff --git a/Documentation/devicetree/bindings/media/st-rc.txt b/Documentation/devicetree/bindings/media/st-rc.txt new file mode 100644 index 000000000..05c432d08 --- /dev/null +++ b/Documentation/devicetree/bindings/media/st-rc.txt @@ -0,0 +1,29 @@ +Device-Tree bindings for ST IRB IP + +Required properties: + - compatible: Should contain "st,comms-irb". + - reg: Base physical address of the controller and length of memory + mapped region. + - interrupts: interrupt-specifier for the sole interrupt generated by + the device. The interrupt specifier format depends on the interrupt + controller parent. + - rx-mode: can be "infrared" or "uhf". This property specifies the L1 + protocol used for receiving remote control signals. rx-mode should + be present iff the rx pins are wired up. + - tx-mode: should be "infrared". This property specifies the L1 + protocol used for transmitting remote control signals. tx-mode should + be present iff the tx pins are wired up. + +Optional properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure muxing + properly for IRB pins. + - clocks : phandle with clock-specifier pair for IRB. + +Example node: + + rc: rc@fe518000 { + compatible = "st,comms-irb"; + reg = <0xfe518000 0x234>; + interrupts = <0 203 0>; + rx-mode = "infrared"; + }; diff --git a/Documentation/devicetree/bindings/media/ti,cal.yaml b/Documentation/devicetree/bindings/media/ti,cal.yaml new file mode 100644 index 000000000..f1a940a11 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti,cal.yaml @@ -0,0 +1,177 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/ti,cal.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DRA72x CAMERA ADAPTATION LAYER (CAL) + +maintainers: + - Benoit Parrot <bparrot@ti.com> + +description: |- + The Camera Adaptation Layer (CAL) is a key component for image capture + applications. The capture module provides the system interface and the + processing capability to connect CSI2 image-sensor modules to the + DRA72x device. + + CAL supports 2 camera port nodes on MIPI bus. + +properties: + compatible: + enum: + # for DRA72 controllers + - ti,dra72-cal + # for DRA72 controllers pre ES2.0 + - ti,dra72-pre-es2-cal + # for DRA76 controllers + - ti,dra76-cal + # for AM654 controllers + - ti,am654-cal + + reg: + minItems: 2 + items: + - description: The CAL main register region + - description: The RX Core0 (DPHY0) register region + - description: The RX Core1 (DPHY1) register region + + reg-names: + minItems: 2 + items: + - const: cal_top + - const: cal_rx_core0 + - const: cal_rx_core1 + + interrupts: + maxItems: 1 + + ti,camerrx-control: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to device control module + - description: offset to the control_camerarx_core register + description: + phandle to the device control module and offset to the + control_camerarx_core register + + clocks: + maxItems: 1 + + clock-names: + const: fck + + power-domains: + description: + List of phandle and PM domain specifier as documented in + Documentation/devicetree/bindings/power/power_domain.txt + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: 'CSI2 Port #0' + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: 'CSI2 Port #1' + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - port@0 + +required: + - compatible + - reg + - reg-names + - interrupts + - ti,camerrx-control + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + cal: cal@4845b000 { + compatible = "ti,dra72-cal"; + reg = <0x4845B000 0x400>, + <0x4845B800 0x40>, + <0x4845B900 0x40>; + reg-names = "cal_top", + "cal_rx_core0", + "cal_rx_core1"; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; + ti,camerrx-control = <&scm_conf 0xE94>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + reg = <0>; + csi2_phy0: endpoint { + remote-endpoint = <&csi2_cam0>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; + }; + + i2c { + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + + camera-sensor@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + AVDD-supply = <®_2p8v>; + DOVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p5v>; + clocks = <&clk_ov5640_fixed>; + clock-names = "xclk"; + + port { + csi2_cam0: endpoint { + remote-endpoint = <&csi2_phy0>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt new file mode 100644 index 000000000..e47c7ccc5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt @@ -0,0 +1,106 @@ +Texas Instruments VPIF +---------------------- + +The TI Video Port InterFace (VPIF) is the primary component for video +capture and display on the DA850/AM18x family of TI DaVinci/Sitara +SoCs. + +TI Document reference: SPRUH82C, Chapter 35 +http://www.ti.com/lit/pdf/spruh82 + +Required properties: +- compatible: must be "ti,da850-vpif" +- reg: physical base address and length of the registers set for the device; +- interrupts: should contain IRQ line for the VPIF + +Video Capture: + +VPIF has a 16-bit parallel bus input, supporting 2 8-bit channels or a +single 16-bit channel. It should contain one or two port child nodes +with child 'endpoint' node. If there are two ports then port@0 must +describe the input and port@1 output channels. Please refer to the +bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example using 2 8-bit input channels, one of which is connected to an +I2C-connected TVP5147 decoder: + + vpif: vpif@217000 { + compatible = "ti,da850-vpif"; + reg = <0x217000 0x1000>; + interrupts = <92>; + + port@0 { + vpif_input_ch0: endpoint@0 { + reg = <0>; + bus-width = <8>; + remote-endpoint = <&composite_in>; + }; + + vpif_input_ch1: endpoint@1 { + reg = <1>; + bus-width = <8>; + data-shift = <8>; + }; + }; + + port@1 { + vpif_output_ch0: endpoint { + bus-width = <8>; + remote-endpoint = <&composite_out>; + }; + }; + }; + +[ ... ] + +&i2c0 { + + tvp5147@5d { + compatible = "ti,tvp5147"; + reg = <0x5d>; + + port { + composite_in: endpoint { + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + + /* VPIF channel 0 (lower 8-bits) */ + remote-endpoint = <&vpif_input_ch0>; + bus-width = <8>; + }; + }; + }; + + adv7343@2a { + compatible = "adi,adv7343"; + reg = <0x2a>; + + port { + composite_out: endpoint { + adi,dac-enable = <1 1 1>; + adi,sd-dac-enable = <1>; + + remote-endpoint = <&vpif_output_ch0>; + bus-width = <8>; + }; + }; + }; +}; + + +Alternatively, an example when the bus is configured as a single +16-bit input (e.g. for raw-capture mode): + + vpif: vpif@217000 { + compatible = "ti,da850-vpif"; + reg = <0x217000 0x1000>; + interrupts = <92>; + + port { + vpif_ch0: endpoint { + bus-width = <16>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/ti,j721e-csi2rx-shim.yaml b/Documentation/devicetree/bindings/media/ti,j721e-csi2rx-shim.yaml new file mode 100644 index 000000000..bf62998b0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti,j721e-csi2rx-shim.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/ti,j721e-csi2rx-shim.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TI J721E CSI2RX Shim + +description: | + The TI J721E CSI2RX Shim is a wrapper around Cadence CSI2RX bridge that + enables sending captured frames to memory over PSI-L DMA. In the J721E + Technical Reference Manual (SPRUIL1B) it is referred to as "SHIM" under the + CSI_RX_IF section. + +maintainers: + - Jai Luthra <jai.luthra@linux.dev> + +properties: + compatible: + const: ti,j721e-csi2rx-shim + + dmas: + minItems: 1 + maxItems: 32 + + dma-names: + minItems: 1 + items: + - const: rx0 + - const: rx1 + - const: rx2 + - const: rx3 + - const: rx4 + - const: rx5 + - const: rx6 + - const: rx7 + - const: rx8 + - const: rx9 + - const: rx10 + - const: rx11 + - const: rx12 + - const: rx13 + - const: rx14 + - const: rx15 + - const: rx16 + - const: rx17 + - const: rx18 + - const: rx19 + - const: rx20 + - const: rx21 + - const: rx22 + - const: rx23 + - const: rx24 + - const: rx25 + - const: rx26 + - const: rx27 + - const: rx28 + - const: rx29 + - const: rx30 + - const: rx31 + + reg: + maxItems: 1 + + power-domains: + maxItems: 1 + + ranges: true + + "#address-cells": true + + "#size-cells": true + +patternProperties: + "^csi-bridge@": + type: object + description: CSI2 bridge node. + $ref: cdns,csi2rx.yaml# + +required: + - compatible + - reg + - dmas + - dma-names + - power-domains + - ranges + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/soc/ti,sci_pm_domain.h> + + ti_csi2rx0: ticsi2rx@4500000 { + compatible = "ti,j721e-csi2rx-shim"; + dmas = <&main_udmap 0x4940>, <&main_udmap 0x4941>; + dma-names = "rx0", "rx1"; + reg = <0x4500000 0x1000>; + power-domains = <&k3_pds 26 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + cdns_csi2rx: csi-bridge@4504000 { + compatible = "ti,j721e-csi2rx", "cdns,csi2rx"; + reg = <0x4504000 0x1000>; + clocks = <&k3_clks 26 2>, <&k3_clks 26 0>, <&k3_clks 26 2>, + <&k3_clks 26 2>, <&k3_clks 26 3>, <&k3_clks 26 3>; + clock-names = "sys_clk", "p_clk", "pixel_if0_clk", + "pixel_if1_clk", "pixel_if2_clk", "pixel_if3_clk"; + phys = <&dphy0>; + phy-names = "dphy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + + reg = <0>; + + csi2rx0_in_sensor: endpoint { + remote-endpoint = <&csi2_cam0>; + bus-type = <4>; /* CSI2 DPHY. */ + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/ti,omap3isp.yaml b/Documentation/devicetree/bindings/media/ti,omap3isp.yaml new file mode 100644 index 000000000..7155fd3db --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti,omap3isp.yaml @@ -0,0 +1,189 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/ti,omap3isp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments OMAP 3 Image Signal Processor (ISP) + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + - Sakari Ailus <sakari.ailus@iki.fi> + +description: + The OMAP 3 ISP is an image signal processor present in OMAP 3 SoCs. + +properties: + compatible: + const: ti,omap3-isp + + reg: + items: + - description: Core ISP registers up to the end of the SBL block + - description: CSI PHYs and receivers registers + + interrupts: + maxItems: 1 + + iommus: + maxItems: 1 + + syscon: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to System Control Module + - description: register offset to Complex I/O or CSI-PHY register + description: + Phandle and register offset to the Complex I/O or CSI-PHY register + + ti,phy-type: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: + 0 - OMAP3ISP_PHY_TYPE_COMPLEX_IO (e.g. OMAP 3430) + 1 - OMAP3ISP_PHY_TYPE_CSIPHY (e.g. OMAP 3630) + + '#clock-cells': + const: 1 + description: + The ISP provides two external clocks, cam_xclka and cam_xclkb, + at indices 0 and 1 respectively. + + vdd-csiphy1-supply: + description: Voltage supply of the CSI-2 PHY 1 + + vdd-csiphy2-supply: + description: Voltage supply of the CSI-2 PHY 2 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: Parallel (CCDC) interface + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: | + CSIPHY1 interface: + OMAP 3630: CSI2C / CCP2B + OMAP 3430: CSI1 (CSIb) + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + lane-polarities: + minItems: 2 + maxItems: 3 + + data-lanes: + minItems: 1 + maxItems: 2 + items: + minimum: 1 + maximum: 3 + + clock-lanes: + minimum: 1 + maximum: 3 + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: | + CSIPHY2 interface: + OMAP 3630: CSI2A / CCP2B + OMAP 3430: CSI2 (CSIa) + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + lane-polarities: + minItems: 2 + maxItems: 3 + + data-lanes: + minItems: 1 + maxItems: 2 + items: + minimum: 1 + maximum: 3 + + clock-lanes: + minimum: 1 + maximum: 3 + +required: + - compatible + - reg + - interrupts + - iommus + - syscon + - ti,phy-type + - '#clock-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/media/omap3-isp.h> + + isp@480bc000 { + compatible = "ti,omap3-isp"; + reg = <0x480bc000 0x12fc>, + <0x480bd800 0x0600>; + interrupts = <24>; + iommus = <&mmu_isp>; + syscon = <&scm_conf 0x2f0>; + ti,phy-type = <OMAP3ISP_PHY_TYPE_CSIPHY>; + #clock-cells = <1>; + vdd-csiphy1-supply = <&vaux2>; + vdd-csiphy2-supply = <&vaux2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + parallel_ep: endpoint { + remote-endpoint = <¶llel>; + }; + }; + + port@1 { + reg = <1>; + csi1_ep: endpoint { + remote-endpoint = <&smia_1>; + clock-lanes = <1>; + data-lanes = <2>; + lane-polarities = <0 0>; + }; + }; + + port@2 { + reg = <2>; + csi2a_ep: endpoint { + remote-endpoint = <&smia_2>; + clock-lanes = <2>; + data-lanes = <1 3>; + lane-polarities = <1 1 1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/ti,vip.yaml b/Documentation/devicetree/bindings/media/ti,vip.yaml new file mode 100644 index 000000000..e30cc4615 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti,vip.yaml @@ -0,0 +1,152 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2025 Texas Instruments Incorporated - http://www.ti.com/ +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/ti,vip.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DRA7x Video Input Port (VIP) + +maintainers: + - Yemike Abhilash Chandra <y-abhilashchandra@ti.com> + +description: |- + Video Input Port (VIP) can be found on devices such as DRA7xx and + provides the system interface and the processing capability to + connect parallel image-sensor as well as BT.656/1120 capable encoder + chip to DRA7x device. + + Each VIP instance supports 2 independently configurable external + video input capture slices (Slice 0 and Slice 1) each providing + up to two video input ports (Port A and Port B). + +properties: + compatible: + enum: + - ti,dra7-vip + + reg: + maxItems: 1 + + interrupts: + items: + - description: IRQ index 0 is used for Slice0 interrupts + - description: IRQ index 1 is used for Slice1 interrupts + + ti,ctrl-module: + description: + Reference to the device control module that provides clock-edge + inversion control for VIP ports. These controls allow the + VIP to sample pixel data on the correct clock edge. + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + items: + - description: phandle to device control module + - description: offset to the CTRL_CORE_SMA_SW_1 register + - description: Bit field to slice 0 port A + - description: Bit field to slice 0 port B + - description: Bit field to slice 1 port A + - description: Bit field to slice 1 port B + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + patternProperties: + '^port@[0-3]$': + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: | + Each VIP instance supports 2 independently configurable external video + input capture slices (Slice 0 and Slice 1) each providing up to two video + input ports (Port A and Port B). These ports represent the following + port@0 -> Slice 0 Port A + port@1 -> Slice 0 Port B + port@2 -> Slice 1 Port A + port@3 -> Slice 1 Port B + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-width: + enum: [8, 16, 24] + default: 8 + +required: + - compatible + - reg + - interrupts + - ti,ctrl-module + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + video@48970000 { + compatible = "ti,dra7-vip"; + reg = <0x48970000 0x1000>; + interrupts = <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 392 IRQ_TYPE_LEVEL_HIGH>; + ti,ctrl-module = <&scm_conf 0x534 0x0 0x2 0x1 0x3>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + vin1a: port@0 { + reg = <0>; + + vin1a_ep: endpoint { + remote-endpoint = <&camera1>; + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + bus-width = <8>; + }; + }; + + vin1b: port@1 { + reg = <1>; + + vin1b_ep: endpoint { + remote-endpoint = <&camera2>; + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + bus-width = <8>; + }; + }; + + vin2a: port@2 { + reg = <2>; + + vin2a_ep: endpoint { + remote-endpoint = <&camera3>; + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + bus-width = <16>; + }; + }; + + vin2b: port@3 { + reg = <3>; + + vin2b_ep: endpoint { + remote-endpoint = <&camera4>; + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + bus-width = <8>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/ti,vpe.yaml b/Documentation/devicetree/bindings/media/ti,vpe.yaml new file mode 100644 index 000000000..7fa8a367e --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti,vpe.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/ti,vpe.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DRA7x Video Processing Engine (VPE) + +maintainers: + - Benoit Parrot <bparrot@ti.com> + +description: |- + The Video Processing Engine (VPE) is a key component for image post + processing applications. VPE consist of a single memory to memory + path which can perform chroma up/down sampling, deinterlacing, + scaling and color space conversion. + +properties: + compatible: + const: ti,dra7-vpe + + reg: + items: + - description: The VPE main register region + - description: Scaler (SC) register region + - description: Color Space Conversion (CSC) register region + - description: Video Port Direct Memory Access (VPDMA) register region + + reg-names: + items: + - const: vpe_top + - const: sc + - const: csc + - const: vpdma + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - reg-names + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + vpe: vpe@489d0000 { + compatible = "ti,dra7-vpe"; + reg = <0x489d0000 0x120>, + <0x489d0700 0x80>, + <0x489d5700 0x18>, + <0x489dd000 0x400>; + reg-names = "vpe_top", + "sc", + "csc", + "vpdma"; + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + }; + +... diff --git a/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt b/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt new file mode 100644 index 000000000..3932e7665 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt @@ -0,0 +1,61 @@ +Texas Instruments AM437x CAMERA (VPFE) +-------------------------------------- + +The Video Processing Front End (VPFE) is a key component for image capture +applications. The capture module provides the system interface and the +processing capability to connect RAW image-sensor modules and video decoders +to the AM437x device. + +Required properties: +- compatible: must be "ti,am437x-vpfe" +- reg: physical base address and length of the registers set for the device; +- interrupts: should contain IRQ line for the VPFE; +- ti,am437x-vpfe-interface: can be one of the following, + 0 - Raw Bayer Interface. + 1 - 8 Bit BT656 Interface. + 2 - 10 Bit BT656 Interface. + 3 - YCbCr 8 Bit Interface. + 4 - YCbCr 16 Bit Interface. + +VPFE supports a single port node with parallel bus. It should contain one +'port' child node with child 'endpoint' node. Please refer to the bindings +defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + vpfe: vpfe@f0034000 { + compatible = "ti,am437x-vpfe"; + reg = <0x48328000 0x2000>; + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&vpfe_pins_default>; + pinctrl-1 = <&vpfe_pins_sleep>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + vpfe0_ep: endpoint { + remote-endpoint = <&ov2659_1>; + ti,am437x-vpfe-interface = <0>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + }; + + i2c1: i2c@4802a000 { + + ov2659@30 { + compatible = "ti,ov2659"; + reg = <0x30>; + + port { + ov2659_1: endpoint { + remote-endpoint = <&vpfe0_ep>; + bus-width = <8>; + mclk-frequency = <12000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/video-interface-devices.yaml b/Documentation/devicetree/bindings/media/video-interface-devices.yaml new file mode 100644 index 000000000..a81d2a155 --- /dev/null +++ b/Documentation/devicetree/bindings/media/video-interface-devices.yaml @@ -0,0 +1,410 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/video-interface-devices.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common Properties for Video Receiver and Transmitter Devices + +maintainers: + - Jacopo Mondi <jacopo@jmondi.org> + - Sakari Ailus <sakari.ailus@linux.intel.com> + +properties: + flash-leds: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + An array of phandles, each referring to a flash LED, a sub-node of the LED + driver device node. + + leds: + minItems: 1 + maxItems: 1 + + led-names: + enum: + - privacy + + lens-focus: + $ref: /schemas/types.yaml#/definitions/phandle + description: + A phandle to the node of the focus lens controller. + + rotation: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 90, 180, 270 ] + description: | + The camera rotation is expressed as the angular difference in degrees + between two reference systems, one relative to the camera module, and one + defined on the external world scene to be captured when projected on the + image sensor pixel array. + + A camera sensor has a 2-dimensional reference system 'Rc' defined by its + pixel array read-out order. The origin is set to the first pixel being + read out, the X-axis points along the column read-out direction towards + the last columns, and the Y-axis along the row read-out direction towards + the last row. + + A typical example for a sensor with a 2592x1944 pixel array matrix + observed from the front is: + + 2591 X-axis 0 + <------------------------+ 0 + .......... ... ..........! + .......... ... ..........! Y-axis + ... ! + .......... ... ..........! + .......... ... ..........! 1943 + V + + The external world scene reference system 'Rs' is a 2-dimensional + reference system on the focal plane of the camera module. The origin is + placed on the top-left corner of the visible scene, the X-axis points + towards the right, and the Y-axis points towards the bottom of the scene. + The top, bottom, left and right directions are intentionally not defined + and depend on the environment in which the camera is used. + + A typical example of a (very common) picture of a shark swimming from left + to right, as seen from the camera, is: + + 0 X-axis + 0 +-------------------------------------> + ! + ! + ! + ! |\____)\___ + ! ) _____ __`< + ! |/ )/ + ! + ! + ! + V + Y-axis + + with the reference system 'Rs' placed on the camera focal plane: + + ¸.·˙! + ¸.·˙ ! + _ ¸.·˙ ! + +-/ \-+¸.·˙ ! + | (o) | ! Camera focal plane + +-----+˙·.¸ ! + ˙·.¸ ! + ˙·.¸ ! + ˙·.¸! + + When projected on the sensor's pixel array, the image and the associated + reference system 'Rs' are typically (but not always) inverted, due to the + camera module's lens optical inversion effect. + + Assuming the above represented scene of the swimming shark, the lens + inversion projects the scene and its reference system onto the sensor + pixel array, seen from the front of the camera sensor, as follows: + + Y-axis + ^ + ! + ! + ! + ! |\_____)\__ + ! ) ____ ___.< + ! |/ )/ + ! + ! + ! + 0 +-------------------------------------> + 0 X-axis + + Note the shark being upside-down. + + The resulting projected reference system is named 'Rp'. + + The camera rotation property is then defined as the angular difference in + the counter-clockwise direction between the camera reference system 'Rc' + and the projected scene reference system 'Rp'. It is expressed in degrees + as a number in the range [0, 360[. + + Examples + + 0 degrees camera rotation: + + Y-Rp + ^ + Y-Rc ! + ^ ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! 0 +-------------------------------------> + ! 0 X-Rp + 0 +-------------------------------------> + 0 X-Rc + + X-Rc 0 + <------------------------------------+ 0 + X-Rp 0 ! + <------------------------------------+ 0 ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! V + ! Y-Rc + V + Y-Rp + + 90 degrees camera rotation: + + 0 Y-Rc + 0 +--------------------> + ! Y-Rp + ! ^ + ! ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! 0 +-------------------------------------> + ! 0 X-Rp + ! + ! + ! + ! + V + X-Rc + + 180 degrees camera rotation: + + 0 + <------------------------------------+ 0 + X-Rc ! + Y-Rp ! + ^ ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! V + ! Y-Rc + 0 +-------------------------------------> + 0 X-Rp + + 270 degrees camera rotation: + + 0 Y-Rc + 0 +--------------------> + ! 0 + ! <-----------------------------------+ 0 + ! X-Rp ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! ! + ! V + ! Y-Rp + ! + ! + ! + ! + V + X-Rc + + Example one - Webcam + + A camera module installed on the user facing part of a laptop screen + casing used for video calls. The captured images are meant to be displayed + in landscape mode (width > height) on the laptop screen. + + The camera is typically mounted upside-down to compensate the lens optical + inversion effect: + + Y-Rp + Y-Rc ^ + ^ ! + ! ! + ! ! |\_____)\__ + ! ! ) ____ ___.< + ! ! |/ )/ + ! ! + ! ! + ! ! + ! 0 +-------------------------------------> + ! 0 X-Rp + 0 +-------------------------------------> + 0 X-Rc + + The two reference systems are aligned, the resulting camera rotation is + 0 degrees, no rotation correction needs to be applied to the resulting + image once captured to memory buffers to correctly display it to users: + + +--------------------------------------+ + ! ! + ! ! + ! ! + ! |\____)\___ ! + ! ) _____ __`< ! + ! |/ )/ ! + ! ! + ! ! + ! ! + +--------------------------------------+ + + If the camera sensor is not mounted upside-down to compensate for the lens + optical inversion, the two reference systems will not be aligned, with + 'Rp' being rotated 180 degrees relatively to 'Rc': + + X-Rc 0 + <------------------------------------+ 0 + ! + Y-Rp ! + ^ ! + ! ! + ! |\_____)\__ ! + ! ) ____ ___.< ! + ! |/ )/ ! + ! ! + ! ! + ! V + ! Y-Rc + 0 +-------------------------------------> + 0 X-Rp + + The image once captured to memory will then be rotated by 180 degrees: + + +--------------------------------------+ + ! ! + ! ! + ! ! + ! __/(_____/| ! + ! >.___ ____ ( ! + ! \( \| ! + ! ! + ! ! + ! ! + +--------------------------------------+ + + A software rotation correction of 180 degrees should be applied to + correctly display the image: + + +--------------------------------------+ + ! ! + ! ! + ! ! + ! |\____)\___ ! + ! ) _____ __`< ! + ! |/ )/ ! + ! ! + ! ! + ! ! + +--------------------------------------+ + + Example two - Phone camera + + A camera installed on the back side of a mobile device facing away from + the user. The captured images are meant to be displayed in portrait mode + (height > width) to match the device screen orientation and the device + usage orientation used when taking the picture. + + The camera sensor is typically mounted with its pixel array longer side + aligned to the device longer side, upside-down mounted to compensate for + the lens optical inversion effect: + + 0 Y-Rc + 0 +--------------------> + ! Y-Rp + ! ^ + ! ! + ! ! + ! ! + ! ! |\_____)\__ + ! ! ) ____ ___.< + ! ! |/ )/ + ! ! + ! ! + ! ! + ! 0 +-------------------------------------> + ! 0 X-Rp + ! + ! + ! + ! + V + X-Rc + + The two reference systems are not aligned and the 'Rp' reference system is + rotated by 90 degrees in the counter-clockwise direction relatively to the + 'Rc' reference system. + + The image once captured to memory will be rotated: + + +-------------------------------------+ + | _ _ | + | \ / | + | | | | + | | | | + | | > | + | < | | + | | | | + | . | + | V | + +-------------------------------------+ + + A correction of 90 degrees in counter-clockwise direction has to be + applied to correctly display the image in portrait mode on the device + screen: + + +--------------------+ + | | + | | + | | + | | + | | + | | + | |\____)\___ | + | ) _____ __`< | + | |/ )/ | + | | + | | + | | + | | + | | + +--------------------+ + + orientation: + description: + The orientation of a device (typically an image sensor or a flash LED) + describing its mounting position relative to the usage orientation of the + system where the device is installed on. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + # Front. The device is mounted on the front facing side of the system. For + # mobile devices such as smartphones, tablets and laptops the front side + # is the user facing side. + - 0 + # Back. The device is mounted on the back side of the system, which is + # defined as the opposite side of the front facing one. + - 1 + # External. The device is not attached directly to the system but is + # attached in a way that allows it to move freely. + - 2 + +additionalProperties: true + +... diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt new file mode 100644 index 000000000..8fcf5f52b --- /dev/null +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -0,0 +1 @@ +This file has moved to video-interfaces.yaml and video-interface-devices.yaml. diff --git a/Documentation/devicetree/bindings/media/video-interfaces.yaml b/Documentation/devicetree/bindings/media/video-interfaces.yaml new file mode 100644 index 000000000..6ed4695ca --- /dev/null +++ b/Documentation/devicetree/bindings/media/video-interfaces.yaml @@ -0,0 +1,241 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/video-interfaces.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common Properties for Video Receiver and Transmitter Interface Endpoints + +maintainers: + - Sakari Ailus <sakari.ailus@linux.intel.com> + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: | + Video data pipelines usually consist of external devices, e.g. camera sensors, + controlled over an I2C, SPI or UART bus, and SoC internal IP blocks, including + video DMA engines and video data processors. + + SoC internal blocks are described by DT nodes, placed similarly to other SoC + blocks. External devices are represented as child nodes of their respective + bus controller nodes, e.g. I2C. + + Data interfaces on all video devices are described by their child 'port' nodes. + Configuration of a port depends on other devices participating in the data + transfer and is described by 'endpoint' subnodes. + + device { + ... + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + ... + endpoint@0 { ... }; + endpoint@1 { ... }; + }; + port@1 { ... }; + }; + }; + + If a port can be configured to work with more than one remote device on the same + bus, an 'endpoint' child node must be provided for each of them. If more than + one port is present in a device node or there is more than one endpoint at a + port, or port node needs to be associated with a selected hardware interface, + a common scheme using '#address-cells', '#size-cells' and 'reg' properties is + used. + + All 'port' nodes can be grouped under optional 'ports' node, which allows to + specify #address-cells, #size-cells properties independently for the 'port' + and 'endpoint' nodes and any child device nodes a device might have. + + Two 'endpoint' nodes are linked with each other through their 'remote-endpoint' + phandles. An endpoint subnode of a device contains all properties needed for + configuration of this device for data exchange with other device. In most + cases properties at the peer 'endpoint' nodes will be identical, however they + might need to be different when there is any signal modifications on the bus + between two devices, e.g. there are logic signal inverters on the lines. + + It is allowed for multiple endpoints at a port to be active simultaneously, + where supported by a device. For example, in case where a data interface of + a device is partitioned into multiple data busses, e.g. 16-bit input port + divided into two separate ITU-R BT.656 8-bit busses. In such case bus-width + and data-shift properties can be used to assign physical data lines to each + endpoint node (logical bus). + + Documenting bindings for devices + -------------------------------- + + All required and optional bindings the device supports shall be explicitly + documented in device DT binding documentation. This also includes port and + endpoint nodes for the device, including unit-addresses and reg properties + where relevant. + +allOf: + - $ref: /schemas/graph.yaml#/$defs/endpoint-base + +properties: + slave-mode: + type: boolean + description: + Indicates that the link is run in slave mode. The default when this + property is not specified is master mode. In the slave mode horizontal and + vertical synchronization signals are provided to the slave device (data + source) by the master device (data sink). In the master mode the data + source device is also the source of the synchronization signals. + + bus-type: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 1 # MIPI CSI-2 C-PHY + - 2 # MIPI CSI1 + - 3 # CCP2 + - 4 # MIPI CSI-2 D-PHY + - 5 # Parallel + - 6 # BT.656 + - 7 # DPI + description: + Data bus type. See include/dt-bindings/media/video-interfaces.h. + + bus-width: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 64 + description: + Number of data lines actively used, valid for the parallel busses. + + data-shift: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 64 + description: + On the parallel data busses, if bus-width is used to specify the number of + data lines, data-shift can be used to specify which data lines are used, + e.g. "bus-width=<8>; data-shift=<2>;" means, that lines 9:2 are used. + + hsync-active: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1 ] + description: + Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. + + vsync-active: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1 ] + description: + Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. Note, + that if HSYNC and VSYNC polarities are not specified, embedded + synchronization may be required, where supported. + + data-active: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1 ] + description: + Similar to HSYNC and VSYNC, specifies data line polarity. + + data-enable-active: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1 ] + description: + Similar to HSYNC and VSYNC, specifies the data enable signal polarity. + + field-even-active: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1 ] + description: + Field signal level during the even field data transmission. + + pclk-sample: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2 ] + description: + Sample data on falling (0), rising (1) or both (2) edges of the pixel + clock signal. + + sync-on-green-active: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1 ] + description: + Active state of Sync-on-green (SoG) signal, 0/1 for LOW/HIGH respectively. + + data-lanes: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + uniqueItems: true + items: + # Assume up to 9 physical lane indices + maximum: 8 + description: + An array of physical data lane indexes. Position of an entry determines + the logical lane number, while the value of an entry indicates physical + lane, e.g. for 2-lane MIPI CSI-2 bus we could have "data-lanes = <1 2>;", + assuming the clock lane is on hardware lane 0. If the hardware does not + support lane reordering, monotonically incremented values shall be used + from 0 or 1 onwards, depending on whether or not there is also a clock + lane. This property is valid for serial busses only (e.g. MIPI CSI-2). + + clock-lanes: + $ref: /schemas/types.yaml#/definitions/uint32 + # Assume up to 9 physical lane indices + maximum: 8 + description: + Physical clock lane index. Position of an entry determines the logical + lane number, while the value of an entry indicates physical lane, e.g. for + a MIPI CSI-2 bus we could have "clock-lanes = <0>;", which places the + clock lane on hardware lane 0. This property is valid for serial busses + only (e.g. MIPI CSI-2). + + clock-noncontinuous: + type: boolean + description: + Allow MIPI CSI-2 non-continuous clock mode. + + link-frequencies: + $ref: /schemas/types.yaml#/definitions/uint64-array + description: + Allowed data bus frequencies. For MIPI CSI-2, for instance, this is the + actual frequency of the bus, not bits per clock per lane value. An array + of 64-bit unsigned integers. + + lane-polarities: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 9 + items: + enum: [ 0, 1 ] + description: + An array of polarities of the lanes starting from the clock lane and + followed by the data lanes in the same order as in data-lanes. Valid + values are 0 (normal) and 1 (inverted). The length of the array should be + the combined length of data-lanes and clock-lanes properties. If the + lane-polarities property is omitted, the value must be interpreted as 0 + (normal). This property is valid for serial busses only. + + line-orders: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + enum: + - 0 # ABC + - 1 # ACB + - 2 # BAC + - 3 # BCA + - 4 # CAB + - 5 # CBA + description: + An array of line orders of the CSI-2 C-PHY data lanes. The order of the + lanes are the same as in data-lanes property. Valid values are 0-5 as + defined in the MIPI Discovery and Configuration (DisCo) Specification for + Imaging. The length of the array must be the same length as the + data-lanes property. If the line-orders property is omitted, the value + shall be interpreted as 0 (ABC). This property is valid for CSI-2 C-PHY + busses only. See include/dt-bindings/media/video-interfaces.h. + + strobe: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1 ] + description: + Whether the clock signal is used as clock (0) or strobe (1). Used with + CCP2, for instance. + +additionalProperties: true diff --git a/Documentation/devicetree/bindings/media/video-mux.yaml b/Documentation/devicetree/bindings/media/video-mux.yaml new file mode 100644 index 000000000..2f28a7dad --- /dev/null +++ b/Documentation/devicetree/bindings/media/video-mux.yaml @@ -0,0 +1,106 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/video-mux.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Video Multiplexer + +maintainers: + - Sakari Ailus <sakari.ailus@linux.intel.com> + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: + Video multiplexers allow to select between multiple input ports. Video + received on the active input port is passed through to the output port. Muxes + described by this binding are controlled by a multiplexer controller. + +properties: + compatible: + const: video-mux + + mux-controls: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + patternProperties: + '^port@': + $ref: /schemas/graph.yaml#/properties/port + + required: + - port@0 + - port@1 + - port@2 + +patternProperties: + '^port@': + $ref: /schemas/graph.yaml#/properties/port + description: + At least three port nodes containing endpoints connecting to the source + and sink devices according to of_graph bindings. The last port is the + output port, all others are inputs. + +required: + - compatible + - mux-controls + +oneOf: + - required: + - ports + - required: + - port@0 + - port@1 + - port@2 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + mux: mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + + mux-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + }; + + video-mux { + compatible = "video-mux"; + mux-controls = <&mux>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + mux_in0: endpoint { + remote-endpoint = <&video_source0_out>; + }; + }; + + port@1 { + reg = <1>; + + mux_in1: endpoint { + remote-endpoint = <&video_source1_out>; + }; + }; + + port@2 { + reg = <2>; + + mux_out: endpoint { + remote-endpoint = <&capture_interface_in>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/xilinx/video.txt b/Documentation/devicetree/bindings/media/xilinx/video.txt new file mode 100644 index 000000000..d0335ca0c --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/video.txt @@ -0,0 +1,35 @@ +DT bindings for Xilinx video IP cores +------------------------------------- + +Xilinx video IP cores process video streams by acting as video sinks and/or +sources. They are connected by links through their input and output ports, +creating a video pipeline. + +Each video IP core is represented by an AMBA bus child node in the device +tree using bindings documented in this directory. Connections between the IP +cores are represented as defined in ../video-interfaces.txt. + +The whole pipeline is represented by an AMBA bus child node in the device +tree using bindings documented in ./xlnx,video.txt. + +Common properties +----------------- + +The following properties are common to all Xilinx video IP cores. + +- xlnx,video-format: This property represents a video format transmitted on an + AXI bus between video IP cores, using its VF code as defined in "AXI4-Stream + Video IP and System Design Guide" [UG934]. How the format relates to the IP + core is described in the IP core bindings documentation. + +- xlnx,video-width: This property qualifies the video format with the sample + width expressed as a number of bits per pixel component. All components must + use the same width. + +- xlnx,cfa-pattern: When the video format is set to Mono/Sensor, this property + describes the sensor's color filter array pattern. Supported values are + "bggr", "gbrg", "grbg", "rggb" and "mono". If not specified, the pattern + defaults to "mono". + + +[UG934] https://www.xilinx.com/support/documentation/ip_documentation/axi_videoip/v1_0/ug934_axi_videoIP.pdf diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml new file mode 100644 index 000000000..43daf837f --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml @@ -0,0 +1,209 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/xilinx/xlnx,csi2rxss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx MIPI CSI-2 Receiver Subsystem + +maintainers: + - Vishal Sagar <vishal.sagar@amd.com> + +description: | + The Xilinx MIPI CSI-2 Receiver Subsystem is used to capture MIPI CSI-2 + traffic from compliant camera sensors and send the output as AXI4 Stream + video data for image processing. + The subsystem consists of a MIPI D-PHY in slave mode which captures the + data packets. This is passed along the MIPI CSI-2 Rx IP which extracts the + packet data. The optional Video Format Bridge (VFB) converts this data to + AXI4 Stream video data. + For more details, please refer to PG232 Xilinx MIPI CSI-2 Receiver Subsystem. + Please note that this bindings includes only the MIPI CSI-2 Rx controller + and Video Format Bridge and not D-PHY. + +properties: + compatible: + items: + - enum: + - xlnx,mipi-csi2-rx-subsystem-5.0 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + description: List of clock specifiers + items: + - description: AXI Lite clock + - description: Video clock + + clock-names: + items: + - const: lite_aclk + - const: video_aclk + + xlnx,csi-pxl-format: + description: | + This denotes the CSI Data type selected in hw design. + Packets other than this data type (except for RAW8 and + User defined data types) will be filtered out. + Possible values are as below - + 0x1e - YUV4228B + 0x1f - YUV42210B + 0x20 - RGB444 + 0x21 - RGB555 + 0x22 - RGB565 + 0x23 - RGB666 + 0x24 - RGB888 + 0x28 - RAW6 + 0x29 - RAW7 + 0x2a - RAW8 + 0x2b - RAW10 + 0x2c - RAW12 + 0x2d - RAW14 + 0x2e - RAW16 + 0x2f - RAW20 + $ref: /schemas/types.yaml#/definitions/uint32 + oneOf: + - minimum: 0x1e + maximum: 0x24 + - minimum: 0x28 + maximum: 0x2f + + xlnx,vfb: + type: boolean + description: Present when Video Format Bridge is enabled in IP configuration + + xlnx,en-csi-v2-0: + type: boolean + description: Present if CSI v2 is enabled in IP configuration. + + xlnx,en-vcx: + type: boolean + description: | + When present, there are maximum 16 virtual channels, else only 4. + + xlnx,en-active-lanes: + type: boolean + description: | + Present if the number of active lanes can be re-configured at + runtime in the Protocol Configuration Register. Otherwise all lanes, + as set in IP configuration, are always active. + + video-reset-gpios: + description: Optional specifier for a GPIO that asserts video_aresetn. + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + description: | + Input / sink port node, single endpoint describing the + CSI-2 transmitter. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: | + This is required only in the sink port 0 endpoint which + connects to MIPI CSI-2 source like sensor. + The possible values are - + 1 - For 1 lane enabled in IP. + 1 2 - For 2 lanes enabled in IP. + 1 2 3 - For 3 lanes enabled in IP. + 1 2 3 4 - For 4 lanes enabled in IP. + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - data-lanes + + unevaluatedProperties: false + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: | + Output / source port node, endpoint describing modules + connected the CSI-2 receiver. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - ports + +allOf: + - if: + required: + - xlnx,vfb + then: + required: + - xlnx,csi-pxl-format + else: + properties: + xlnx,csi-pxl-format: false + + - if: + not: + required: + - xlnx,en-csi-v2-0 + then: + properties: + xlnx,en-vcx: false + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + xcsi2rxss_1: csi2rx@a0020000 { + compatible = "xlnx,mipi-csi2-rx-subsystem-5.0"; + reg = <0xa0020000 0x10000>; + interrupt-parent = <&gic>; + interrupts = <0 95 4>; + xlnx,csi-pxl-format = <0x2a>; + xlnx,vfb; + xlnx,en-active-lanes; + xlnx,en-csi-v2-0; + xlnx,en-vcx; + clock-names = "lite_aclk", "video_aclk"; + clocks = <&misc_clk_0>, <&misc_clk_1>; + video-reset-gpios = <&gpio 86 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + /* Sink port */ + reg = <0>; + csiss_in: endpoint { + data-lanes = <1 2 3 4>; + /* MIPI CSI-2 Camera handle */ + remote-endpoint = <&camera_out>; + }; + }; + port@1 { + /* Source port */ + reg = <1>; + csiss_out: endpoint { + remote-endpoint = <&vproc_in>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt new file mode 100644 index 000000000..2aed3b4a6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt @@ -0,0 +1,33 @@ +Xilinx Video Timing Controller (VTC) +------------------------------------ + +The Video Timing Controller is a general purpose video timing generator and +detector. + +Required properties: + + - compatible: Must be "xlnx,v-tc-6.1". + + - reg: Physical base address and length of the registers set for the device. + + - clocks: Must contain a clock specifier for the VTC core and timing + interfaces clock. + +Optional properties: + + - xlnx,detector: The VTC has a timing detector + - xlnx,generator: The VTC has a timing generator + + At least one of the xlnx,detector and xlnx,generator properties must be + specified. + + +Example: + + vtc: vtc@43c40000 { + compatible = "xlnx,v-tc-6.1"; + reg = <0x43c40000 0x10000>; + + clocks = <&clkc 15>; + xlnx,generator; + }; diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt new file mode 100644 index 000000000..439351ab2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt @@ -0,0 +1,71 @@ +Xilinx Video Test Pattern Generator (TPG) +----------------------------------------- + +Required properties: + +- compatible: Must contain at least one of + + "xlnx,v-tpg-5.0" (TPG version 5.0) + "xlnx,v-tpg-6.0" (TPG version 6.0) + + TPG versions backward-compatible with previous versions should list all + compatible versions in the newer to older order. + +- reg: Physical base address and length of the registers set for the device. + +- clocks: Reference to the video core clock. + +- xlnx,video-format, xlnx,video-width: Video format and width, as defined in + video.txt. + +- port: Video port, using the DT bindings defined in ../video-interfaces.txt. + The TPG has a single output port numbered 0. + +Optional properties: + +- xlnx,vtc: A phandle referencing the Video Timing Controller that generates + video timings for the TPG test patterns. + +- timing-gpios: Specifier for a GPIO that controls the timing mux at the TPG + input. The GPIO active level corresponds to the selection of VTC-generated + video timings. + +The xlnx,vtc and timing-gpios properties are mandatory when the TPG is +synthesized with two ports and forbidden when synthesized with one port. + +Example: + + tpg_0: tpg@40050000 { + compatible = "xlnx,v-tpg-6.0", "xlnx,v-tpg-5.0"; + reg = <0x40050000 0x10000>; + clocks = <&clkc 15>; + + xlnx,vtc = <&vtc_3>; + timing-gpios = <&ps7_gpio_0 55 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + xlnx,video-format = <XVIP_VF_YUV_422>; + xlnx,video-width = <8>; + + tpg_in: endpoint { + remote-endpoint = <&adv7611_out>; + }; + }; + port@1 { + reg = <1>; + + xlnx,video-format = <XVIP_VF_YUV_422>; + xlnx,video-width = <8>; + + tpg1_out: endpoint { + remote-endpoint = <&switch_in0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt new file mode 100644 index 000000000..5a0227023 --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt @@ -0,0 +1,55 @@ +Xilinx Video IP Pipeline (VIPP) +------------------------------- + +General concept +--------------- + +Xilinx video IP pipeline processes video streams through one or more Xilinx +video IP cores. Each video IP core is represented as documented in video.txt +and IP core specific documentation, xlnx,v-*.txt, in this directory. The DT +node of the VIPP represents as a top level node of the pipeline and defines +mappings between DMAs and the video IP cores. + +Required properties: + +- compatible: Must be "xlnx,video". + +- dmas, dma-names: List of one DMA specifier and identifier string (as defined + in Documentation/devicetree/bindings/dma/dma.txt) per port. Each port + requires a DMA channel with the identifier string set to "port" followed by + the port index. + +- ports: Video port, using the DT bindings defined in ../video-interfaces.txt. + +Required port properties: + +- direction: should be either "input" or "output" depending on the direction + of stream. + +Example: + + video_cap { + compatible = "xlnx,video"; + dmas = <&vdma_1 1>, <&vdma_3 1>; + dma-names = "port0", "port1"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + direction = "input"; + vcap0_in0: endpoint { + remote-endpoint = <&scaler0_out>; + }; + }; + port@1 { + reg = <1>; + direction = "input"; + vcap0_in1: endpoint { + remote-endpoint = <&switch_out1>; + }; + }; + }; + }; |