drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validationgrafted

amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and
uses the first encoding that validates. YCbCr 4:4:4 is listed before
RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the
"color format" property is left at AUTO, even though RGB fits the same
link.

That contradicts the documented AUTO behaviour for HDMI in enum
drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when
the bandwidth is not available or the mode is 4:2:0-only), which the
amdgpu implementation of the property also describes. It also leaves
the "Broadcast RGB" property without effect on such sinks, since the
quantization range it selects only applies to RGB output.

Try RGB first. The mask still holds every encoding the sink supports,
so a mode that cannot carry RGB falls back exactly as before.

For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced
through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI
sink that advertised it.

Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation")
Suggested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Assisted-by: Claude Code:claude-fable-5-1
Signed-off-by: Adrian Betschart <adrian.betschart@cinemaone.ch>
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7)

1 files changed, 36 insertions, 0 deletions

diff --git a/usr/initramfs_data.S b/usr/initramfs_data.S
new file mode 100644
index 000000000..e92fb59b3
--- /dev/null
+++ b/usr/initramfs_data.S
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+  initramfs_data includes the compressed binary that is the
+  filesystem used for early user space.
+  Note: Older versions of "as" (prior to binutils 2.11.90.0.23
+  released on 2001-07-14) did not support .incbin.
+  If you are forced to use older binutils than that then the
+  following trick can be applied to create the resulting binary:
+
+
+  ld -m elf_i386  --format binary --oformat elf32-i386 -r \
+  -T initramfs_data.scr initramfs_data.cpio.gz -o initramfs_data.o
+   ld -m elf_i386  -r -o built-in.a initramfs_data.o
+
+  For including the .init.ramfs sections, see include/asm-generic/vmlinux.lds.
+
+  The above example is for i386 - the parameters vary from architectures.
+  Eventually look up LDFLAGS_BLOB in an older version of the
+  arch/$(ARCH)/Makefile to see the flags used before .incbin was introduced.
+
+  Using .incbin has the advantage over ld that the correct flags are set
+  in the ELF header, as required by certain architectures.
+*/
+
+.section .init.ramfs,"a"
+__irf_start:
+.incbin "usr/initramfs_inc_data"
+__irf_end:
+.section .init.ramfs.info,"a"
+.globl __initramfs_size
+__initramfs_size:
+#ifdef CONFIG_64BIT
+	.quad __irf_end - __irf_start
+#else
+	.long __irf_end - __irf_start
+#endif