Merge tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlgrafted

Pull pin control updates from Linus Walleij:
 "Core changes:

   - Use the non-blocking mux_state_try_select() in the generic MUX pin
     control back-end

   - Free pin maps on pinctrl_generic_to_map() failure in the core
     helpers

  New hardware pin control:

   - Qualcomm Maili TLMM SoC, PMG1110 PMIC, and Eliza LPASS LPI TLMM SoC
     (this is for the low power audio, LPASS = Low Power Audio SubSystem
     portions)

   - Upboard support on top of the Intel pin controller

   - Apple T6030 and T6031 support (just compatible strings)

   - Samsung Exynos 8855 SoC

   - Mediatek MT6858 SoC

   - Rockchip RK3308B and RV1106 SoCs

   - Airoha EN7523 and AN7563 SoCs

  Improvements:

   - Qualcomm TLMM GPIOs are unconditionally marked as wakeup capable

   - Qualcomm improvements on top of the Qualcomm PDC (power domain
     controller) irqchip improvements from tglx:s tree

   - Qualcomm IPQ806x and IPQ9650 non-urgent pin grop fixups

   - The NPCM8xx driver has been put into shape fixing many pin and
     group definitions

   - Some non-urgent Tegra 264 pin assignments are fixed up

   - Some non-urgent fixups to Airoha AN7581 and AN7583 registers and
     pin assignments, missing features etc"

* tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (130 commits)
  dt-bindings: pinctrl: Convert TI DA850 pupd to DT schema
  pinctrl: meson: sync some modify from A4
  pinctrl: meson: a4: Add input enable pin configuration
  pinctrl: realtek: rtd1625: remove unused group name spdif_sel
  pinctrl: realtek: rtd1625: fix base_bit for VE4 GPIO 13
  dt-bindings: pinctrl: microchip,pic32mzda-pinctrl: Convert to DT schema
  Revert "Merge branch 'ib-rsk7204' into devel"
  pinctrl: rockchip: Add RV1106 pinctrl support
  dt-bindings: pinctrl: rockchip: Add RV1106 compatible
  pinctrl: rockchip: Decode drive strength in the get function
  pinctrl: fix PINCTRL_GENERIC_MUX not always being selectable
  pinctrl: airoha: add support of an7563 SoC
  dt-bindings: pinctrl: airoha: add support of an7563 pin controller
  pinctrl: airoha: try to find chip scu node by phandle first
  pinctrl: airoha: add support of en7523 SoC
  dt-bindings: pinctrl: airoha: add support of en7523 pin controller
  pinctrl: airoha: an7583: add support for olt pinmux
  pinctrl: airoha: an7583: add support for pon_alt pinmux
  pinctrl: airoha: an7583: add support for npu_uart pinmux
  dt-bindings: pinctrl: airoha: an7583: add missed features
  ...

1 files changed, 58 insertions, 0 deletions

diff --git a/net/hsr/Kconfig b/net/hsr/Kconfig
new file mode 100644
index 000000000..fcacdf4f0
--- /dev/null
+++ b/net/hsr/Kconfig
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# IEC 62439-3 High-availability Seamless Redundancy
+#
+
+config HSR
+	tristate "High-availability Seamless Redundancy (HSR & PRP)"
+	help
+	  This enables IEC 62439 defined High-availability Seamless
+	  Redundancy (HSR) and Parallel Redundancy Protocol (PRP).
+
+	  If you say Y here, then your Linux box will be able to act as a
+	  DANH ("Doubly attached node implementing HSR") or DANP ("Doubly
+	  attached node implementing PRP"). For this to work, your Linux box
+	  needs (at least) two physical Ethernet interfaces.
+
+	  For DANH, it must be connected as a node in a ring network together
+	  with other HSR capable nodes. All Ethernet frames sent over the HSR
+	  device will be sent in both directions on the ring (over both slave
+	  ports), giving a redundant, instant fail-over network. Each HSR node
+	  in the ring acts like a bridge for HSR frames, but filters frames
+	  that have been forwarded earlier.
+
+	  For DANP, it must be connected as a node connecting to two
+	  separate networks over the two slave interfaces. Like HSR, Ethernet
+	  frames sent over the PRP device will be sent to both networks giving
+	  a redundant, instant fail-over network. Unlike HSR, PRP networks
+	  can have Singly Attached Nodes (SAN) such as PC, printer, bridges
+	  etc and will be able to communicate with DANP nodes.
+
+	  This code is a "best effort" to comply with the HSR standard as
+	  described in IEC 62439-3:2010 (HSRv0) and IEC 62439-3:2012 (HSRv1),
+	  and PRP standard described in IEC 62439-4:2012 (PRP), but no
+	  compliancy tests have been made. Use iproute2 to select the protocol
+	  you would like to use.
+
+	  You need to perform any and all necessary tests yourself before
+	  relying on this code in a safety critical system!
+
+	  If unsure, say N.
+
+if HSR
+
+config PRP_DUP_DISCARD_KUNIT_TEST
+	tristate "PRP duplicate discard KUnit tests" if !KUNIT_ALL_TESTS
+	depends on KUNIT
+	default KUNIT_ALL_TESTS
+	help
+	  Covers the PRP duplicate discard algorithm.
+	  Only useful for kernel devs running KUnit test harness and are not
+	  for inclusion into a production build.
+
+	  For more information on KUnit and unit tests in general please refer
+	  to the KUnit documentation in Documentation/dev-tools/kunit/.
+
+	  If unsure, say N.
+
+endif