selftests/bpf: Test packet range of pointers sharing an idgrafted

Add tests where two packet pointers share an id and tightening one
pointer's umax from its var_off would put it less than their constant
distance from the other's umax: with an index & 0x38 capped at 50, the
base pointer keeps umax 50, so the pointer 8 bytes further on must keep
umax 58, even though its known bits allow at most 56.

These refused a valid program or accepted an out-of-bounds access before
the fix:

- check the advanced copy, load through the base: valid, was refused;
- check the base, load the byte at base + 1 through a copy advanced by
  8: was accepted;
- check base + 4, load 4 bytes at base + 2 through base + 8: reads two
  bytes past the checked range, was accepted;
- the same as the second with data_meta pointers checked against data:
  was accepted.

These pass with and without the fix and cover nearby paths:

- subtract an unknown scalar from a checked pointer and load below it
  (the range is kept across a new id);
- reach a load through two paths whose checks cover 8 and 7 bytes after
  the loaded pointer; the second path must not be pruned by the first;
- spill a copy of a pointer, check the pointer, fill the copy and load
  one byte past the checked range: the load is refused, and the copy
  has the range of the check.

Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20261001145255.855630-2-alexei.starovoitov@gmail.com
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>

1 files changed, 36 insertions, 0 deletions

diff --git a/drivers/usb/musb/Makefile b/drivers/usb/musb/Makefile
new file mode 100644
index 000000000..5dccf0e45
--- /dev/null
+++ b/drivers/usb/musb/Makefile
@@ -0,0 +1,36 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# for USB OTG silicon based on Mentor Graphics INVENTRA designs
+#
+
+# define_trace.h needs to know how to find our header
+CFLAGS_musb_trace.o	:= -I$(src)
+
+obj-$(CONFIG_USB_MUSB_HDRC) += musb_hdrc.o
+
+musb_hdrc-y := musb_core.o musb_trace.o
+
+musb_hdrc-$(CONFIG_USB_MUSB_HOST)$(CONFIG_USB_MUSB_DUAL_ROLE) += musb_virthub.o musb_host.o
+musb_hdrc-$(CONFIG_USB_MUSB_GADGET)$(CONFIG_USB_MUSB_DUAL_ROLE) += musb_gadget_ep0.o musb_gadget.o
+musb_hdrc-$(CONFIG_DEBUG_FS)			+= musb_debugfs.o
+
+# Hardware Glue Layer
+obj-$(CONFIG_USB_MUSB_OMAP2PLUS)		+= omap2430.o
+obj-$(CONFIG_USB_MUSB_DSPS)			+= musb_dsps.o
+obj-$(CONFIG_USB_MUSB_TUSB6010)			+= tusb6010.o
+obj-$(CONFIG_USB_MUSB_DA8XX)			+= da8xx.o
+obj-$(CONFIG_USB_MUSB_UX500)			+= ux500.o
+obj-$(CONFIG_USB_MUSB_JZ4740)			+= jz4740.o
+obj-$(CONFIG_USB_MUSB_SUNXI)			+= sunxi.o
+obj-$(CONFIG_USB_MUSB_MEDIATEK)      		+= mediatek.o
+obj-$(CONFIG_USB_MUSB_POLARFIRE_SOC)		+= mpfs.o
+
+# the kconfig must guarantee that only one of the
+# possible I/O schemes will be enabled at a time ...
+# PIO only, or DMA (several potential schemes).
+# though PIO is always there to back up DMA, and for ep0
+
+musb_hdrc-$(CONFIG_USB_INVENTRA_DMA)		+= musbhsdma.o
+musb_hdrc-$(CONFIG_USB_TUSB_OMAP_DMA)		+= tusb6010_omap.o
+musb_hdrc-$(CONFIG_USB_UX500_DMA)		+= ux500_dma.o
+musb_hdrc-$(CONFIG_USB_TI_CPPI41_DMA)		+= musb_cppi41.o