virtio_blk: set the zone write granularitygrafted

virtblk_read_zoned_limits() reads the write granularity that the device
reports in virtio_blk_zoned_characteristics and assigns it to the
physical block size and to io_min, but never to the limit that is named
after it. queue_limits.zone_write_granularity is left at zero, so
blk_validate_zoned_limits() raises it to the logical block size:

	if (lim->zone_write_granularity < lim->logical_block_size)
		lim->zone_write_granularity = lim->logical_block_size;

A device that reports a granularity coarser than its logical block size,
which is what the field exists to express, therefore has it silently
reduced. A 512e host managed disk passed through to a guest reports a
logical block size of 512 and a write granularity of 4096, and the guest
ends up with a zone write granularity of 512.

bio_split_alignment() returns lim->zone_write_granularity if it is non-zero
and bio_split_io_at() may split a bio with as per bio_split_alignment().
This can real to the write getting rejected by the host drive, as the write
is not aligned to the physical block size.

zonefs also takes its block size from bdev_zone_write_granularity(), so it
would incorrectly use 512 on a disk that requires 4096.

sd_zbc_read_zones() sets the limit from the physical block size for the
same reason. NVMe ZNS and null_blk leave it unset, but the fallback
gives the right answer for them, as their write granularity is the
logical block size. virtio carries a separate value that may exceed it.

Set the zone write granularity from the value that the device reports.

Fixes: 95bfec41bd3d ("virtio-blk: add support for zoned block devices")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://patch.msgid.link/20260918140641.2031075-2-cassel@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

1 files changed, 190 insertions, 0 deletions

diff --git a/drivers/usb/misc/ehset.c b/drivers/usb/misc/ehset.c
new file mode 100644
index 000000000..36b6e9fa7
--- /dev/null
+++ b/drivers/usb/misc/ehset.c
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2010-2013, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/usb.h>
+#include <linux/usb/ch11.h>
+
+#define TEST_SE0_NAK_PID			0x0101
+#define TEST_J_PID				0x0102
+#define TEST_K_PID				0x0103
+#define TEST_PACKET_PID				0x0104
+#define TEST_HS_HOST_PORT_SUSPEND_RESUME	0x0106
+#define TEST_SINGLE_STEP_GET_DEV_DESC		0x0107
+#define TEST_SINGLE_STEP_SET_FEATURE		0x0108
+
+extern const struct usb_device_id *usb_device_match_id(struct usb_device *udev,
+						const struct usb_device_id *id);
+
+/*
+ * A list of USB hubs which requires to disable the power
+ * to the port before starting the testing procedures.
+ */
+static const struct usb_device_id ehset_hub_list[] = {
+	{ USB_DEVICE(0x0424, 0x4502) },
+	{ USB_DEVICE(0x0424, 0x4913) },
+	{ USB_DEVICE(0x0451, 0x8027) },
+	{ }
+};
+
+static int ehset_prepare_port_for_testing(struct usb_device *hub_udev, u16 portnum)
+{
+	int ret = 0;
+
+	/*
+	 * The USB2.0 spec chapter 11.24.2.13 says that the USB port which is
+	 * going under test needs to be put in suspend before sending the
+	 * test command. Most hubs don't enforce this precondition, but there
+	 * are some hubs which needs to disable the power to the port before
+	 * starting the test.
+	 */
+	if (usb_device_match_id(hub_udev, ehset_hub_list)) {
+		ret = usb_control_msg_send(hub_udev, 0, USB_REQ_CLEAR_FEATURE,
+					   USB_RT_PORT, USB_PORT_FEAT_ENABLE,
+					   portnum, NULL, 0, 1000, GFP_KERNEL);
+		/*
+		 * Wait for the port to be disabled. It's an arbitrary value
+		 * which worked every time.
+		 */
+		msleep(100);
+	} else {
+		/*
+		 * For the hubs which are compliant with the spec,
+		 * put the port in SUSPEND.
+		 */
+		ret = usb_control_msg_send(hub_udev, 0, USB_REQ_SET_FEATURE,
+					   USB_RT_PORT, USB_PORT_FEAT_SUSPEND,
+					   portnum, NULL, 0, 1000, GFP_KERNEL);
+	}
+	return ret;
+}
+
+static int ehset_probe(struct usb_interface *intf,
+		       const struct usb_device_id *id)
+{
+	int ret = -EINVAL;
+	struct usb_device *dev = interface_to_usbdev(intf);
+	struct usb_device *hub_udev = dev->parent;
+	struct usb_device_descriptor buf;
+	u8 portnum = dev->portnum;
+	u16 test_pid = le16_to_cpu(dev->descriptor.idProduct);
+
+	switch (test_pid) {
+	case TEST_SE0_NAK_PID:
+		ret = ehset_prepare_port_for_testing(hub_udev, portnum);
+		if (ret < 0)
+			break;
+		ret = usb_control_msg_send(hub_udev, 0, USB_REQ_SET_FEATURE,
+					   USB_RT_PORT, USB_PORT_FEAT_TEST,
+					   (USB_TEST_SE0_NAK << 8) | portnum,
+					   NULL, 0, 1000, GFP_KERNEL);
+		break;
+	case TEST_J_PID:
+		ret = ehset_prepare_port_for_testing(hub_udev, portnum);
+		if (ret < 0)
+			break;
+		ret = usb_control_msg_send(hub_udev, 0, USB_REQ_SET_FEATURE,
+					   USB_RT_PORT, USB_PORT_FEAT_TEST,
+					   (USB_TEST_J << 8) | portnum, NULL, 0,
+					   1000, GFP_KERNEL);
+		break;
+	case TEST_K_PID:
+		ret = ehset_prepare_port_for_testing(hub_udev, portnum);
+		if (ret < 0)
+			break;
+		ret = usb_control_msg_send(hub_udev, 0, USB_REQ_SET_FEATURE,
+					   USB_RT_PORT, USB_PORT_FEAT_TEST,
+					   (USB_TEST_K << 8) | portnum, NULL, 0,
+					   1000, GFP_KERNEL);
+		break;
+	case TEST_PACKET_PID:
+		ret = ehset_prepare_port_for_testing(hub_udev, portnum);
+		if (ret < 0)
+			break;
+		ret = usb_control_msg_send(hub_udev, 0, USB_REQ_SET_FEATURE,
+					   USB_RT_PORT, USB_PORT_FEAT_TEST,
+					   (USB_TEST_PACKET << 8) | portnum,
+					   NULL, 0, 1000, GFP_KERNEL);
+		break;
+	case TEST_HS_HOST_PORT_SUSPEND_RESUME:
+		/* Test: wait for 15secs -> suspend -> 15secs delay -> resume */
+		msleep(15 * 1000);
+		ret = usb_control_msg_send(hub_udev, 0, USB_REQ_SET_FEATURE,
+					   USB_RT_PORT, USB_PORT_FEAT_SUSPEND,
+					   portnum, NULL, 0, 1000, GFP_KERNEL);
+		if (ret < 0)
+			break;
+
+		msleep(15 * 1000);
+		ret = usb_control_msg_send(hub_udev, 0, USB_REQ_CLEAR_FEATURE,
+					   USB_RT_PORT, USB_PORT_FEAT_SUSPEND,
+					   portnum, NULL, 0, 1000, GFP_KERNEL);
+		break;
+	case TEST_SINGLE_STEP_GET_DEV_DESC:
+		/* Test: wait for 15secs -> GetDescriptor request */
+		msleep(15 * 1000);
+
+		ret = usb_control_msg_recv(dev, 0, USB_REQ_GET_DESCRIPTOR,
+					   USB_DIR_IN, USB_DT_DEVICE << 8, 0,
+					   &buf, USB_DT_DEVICE_SIZE,
+					   USB_CTRL_GET_TIMEOUT, GFP_KERNEL);
+		break;
+	case TEST_SINGLE_STEP_SET_FEATURE:
+		/*
+		 * GetDescriptor SETUP request -> 15secs delay -> IN & STATUS
+		 *
+		 * Note, this test is only supported on root hubs since the
+		 * SetPortFeature handling can only be done inside the HCD's
+		 * hub_control callback function.
+		 */
+		if (hub_udev != dev->bus->root_hub) {
+			dev_err(&intf->dev, "SINGLE_STEP_SET_FEATURE test only supported on root hub\n");
+			break;
+		}
+
+		ret = usb_control_msg_send(hub_udev, 0, USB_REQ_SET_FEATURE,
+					   USB_RT_PORT, USB_PORT_FEAT_TEST,
+					   (6 << 8) | portnum, NULL, 0,
+					   60 * 1000, GFP_KERNEL);
+
+		break;
+	default:
+		dev_err(&intf->dev, "%s: unsupported PID: 0x%x\n",
+			__func__, test_pid);
+	}
+
+	return ret;
+}
+
+static void ehset_disconnect(struct usb_interface *intf)
+{
+}
+
+static const struct usb_device_id ehset_id_table[] = {
+	{ USB_DEVICE(0x1a0a, TEST_SE0_NAK_PID) },
+	{ USB_DEVICE(0x1a0a, TEST_J_PID) },
+	{ USB_DEVICE(0x1a0a, TEST_K_PID) },
+	{ USB_DEVICE(0x1a0a, TEST_PACKET_PID) },
+	{ USB_DEVICE(0x1a0a, TEST_HS_HOST_PORT_SUSPEND_RESUME) },
+	{ USB_DEVICE(0x1a0a, TEST_SINGLE_STEP_GET_DEV_DESC) },
+	{ USB_DEVICE(0x1a0a, TEST_SINGLE_STEP_SET_FEATURE) },
+	{ }			/* Terminating entry */
+};
+MODULE_DEVICE_TABLE(usb, ehset_id_table);
+
+static struct usb_driver ehset_driver = {
+	.name =		"usb_ehset_test",
+	.probe =	ehset_probe,
+	.disconnect =	ehset_disconnect,
+	.id_table =	ehset_id_table,
+};
+
+module_usb_driver(ehset_driver);
+
+MODULE_DESCRIPTION("USB Driver for EHSET Test Fixture");
+MODULE_LICENSE("GPL v2");