openrisc: fix arbitrary kernel memory access via or1k_atomic syscallgrafted

sys_or1k_atomic() (syscall 244 in the "or1k" ABI) takes two user
pointers, v1 and v2, and swaps the words they point to in hand-written
assembly.

    l.lwz   r29,0(r4)
    l.lwz   r27,0(r5)
    l.sw    0(r4),r27
    l.sw    0(r5),r29

The pointers are not checked with access_ok(). The four memory
accesses also have no exception table entries.

A caller passes a kernel address as either pointer, and the syscall
reads from and writes to it directly.

This gives an unprivileged process a kernel read/write primitive. It
overwrites kernel data such as the sys_call_table, gaining code
execution in kernel context.

Check both pointers before entering the critical section. Add fixups
for the four memory accesses so faults on valid but unmapped user
addresses return -EFAULT.

[shorne@gmail.com: fix comment style]
Fixes: 9d02a4283e9c ("OpenRISC: Boot code")
Cc: stable@vger.kernel.org
Signed-off-by: Ali Ahmet Memis <ali@iusegentoo.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>

1 files changed, 51 insertions, 0 deletions

diff --git a/drivers/usb/common/Kconfig b/drivers/usb/common/Kconfig
new file mode 100644
index 000000000..b85662243
--- /dev/null
+++ b/drivers/usb/common/Kconfig
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: GPL-2.0
+
+config USB_COMMON
+	tristate
+
+
+config USB_LED_TRIG
+	bool "USB LED Triggers"
+	depends on LEDS_CLASS && USB_COMMON && LEDS_TRIGGERS
+	help
+	  This option adds LED triggers for USB host and/or gadget activity.
+
+	  Say Y here if you are working on a system with led-class supported
+	  LEDs and you want to use them as activity indicators for USB host or
+	  gadget.
+
+config USB_ULPI_BUS
+	tristate "USB ULPI PHY interface support"
+	select USB_COMMON
+	help
+	  UTMI+ Low Pin Interface (ULPI) is specification for a commonly used
+	  USB 2.0 PHY interface. The ULPI specification defines a standard set
+	  of registers that can be used to detect the vendor and product which
+	  allows ULPI to be handled as a bus. This module is the driver for that
+	  bus.
+
+	  The ULPI interfaces (the buses) are registered by the drivers for USB
+	  controllers which support ULPI register access and have ULPI PHY
+	  attached to them. The ULPI PHY drivers themselves are normal PHY
+	  drivers.
+
+	  ULPI PHYs provide often functions such as ADP sensing/probing (OTG
+	  protocol) and USB charger detection.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called ulpi.
+
+config USB_CONN_GPIO
+	tristate "USB GPIO Based Connection Detection Driver"
+	depends on GPIOLIB
+	select USB_ROLE_SWITCH
+	select POWER_SUPPLY
+	help
+	  The driver supports USB role switch between host and device via GPIO
+	  based USB cable detection, used typically if an input GPIO is used
+	  to detect USB ID pin, and another input GPIO may be also used to detect
+	  Vbus pin at the same time, it also can be used to enable/disable
+	  device if an input GPIO is only used to detect Vbus pin.
+
+	  To compile the driver as a module, choose M here: the module will
+	  be called usb-conn-gpio.ko