selftests/bpf: Reject graph kptr use after RCU unlockgrafted

Add a sleepable verifier test that loads a graph-node local kptr in an
explicit RCU read-side critical section, then passes its node to
bpf_rbtree_remove() after the section ends.

Before the verifier fix, the stale NON_OWN_REF flag makes the node look like
a live borrowed reference and the program is accepted. After the fix, the
pointer is demoted without NON_OWN_REF and the graph kfunc argument is
rejected.

Also exercise a graph kptr loaded while a spin lock provides implicit RCU
protection. The pointer must be invalidated when the lock is released, which
guards the required ordering between non-owning-reference invalidation and
RCU demotion.

Update the existing fault-protected load test state description. The
post-unlock pointer no longer carries NON_OWN_REF, but remains readable
because the load is rewritten to use BPF_PROBE_MEM.

Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20260904084325.52250-7-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

1 files changed, 51 insertions, 0 deletions

diff --git a/drivers/usb/common/Kconfig b/drivers/usb/common/Kconfig
new file mode 100644
index 000000000..b85662243
--- /dev/null
+++ b/drivers/usb/common/Kconfig
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: GPL-2.0
+
+config USB_COMMON
+	tristate
+
+
+config USB_LED_TRIG
+	bool "USB LED Triggers"
+	depends on LEDS_CLASS && USB_COMMON && LEDS_TRIGGERS
+	help
+	  This option adds LED triggers for USB host and/or gadget activity.
+
+	  Say Y here if you are working on a system with led-class supported
+	  LEDs and you want to use them as activity indicators for USB host or
+	  gadget.
+
+config USB_ULPI_BUS
+	tristate "USB ULPI PHY interface support"
+	select USB_COMMON
+	help
+	  UTMI+ Low Pin Interface (ULPI) is specification for a commonly used
+	  USB 2.0 PHY interface. The ULPI specification defines a standard set
+	  of registers that can be used to detect the vendor and product which
+	  allows ULPI to be handled as a bus. This module is the driver for that
+	  bus.
+
+	  The ULPI interfaces (the buses) are registered by the drivers for USB
+	  controllers which support ULPI register access and have ULPI PHY
+	  attached to them. The ULPI PHY drivers themselves are normal PHY
+	  drivers.
+
+	  ULPI PHYs provide often functions such as ADP sensing/probing (OTG
+	  protocol) and USB charger detection.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called ulpi.
+
+config USB_CONN_GPIO
+	tristate "USB GPIO Based Connection Detection Driver"
+	depends on GPIOLIB
+	select USB_ROLE_SWITCH
+	select POWER_SUPPLY
+	help
+	  The driver supports USB role switch between host and device via GPIO
+	  based USB cable detection, used typically if an input GPIO is used
+	  to detect USB ID pin, and another input GPIO may be also used to detect
+	  Vbus pin at the same time, it also can be used to enable/disable
+	  device if an input GPIO is only used to detect Vbus pin.
+
+	  To compile the driver as a module, choose M here: the module will
+	  be called usb-conn-gpio.ko