Merge tag 'io_uring-7.3-20261002' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linuxgrafted

Pull io_uring fixes from Jens Axboe:

 - Fix a task_work add use-after-free with SQPOLL.

   The sqpoll thread could pop and complete the last request while
   io_req_normal_work_add() was still looking at them after the mpscq
   push.

   Use the same approach as DEFER_TASKRUN to protect from that, holding
   an RCU read lock across the add, and have exit wait for an RCU grace
   period for SQPOLL rings as well.

 - CQE32 ring fixes: correct the free entry check for 32b CQEs, zero the
   big_cqe for aux CQEs, and only post the dummy skip CQE on CQE_MIXED
   rings

 - Mark the source filter table as COW when cloning bpf filters, so
   registering another filter on the source doesn't modify the shared
   table in place

 - Initialize the task context before running the BPF loop

 - Requeue zcrx multishot receives stopped by a local resource

 - End a TX_TIMESTAMP multishot cmd when the CQ is full (lollipopkit)

* tag 'io_uring-7.3-20261002' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
  io_uring: fix task_work add use-after-free with SQPOLL
  io_uring/cmd_net: end TX_TIMESTAMP multishot when the CQ is full
  io_uring/zcrx: requeue multishot receives stopped by a local resource
  io_uring: initialize task context before running the BPF loop
  io_uring: zero big_cqe for aux CQEs on CQE32 rings
  io_uring: fix free entry check for 32b CQEs on CQE32 rings
  io_uring: only post the dummy skip CQE on CQE_MIXED rings
  io_uring/bpf_filter: mark source as COW when cloning filters

1 files changed, 51 insertions, 0 deletions

diff --git a/drivers/usb/common/Kconfig b/drivers/usb/common/Kconfig
new file mode 100644
index 000000000..b85662243
--- /dev/null
+++ b/drivers/usb/common/Kconfig
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: GPL-2.0
+
+config USB_COMMON
+	tristate
+
+
+config USB_LED_TRIG
+	bool "USB LED Triggers"
+	depends on LEDS_CLASS && USB_COMMON && LEDS_TRIGGERS
+	help
+	  This option adds LED triggers for USB host and/or gadget activity.
+
+	  Say Y here if you are working on a system with led-class supported
+	  LEDs and you want to use them as activity indicators for USB host or
+	  gadget.
+
+config USB_ULPI_BUS
+	tristate "USB ULPI PHY interface support"
+	select USB_COMMON
+	help
+	  UTMI+ Low Pin Interface (ULPI) is specification for a commonly used
+	  USB 2.0 PHY interface. The ULPI specification defines a standard set
+	  of registers that can be used to detect the vendor and product which
+	  allows ULPI to be handled as a bus. This module is the driver for that
+	  bus.
+
+	  The ULPI interfaces (the buses) are registered by the drivers for USB
+	  controllers which support ULPI register access and have ULPI PHY
+	  attached to them. The ULPI PHY drivers themselves are normal PHY
+	  drivers.
+
+	  ULPI PHYs provide often functions such as ADP sensing/probing (OTG
+	  protocol) and USB charger detection.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called ulpi.
+
+config USB_CONN_GPIO
+	tristate "USB GPIO Based Connection Detection Driver"
+	depends on GPIOLIB
+	select USB_ROLE_SWITCH
+	select POWER_SUPPLY
+	help
+	  The driver supports USB role switch between host and device via GPIO
+	  based USB cable detection, used typically if an input GPIO is used
+	  to detect USB ID pin, and another input GPIO may be also used to detect
+	  Vbus pin at the same time, it also can be used to enable/disable
+	  device if an input GPIO is only used to detect Vbus pin.
+
+	  To compile the driver as a module, choose M here: the module will
+	  be called usb-conn-gpio.ko