sched/cache: Keep nr_pref_llc_running in the runnable domain, to fix LLC mis-scheduling buggrafted

alb_break_llc() decides whether to break LLC preference during active
load balance. It does so by testing that every runnable fair task on the
source rq prefers its LLC:

	env->src_rq->nr_pref_llc_running == env->src_rq->cfs.h_nr_runnable

But the two counters cover different sets. nr_pref_llc_running is updated
in account_llc_enqueue()/account_llc_dequeue(), next to cfs_rq->nr_queued,
so it follows queued tasks. h_nr_runnable is updated in set_delayed()/
clear_delayed() and drops delay-dequeued tasks.

So under DELAY_DEQUEUE, a preferring task that goes to sleep stays counted
in nr_pref_llc_running while h_nr_runnable falls. The equality then breaks,
alb_break_llc() returns false, and active balance is free to pull a task
off its preferred LLC. Active balance only moves runnable tasks, and this
is the only LLC check it consults: once the stopper runs, LBF_ACTIVE_LB
skips the per-task test in can_migrate_task(). The runnable set is the one
we want.

Fix it on the counter side. A task should be counted in
nr_pref_llc_running exactly while it is both queued on its preferred LLC
(pref_llc_queued) and runnable (!sched_delayed). Define that membership
once in task_pref_llc_runnable(), and adjust the counter only through
pref_llc_running_inc()/pref_llc_running_dec() from the four sites that
change either input: account_llc_enqueue(), account_llc_dequeue(),
set_delayed() and clear_delayed(). Gating every update on the same
predicate keeps the delay, wake and dequeue paths from double-counting
or underflowing; see the comments at those sites for the ordering.

nr_llc_running and sd->llc_counts are not touched and stay on queued
semantics.

Fixes: 714059f79ff0 ("sched/cache: Handle moving single tasks to/from their preferred LLC")
Closes: https://lore.kernel.org/lkml/20260827135000.735138-1-zhanxusheng@xiaomi.com/
Reported-by: Zhan Xusheng <zhanxusheng@xiaomi.com>
Suggested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kayra Cizmeci <kayracizmeci@gmail.com>
Cc: <stable@kernel.org> # v7.2.x
Link: https://patch.msgid.link/06af61afedac32e6477f57feb4d658f6c411c3af.1790035273.git.tim.c.chen@linux.intel.com

1 files changed, 51 insertions, 0 deletions

diff --git a/drivers/usb/common/Kconfig b/drivers/usb/common/Kconfig
new file mode 100644
index 000000000..b85662243
--- /dev/null
+++ b/drivers/usb/common/Kconfig
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: GPL-2.0
+
+config USB_COMMON
+	tristate
+
+
+config USB_LED_TRIG
+	bool "USB LED Triggers"
+	depends on LEDS_CLASS && USB_COMMON && LEDS_TRIGGERS
+	help
+	  This option adds LED triggers for USB host and/or gadget activity.
+
+	  Say Y here if you are working on a system with led-class supported
+	  LEDs and you want to use them as activity indicators for USB host or
+	  gadget.
+
+config USB_ULPI_BUS
+	tristate "USB ULPI PHY interface support"
+	select USB_COMMON
+	help
+	  UTMI+ Low Pin Interface (ULPI) is specification for a commonly used
+	  USB 2.0 PHY interface. The ULPI specification defines a standard set
+	  of registers that can be used to detect the vendor and product which
+	  allows ULPI to be handled as a bus. This module is the driver for that
+	  bus.
+
+	  The ULPI interfaces (the buses) are registered by the drivers for USB
+	  controllers which support ULPI register access and have ULPI PHY
+	  attached to them. The ULPI PHY drivers themselves are normal PHY
+	  drivers.
+
+	  ULPI PHYs provide often functions such as ADP sensing/probing (OTG
+	  protocol) and USB charger detection.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called ulpi.
+
+config USB_CONN_GPIO
+	tristate "USB GPIO Based Connection Detection Driver"
+	depends on GPIOLIB
+	select USB_ROLE_SWITCH
+	select POWER_SUPPLY
+	help
+	  The driver supports USB role switch between host and device via GPIO
+	  based USB cable detection, used typically if an input GPIO is used
+	  to detect USB ID pin, and another input GPIO may be also used to detect
+	  Vbus pin at the same time, it also can be used to enable/disable
+	  device if an input GPIO is only used to detect Vbus pin.
+
+	  To compile the driver as a module, choose M here: the module will
+	  be called usb-conn-gpio.ko