drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validationgrafted

amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and
uses the first encoding that validates. YCbCr 4:4:4 is listed before
RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the
"color format" property is left at AUTO, even though RGB fits the same
link.

That contradicts the documented AUTO behaviour for HDMI in enum
drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when
the bandwidth is not available or the mode is 4:2:0-only), which the
amdgpu implementation of the property also describes. It also leaves
the "Broadcast RGB" property without effect on such sinks, since the
quantization range it selects only applies to RGB output.

Try RGB first. The mask still holds every encoding the sink supports,
so a mode that cannot carry RGB falls back exactly as before.

For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced
through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI
sink that advertised it.

Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation")
Suggested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Assisted-by: Claude Code:claude-fable-5-1
Signed-off-by: Adrian Betschart <adrian.betschart@cinemaone.ch>
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7)

1 files changed, 122 insertions, 0 deletions

diff --git a/drivers/reset/reset-raspberrypi.c b/drivers/reset/reset-raspberrypi.c
new file mode 100644
index 000000000..fa23db554
--- /dev/null
+++ b/drivers/reset/reset-raspberrypi.c
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Raspberry Pi 4 firmware reset driver
+ *
+ * Copyright (C) 2020 Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
+ */
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/reset-controller.h>
+#include <soc/bcm2835/raspberrypi-firmware.h>
+#include <dt-bindings/reset/raspberrypi,firmware-reset.h>
+
+struct rpi_reset {
+	struct reset_controller_dev rcdev;
+	struct rpi_firmware *fw;
+};
+
+static inline struct rpi_reset *to_rpi(struct reset_controller_dev *rcdev)
+{
+	return container_of(rcdev, struct rpi_reset, rcdev);
+}
+
+static int rpi_reset_reset(struct reset_controller_dev *rcdev, unsigned long id)
+{
+	struct rpi_reset *priv = to_rpi(rcdev);
+	u32 dev_addr;
+	int ret;
+
+	switch (id) {
+	case RASPBERRYPI_FIRMWARE_RESET_ID_USB:
+		/*
+		 * The Raspberry Pi 4 gets its USB functionality from VL805, a
+		 * PCIe chip that implements xHCI. After a PCI reset, VL805's
+		 * firmware may either be loaded directly from an EEPROM or, if
+		 * not present, by the SoC's co-processor, VideoCore. rpi's
+		 * VideoCore OS contains both the non public firmware load
+		 * logic and the VL805 firmware blob. This triggers the
+		 * aforementioned process.
+		 *
+		 * The pci device address is expected is expected by the
+		 * firmware encoded like this:
+		 *
+		 *	PCI_BUS << 20 | PCI_SLOT << 15 | PCI_FUNC << 12
+		 *
+		 * But since rpi's PCIe is hardwired, we know the address in
+		 * advance.
+		 */
+		dev_addr = 0x100000;
+		ret = rpi_firmware_property(priv->fw, RPI_FIRMWARE_NOTIFY_XHCI_RESET,
+					    &dev_addr, sizeof(dev_addr));
+		if (ret)
+			return ret;
+
+		/* Wait for vl805 to startup */
+		usleep_range(200, 1000);
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct reset_control_ops rpi_reset_ops = {
+	.reset	= rpi_reset_reset,
+};
+
+static int rpi_reset_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct rpi_firmware *fw;
+	struct device_node *np;
+	struct rpi_reset *priv;
+
+	np = of_get_parent(dev->of_node);
+	if (!np) {
+		dev_err(dev, "Missing firmware node\n");
+		return -ENOENT;
+	}
+
+	fw = devm_rpi_firmware_get(&pdev->dev, np);
+	of_node_put(np);
+	if (!fw)
+		return -EPROBE_DEFER;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	dev_set_drvdata(dev, priv);
+
+	priv->fw = fw;
+	priv->rcdev.owner = THIS_MODULE;
+	priv->rcdev.nr_resets = RASPBERRYPI_FIRMWARE_RESET_NUM_IDS;
+	priv->rcdev.ops = &rpi_reset_ops;
+	priv->rcdev.of_node = dev->of_node;
+
+	return devm_reset_controller_register(dev, &priv->rcdev);
+}
+
+static const struct of_device_id rpi_reset_of_match[] = {
+	{ .compatible = "raspberrypi,firmware-reset" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rpi_reset_of_match);
+
+static struct platform_driver rpi_reset_driver = {
+	.probe	= rpi_reset_probe,
+	.driver	= {
+		.name = "raspberrypi-reset",
+		.of_match_table = rpi_reset_of_match,
+	},
+};
+module_platform_driver(rpi_reset_driver);
+
+MODULE_AUTHOR("Nicolas Saenz Julienne <nsaenzjulienne@suse.de>");
+MODULE_DESCRIPTION("Raspberry Pi 4 firmware reset driver");
+MODULE_LICENSE("GPL");