Merge tag 'driver-core-7.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-coregrafted

Pull driver core fixes from Danilo Krummrich:

 - Fix kernfs listxattr() not returning security xattr names (e.g.
   SELinux labels) when the kernfs node has no allocated kernfs_iattrs

 - Fix silent truncation of IRQ vector indices in the Rust PCI
   abstractions

 - Don't select OF from DRIVER_PE_KUNIT_TEST; skip the test when OF is
   disabled instead of silently enabling extra kernel functionality

 - Russ Weight is retiring from kernel development; update the Firmware
   Loader sysfs contact to the driver-core mailing list, add a CREDITS
   entry for Firmware Upload, and update MAINTAINERS accordingly

* tag 'driver-core-7.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core:
  MAINTAINERS: Remove Russ Weight from Firmware Loader
  CREDITS: Add CREDITS entry for Firmware Upload
  firmware_loader: Change contact for sysfs nodes
  rust: pci: reject IRQ vector indices that do not fit in u32
  kernfs: preserve security xattrs without allocating iattrs
  drivers: base: test: DRIVER_PE_KUNIT_TEST should not select OF

6 files changed, 2252 insertions, 0 deletions

diff --git a/drivers/misc/eeprom/Kconfig b/drivers/misc/eeprom/Kconfig
new file mode 100644
index 000000000..d6af02588
--- /dev/null
+++ b/drivers/misc/eeprom/Kconfig
@@ -0,0 +1,48 @@
+# SPDX-License-Identifier: GPL-2.0-only
+menu "EEPROM support"
+
+config EEPROM_MAX6875
+	tristate "Maxim MAX6874/5 power supply supervisor"
+	depends on I2C
+	help
+	  If you say yes here you get read-only support for the user EEPROM of
+	  the Maxim MAX6874/5 EEPROM-programmable, quad power-supply
+	  sequencer/supervisor.
+
+	  All other features of this chip should be accessed via i2c-dev.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called max6875.
+
+
+config EEPROM_93CX6
+	tristate "EEPROM 93CX6 support"
+	help
+	  This is a driver for the EEPROM chipsets 93c46 and 93c66.
+	  The driver supports both read as well as write commands.
+
+	  If unsure, say N.
+
+config EEPROM_DIGSY_MTC_CFG
+	bool "DigsyMTC display configuration EEPROMs device"
+	depends on GPIO_MPC5200 && SPI_GPIO
+	help
+	  This option enables access to display configuration EEPROMs
+	  on digsy_mtc board. You have to additionally select Microwire
+	  EEPROM 93XX46 driver. sysfs entries will be created for that
+	  EEPROM allowing to read/write the configuration data or to
+	  erase the whole EEPROM.
+
+	  If unsure, say N.
+
+config EEPROM_IDT_89HPESX
+	tristate "IDT 89HPESx PCIe-switches EEPROM / CSR support"
+	depends on I2C && SYSFS
+	help
+	  Enable this driver to get read/write access to EEPROM / CSRs
+	  over IDT PCIe-switch i2c-slave interface.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called idt_89hpesx.
+
+endmenu
diff --git a/drivers/misc/eeprom/Makefile b/drivers/misc/eeprom/Makefile
new file mode 100644
index 000000000..44a20cf02
--- /dev/null
+++ b/drivers/misc/eeprom/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_EEPROM_MAX6875)	+= max6875.o
+obj-$(CONFIG_EEPROM_93CX6)	+= eeprom_93cx6.o
+obj-$(CONFIG_EEPROM_DIGSY_MTC_CFG) += digsy_mtc_eeprom.o
+obj-$(CONFIG_EEPROM_IDT_89HPESX) += idt_89hpesx.o
diff --git a/drivers/misc/eeprom/digsy_mtc_eeprom.c b/drivers/misc/eeprom/digsy_mtc_eeprom.c
new file mode 100644
index 000000000..ee58f7ce5
--- /dev/null
+++ b/drivers/misc/eeprom/digsy_mtc_eeprom.c
@@ -0,0 +1,97 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * EEPROMs access control driver for display configuration EEPROMs
+ * on DigsyMTC board.
+ *
+ * (C) 2011 DENX Software Engineering, Anatolij Gustschin <agust@denx.de>
+ *
+ * FIXME: this driver is used on a device-tree probed platform: it
+ * should be defined as a bit-banged SPI device and probed from the device
+ * tree and not like this with static grabbing of a few numbered GPIO
+ * lines at random.
+ *
+ * Add proper SPI and EEPROM in arch/powerpc/boot/dts/digsy_mtc.dts
+ * and delete this driver.
+ */
+
+#include <linux/gpio/machine.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_gpio.h>
+
+#define GPIO_EEPROM_CLK		216
+#define GPIO_EEPROM_CS		210
+#define GPIO_EEPROM_DI		217
+#define GPIO_EEPROM_DO		249
+#define GPIO_EEPROM_OE		255
+#define EE_SPI_BUS_NUM	1
+
+static const struct property_entry digsy_mtc_spi_properties[] = {
+	PROPERTY_ENTRY_U32("data-size", 8),
+	{ }
+};
+
+static const struct software_node digsy_mtc_spi_node = {
+	.properties = digsy_mtc_spi_properties,
+};
+
+static struct spi_gpio_platform_data eeprom_spi_gpio_data = {
+	.num_chipselect	= 1,
+};
+
+static struct platform_device digsy_mtc_eeprom = {
+	.name	= "spi_gpio",
+	.id	= EE_SPI_BUS_NUM,
+	.dev	= {
+		.platform_data	= &eeprom_spi_gpio_data,
+	},
+};
+
+static struct gpiod_lookup_table eeprom_spi_gpiod_table = {
+	.dev_id         = "spi_gpio.1",
+	.table          = {
+		GPIO_LOOKUP("gpio@b00", GPIO_EEPROM_CLK,
+			    "sck", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio@b00", GPIO_EEPROM_DI,
+			    "mosi", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio@b00", GPIO_EEPROM_DO,
+			    "miso", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio@b00", GPIO_EEPROM_CS,
+			    "cs", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio@b00", GPIO_EEPROM_OE,
+			    "select", GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
+static struct spi_board_info digsy_mtc_eeprom_info[] __initdata = {
+	{
+		.modalias		= "eeprom-93xx46",
+		.max_speed_hz		= 1000000,
+		.bus_num		= EE_SPI_BUS_NUM,
+		.chip_select		= 0,
+		.mode			= SPI_MODE_0,
+	},
+};
+
+static int __init digsy_mtc_eeprom_devices_init(void)
+{
+	int ret;
+
+	gpiod_add_lookup_table(&eeprom_spi_gpiod_table);
+	spi_register_board_info(digsy_mtc_eeprom_info,
+				ARRAY_SIZE(digsy_mtc_eeprom_info));
+
+	ret = device_add_software_node(&digsy_mtc_eeprom.dev, &digsy_mtc_spi_node);
+	if (ret)
+		return ret;
+
+	ret = platform_device_register(&digsy_mtc_eeprom);
+	if (ret)
+		device_remove_software_node(&digsy_mtc_eeprom.dev);
+
+	return ret;
+}
+device_initcall(digsy_mtc_eeprom_devices_init);
diff --git a/drivers/misc/eeprom/eeprom_93cx6.c b/drivers/misc/eeprom/eeprom_93cx6.c
new file mode 100644
index 000000000..e6f0e0fc1
--- /dev/null
+++ b/drivers/misc/eeprom/eeprom_93cx6.c
@@ -0,0 +1,383 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2004 - 2006 rt2x00 SourceForge Project
+ * <http://rt2x00.serialmonkey.com>
+ *
+ * Module: eeprom_93cx6
+ * Abstract: EEPROM reader routines for 93cx6 chipsets.
+ * Supported chipsets: 93c46 & 93c66.
+ */
+
+#include <linux/bits.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/eeprom_93cx6.h>
+
+MODULE_AUTHOR("http://rt2x00.serialmonkey.com");
+MODULE_VERSION("1.0");
+MODULE_DESCRIPTION("EEPROM 93cx6 chip driver");
+MODULE_LICENSE("GPL");
+
+static inline void eeprom_93cx6_pulse_high(struct eeprom_93cx6 *eeprom)
+{
+	eeprom->reg_data_clock = 1;
+	eeprom->register_write(eeprom);
+
+	/*
+	 * Add a short delay for the pulse to work.
+	 * According to the specifications the "maximum minimum"
+	 * time should be 450ns.
+	 */
+	ndelay(450);
+}
+
+static inline void eeprom_93cx6_pulse_low(struct eeprom_93cx6 *eeprom)
+{
+	eeprom->reg_data_clock = 0;
+	eeprom->register_write(eeprom);
+
+	/*
+	 * Add a short delay for the pulse to work.
+	 * According to the specifications the "maximum minimum"
+	 * time should be 450ns.
+	 */
+	ndelay(450);
+}
+
+static void eeprom_93cx6_startup(struct eeprom_93cx6 *eeprom)
+{
+	/*
+	 * Clear all flags, and enable chip select.
+	 */
+	eeprom->register_read(eeprom);
+	eeprom->reg_data_in = 0;
+	eeprom->reg_data_out = 0;
+	eeprom->reg_data_clock = 0;
+	eeprom->reg_chip_select = 1;
+	eeprom->drive_data = 1;
+	eeprom->register_write(eeprom);
+
+	/*
+	 * kick a pulse.
+	 */
+	eeprom_93cx6_pulse_high(eeprom);
+	eeprom_93cx6_pulse_low(eeprom);
+}
+
+static void eeprom_93cx6_cleanup(struct eeprom_93cx6 *eeprom)
+{
+	/*
+	 * Clear chip_select and data_in flags.
+	 */
+	eeprom->register_read(eeprom);
+	eeprom->reg_data_in = 0;
+	eeprom->reg_chip_select = 0;
+	eeprom->register_write(eeprom);
+
+	/*
+	 * kick a pulse.
+	 */
+	eeprom_93cx6_pulse_high(eeprom);
+	eeprom_93cx6_pulse_low(eeprom);
+}
+
+static void eeprom_93cx6_write_bits(struct eeprom_93cx6 *eeprom,
+	const u16 data, const u16 count)
+{
+	unsigned int i;
+
+	eeprom->register_read(eeprom);
+
+	/*
+	 * Clear data flags.
+	 */
+	eeprom->reg_data_in = 0;
+	eeprom->reg_data_out = 0;
+	eeprom->drive_data = 1;
+
+	/*
+	 * Start writing all bits.
+	 */
+	for (i = count; i > 0; i--) {
+		/*
+		 * Check if this bit needs to be set.
+		 */
+		eeprom->reg_data_in = !!(data & BIT(i - 1));
+
+		/*
+		 * Write the bit to the eeprom register.
+		 */
+		eeprom->register_write(eeprom);
+
+		/*
+		 * Kick a pulse.
+		 */
+		eeprom_93cx6_pulse_high(eeprom);
+		eeprom_93cx6_pulse_low(eeprom);
+	}
+
+	eeprom->reg_data_in = 0;
+	eeprom->register_write(eeprom);
+}
+
+static void eeprom_93cx6_read_bits(struct eeprom_93cx6 *eeprom,
+	u16 *data, const u16 count)
+{
+	unsigned int i;
+	u16 buf = 0;
+
+	eeprom->register_read(eeprom);
+
+	/*
+	 * Clear data flags.
+	 */
+	eeprom->reg_data_in = 0;
+	eeprom->reg_data_out = 0;
+	eeprom->drive_data = 0;
+
+	/*
+	 * Start reading all bits.
+	 */
+	for (i = count; i > 0; i--) {
+		eeprom_93cx6_pulse_high(eeprom);
+
+		eeprom->register_read(eeprom);
+
+		/*
+		 * Clear data_in flag.
+		 */
+		eeprom->reg_data_in = 0;
+
+		/*
+		 * Read if the bit has been set.
+		 */
+		if (eeprom->reg_data_out)
+			buf |= BIT(i - 1);
+
+		eeprom_93cx6_pulse_low(eeprom);
+	}
+
+	*data = buf;
+}
+
+/**
+ * eeprom_93cx6_read - Read a word from eeprom
+ * @eeprom: Pointer to eeprom structure
+ * @word: Word index from where we should start reading
+ * @data: target pointer where the information will have to be stored
+ *
+ * This function will read the eeprom data as host-endian word
+ * into the given data pointer.
+ */
+void eeprom_93cx6_read(struct eeprom_93cx6 *eeprom, const u8 word,
+	u16 *data)
+{
+	u16 command;
+
+	/*
+	 * Initialize the eeprom register
+	 */
+	eeprom_93cx6_startup(eeprom);
+
+	/*
+	 * Select the read opcode and the word to be read.
+	 */
+	command = (PCI_EEPROM_READ_OPCODE << eeprom->width) | word;
+	eeprom_93cx6_write_bits(eeprom, command,
+		PCI_EEPROM_WIDTH_OPCODE + eeprom->width);
+
+	if (has_quirk_extra_read_cycle(eeprom)) {
+		eeprom_93cx6_pulse_high(eeprom);
+		eeprom_93cx6_pulse_low(eeprom);
+	}
+
+	/*
+	 * Read the requested 16 bits.
+	 */
+	eeprom_93cx6_read_bits(eeprom, data, 16);
+
+	/*
+	 * Cleanup eeprom register.
+	 */
+	eeprom_93cx6_cleanup(eeprom);
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_read);
+
+/**
+ * eeprom_93cx6_multiread - Read multiple words from eeprom
+ * @eeprom: Pointer to eeprom structure
+ * @word: Word index from where we should start reading
+ * @data: target pointer where the information will have to be stored
+ * @words: Number of words that should be read.
+ *
+ * This function will read all requested words from the eeprom,
+ * this is done by calling eeprom_93cx6_read() multiple times.
+ * But with the additional change that while the eeprom_93cx6_read
+ * will return host ordered bytes, this method will return little
+ * endian words.
+ */
+void eeprom_93cx6_multiread(struct eeprom_93cx6 *eeprom, const u8 word,
+	__le16 *data, const u16 words)
+{
+	unsigned int i;
+	u16 tmp;
+
+	for (i = 0; i < words; i++) {
+		tmp = 0;
+		eeprom_93cx6_read(eeprom, word + i, &tmp);
+		data[i] = cpu_to_le16(tmp);
+	}
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_multiread);
+
+/**
+ * eeprom_93cx6_readb - Read a byte from eeprom
+ * @eeprom: Pointer to eeprom structure
+ * @byte: Byte index from where we should start reading
+ * @data: target pointer where the information will have to be stored
+ *
+ * This function will read a byte of the eeprom data
+ * into the given data pointer.
+ */
+void eeprom_93cx6_readb(struct eeprom_93cx6 *eeprom, const u8 byte,
+	u8 *data)
+{
+	u16 command;
+	u16 tmp;
+
+	/*
+	 * Initialize the eeprom register
+	 */
+	eeprom_93cx6_startup(eeprom);
+
+	/*
+	 * Select the read opcode and the byte to be read.
+	 */
+	command = (PCI_EEPROM_READ_OPCODE << (eeprom->width + 1)) | byte;
+	eeprom_93cx6_write_bits(eeprom, command,
+		PCI_EEPROM_WIDTH_OPCODE + eeprom->width + 1);
+
+	if (has_quirk_extra_read_cycle(eeprom)) {
+		eeprom_93cx6_pulse_high(eeprom);
+		eeprom_93cx6_pulse_low(eeprom);
+	}
+
+	/*
+	 * Read the requested 8 bits.
+	 */
+	eeprom_93cx6_read_bits(eeprom, &tmp, 8);
+	*data = tmp & 0xff;
+
+	/*
+	 * Cleanup eeprom register.
+	 */
+	eeprom_93cx6_cleanup(eeprom);
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_readb);
+
+/**
+ * eeprom_93cx6_multireadb - Read multiple bytes from eeprom
+ * @eeprom: Pointer to eeprom structure
+ * @byte: Index from where we should start reading
+ * @data: target pointer where the information will have to be stored
+ * @bytes: Number of bytes that should be read.
+ *
+ * This function will read all requested bytes from the eeprom,
+ * this is done by calling eeprom_93cx6_readb() multiple times.
+ */
+void eeprom_93cx6_multireadb(struct eeprom_93cx6 *eeprom, const u8 byte,
+	u8 *data, const u16 bytes)
+{
+	unsigned int i;
+
+	for (i = 0; i < bytes; i++)
+		eeprom_93cx6_readb(eeprom, byte + i, &data[i]);
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_multireadb);
+
+/**
+ * eeprom_93cx6_wren - set the write enable state
+ * @eeprom: Pointer to eeprom structure
+ * @enable: true to enable writes, otherwise disable writes
+ *
+ * Set the EEPROM write enable state to either allow or deny
+ * writes depending on the @enable value.
+ */
+void eeprom_93cx6_wren(struct eeprom_93cx6 *eeprom, bool enable)
+{
+	u16 command;
+
+	/* start the command */
+	eeprom_93cx6_startup(eeprom);
+
+	/* create command to enable/disable */
+
+	command = enable ? PCI_EEPROM_EWEN_OPCODE : PCI_EEPROM_EWDS_OPCODE;
+	command <<= (eeprom->width - 2);
+
+	eeprom_93cx6_write_bits(eeprom, command,
+				PCI_EEPROM_WIDTH_OPCODE + eeprom->width);
+
+	eeprom_93cx6_cleanup(eeprom);
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_wren);
+
+/**
+ * eeprom_93cx6_write - write data to the EEPROM
+ * @eeprom: Pointer to eeprom structure
+ * @addr: Address to write data to.
+ * @data: The data to write to address @addr.
+ *
+ * Write the @data to the specified @addr in the EEPROM and
+ * waiting for the device to finish writing.
+ *
+ * Note, since we do not expect large number of write operations
+ * we delay in between parts of the operation to avoid using excessive
+ * amounts of CPU time busy waiting.
+ */
+void eeprom_93cx6_write(struct eeprom_93cx6 *eeprom, u8 addr, u16 data)
+{
+	int timeout = 100;
+	u16 command;
+
+	/* start the command */
+	eeprom_93cx6_startup(eeprom);
+
+	command = PCI_EEPROM_WRITE_OPCODE << eeprom->width;
+	command |= addr;
+
+	/* send write command */
+	eeprom_93cx6_write_bits(eeprom, command,
+				PCI_EEPROM_WIDTH_OPCODE + eeprom->width);
+
+	/* send data */
+	eeprom_93cx6_write_bits(eeprom, data, 16);
+
+	/* get ready to check for busy */
+	eeprom->drive_data = 0;
+	eeprom->reg_chip_select = 1;
+	eeprom->register_write(eeprom);
+
+	/* wait at-least 250ns to get DO to be the busy signal */
+	usleep_range(1000, 2000);
+
+	/* wait for DO to go high to signify finish */
+
+	while (true) {
+		eeprom->register_read(eeprom);
+
+		if (eeprom->reg_data_out)
+			break;
+
+		usleep_range(1000, 2000);
+
+		if (--timeout <= 0) {
+			printk(KERN_ERR "%s: timeout\n", __func__);
+			break;
+		}
+	}
+
+	eeprom_93cx6_cleanup(eeprom);
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_write);
diff --git a/drivers/misc/eeprom/idt_89hpesx.c b/drivers/misc/eeprom/idt_89hpesx.c
new file mode 100644
index 000000000..ea7478cfd
--- /dev/null
+++ b/drivers/misc/eeprom/idt_89hpesx.c
@@ -0,0 +1,1515 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *   Copyright (C) 2016 T-Platforms. All Rights Reserved.
+ *
+ * IDT PCIe-switch NTB Linux driver
+ *
+ * Contact Information:
+ * Serge Semin <fancer.lancer@gmail.com>, <Sergey.Semin@t-platforms.ru>
+ */
+/*
+ *           NOTE of the IDT 89HPESx SMBus-slave interface driver
+ *    This driver primarily is developed to have an access to EEPROM device of
+ * IDT PCIe-switches. IDT provides a simple SMBus interface to perform IO-
+ * operations from/to EEPROM, which is located at private (so called Master)
+ * SMBus of switches. Using that interface this the driver creates a simple
+ * binary sysfs-file in the device directory:
+ * /sys/bus/i2c/devices/<bus>-<devaddr>/eeprom
+ * In case if read-only flag is specified in the dts-node of device desription,
+ * User-space applications won't be able to write to the EEPROM sysfs-node.
+ *    Additionally IDT 89HPESx SMBus interface has an ability to write/read
+ * data of device CSRs. This driver exposes debugf-file to perform simple IO
+ * operations using that ability for just basic debug purpose. Particularly
+ * next file is created in the specific debugfs-directory:
+ * /sys/kernel/debug/idt_csr/
+ * Format of the debugfs-node is:
+ * $ cat /sys/kernel/debug/idt_csr/<bus>-<devaddr>/<devname>;
+ * <CSR address>:<CSR value>
+ * So reading the content of the file gives current CSR address and it value.
+ * If User-space application wishes to change current CSR address,
+ * it can just write a proper value to the sysfs-file:
+ * $ echo "<CSR address>" > /sys/kernel/debug/idt_csr/<bus>-<devaddr>/<devname>
+ * If it wants to change the CSR value as well, the format of the write
+ * operation is:
+ * $ echo "<CSR address>:<CSR value>" > \
+ *        /sys/kernel/debug/idt_csr/<bus>-<devaddr>/<devname>;
+ * CSR address and value can be any of hexadecimal, decimal or octal format.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/sizes.h>
+#include <linux/slab.h>
+#include <linux/mutex.h>
+#include <linux/sysfs.h>
+#include <linux/debugfs.h>
+#include <linux/property.h>
+#include <linux/i2c.h>
+#include <linux/pci_ids.h>
+#include <linux/delay.h>
+
+#define IDT_NAME		"89hpesx"
+#define IDT_89HPESX_DESC	"IDT 89HPESx SMBus-slave interface driver"
+#define IDT_89HPESX_VER		"1.0"
+
+MODULE_DESCRIPTION(IDT_89HPESX_DESC);
+MODULE_VERSION(IDT_89HPESX_VER);
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("T-platforms");
+
+/*
+ * struct idt_89hpesx_dev - IDT 89HPESx device data structure
+ * @eesize:	Size of EEPROM in bytes (calculated from "idt,eecompatible")
+ * @eero:	EEPROM Read-only flag
+ * @eeaddr:	EEPROM custom address
+ *
+ * @inieecmd:	Initial cmd value for EEPROM read/write operations
+ * @inicsrcmd:	Initial cmd value for CSR read/write operations
+ * @iniccode:	Initialial command code value for IO-operations
+ *
+ * @csr:	CSR address to perform read operation
+ *
+ * @smb_write:	SMBus write method
+ * @smb_read:	SMBus read method
+ * @smb_mtx:	SMBus mutex
+ *
+ * @client:	i2c client used to perform IO operations
+ *
+ * @ee_file:	EEPROM read/write sysfs-file
+ */
+struct idt_smb_seq;
+struct idt_89hpesx_dev {
+	u32 eesize;
+	bool eero;
+	u8 eeaddr;
+
+	u8 inieecmd;
+	u8 inicsrcmd;
+	u8 iniccode;
+
+	u16 csr;
+
+	int (*smb_write)(struct idt_89hpesx_dev *, const struct idt_smb_seq *);
+	int (*smb_read)(struct idt_89hpesx_dev *, struct idt_smb_seq *);
+	struct mutex smb_mtx;
+
+	struct i2c_client *client;
+
+	struct bin_attribute *ee_file;
+	struct dentry *csr_dir;
+};
+
+/*
+ * struct idt_smb_seq - sequence of data to be read/written from/to IDT 89HPESx
+ * @ccode:	SMBus command code
+ * @bytecnt:	Byte count of operation
+ * @data:	Data to by written
+ */
+struct idt_smb_seq {
+	u8 ccode;
+	u8 bytecnt;
+	u8 *data;
+};
+
+/*
+ * struct idt_eeprom_seq - sequence of data to be read/written from/to EEPROM
+ * @cmd:	Transaction CMD
+ * @eeaddr:	EEPROM custom address
+ * @memaddr:	Internal memory address of EEPROM
+ * @data:	Data to be written at the memory address
+ */
+struct idt_eeprom_seq {
+	u8 cmd;
+	u8 eeaddr;
+	__le16 memaddr;
+	u8 data;
+} __packed;
+
+/*
+ * struct idt_csr_seq - sequence of data to be read/written from/to CSR
+ * @cmd:	Transaction CMD
+ * @csraddr:	Internal IDT device CSR address
+ * @data:	Data to be read/written from/to the CSR address
+ */
+struct idt_csr_seq {
+	u8 cmd;
+	__le16 csraddr;
+	__le32 data;
+} __packed;
+
+/*
+ * SMBus command code macros
+ * @CCODE_END:		Indicates the end of transaction
+ * @CCODE_START:	Indicates the start of transaction
+ * @CCODE_CSR:		CSR read/write transaction
+ * @CCODE_EEPROM:	EEPROM read/write transaction
+ * @CCODE_BYTE:		Supplied data has BYTE length
+ * @CCODE_WORD:		Supplied data has WORD length
+ * @CCODE_BLOCK:	Supplied data has variable length passed in bytecnt
+ *			byte right following CCODE byte
+ */
+#define CCODE_END	((u8)0x01)
+#define CCODE_START	((u8)0x02)
+#define CCODE_CSR	((u8)0x00)
+#define CCODE_EEPROM	((u8)0x04)
+#define CCODE_BYTE	((u8)0x00)
+#define CCODE_WORD	((u8)0x20)
+#define CCODE_BLOCK	((u8)0x40)
+#define CCODE_PEC	((u8)0x80)
+
+/*
+ * EEPROM command macros
+ * @EEPROM_OP_WRITE:	EEPROM write operation
+ * @EEPROM_OP_READ:	EEPROM read operation
+ * @EEPROM_USA:		Use specified address of EEPROM
+ * @EEPROM_NAERR:	EEPROM device is not ready to respond
+ * @EEPROM_LAERR:	EEPROM arbitration loss error
+ * @EEPROM_MSS:		EEPROM misplace start & stop bits error
+ * @EEPROM_WR_CNT:	Bytes count to perform write operation
+ * @EEPROM_WRRD_CNT:	Bytes count to write before reading
+ * @EEPROM_RD_CNT:	Bytes count to perform read operation
+ * @EEPROM_DEF_SIZE:	Fall back size of EEPROM
+ * @EEPROM_DEF_ADDR:	Defatul EEPROM address
+ * @EEPROM_TOUT:	Timeout before retry read operation if eeprom is busy
+ */
+#define EEPROM_OP_WRITE	((u8)0x00)
+#define EEPROM_OP_READ	((u8)0x01)
+#define EEPROM_USA	((u8)0x02)
+#define EEPROM_NAERR	((u8)0x08)
+#define EEPROM_LAERR    ((u8)0x10)
+#define EEPROM_MSS	((u8)0x20)
+#define EEPROM_WR_CNT	((u8)5)
+#define EEPROM_WRRD_CNT	((u8)4)
+#define EEPROM_RD_CNT	((u8)5)
+#define EEPROM_DEF_SIZE	((u16)4096)
+#define EEPROM_DEF_ADDR	((u8)0x50)
+#define EEPROM_TOUT	(100)
+
+/*
+ * CSR command macros
+ * @CSR_DWE:		Enable all four bytes of the operation
+ * @CSR_OP_WRITE:	CSR write operation
+ * @CSR_OP_READ:	CSR read operation
+ * @CSR_RERR:		Read operation error
+ * @CSR_WERR:		Write operation error
+ * @CSR_WR_CNT:		Bytes count to perform write operation
+ * @CSR_WRRD_CNT:	Bytes count to write before reading
+ * @CSR_RD_CNT:		Bytes count to perform read operation
+ * @CSR_MAX:		Maximum CSR address
+ * @CSR_DEF:		Default CSR address
+ * @CSR_REAL_ADDR:	CSR real unshifted address
+ */
+#define CSR_DWE			((u8)0x0F)
+#define CSR_OP_WRITE		((u8)0x00)
+#define CSR_OP_READ		((u8)0x10)
+#define CSR_RERR		((u8)0x40)
+#define CSR_WERR		((u8)0x80)
+#define CSR_WR_CNT		((u8)7)
+#define CSR_WRRD_CNT		((u8)3)
+#define CSR_RD_CNT		((u8)7)
+#define CSR_MAX			((u32)0x3FFFF)
+#define CSR_DEF			((u16)0x0000)
+#define CSR_REAL_ADDR(val)	((unsigned int)val << 2)
+
+/*
+ * IDT 89HPESx basic register
+ * @IDT_VIDDID_CSR:	PCIe VID and DID of IDT 89HPESx
+ * @IDT_VID_MASK:	Mask of VID
+ */
+#define IDT_VIDDID_CSR	((u32)0x0000)
+#define IDT_VID_MASK	((u32)0xFFFF)
+
+/*
+ * IDT 89HPESx can send NACK when new command is sent before previous one
+ * fininshed execution. In this case driver retries operation
+ * certain times.
+ * @RETRY_CNT:		Number of retries before giving up and fail
+ * @idt_smb_safe:	Generate a retry loop on corresponding SMBus method
+ */
+#define RETRY_CNT (128)
+#define idt_smb_safe(ops, args...) ({ \
+	int __retry = RETRY_CNT; \
+	s32 __sts; \
+	do { \
+		__sts = i2c_smbus_ ## ops ## _data(args); \
+	} while (__retry-- && __sts < 0); \
+	__sts; \
+})
+
+/*===========================================================================
+ *                         i2c bus level IO-operations
+ *===========================================================================
+ */
+
+/*
+ * idt_smb_write_byte() - SMBus write method when I2C_SMBUS_BYTE_DATA operation
+ *                        is only available
+ * @pdev:	Pointer to the driver data
+ * @seq:	Sequence of data to be written
+ */
+static int idt_smb_write_byte(struct idt_89hpesx_dev *pdev,
+			      const struct idt_smb_seq *seq)
+{
+	s32 sts;
+	u8 ccode;
+	int idx;
+
+	/* Loop over the supplied data sending byte one-by-one */
+	for (idx = 0; idx < seq->bytecnt; idx++) {
+		/* Collect the command code byte */
+		ccode = seq->ccode | CCODE_BYTE;
+		if (idx == 0)
+			ccode |= CCODE_START;
+		if (idx == seq->bytecnt - 1)
+			ccode |= CCODE_END;
+
+		/* Send data to the device */
+		sts = idt_smb_safe(write_byte, pdev->client, ccode,
+			seq->data[idx]);
+		if (sts != 0)
+			return (int)sts;
+	}
+
+	return 0;
+}
+
+/*
+ * idt_smb_read_byte() - SMBus read method when I2C_SMBUS_BYTE_DATA operation
+ *                        is only available
+ * @pdev:	Pointer to the driver data
+ * @seq:	Buffer to read data to
+ */
+static int idt_smb_read_byte(struct idt_89hpesx_dev *pdev,
+			     struct idt_smb_seq *seq)
+{
+	s32 sts;
+	u8 ccode;
+	int idx;
+
+	/* Loop over the supplied buffer receiving byte one-by-one */
+	for (idx = 0; idx < seq->bytecnt; idx++) {
+		/* Collect the command code byte */
+		ccode = seq->ccode | CCODE_BYTE;
+		if (idx == 0)
+			ccode |= CCODE_START;
+		if (idx == seq->bytecnt - 1)
+			ccode |= CCODE_END;
+
+		/* Read data from the device */
+		sts = idt_smb_safe(read_byte, pdev->client, ccode);
+		if (sts < 0)
+			return (int)sts;
+
+		seq->data[idx] = (u8)sts;
+	}
+
+	return 0;
+}
+
+/*
+ * idt_smb_write_word() - SMBus write method when I2C_SMBUS_BYTE_DATA and
+ *                        I2C_FUNC_SMBUS_WORD_DATA operations are available
+ * @pdev:	Pointer to the driver data
+ * @seq:	Sequence of data to be written
+ */
+static int idt_smb_write_word(struct idt_89hpesx_dev *pdev,
+			      const struct idt_smb_seq *seq)
+{
+	s32 sts;
+	u8 ccode;
+	int idx, evencnt;
+
+	/* Calculate the even count of data to send */
+	evencnt = seq->bytecnt - (seq->bytecnt % 2);
+
+	/* Loop over the supplied data sending two bytes at a time */
+	for (idx = 0; idx < evencnt; idx += 2) {
+		/* Collect the command code byte */
+		ccode = seq->ccode | CCODE_WORD;
+		if (idx == 0)
+			ccode |= CCODE_START;
+		if (idx == evencnt - 2)
+			ccode |= CCODE_END;
+
+		/* Send word data to the device */
+		sts = idt_smb_safe(write_word, pdev->client, ccode,
+			*(u16 *)&seq->data[idx]);
+		if (sts != 0)
+			return (int)sts;
+	}
+
+	/* If there is odd number of bytes then send just one last byte */
+	if (seq->bytecnt != evencnt) {
+		/* Collect the command code byte */
+		ccode = seq->ccode | CCODE_BYTE | CCODE_END;
+		if (idx == 0)
+			ccode |= CCODE_START;
+
+		/* Send byte data to the device */
+		sts = idt_smb_safe(write_byte, pdev->client, ccode,
+			seq->data[idx]);
+		if (sts != 0)
+			return (int)sts;
+	}
+
+	return 0;
+}
+
+/*
+ * idt_smb_read_word() - SMBus read method when I2C_SMBUS_BYTE_DATA and
+ *                       I2C_FUNC_SMBUS_WORD_DATA operations are available
+ * @pdev:	Pointer to the driver data
+ * @seq:	Buffer to read data to
+ */
+static int idt_smb_read_word(struct idt_89hpesx_dev *pdev,
+			     struct idt_smb_seq *seq)
+{
+	s32 sts;
+	u8 ccode;
+	int idx, evencnt;
+
+	/* Calculate the even count of data to send */
+	evencnt = seq->bytecnt - (seq->bytecnt % 2);
+
+	/* Loop over the supplied data reading two bytes at a time */
+	for (idx = 0; idx < evencnt; idx += 2) {
+		/* Collect the command code byte */
+		ccode = seq->ccode | CCODE_WORD;
+		if (idx == 0)
+			ccode |= CCODE_START;
+		if (idx == evencnt - 2)
+			ccode |= CCODE_END;
+
+		/* Read word data from the device */
+		sts = idt_smb_safe(read_word, pdev->client, ccode);
+		if (sts < 0)
+			return (int)sts;
+
+		*(u16 *)&seq->data[idx] = (u16)sts;
+	}
+
+	/* If there is odd number of bytes then receive just one last byte */
+	if (seq->bytecnt != evencnt) {
+		/* Collect the command code byte */
+		ccode = seq->ccode | CCODE_BYTE | CCODE_END;
+		if (idx == 0)
+			ccode |= CCODE_START;
+
+		/* Read last data byte from the device */
+		sts = idt_smb_safe(read_byte, pdev->client, ccode);
+		if (sts < 0)
+			return (int)sts;
+
+		seq->data[idx] = (u8)sts;
+	}
+
+	return 0;
+}
+
+/*
+ * idt_smb_write_block() - SMBus write method when I2C_SMBUS_BLOCK_DATA
+ *                         operation is available
+ * @pdev:	Pointer to the driver data
+ * @seq:	Sequence of data to be written
+ */
+static int idt_smb_write_block(struct idt_89hpesx_dev *pdev,
+			       const struct idt_smb_seq *seq)
+{
+	u8 ccode;
+
+	/* Return error if too much data passed to send */
+	if (seq->bytecnt > I2C_SMBUS_BLOCK_MAX)
+		return -EINVAL;
+
+	/* Collect the command code byte */
+	ccode = seq->ccode | CCODE_BLOCK | CCODE_START | CCODE_END;
+
+	/* Send block of data to the device */
+	return idt_smb_safe(write_block, pdev->client, ccode, seq->bytecnt,
+		seq->data);
+}
+
+/*
+ * idt_smb_read_block() - SMBus read method when I2C_SMBUS_BLOCK_DATA
+ *                        operation is available
+ * @pdev:	Pointer to the driver data
+ * @seq:	Buffer to read data to
+ */
+static int idt_smb_read_block(struct idt_89hpesx_dev *pdev,
+			      struct idt_smb_seq *seq)
+{
+	s32 sts;
+	u8 ccode;
+
+	/* Return error if too much data passed to send */
+	if (seq->bytecnt > I2C_SMBUS_BLOCK_MAX)
+		return -EINVAL;
+
+	/* Collect the command code byte */
+	ccode = seq->ccode | CCODE_BLOCK | CCODE_START | CCODE_END;
+
+	/* Read block of data from the device */
+	sts = idt_smb_safe(read_block, pdev->client, ccode, seq->data);
+	if (sts != seq->bytecnt)
+		return (sts < 0 ? sts : -ENODATA);
+
+	return 0;
+}
+
+/*
+ * idt_smb_write_i2c_block() - SMBus write method when I2C_SMBUS_I2C_BLOCK_DATA
+ *                             operation is available
+ * @pdev:	Pointer to the driver data
+ * @seq:	Sequence of data to be written
+ *
+ * NOTE It's usual SMBus write block operation, except the actual data length is
+ * sent as first byte of data
+ */
+static int idt_smb_write_i2c_block(struct idt_89hpesx_dev *pdev,
+				   const struct idt_smb_seq *seq)
+{
+	u8 ccode, buf[I2C_SMBUS_BLOCK_MAX + 1];
+
+	/* Return error if too much data passed to send */
+	if (seq->bytecnt > I2C_SMBUS_BLOCK_MAX)
+		return -EINVAL;
+
+	/* Collect the data to send. Length byte must be added prior the data */
+	buf[0] = seq->bytecnt;
+	memcpy(&buf[1], seq->data, seq->bytecnt);
+
+	/* Collect the command code byte */
+	ccode = seq->ccode | CCODE_BLOCK | CCODE_START | CCODE_END;
+
+	/* Send length and block of data to the device */
+	return idt_smb_safe(write_i2c_block, pdev->client, ccode,
+		seq->bytecnt + 1, buf);
+}
+
+/*
+ * idt_smb_read_i2c_block() - SMBus read method when I2C_SMBUS_I2C_BLOCK_DATA
+ *                            operation is available
+ * @pdev:	Pointer to the driver data
+ * @seq:	Buffer to read data to
+ *
+ * NOTE It's usual SMBus read block operation, except the actual data length is
+ * retrieved as first byte of data
+ */
+static int idt_smb_read_i2c_block(struct idt_89hpesx_dev *pdev,
+				  struct idt_smb_seq *seq)
+{
+	u8 ccode, buf[I2C_SMBUS_BLOCK_MAX + 1];
+	s32 sts;
+
+	/* Return error if too much data passed to send */
+	if (seq->bytecnt > I2C_SMBUS_BLOCK_MAX)
+		return -EINVAL;
+
+	/* Collect the command code byte */
+	ccode = seq->ccode | CCODE_BLOCK | CCODE_START | CCODE_END;
+
+	/* Read length and block of data from the device */
+	sts = idt_smb_safe(read_i2c_block, pdev->client, ccode,
+		seq->bytecnt + 1, buf);
+	if (sts != seq->bytecnt + 1)
+		return (sts < 0 ? sts : -ENODATA);
+	if (buf[0] != seq->bytecnt)
+		return -ENODATA;
+
+	/* Copy retrieved data to the output data buffer */
+	memcpy(seq->data, &buf[1], seq->bytecnt);
+
+	return 0;
+}
+
+/*===========================================================================
+ *                          EEPROM IO-operations
+ *===========================================================================
+ */
+
+/*
+ * idt_eeprom_read_byte() - read just one byte from EEPROM
+ * @pdev:	Pointer to the driver data
+ * @memaddr:	Start EEPROM memory address
+ * @data:	Data to be written to EEPROM
+ */
+static int idt_eeprom_read_byte(struct idt_89hpesx_dev *pdev, u16 memaddr,
+				u8 *data)
+{
+	struct device *dev = &pdev->client->dev;
+	struct idt_eeprom_seq eeseq;
+	struct idt_smb_seq smbseq;
+	int ret, retry;
+
+	/* Initialize SMBus sequence fields */
+	smbseq.ccode = pdev->iniccode | CCODE_EEPROM;
+	smbseq.data = (u8 *)&eeseq;
+
+	/*
+	 * Sometimes EEPROM may respond with NACK if it's busy with previous
+	 * operation, so we need to perform a few attempts of read cycle
+	 */
+	retry = RETRY_CNT;
+	do {
+		/* Send EEPROM memory address to read data from */
+		smbseq.bytecnt = EEPROM_WRRD_CNT;
+		eeseq.cmd = pdev->inieecmd | EEPROM_OP_READ;
+		eeseq.eeaddr = pdev->eeaddr;
+		eeseq.memaddr = cpu_to_le16(memaddr);
+		ret = pdev->smb_write(pdev, &smbseq);
+		if (ret != 0) {
+			dev_err(dev, "Failed to init eeprom addr 0x%02x",
+				memaddr);
+			break;
+		}
+
+		/* Perform read operation */
+		smbseq.bytecnt = EEPROM_RD_CNT;
+		ret = pdev->smb_read(pdev, &smbseq);
+		if (ret != 0) {
+			dev_err(dev, "Failed to read eeprom data 0x%02x",
+				memaddr);
+			break;
+		}
+
+		/* Restart read operation if the device is busy */
+		if (retry && (eeseq.cmd & EEPROM_NAERR)) {
+			dev_dbg(dev, "EEPROM busy, retry reading after %d ms",
+				EEPROM_TOUT);
+			msleep(EEPROM_TOUT);
+			continue;
+		}
+
+		/* Check whether IDT successfully read data from EEPROM */
+		if (eeseq.cmd & (EEPROM_NAERR | EEPROM_LAERR | EEPROM_MSS)) {
+			dev_err(dev,
+				"Communication with eeprom failed, cmd 0x%hhx",
+				eeseq.cmd);
+			ret = -EREMOTEIO;
+			break;
+		}
+
+		/* Save retrieved data and exit the loop */
+		*data = eeseq.data;
+		break;
+	} while (retry--);
+
+	/* Return the status of operation */
+	return ret;
+}
+
+/*
+ * idt_eeprom_write() - EEPROM write operation
+ * @pdev:	Pointer to the driver data
+ * @memaddr:	Start EEPROM memory address
+ * @len:	Length of data to be written
+ * @data:	Data to be written to EEPROM
+ */
+static int idt_eeprom_write(struct idt_89hpesx_dev *pdev, u16 memaddr, u16 len,
+			    const u8 *data)
+{
+	struct device *dev = &pdev->client->dev;
+	struct idt_eeprom_seq eeseq;
+	struct idt_smb_seq smbseq;
+	int ret;
+	u16 idx;
+
+	/* Initialize SMBus sequence fields */
+	smbseq.ccode = pdev->iniccode | CCODE_EEPROM;
+	smbseq.data = (u8 *)&eeseq;
+
+	/* Send data byte-by-byte, checking if it is successfully written */
+	for (idx = 0; idx < len; idx++, memaddr++) {
+		/* Lock IDT SMBus device */
+		mutex_lock(&pdev->smb_mtx);
+
+		/* Perform write operation */
+		smbseq.bytecnt = EEPROM_WR_CNT;
+		eeseq.cmd = pdev->inieecmd | EEPROM_OP_WRITE;
+		eeseq.eeaddr = pdev->eeaddr;
+		eeseq.memaddr = cpu_to_le16(memaddr);
+		eeseq.data = data[idx];
+		ret = pdev->smb_write(pdev, &smbseq);
+		if (ret != 0) {
+			dev_err(dev,
+				"Failed to write 0x%04hx:0x%02hhx to eeprom",
+				memaddr, data[idx]);
+			goto err_mutex_unlock;
+		}
+
+		/*
+		 * Check whether the data is successfully written by reading
+		 * from the same EEPROM memory address.
+		 */
+		eeseq.data = ~data[idx];
+		ret = idt_eeprom_read_byte(pdev, memaddr, &eeseq.data);
+		if (ret != 0)
+			goto err_mutex_unlock;
+
+		/* Check whether the read byte is the same as written one */
+		if (eeseq.data != data[idx]) {
+			dev_err(dev, "Values don't match 0x%02hhx != 0x%02hhx",
+				eeseq.data, data[idx]);
+			ret = -EREMOTEIO;
+			goto err_mutex_unlock;
+		}
+
+		/* Unlock IDT SMBus device */
+err_mutex_unlock:
+		mutex_unlock(&pdev->smb_mtx);
+		if (ret != 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * idt_eeprom_read() - EEPROM read operation
+ * @pdev:	Pointer to the driver data
+ * @memaddr:	Start EEPROM memory address
+ * @len:	Length of data to read
+ * @buf:	Buffer to read data to
+ */
+static int idt_eeprom_read(struct idt_89hpesx_dev *pdev, u16 memaddr, u16 len,
+			   u8 *buf)
+{
+	int ret;
+	u16 idx;
+
+	/* Read data byte-by-byte, retrying if it wasn't successful */
+	for (idx = 0; idx < len; idx++, memaddr++) {
+		/* Lock IDT SMBus device */
+		mutex_lock(&pdev->smb_mtx);
+
+		/* Just read the byte to the buffer */
+		ret = idt_eeprom_read_byte(pdev, memaddr, &buf[idx]);
+
+		/* Unlock IDT SMBus device */
+		mutex_unlock(&pdev->smb_mtx);
+
+		/* Return error if read operation failed */
+		if (ret != 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+/*===========================================================================
+ *                          CSR IO-operations
+ *===========================================================================
+ */
+
+/*
+ * idt_csr_write() - CSR write operation
+ * @pdev:	Pointer to the driver data
+ * @csraddr:	CSR address (with no two LS bits)
+ * @data:	Data to be written to CSR
+ */
+static int idt_csr_write(struct idt_89hpesx_dev *pdev, u16 csraddr,
+			 const u32 data)
+{
+	struct device *dev = &pdev->client->dev;
+	struct idt_csr_seq csrseq;
+	struct idt_smb_seq smbseq;
+	int ret;
+
+	/* Initialize SMBus sequence fields */
+	smbseq.ccode = pdev->iniccode | CCODE_CSR;
+	smbseq.data = (u8 *)&csrseq;
+
+	/* Lock IDT SMBus device */
+	mutex_lock(&pdev->smb_mtx);
+
+	/* Perform write operation */
+	smbseq.bytecnt = CSR_WR_CNT;
+	csrseq.cmd = pdev->inicsrcmd | CSR_OP_WRITE;
+	csrseq.csraddr = cpu_to_le16(csraddr);
+	csrseq.data = cpu_to_le32(data);
+	ret = pdev->smb_write(pdev, &smbseq);
+	if (ret != 0) {
+		dev_err(dev, "Failed to write 0x%04x: 0x%04x to csr",
+			CSR_REAL_ADDR(csraddr), data);
+		goto err_mutex_unlock;
+	}
+
+	/* Send CSR address to read data from */
+	smbseq.bytecnt = CSR_WRRD_CNT;
+	csrseq.cmd = pdev->inicsrcmd | CSR_OP_READ;
+	ret = pdev->smb_write(pdev, &smbseq);
+	if (ret != 0) {
+		dev_err(dev, "Failed to init csr address 0x%04x",
+			CSR_REAL_ADDR(csraddr));
+		goto err_mutex_unlock;
+	}
+
+	/* Perform read operation */
+	smbseq.bytecnt = CSR_RD_CNT;
+	ret = pdev->smb_read(pdev, &smbseq);
+	if (ret != 0) {
+		dev_err(dev, "Failed to read csr 0x%04x",
+			CSR_REAL_ADDR(csraddr));
+		goto err_mutex_unlock;
+	}
+
+	/* Check whether IDT successfully retrieved CSR data */
+	if (csrseq.cmd & (CSR_RERR | CSR_WERR)) {
+		dev_err(dev, "IDT failed to perform CSR r/w");
+		ret = -EREMOTEIO;
+		goto err_mutex_unlock;
+	}
+
+	/* Unlock IDT SMBus device */
+err_mutex_unlock:
+	mutex_unlock(&pdev->smb_mtx);
+
+	return ret;
+}
+
+/*
+ * idt_csr_read() - CSR read operation
+ * @pdev:	Pointer to the driver data
+ * @csraddr:	CSR address (with no two LS bits)
+ * @data:	Data to be written to CSR
+ */
+static int idt_csr_read(struct idt_89hpesx_dev *pdev, u16 csraddr, u32 *data)
+{
+	struct device *dev = &pdev->client->dev;
+	struct idt_csr_seq csrseq;
+	struct idt_smb_seq smbseq;
+	int ret;
+
+	/* Initialize SMBus sequence fields */
+	smbseq.ccode = pdev->iniccode | CCODE_CSR;
+	smbseq.data = (u8 *)&csrseq;
+
+	/* Lock IDT SMBus device */
+	mutex_lock(&pdev->smb_mtx);
+
+	/* Send CSR register address before reading it */
+	smbseq.bytecnt = CSR_WRRD_CNT;
+	csrseq.cmd = pdev->inicsrcmd | CSR_OP_READ;
+	csrseq.csraddr = cpu_to_le16(csraddr);
+	ret = pdev->smb_write(pdev, &smbseq);
+	if (ret != 0) {
+		dev_err(dev, "Failed to init csr address 0x%04x",
+			CSR_REAL_ADDR(csraddr));
+		goto err_mutex_unlock;
+	}
+
+	/* Perform read operation */
+	smbseq.bytecnt = CSR_RD_CNT;
+	ret = pdev->smb_read(pdev, &smbseq);
+	if (ret != 0) {
+		dev_err(dev, "Failed to read csr 0x%04x",
+			CSR_REAL_ADDR(csraddr));
+		goto err_mutex_unlock;
+	}
+
+	/* Check whether IDT successfully retrieved CSR data */
+	if (csrseq.cmd & (CSR_RERR | CSR_WERR)) {
+		dev_err(dev, "IDT failed to perform CSR r/w");
+		ret = -EREMOTEIO;
+		goto err_mutex_unlock;
+	}
+
+	/* Save data retrieved from IDT */
+	*data = le32_to_cpu(csrseq.data);
+
+	/* Unlock IDT SMBus device */
+err_mutex_unlock:
+	mutex_unlock(&pdev->smb_mtx);
+
+	return ret;
+}
+
+/*===========================================================================
+ *                          Sysfs/debugfs-nodes IO-operations
+ *===========================================================================
+ */
+
+/*
+ * eeprom_write() - EEPROM sysfs-node write callback
+ * @filep:	Pointer to the file system node
+ * @kobj:	Pointer to the kernel object related to the sysfs-node
+ * @attr:	Attributes of the file
+ * @buf:	Buffer to write data to
+ * @off:	Offset at which data should be written to
+ * @count:	Number of bytes to write
+ */
+static ssize_t eeprom_write(struct file *filp, struct kobject *kobj,
+			    const struct bin_attribute *attr,
+			    char *buf, loff_t off, size_t count)
+{
+	struct idt_89hpesx_dev *pdev;
+	int ret;
+
+	/* Retrieve driver data */
+	pdev = dev_get_drvdata(kobj_to_dev(kobj));
+
+	/* Perform EEPROM write operation */
+	ret = idt_eeprom_write(pdev, (u16)off, (u16)count, (u8 *)buf);
+	return (ret != 0 ? ret : count);
+}
+
+/*
+ * eeprom_read() - EEPROM sysfs-node read callback
+ * @filep:	Pointer to the file system node
+ * @kobj:	Pointer to the kernel object related to the sysfs-node
+ * @attr:	Attributes of the file
+ * @buf:	Buffer to write data to
+ * @off:	Offset at which data should be written to
+ * @count:	Number of bytes to write
+ */
+static ssize_t eeprom_read(struct file *filp, struct kobject *kobj,
+			   const struct bin_attribute *attr,
+			   char *buf, loff_t off, size_t count)
+{
+	struct idt_89hpesx_dev *pdev;
+	int ret;
+
+	/* Retrieve driver data */
+	pdev = dev_get_drvdata(kobj_to_dev(kobj));
+
+	/* Perform EEPROM read operation */
+	ret = idt_eeprom_read(pdev, (u16)off, (u16)count, (u8 *)buf);
+	return (ret != 0 ? ret : count);
+}
+
+/*
+ * idt_dbgfs_csr_write() - CSR debugfs-node write callback
+ * @filep:	Pointer to the file system file descriptor
+ * @buf:	Buffer to read data from
+ * @count:	Size of the buffer
+ * @offp:	Offset within the file
+ *
+ * It accepts either "0x<reg addr>:0x<value>" for saving register address
+ * and writing value to specified DWORD register or "0x<reg addr>" for
+ * just saving register address in order to perform next read operation.
+ *
+ * WARNING No spaces are allowed. Incoming string must be strictly formated as:
+ * "<reg addr>:<value>". Register address must be aligned within 4 bytes
+ * (one DWORD).
+ */
+static ssize_t idt_dbgfs_csr_write(struct file *filep, const char __user *ubuf,
+				   size_t count, loff_t *offp)
+{
+	struct idt_89hpesx_dev *pdev = filep->private_data;
+	char *colon_ch, *csraddr_str, *csrval_str;
+	int ret;
+	u32 csraddr, csrval;
+	char *buf;
+
+	if (*offp)
+		return 0;
+
+	/* Copy data from User-space */
+	buf = memdup_user_nul(ubuf, count);
+	if (IS_ERR(buf))
+		return PTR_ERR(buf);
+
+	/* Find position of colon in the buffer */
+	colon_ch = strnchr(buf, count, ':');
+
+	/*
+	 * If there is colon passed then new CSR value should be parsed as
+	 * well, so allocate buffer for CSR address substring.
+	 * If no colon is found, then string must have just one number with
+	 * no new CSR value
+	 */
+	if (colon_ch != NULL) {
+		/* Copy the register address to the substring buffer */
+		csraddr_str = kmemdup_nul(buf, colon_ch - buf, GFP_KERNEL);
+		if (csraddr_str == NULL) {
+			ret = -ENOMEM;
+			goto free_buf;
+		}
+		/* Register value must follow the colon */
+		csrval_str = colon_ch + 1;
+	} else /* if (str_colon == NULL) */ {
+		csraddr_str = (char *)buf; /* Just to shut warning up */
+		csrval_str = NULL;
+	}
+
+	/* Convert CSR address to u32 value */
+	ret = kstrtou32(csraddr_str, 0, &csraddr);
+	if (ret != 0)
+		goto free_csraddr_str;
+
+	/* Check whether passed register address is valid */
+	if (csraddr > CSR_MAX || !IS_ALIGNED(csraddr, SZ_4)) {
+		ret = -EINVAL;
+		goto free_csraddr_str;
+	}
+
+	/* Shift register address to the right so to have u16 address */
+	pdev->csr = (csraddr >> 2);
+
+	/* Parse new CSR value and send it to IDT, if colon has been found */
+	if (colon_ch != NULL) {
+		ret = kstrtou32(csrval_str, 0, &csrval);
+		if (ret != 0)
+			goto free_csraddr_str;
+
+		ret = idt_csr_write(pdev, pdev->csr, csrval);
+		if (ret != 0)
+			goto free_csraddr_str;
+	}
+
+	/* Free memory only if colon has been found */
+free_csraddr_str:
+	if (colon_ch != NULL)
+		kfree(csraddr_str);
+
+	/* Free buffer allocated for data retrieved from User-space */
+free_buf:
+	kfree(buf);
+
+	return (ret != 0 ? ret : count);
+}
+
+/*
+ * idt_dbgfs_csr_read() - CSR debugfs-node read callback
+ * @filep:	Pointer to the file system file descriptor
+ * @buf:	Buffer to write data to
+ * @count:	Size of the buffer
+ * @offp:	Offset within the file
+ *
+ * It just prints the pair "0x<reg addr>:0x<value>" to passed buffer.
+ */
+#define CSRBUF_SIZE	((size_t)32)
+static ssize_t idt_dbgfs_csr_read(struct file *filep, char __user *ubuf,
+				  size_t count, loff_t *offp)
+{
+	struct idt_89hpesx_dev *pdev = filep->private_data;
+	u32 csraddr, csrval;
+	char buf[CSRBUF_SIZE];
+	int ret, size;
+
+	/* Perform CSR read operation */
+	ret = idt_csr_read(pdev, pdev->csr, &csrval);
+	if (ret != 0)
+		return ret;
+
+	/* Shift register address to the left so to have real address */
+	csraddr = ((u32)pdev->csr << 2);
+
+	/* Print the "0x<reg addr>:0x<value>" to buffer */
+	size = snprintf(buf, CSRBUF_SIZE, "0x%05x:0x%08x\n",
+		(unsigned int)csraddr, (unsigned int)csrval);
+
+	/* Copy data to User-space */
+	return simple_read_from_buffer(ubuf, count, offp, buf, size);
+}
+
+/*
+ * eeprom_attribute - EEPROM sysfs-node attributes
+ *
+ * NOTE Size will be changed in compliance with OF node. EEPROM attribute will
+ * be read-only as well if the corresponding flag is specified in OF node.
+ */
+static const BIN_ATTR_RW(eeprom, EEPROM_DEF_SIZE);
+
+/*
+ * csr_dbgfs_ops - CSR debugfs-node read/write operations
+ */
+static const struct file_operations csr_dbgfs_ops = {
+	.owner = THIS_MODULE,
+	.open = simple_open,
+	.write = idt_dbgfs_csr_write,
+	.read = idt_dbgfs_csr_read
+};
+
+/*===========================================================================
+ *                       Driver init/deinit methods
+ *===========================================================================
+ */
+
+/*
+ * idt_set_defval() - disable EEPROM access by default
+ * @pdev:	Pointer to the driver data
+ */
+static void idt_set_defval(struct idt_89hpesx_dev *pdev)
+{
+	/* If OF info is missing then use next values */
+	pdev->eesize = 0;
+	pdev->eero = true;
+	pdev->inieecmd = 0;
+	pdev->eeaddr = 0;
+}
+
+static const struct i2c_device_id ee_ids[];
+
+/*
+ * idt_ee_match_id() - check whether the node belongs to compatible EEPROMs
+ */
+static const struct i2c_device_id *idt_ee_match_id(struct fwnode_handle *fwnode)
+{
+	const struct i2c_device_id *id = ee_ids;
+	const char *compatible, *p;
+	char devname[I2C_NAME_SIZE];
+	int ret;
+
+	ret = fwnode_property_read_string(fwnode, "compatible", &compatible);
+	if (ret)
+		return NULL;
+
+	p = strchr(compatible, ',');
+	strscpy(devname, p ? p + 1 : compatible, sizeof(devname));
+	/* Search through the device name */
+	while (id->name[0]) {
+		if (strcmp(devname, id->name) == 0)
+			return id;
+		id++;
+	}
+	return NULL;
+}
+
+/*
+ * idt_get_fw_data() - get IDT i2c-device parameters from device tree
+ * @pdev:	Pointer to the driver data
+ */
+static void idt_get_fw_data(struct idt_89hpesx_dev *pdev)
+{
+	struct device *dev = &pdev->client->dev;
+	struct fwnode_handle *fwnode;
+	const struct i2c_device_id *ee_id = NULL;
+	u32 eeprom_addr;
+	int ret;
+
+	device_for_each_child_node(dev, fwnode) {
+		ee_id = idt_ee_match_id(fwnode);
+		if (ee_id)
+			break;
+
+		dev_warn(dev, "Skip unsupported EEPROM device %pfw\n", fwnode);
+	}
+
+	/* If there is no fwnode EEPROM device, then set zero size */
+	if (!ee_id) {
+		dev_warn(dev, "No fwnode, EEPROM access disabled");
+		idt_set_defval(pdev);
+		return;
+	}
+
+	/* Retrieve EEPROM size */
+	pdev->eesize = (u32)ee_id->driver_data;
+
+	/* Get custom EEPROM address from 'reg' attribute */
+	ret = fwnode_property_read_u32(fwnode, "reg", &eeprom_addr);
+	if (ret || (eeprom_addr == 0)) {
+		dev_warn(dev, "No EEPROM reg found, use default address 0x%x",
+			 EEPROM_DEF_ADDR);
+		pdev->inieecmd = 0;
+		pdev->eeaddr = EEPROM_DEF_ADDR << 1;
+	} else {
+		pdev->inieecmd = EEPROM_USA;
+		pdev->eeaddr = eeprom_addr << 1;
+	}
+
+	/* Check EEPROM 'read-only' flag */
+	if (fwnode_property_read_bool(fwnode, "read-only"))
+		pdev->eero = true;
+	else /* if (!fwnode_property_read_bool(node, "read-only")) */
+		pdev->eero = false;
+
+	fwnode_handle_put(fwnode);
+	dev_info(dev, "EEPROM of %d bytes found by 0x%x",
+		pdev->eesize, pdev->eeaddr);
+}
+
+/*
+ * idt_create_pdev() - create and init data structure of the driver
+ * @client:	i2c client of IDT PCIe-switch device
+ */
+static struct idt_89hpesx_dev *idt_create_pdev(struct i2c_client *client)
+{
+	struct idt_89hpesx_dev *pdev;
+
+	/* Allocate memory for driver data */
+	pdev = devm_kmalloc(&client->dev, sizeof(struct idt_89hpesx_dev),
+		GFP_KERNEL);
+	if (pdev == NULL)
+		return ERR_PTR(-ENOMEM);
+
+	/* Initialize basic fields of the data */
+	pdev->client = client;
+	i2c_set_clientdata(client, pdev);
+
+	/* Read firmware nodes information */
+	idt_get_fw_data(pdev);
+
+	/* Initialize basic CSR CMD field - use full DWORD-sized r/w ops */
+	pdev->inicsrcmd = CSR_DWE;
+	pdev->csr = CSR_DEF;
+
+	/* Enable Packet Error Checking if it's supported by adapter */
+	if (i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_PEC)) {
+		pdev->iniccode = CCODE_PEC;
+		client->flags |= I2C_CLIENT_PEC;
+	} else /* PEC is unsupported */ {
+		pdev->iniccode = 0;
+	}
+
+	return pdev;
+}
+
+/*
+ * idt_free_pdev() - free data structure of the driver
+ * @pdev:	Pointer to the driver data
+ */
+static void idt_free_pdev(struct idt_89hpesx_dev *pdev)
+{
+	/* Clear driver data from device private field */
+	i2c_set_clientdata(pdev->client, NULL);
+}
+
+/*
+ * idt_set_smbus_ops() - set supported SMBus operations
+ * @pdev:	Pointer to the driver data
+ * Return status of smbus check operations
+ */
+static int idt_set_smbus_ops(struct idt_89hpesx_dev *pdev)
+{
+	struct i2c_adapter *adapter = pdev->client->adapter;
+	struct device *dev = &pdev->client->dev;
+
+	/* Check i2c adapter read functionality */
+	if (i2c_check_functionality(adapter,
+				    I2C_FUNC_SMBUS_READ_BLOCK_DATA)) {
+		pdev->smb_read = idt_smb_read_block;
+		dev_dbg(dev, "SMBus block-read op chosen");
+	} else if (i2c_check_functionality(adapter,
+					   I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
+		pdev->smb_read = idt_smb_read_i2c_block;
+		dev_dbg(dev, "SMBus i2c-block-read op chosen");
+	} else if (i2c_check_functionality(adapter,
+					   I2C_FUNC_SMBUS_READ_WORD_DATA) &&
+		   i2c_check_functionality(adapter,
+					   I2C_FUNC_SMBUS_READ_BYTE_DATA)) {
+		pdev->smb_read = idt_smb_read_word;
+		dev_warn(dev, "Use slow word/byte SMBus read ops");
+	} else if (i2c_check_functionality(adapter,
+					   I2C_FUNC_SMBUS_READ_BYTE_DATA)) {
+		pdev->smb_read = idt_smb_read_byte;
+		dev_warn(dev, "Use slow byte SMBus read op");
+	} else /* no supported smbus read operations */ {
+		dev_err(dev, "No supported SMBus read op");
+		return -EPFNOSUPPORT;
+	}
+
+	/* Check i2c adapter write functionality */
+	if (i2c_check_functionality(adapter,
+				    I2C_FUNC_SMBUS_WRITE_BLOCK_DATA)) {
+		pdev->smb_write = idt_smb_write_block;
+		dev_dbg(dev, "SMBus block-write op chosen");
+	} else if (i2c_check_functionality(adapter,
+					   I2C_FUNC_SMBUS_WRITE_I2C_BLOCK)) {
+		pdev->smb_write = idt_smb_write_i2c_block;
+		dev_dbg(dev, "SMBus i2c-block-write op chosen");
+	} else if (i2c_check_functionality(adapter,
+					   I2C_FUNC_SMBUS_WRITE_WORD_DATA) &&
+		   i2c_check_functionality(adapter,
+					   I2C_FUNC_SMBUS_WRITE_BYTE_DATA)) {
+		pdev->smb_write = idt_smb_write_word;
+		dev_warn(dev, "Use slow word/byte SMBus write op");
+	} else if (i2c_check_functionality(adapter,
+					   I2C_FUNC_SMBUS_WRITE_BYTE_DATA)) {
+		pdev->smb_write = idt_smb_write_byte;
+		dev_warn(dev, "Use slow byte SMBus write op");
+	} else /* no supported smbus write operations */ {
+		dev_err(dev, "No supported SMBus write op");
+		return -EPFNOSUPPORT;
+	}
+
+	/* Initialize IDT SMBus slave interface mutex */
+	mutex_init(&pdev->smb_mtx);
+
+	return 0;
+}
+
+/*
+ * idt_check_dev() - check whether it's really IDT 89HPESx device
+ * @pdev:	Pointer to the driver data
+ * Return status of i2c adapter check operation
+ */
+static int idt_check_dev(struct idt_89hpesx_dev *pdev)
+{
+	struct device *dev = &pdev->client->dev;
+	u32 viddid;
+	int ret;
+
+	/* Read VID and DID directly from IDT memory space */
+	ret = idt_csr_read(pdev, IDT_VIDDID_CSR, &viddid);
+	if (ret != 0) {
+		dev_err(dev, "Failed to read VID/DID");
+		return ret;
+	}
+
+	/* Check whether it's IDT device */
+	if ((viddid & IDT_VID_MASK) != PCI_VENDOR_ID_IDT) {
+		dev_err(dev, "Got unsupported VID/DID: 0x%08x", viddid);
+		return -ENODEV;
+	}
+
+	dev_info(dev, "Found IDT 89HPES device VID:0x%04x, DID:0x%04x",
+		(viddid & IDT_VID_MASK), (viddid >> 16));
+
+	return 0;
+}
+
+/*
+ * idt_create_sysfs_files() - create sysfs attribute files
+ * @pdev:	Pointer to the driver data
+ * Return status of operation
+ */
+static int idt_create_sysfs_files(struct idt_89hpesx_dev *pdev)
+{
+	struct device *dev = &pdev->client->dev;
+	int ret;
+
+	/* Don't do anything if EEPROM isn't accessible */
+	if (pdev->eesize == 0) {
+		dev_dbg(dev, "Skip creating sysfs-files");
+		return 0;
+	}
+
+	/*
+	 * Allocate memory for attribute file and copy the declared EEPROM attr
+	 * structure to change some of fields
+	 */
+	pdev->ee_file = devm_kmemdup(dev, &bin_attr_eeprom,
+				     sizeof(*pdev->ee_file), GFP_KERNEL);
+	if (!pdev->ee_file)
+		return -ENOMEM;
+
+	/* In case of read-only EEPROM get rid of write ability */
+	if (pdev->eero) {
+		pdev->ee_file->attr.mode &= ~0200;
+		pdev->ee_file->write = NULL;
+	}
+	/* Create EEPROM sysfs file */
+	pdev->ee_file->size = pdev->eesize;
+	ret = sysfs_create_bin_file(&dev->kobj, pdev->ee_file);
+	if (ret != 0) {
+		dev_err(dev, "Failed to create EEPROM sysfs-node");
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * idt_remove_sysfs_files() - remove sysfs attribute files
+ * @pdev:	Pointer to the driver data
+ */
+static void idt_remove_sysfs_files(struct idt_89hpesx_dev *pdev)
+{
+	struct device *dev = &pdev->client->dev;
+
+	/* Don't do anything if EEPROM wasn't accessible */
+	if (pdev->eesize == 0)
+		return;
+
+	/* Remove EEPROM sysfs file */
+	sysfs_remove_bin_file(&dev->kobj, pdev->ee_file);
+}
+
+/*
+ * idt_probe() - IDT 89HPESx driver probe() callback method
+ */
+static int idt_probe(struct i2c_client *client)
+{
+	struct idt_89hpesx_dev *pdev;
+	int ret;
+
+	/* Create driver data */
+	pdev = idt_create_pdev(client);
+	if (IS_ERR(pdev))
+		return PTR_ERR(pdev);
+
+	/* Set SMBus operations */
+	ret = idt_set_smbus_ops(pdev);
+	if (ret != 0)
+		goto err_free_pdev;
+
+	/* Check whether it is truly IDT 89HPESx device */
+	ret = idt_check_dev(pdev);
+	if (ret != 0)
+		goto err_free_pdev;
+
+	/* Create sysfs files */
+	ret = idt_create_sysfs_files(pdev);
+	if (ret != 0)
+		goto err_free_pdev;
+
+	/* Create debugfs files */
+	debugfs_create_file(pdev->client->name, 0600, client->debugfs, pdev, &csr_dbgfs_ops);
+
+	return 0;
+
+err_free_pdev:
+	idt_free_pdev(pdev);
+
+	return ret;
+}
+
+/*
+ * idt_remove() - IDT 89HPESx driver remove() callback method
+ */
+static void idt_remove(struct i2c_client *client)
+{
+	struct idt_89hpesx_dev *pdev = i2c_get_clientdata(client);
+
+	/* Remove sysfs files */
+	idt_remove_sysfs_files(pdev);
+
+	/* Discard driver data structure */
+	idt_free_pdev(pdev);
+}
+
+/*
+ * ee_ids - array of supported EEPROMs
+ */
+static const struct i2c_device_id ee_ids[] = {
+	{ .name = "24c32", .driver_data = 4096 },
+	{ .name = "24c64", .driver_data = 8192 },
+	{ .name = "24c128", .driver_data = 16384 },
+	{ .name = "24c256", .driver_data = 32768 },
+	{ .name = "24c512", .driver_data = 65536 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, ee_ids);
+
+/*
+ * idt_ids - supported IDT 89HPESx devices
+ */
+static const struct i2c_device_id idt_ids[] = {
+	{ .name = "89hpes8nt2" },
+	{ .name = "89hpes12nt3" },
+
+	{ .name = "89hpes24nt6ag2" },
+	{ .name = "89hpes32nt8ag2" },
+	{ .name = "89hpes32nt8bg2" },
+	{ .name = "89hpes12nt12g2" },
+	{ .name = "89hpes16nt16g2" },
+	{ .name = "89hpes24nt24g2" },
+	{ .name = "89hpes32nt24ag2" },
+	{ .name = "89hpes32nt24bg2" },
+
+	{ .name = "89hpes12n3" },
+	{ .name = "89hpes12n3a" },
+	{ .name = "89hpes24n3" },
+	{ .name = "89hpes24n3a" },
+
+	{ .name = "89hpes32h8" },
+	{ .name = "89hpes32h8g2" },
+	{ .name = "89hpes48h12" },
+	{ .name = "89hpes48h12g2" },
+	{ .name = "89hpes48h12ag2" },
+	{ .name = "89hpes16h16" },
+	{ .name = "89hpes22h16" },
+	{ .name = "89hpes22h16g2" },
+	{ .name = "89hpes34h16" },
+	{ .name = "89hpes34h16g2" },
+	{ .name = "89hpes64h16" },
+	{ .name = "89hpes64h16g2" },
+	{ .name = "89hpes64h16ag2" },
+
+	/* { .name = "89hpes3t3" }, // No SMBus-slave iface */
+	{ .name = "89hpes12t3g2" },
+	{ .name = "89hpes24t3g2" },
+	/* { .name = "89hpes4t4" }, // No SMBus-slave iface */
+	{ .name = "89hpes16t4" },
+	{ .name = "89hpes4t4g2" },
+	{ .name = "89hpes10t4g2" },
+	{ .name = "89hpes16t4g2" },
+	{ .name = "89hpes16t4ag2" },
+	{ .name = "89hpes5t5" },
+	{ .name = "89hpes6t5" },
+	{ .name = "89hpes8t5" },
+	{ .name = "89hpes8t5a" },
+	{ .name = "89hpes24t6" },
+	{ .name = "89hpes6t6g2" },
+	{ .name = "89hpes24t6g2" },
+	{ .name = "89hpes16t7" },
+	{ .name = "89hpes32t8" },
+	{ .name = "89hpes32t8g2" },
+	{ .name = "89hpes48t12" },
+	{ .name = "89hpes48t12g2" },
+	{ /* END OF LIST */ }
+};
+MODULE_DEVICE_TABLE(i2c, idt_ids);
+
+static const struct of_device_id idt_of_match[] = {
+	{ .compatible = "idt,89hpes8nt2" },
+	{ .compatible = "idt,89hpes12nt3" },
+
+	{ .compatible = "idt,89hpes24nt6ag2" },
+	{ .compatible = "idt,89hpes32nt8ag2" },
+	{ .compatible = "idt,89hpes32nt8bg2" },
+	{ .compatible = "idt,89hpes12nt12g2" },
+	{ .compatible = "idt,89hpes16nt16g2" },
+	{ .compatible = "idt,89hpes24nt24g2" },
+	{ .compatible = "idt,89hpes32nt24ag2" },
+	{ .compatible = "idt,89hpes32nt24bg2" },
+
+	{ .compatible = "idt,89hpes12n3" },
+	{ .compatible = "idt,89hpes12n3a" },
+	{ .compatible = "idt,89hpes24n3" },
+	{ .compatible = "idt,89hpes24n3a" },
+
+	{ .compatible = "idt,89hpes32h8" },
+	{ .compatible = "idt,89hpes32h8g2" },
+	{ .compatible = "idt,89hpes48h12" },
+	{ .compatible = "idt,89hpes48h12g2" },
+	{ .compatible = "idt,89hpes48h12ag2" },
+	{ .compatible = "idt,89hpes16h16" },
+	{ .compatible = "idt,89hpes22h16" },
+	{ .compatible = "idt,89hpes22h16g2" },
+	{ .compatible = "idt,89hpes34h16" },
+	{ .compatible = "idt,89hpes34h16g2" },
+	{ .compatible = "idt,89hpes64h16" },
+	{ .compatible = "idt,89hpes64h16g2" },
+	{ .compatible = "idt,89hpes64h16ag2" },
+
+	{ .compatible = "idt,89hpes12t3g2" },
+	{ .compatible = "idt,89hpes24t3g2" },
+
+	{ .compatible = "idt,89hpes16t4" },
+	{ .compatible = "idt,89hpes4t4g2" },
+	{ .compatible = "idt,89hpes10t4g2" },
+	{ .compatible = "idt,89hpes16t4g2" },
+	{ .compatible = "idt,89hpes16t4ag2" },
+	{ .compatible = "idt,89hpes5t5" },
+	{ .compatible = "idt,89hpes6t5" },
+	{ .compatible = "idt,89hpes8t5" },
+	{ .compatible = "idt,89hpes8t5a" },
+	{ .compatible = "idt,89hpes24t6" },
+	{ .compatible = "idt,89hpes6t6g2" },
+	{ .compatible = "idt,89hpes24t6g2" },
+	{ .compatible = "idt,89hpes16t7" },
+	{ .compatible = "idt,89hpes32t8" },
+	{ .compatible = "idt,89hpes32t8g2" },
+	{ .compatible = "idt,89hpes48t12" },
+	{ .compatible = "idt,89hpes48t12g2" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, idt_of_match);
+
+/*
+ * idt_driver - IDT 89HPESx driver structure
+ */
+static struct i2c_driver idt_driver = {
+	.driver = {
+		.name = IDT_NAME,
+		.of_match_table = idt_of_match,
+	},
+	.probe = idt_probe,
+	.remove = idt_remove,
+	.id_table = idt_ids,
+};
+module_i2c_driver(idt_driver);
diff --git a/drivers/misc/eeprom/max6875.c b/drivers/misc/eeprom/max6875.c
new file mode 100644
index 000000000..be5e6d19b
--- /dev/null
+++ b/drivers/misc/eeprom/max6875.c
@@ -0,0 +1,204 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * max6875.c - driver for MAX6874/MAX6875
+ *
+ * Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com>
+ *
+ * Based on eeprom.c
+ *
+ * The MAX6875 has a bank of registers and two banks of EEPROM.
+ * Address ranges are defined as follows:
+ *  * 0x0000 - 0x0046 = configuration registers
+ *  * 0x8000 - 0x8046 = configuration EEPROM
+ *  * 0x8100 - 0x82FF = user EEPROM
+ *
+ * This driver makes the user EEPROM available for read.
+ *
+ * The registers & config EEPROM should be accessed via i2c-dev.
+ *
+ * The MAX6875 ignores the lowest address bit, so each chip responds to
+ * two addresses - 0x50/0x51 and 0x52/0x53.
+ *
+ * Note that the MAX6875 uses i2c_smbus_write_byte_data() to set the read
+ * address, so this driver is destructive if loaded for the wrong EEPROM chip.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/mutex.h>
+
+/* The MAX6875 can only read/write 16 bytes at a time */
+#define SLICE_SIZE			16
+#define SLICE_BITS			4
+
+/* USER EEPROM is at addresses 0x8100 - 0x82FF */
+#define USER_EEPROM_BASE		0x8100
+#define USER_EEPROM_SIZE		0x0200
+#define USER_EEPROM_SLICES		32
+
+/* MAX6875 commands */
+#define MAX6875_CMD_BLK_READ		0x84
+
+/* Each client has this additional data */
+struct max6875_data {
+	struct i2c_client	*fake_client;
+	struct mutex		update_lock;
+
+	u32			valid;
+	u8			data[USER_EEPROM_SIZE];
+	unsigned long		last_updated[USER_EEPROM_SLICES];
+};
+
+static void max6875_update_slice(struct i2c_client *client, int slice)
+{
+	struct max6875_data *data = i2c_get_clientdata(client);
+	int i, j, addr;
+	u8 *buf;
+
+	if (slice >= USER_EEPROM_SLICES)
+		return;
+
+	mutex_lock(&data->update_lock);
+
+	buf = &data->data[slice << SLICE_BITS];
+
+	if (!(data->valid & (1 << slice)) ||
+	    time_after(jiffies, data->last_updated[slice])) {
+
+		dev_dbg(&client->dev, "Starting update of slice %u\n", slice);
+
+		data->valid &= ~(1 << slice);
+
+		addr = USER_EEPROM_BASE + (slice << SLICE_BITS);
+
+		/* select the eeprom address */
+		if (i2c_smbus_write_byte_data(client, addr >> 8, addr & 0xFF)) {
+			dev_err(&client->dev, "address set failed\n");
+			goto exit_up;
+		}
+
+		if (i2c_check_functionality(client->adapter,
+					    I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
+			if (i2c_smbus_read_i2c_block_data(client,
+							  MAX6875_CMD_BLK_READ,
+							  SLICE_SIZE,
+							  buf) != SLICE_SIZE) {
+				goto exit_up;
+			}
+		} else {
+			for (i = 0; i < SLICE_SIZE; i++) {
+				j = i2c_smbus_read_byte(client);
+				if (j < 0) {
+					goto exit_up;
+				}
+				buf[i] = j;
+			}
+		}
+		data->last_updated[slice] = jiffies;
+		data->valid |= (1 << slice);
+	}
+exit_up:
+	mutex_unlock(&data->update_lock);
+}
+
+static ssize_t max6875_read(struct file *filp, struct kobject *kobj,
+			    const struct bin_attribute *bin_attr,
+			    char *buf, loff_t off, size_t count)
+{
+	struct i2c_client *client = kobj_to_i2c_client(kobj);
+	struct max6875_data *data = i2c_get_clientdata(client);
+	int slice, max_slice;
+
+	/* refresh slices which contain requested bytes */
+	max_slice = (off + count - 1) >> SLICE_BITS;
+	for (slice = (off >> SLICE_BITS); slice <= max_slice; slice++)
+		max6875_update_slice(client, slice);
+
+	memcpy(buf, &data->data[off], count);
+
+	return count;
+}
+
+static const struct bin_attribute user_eeprom_attr = {
+	.attr = {
+		.name = "eeprom",
+		.mode = S_IRUGO,
+	},
+	.size = USER_EEPROM_SIZE,
+	.read = max6875_read,
+};
+
+static int max6875_probe(struct i2c_client *client)
+{
+	struct i2c_adapter *adapter = client->adapter;
+	struct max6875_data *data;
+	int err;
+
+	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WRITE_BYTE_DATA
+				     | I2C_FUNC_SMBUS_READ_BYTE))
+		return -ENODEV;
+
+	/* Only bind to even addresses */
+	if (client->addr & 1)
+		return -ENODEV;
+
+	data = kzalloc_obj(struct max6875_data);
+	if (!data)
+		return -ENOMEM;
+
+	/* A fake client is created on the odd address */
+	data->fake_client = i2c_new_dummy_device(client->adapter, client->addr + 1);
+	if (IS_ERR(data->fake_client)) {
+		err = PTR_ERR(data->fake_client);
+		goto exit_kfree;
+	}
+
+	/* Init real i2c_client */
+	i2c_set_clientdata(client, data);
+	mutex_init(&data->update_lock);
+
+	err = sysfs_create_bin_file(&client->dev.kobj, &user_eeprom_attr);
+	if (err)
+		goto exit_remove_fake;
+
+	return 0;
+
+exit_remove_fake:
+	i2c_unregister_device(data->fake_client);
+exit_kfree:
+	kfree(data);
+	return err;
+}
+
+static void max6875_remove(struct i2c_client *client)
+{
+	struct max6875_data *data = i2c_get_clientdata(client);
+
+	i2c_unregister_device(data->fake_client);
+
+	sysfs_remove_bin_file(&client->dev.kobj, &user_eeprom_attr);
+	kfree(data);
+}
+
+static const struct i2c_device_id max6875_id[] = {
+	{ .name = "max6875" },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, max6875_id);
+
+static struct i2c_driver max6875_driver = {
+	.driver = {
+		.name	= "max6875",
+	},
+	.probe		= max6875_probe,
+	.remove		= max6875_remove,
+	.id_table	= max6875_id,
+};
+
+module_i2c_driver(max6875_driver);
+
+MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>");
+MODULE_DESCRIPTION("MAX6875 driver");
+MODULE_LICENSE("GPL");