drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validationgrafted

amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and
uses the first encoding that validates. YCbCr 4:4:4 is listed before
RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the
"color format" property is left at AUTO, even though RGB fits the same
link.

That contradicts the documented AUTO behaviour for HDMI in enum
drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when
the bandwidth is not available or the mode is 4:2:0-only), which the
amdgpu implementation of the property also describes. It also leaves
the "Broadcast RGB" property without effect on such sinks, since the
quantization range it selects only applies to RGB output.

Try RGB first. The mask still holds every encoding the sink supports,
so a mode that cannot carry RGB falls back exactly as before.

For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced
through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI
sink that advertised it.

Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation")
Suggested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Assisted-by: Claude Code:claude-fable-5-1
Signed-off-by: Adrian Betschart <adrian.betschart@cinemaone.ch>
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7)

1 files changed, 48 insertions, 0 deletions

diff --git a/drivers/misc/eeprom/Kconfig b/drivers/misc/eeprom/Kconfig
new file mode 100644
index 000000000..d6af02588
--- /dev/null
+++ b/drivers/misc/eeprom/Kconfig
@@ -0,0 +1,48 @@
+# SPDX-License-Identifier: GPL-2.0-only
+menu "EEPROM support"
+
+config EEPROM_MAX6875
+	tristate "Maxim MAX6874/5 power supply supervisor"
+	depends on I2C
+	help
+	  If you say yes here you get read-only support for the user EEPROM of
+	  the Maxim MAX6874/5 EEPROM-programmable, quad power-supply
+	  sequencer/supervisor.
+
+	  All other features of this chip should be accessed via i2c-dev.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called max6875.
+
+
+config EEPROM_93CX6
+	tristate "EEPROM 93CX6 support"
+	help
+	  This is a driver for the EEPROM chipsets 93c46 and 93c66.
+	  The driver supports both read as well as write commands.
+
+	  If unsure, say N.
+
+config EEPROM_DIGSY_MTC_CFG
+	bool "DigsyMTC display configuration EEPROMs device"
+	depends on GPIO_MPC5200 && SPI_GPIO
+	help
+	  This option enables access to display configuration EEPROMs
+	  on digsy_mtc board. You have to additionally select Microwire
+	  EEPROM 93XX46 driver. sysfs entries will be created for that
+	  EEPROM allowing to read/write the configuration data or to
+	  erase the whole EEPROM.
+
+	  If unsure, say N.
+
+config EEPROM_IDT_89HPESX
+	tristate "IDT 89HPESx PCIe-switches EEPROM / CSR support"
+	depends on I2C && SYSFS
+	help
+	  Enable this driver to get read/write access to EEPROM / CSRs
+	  over IDT PCIe-switch i2c-slave interface.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called idt_89hpesx.
+
+endmenu