drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validationgrafted

amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and
uses the first encoding that validates. YCbCr 4:4:4 is listed before
RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the
"color format" property is left at AUTO, even though RGB fits the same
link.

That contradicts the documented AUTO behaviour for HDMI in enum
drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when
the bandwidth is not available or the mode is 4:2:0-only), which the
amdgpu implementation of the property also describes. It also leaves
the "Broadcast RGB" property without effect on such sinks, since the
quantization range it selects only applies to RGB output.

Try RGB first. The mask still holds every encoding the sink supports,
so a mode that cannot carry RGB falls back exactly as before.

For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced
through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI
sink that advertised it.

Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation")
Suggested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Assisted-by: Claude Code:claude-fable-5-1
Signed-off-by: Adrian Betschart <adrian.betschart@cinemaone.ch>
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7)

1 files changed, 126 insertions, 0 deletions

diff --git a/drivers/mfd/viperboard.c b/drivers/mfd/viperboard.c
new file mode 100644
index 000000000..36be8e69f
--- /dev/null
+++ b/drivers/mfd/viperboard.c
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  Nano River Technologies viperboard driver
+ *
+ *  This is the core driver for the viperboard. There are cell drivers
+ *  available for I2C, ADC and both GPIOs. SPI is not yet supported.
+ *  The drivers do not support all features the board exposes. See user
+ *  manual of the viperboard.
+ *
+ *  (C) 2012 by Lemonage GmbH
+ *  Author: Lars Poeschel <poeschel@lemonage.de>
+ *  All rights reserved.
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/mutex.h>
+
+#include <linux/mfd/core.h>
+#include <linux/mfd/viperboard.h>
+
+#include <linux/usb.h>
+
+
+static const struct usb_device_id vprbrd_table[] = {
+	{ USB_DEVICE(0x2058, 0x1005) },   /* Nano River Technologies */
+	{ }                               /* Terminating entry */
+};
+
+MODULE_DEVICE_TABLE(usb, vprbrd_table);
+
+static const struct mfd_cell vprbrd_devs[] = {
+	{
+		.name = "viperboard-gpio",
+	},
+	{
+		.name = "viperboard-i2c",
+	},
+	{
+		.name = "viperboard-adc",
+	},
+};
+
+static int vprbrd_probe(struct usb_interface *interface,
+			      const struct usb_device_id *id)
+{
+	struct vprbrd *vb;
+
+	u16 version = 0;
+	int pipe, ret;
+
+	/* allocate memory for our device state and initialize it */
+	vb = kzalloc_obj(*vb);
+	if (!vb)
+		return -ENOMEM;
+
+	mutex_init(&vb->lock);
+
+	vb->usb_dev = interface_to_usbdev(interface);
+
+	/* save our data pointer in this interface device */
+	usb_set_intfdata(interface, vb);
+	dev_set_drvdata(&vb->pdev.dev, vb);
+
+	/* get version information, major first, minor then */
+	pipe = usb_rcvctrlpipe(vb->usb_dev, 0);
+	ret = usb_control_msg(vb->usb_dev, pipe, VPRBRD_USB_REQUEST_MAJOR,
+		VPRBRD_USB_TYPE_IN, 0x0000, 0x0000, vb->buf, 1,
+		VPRBRD_USB_TIMEOUT_MS);
+	if (ret == 1)
+		version = vb->buf[0];
+
+	ret = usb_control_msg(vb->usb_dev, pipe, VPRBRD_USB_REQUEST_MINOR,
+		VPRBRD_USB_TYPE_IN, 0x0000, 0x0000, vb->buf, 1,
+		VPRBRD_USB_TIMEOUT_MS);
+	if (ret == 1) {
+		version <<= 8;
+		version = version | vb->buf[0];
+	}
+
+	dev_info(&interface->dev,
+		 "version %x.%02x found at bus %03d address %03d\n",
+		 version >> 8, version & 0xff,
+		 vb->usb_dev->bus->busnum, vb->usb_dev->devnum);
+
+	ret = mfd_add_hotplug_devices(&interface->dev, vprbrd_devs,
+				      ARRAY_SIZE(vprbrd_devs));
+	if (ret != 0) {
+		dev_err(&interface->dev, "Failed to add mfd devices to core.");
+		goto error;
+	}
+
+	return 0;
+
+error:
+	kfree(vb);
+
+	return ret;
+}
+
+static void vprbrd_disconnect(struct usb_interface *interface)
+{
+	struct vprbrd *vb = usb_get_intfdata(interface);
+
+	mfd_remove_devices(&interface->dev);
+	usb_set_intfdata(interface, NULL);
+	kfree(vb);
+
+	dev_dbg(&interface->dev, "disconnected\n");
+}
+
+static struct usb_driver vprbrd_driver = {
+	.name		= "viperboard",
+	.probe		= vprbrd_probe,
+	.disconnect	= vprbrd_disconnect,
+	.id_table	= vprbrd_table,
+};
+
+module_usb_driver(vprbrd_driver);
+
+MODULE_DESCRIPTION("Nano River Technologies viperboard mfd core driver");
+MODULE_AUTHOR("Lars Poeschel <poeschel@lemonage.de>");
+MODULE_LICENSE("GPL");