openrisc: fix arbitrary kernel memory access via or1k_atomic syscallgrafted

sys_or1k_atomic() (syscall 244 in the "or1k" ABI) takes two user
pointers, v1 and v2, and swaps the words they point to in hand-written
assembly.

    l.lwz   r29,0(r4)
    l.lwz   r27,0(r5)
    l.sw    0(r4),r27
    l.sw    0(r5),r29

The pointers are not checked with access_ok(). The four memory
accesses also have no exception table entries.

A caller passes a kernel address as either pointer, and the syscall
reads from and writes to it directly.

This gives an unprivileged process a kernel read/write primitive. It
overwrites kernel data such as the sys_call_table, gaining code
execution in kernel context.

Check both pointers before entering the critical section. Add fixups
for the four memory accesses so faults on valid but unmapped user
addresses return -EFAULT.

[shorne@gmail.com: fix comment style]
Fixes: 9d02a4283e9c ("OpenRISC: Boot code")
Cc: stable@vger.kernel.org
Signed-off-by: Ali Ahmet Memis <ali@iusegentoo.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>

1 files changed, 186 insertions, 0 deletions

diff --git a/drivers/input/touchscreen/inexio.c b/drivers/input/touchscreen/inexio.c
new file mode 100644
index 000000000..ac3836ff2
--- /dev/null
+++ b/drivers/input/touchscreen/inexio.c
@@ -0,0 +1,186 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * iNexio serial touchscreen driver
+ *
+ * Copyright (c) 2008 Richard Lemon
+ * Based on the mtouch driver (c) Vojtech Pavlik and Dan Streetman
+ */
+
+
+/*
+ * 2008/06/19 Richard Lemon <richard@codelemon.com>
+ *   Copied mtouch.c and edited for iNexio protocol
+ */
+
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/input.h>
+#include <linux/serio.h>
+
+#define DRIVER_DESC	"iNexio serial touchscreen driver"
+
+MODULE_AUTHOR("Richard Lemon <richard@codelemon.com>");
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
+
+/*
+ * Definitions & global arrays.
+ */
+
+#define INEXIO_FORMAT_TOUCH_BIT 0x01
+#define INEXIO_FORMAT_LENGTH 5
+#define INEXIO_RESPONSE_BEGIN_BYTE 0x80
+
+/* todo: check specs for max length of all responses */
+#define INEXIO_MAX_LENGTH 16
+
+#define INEXIO_MIN_XC 0
+#define INEXIO_MAX_XC 0x3fff
+#define INEXIO_MIN_YC 0
+#define INEXIO_MAX_YC 0x3fff
+
+#define INEXIO_GET_XC(data) (((data[1])<<7) | data[2])
+#define INEXIO_GET_YC(data) (((data[3])<<7) | data[4])
+#define INEXIO_GET_TOUCHED(data) (INEXIO_FORMAT_TOUCH_BIT & data[0])
+
+/*
+ * Per-touchscreen data.
+ */
+
+struct inexio {
+	struct input_dev *dev;
+	struct serio *serio;
+	int idx;
+	unsigned char data[INEXIO_MAX_LENGTH];
+	char phys[32];
+};
+
+static void inexio_process_data(struct inexio *pinexio)
+{
+	struct input_dev *dev = pinexio->dev;
+
+	if (INEXIO_FORMAT_LENGTH == ++pinexio->idx) {
+		input_report_abs(dev, ABS_X, INEXIO_GET_XC(pinexio->data));
+		input_report_abs(dev, ABS_Y, INEXIO_GET_YC(pinexio->data));
+		input_report_key(dev, BTN_TOUCH, INEXIO_GET_TOUCHED(pinexio->data));
+		input_sync(dev);
+
+		pinexio->idx = 0;
+	}
+}
+
+static irqreturn_t inexio_interrupt(struct serio *serio,
+		unsigned char data, unsigned int flags)
+{
+	struct inexio *pinexio = serio_get_drvdata(serio);
+
+	pinexio->data[pinexio->idx] = data;
+
+	if (INEXIO_RESPONSE_BEGIN_BYTE&pinexio->data[0])
+		inexio_process_data(pinexio);
+	else
+		printk(KERN_DEBUG "inexio.c: unknown/unsynchronized data from device, byte %x\n",pinexio->data[0]);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * inexio_disconnect() is the opposite of inexio_connect()
+ */
+
+static void inexio_disconnect(struct serio *serio)
+{
+	struct inexio *pinexio = serio_get_drvdata(serio);
+
+	input_get_device(pinexio->dev);
+	input_unregister_device(pinexio->dev);
+	serio_close(serio);
+	serio_set_drvdata(serio, NULL);
+	input_put_device(pinexio->dev);
+	kfree(pinexio);
+}
+
+/*
+ * inexio_connect() is the routine that is called when someone adds a
+ * new serio device that supports iNexio protocol and registers it as
+ * an input device. This is usually accomplished using inputattach.
+ */
+
+static int inexio_connect(struct serio *serio, struct serio_driver *drv)
+{
+	struct inexio *pinexio;
+	struct input_dev *input_dev;
+	int err;
+
+	pinexio = kzalloc_obj(*pinexio);
+	input_dev = input_allocate_device();
+	if (!pinexio || !input_dev) {
+		err = -ENOMEM;
+		goto fail1;
+	}
+
+	pinexio->serio = serio;
+	pinexio->dev = input_dev;
+	scnprintf(pinexio->phys, sizeof(pinexio->phys), "%s/input0", serio->phys);
+
+	input_dev->name = "iNexio Serial TouchScreen";
+	input_dev->phys = pinexio->phys;
+	input_dev->id.bustype = BUS_RS232;
+	input_dev->id.vendor = SERIO_INEXIO;
+	input_dev->id.product = 0;
+	input_dev->id.version = 0x0001;
+	input_dev->dev.parent = &serio->dev;
+	input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
+	input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
+	input_set_abs_params(pinexio->dev, ABS_X, INEXIO_MIN_XC, INEXIO_MAX_XC, 0, 0);
+	input_set_abs_params(pinexio->dev, ABS_Y, INEXIO_MIN_YC, INEXIO_MAX_YC, 0, 0);
+
+	serio_set_drvdata(serio, pinexio);
+
+	err = serio_open(serio, drv);
+	if (err)
+		goto fail2;
+
+	err = input_register_device(pinexio->dev);
+	if (err)
+		goto fail3;
+
+	return 0;
+
+ fail3:	serio_close(serio);
+ fail2:	serio_set_drvdata(serio, NULL);
+ fail1:	input_free_device(input_dev);
+	kfree(pinexio);
+	return err;
+}
+
+/*
+ * The serio driver structure.
+ */
+
+static const struct serio_device_id inexio_serio_ids[] = {
+	{
+		.type	= SERIO_RS232,
+		.proto	= SERIO_INEXIO,
+		.id	= SERIO_ANY,
+		.extra	= SERIO_ANY,
+	},
+	{ 0 }
+};
+
+MODULE_DEVICE_TABLE(serio, inexio_serio_ids);
+
+static struct serio_driver inexio_drv = {
+	.driver		= {
+		.name	= "inexio",
+	},
+	.description	= DRIVER_DESC,
+	.id_table	= inexio_serio_ids,
+	.interrupt	= inexio_interrupt,
+	.connect	= inexio_connect,
+	.disconnect	= inexio_disconnect,
+};
+
+module_serio_driver(inexio_drv);