drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validationgrafted

amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and
uses the first encoding that validates. YCbCr 4:4:4 is listed before
RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the
"color format" property is left at AUTO, even though RGB fits the same
link.

That contradicts the documented AUTO behaviour for HDMI in enum
drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when
the bandwidth is not available or the mode is 4:2:0-only), which the
amdgpu implementation of the property also describes. It also leaves
the "Broadcast RGB" property without effect on such sinks, since the
quantization range it selects only applies to RGB output.

Try RGB first. The mask still holds every encoding the sink supports,
so a mode that cannot carry RGB falls back exactly as before.

For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced
through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI
sink that advertised it.

Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation")
Suggested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Assisted-by: Claude Code:claude-fable-5-1
Signed-off-by: Adrian Betschart <adrian.betschart@cinemaone.ch>
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7)

1 files changed, 256 insertions, 0 deletions

diff --git a/drivers/gpib/Kconfig b/drivers/gpib/Kconfig
new file mode 100644
index 000000000..d43a28c62
--- /dev/null
+++ b/drivers/gpib/Kconfig
@@ -0,0 +1,256 @@
+# SPDX-License-Identifier: GPL-2.0
+menuconfig GPIB
+	tristate "GPIB drivers"
+	help
+	  Enable support for GPIB cards and dongles.  GPIB is the
+	  General Purpose Interface Bus which conforms to the IEEE488
+	  standard.
+
+	  This set of drivers can be used with the corresponding user
+	  space library that can be found on Sourceforge under linux-gpib.
+	  Select the drivers for your hardware from the list.
+
+if GPIB
+
+config GPIB_COMMON
+	tristate "GPIB core"
+	help
+
+	  Core common driver for all GPIB drivers. It provides the
+	  interface for the userland library
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called gpib_common
+
+config GPIB_AGILENT_82350B
+	tristate "Agilent 8235xx PCI(e) adapters"
+	depends on PCI
+	select GPIB_COMMON
+	select GPIB_TMS9914
+	help
+	  Enable support for HP/Agilent/Keysight boards
+	    82350A
+	    82350B
+	    82351A
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called agilent_82350b.
+
+config GPIB_AGILENT_82357A
+	tristate "Agilent 82357a/b USB dongles"
+	select GPIB_COMMON
+	depends on USB
+	help
+	  Enable support for Agilent/Keysight 82357x USB dongles.
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called agilent_82357a.
+
+config GPIB_CEC_PCI
+	tristate "CEC PCI board"
+	depends on PCI
+	depends on HAS_IOPORT
+	select GPIB_COMMON
+	select GPIB_NEC7210
+	help
+	  Enable support for Capital Equipment Corporation PCI-488
+	  and Keithly KPCI-488 boards.
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called cec_gpib.
+
+config GPIB_NI_PCI_ISA
+	tristate "NI PCI/ISA compatible boards"
+	depends on ISA_BUS || PCI || PCMCIA
+	depends on HAS_IOPORT
+	depends on PCMCIA || !PCMCIA
+	depends on HAS_IOPORT_MAP
+	select GPIB_COMMON
+	select GPIB_NEC7210
+	help
+	  Enable support for National Instruments boards based
+	  on TNT4882 chips:
+	     AT-GPIB (with NAT4882 chip)
+	     AT-GPIB (with NEC7210 chip)
+	     AT-GPIB/TNT
+	     PCI-GPIB
+	     PCIe-GPIB
+	     PCI-GPIB+
+	     PCM-GPIB
+	     PXI-GPIB
+	     PCMCIA-GPIB
+	     and Capital Equipment Corporation CEC-488 board.
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called tnt4882.
+
+config GPIB_CB7210
+       tristate "Measurement Computing compatible boards"
+	depends on HAS_IOPORT
+	depends on ISA_BUS || PCI || PCMCIA
+	depends on PCMCIA || !PCMCIA
+       select GPIB_COMMON
+	select GPIB_NEC7210
+       help
+       Enable support for Measurement Computing (Computer Boards):
+       CPCI_GPIB, ISA-GPIB, ISA-GPIB/LC, PCI-GPIB/1M, PCI-GPIB/300K and
+       PCMCIA-GPIB
+       Quancom PCIGPIB-1 with MC cb7210 chip
+
+	  To compile this driver as a module, choose M here: the module will be
+
+config GPIB_NI_USB
+	tristate "NI USB dongles"
+	select GPIB_COMMON
+	depends on USB
+	help
+	  Enable support for National Instruments
+	       GPIB-USB-B
+	       GPIB-USB-HS
+	       GPIB-USB-HS+
+	   Keithly
+	       KUSB-488
+	       KUSB-488A
+	   Measurement Computing (Computer Boards)
+	       USB-488
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called ni_usb.
+
+config GPIB_FLUKE
+       tristate "Fluke"
+	depends on OF
+       select GPIB_COMMON
+       select GPIB_NEC7210
+       depends on HAS_IOMEM
+       help
+         GPIB driver for Fluke based cda devices.
+
+	 To compile this driver as a module, choose M here: the module will be
+	 called fluke_gpib
+
+config GPIB_FMH
+       tristate "FMH FPGA based devices"
+       select GPIB_COMMON
+       select GPIB_NEC7210
+       depends on !PPC
+       depends on OF && PCI
+       help
+         GPIB driver for fmhess FPGA based devices
+
+	 To compile this driver as a module, choose M here: the module will be
+	 called fmh_gpib
+
+config GPIB_GPIO
+       tristate "RPi GPIO bitbang"
+	depends on ARCH_BCM2835 || COMPILE_TEST
+       select GPIB_COMMON
+       help
+         GPIB bitbang driver Raspberry Pi GPIO adapters
+
+	 To compile this driver as a module, choose M here: the module will be
+	 called gpib_bitbang
+
+config GPIB_HP82335
+       tristate "HP82335/HP27209"
+	depends on ISA_BUS
+       select GPIB_COMMON
+       select GPIB_TMS9914
+       help
+         GPIB driver for HP82335 and HP27209 boards
+
+	 To compile this driver as a module, choose M here: the module will be
+	 called hp82335
+
+
+config GPIB_HP82341
+       tristate "HP82341x"
+       select GPIB_COMMON
+       select GPIB_TMS9914
+       depends on ISA_BUS || EISA
+       help
+         GPIB driver for HP82341 A/B/C/D boards
+
+	 To compile this driver as a module, choose M here: the module will be
+	 called hp82341
+
+config GPIB_INES
+       tristate "INES"
+	depends on PCI || ISA_BUS || PCMCIA
+	depends on PCMCIA || !PCMCIA
+	depends on HAS_IOPORT
+       select GPIB_COMMON
+       select GPIB_NEC7210
+       help
+         GPIB driver for Ines compatible boards
+	 Ines
+	    GPIB-HS-NT
+	    GPIB for Compact PCI
+	    GPIB for PCI
+	    GPIB for PCMCIA
+	    GPIB PC/104
+	 Hameg
+	    HO80-2
+	 Quancom
+	    PCIGPIB-1 based on Ines iGPIB 72010 chip
+
+	 To compile this driver as a module, choose M here: the module will be
+	 called ines_gpib
+	  called cb7210.
+
+config GPIB_PCMCIA
+       def_bool y
+       depends on PCMCIA && (GPIB_NI_PCI_ISA || GPIB_CB7210 || GPIB_INES)
+       help
+         Enable PCMCIA/CArdbus support for National Instruments,
+	 measurement computing boards and Ines boards.
+
+config GPIB_LPVO
+       tristate "LPVO DIY USB GPIB"
+       select GPIB_COMMON
+       depends on USB
+       help
+         Enable support for LPVO Self-made usb-gpib adapter
+
+	 To compile this driver as a module, choose M here: the module will be
+	 called lpvo_usb_gpib
+
+config GPIB_PC2
+       tristate "PC2 PC2a"
+	depends on ISA_BUS
+	depends on HAS_IOPORT
+       select GPIB_COMMON
+       select GPIB_NEC7210
+       help
+         Enable support for pc2 and pc2a compatible adapters
+	    Capital Equipment Corporation PC-488
+	    CONTEC GP-IB(PC)
+	    Hameg HO80
+	    Iotech GP488B
+	    Keithly MBC-488
+	    Measurement Computing ISA-GPIB-PCA2
+	    National Instruments PCII, PCIIa and PCII/IIa
+
+	 To compile this driver as a module, choose M here: the module will be
+	 called pc2_gpib
+
+
+config GPIB_TMS9914
+       tristate
+       select GPIB_COMMON
+       help
+         Enable support for TMS 9914 chip.
+
+	 To compile this driver as a module, choose M here: the module will be
+	 called tms9914
+
+config GPIB_NEC7210
+       tristate
+       select GPIB_COMMON
+       help
+         Enable support for NEC 7210 compatible chips.
+
+	 To compile this driver as a module, choose M here: the module will be
+	 called nec7210
+
+endif # GPIB