sched/cache: Keep nr_pref_llc_running in the runnable domain, to fix LLC mis-scheduling buggrafted

alb_break_llc() decides whether to break LLC preference during active
load balance. It does so by testing that every runnable fair task on the
source rq prefers its LLC:

	env->src_rq->nr_pref_llc_running == env->src_rq->cfs.h_nr_runnable

But the two counters cover different sets. nr_pref_llc_running is updated
in account_llc_enqueue()/account_llc_dequeue(), next to cfs_rq->nr_queued,
so it follows queued tasks. h_nr_runnable is updated in set_delayed()/
clear_delayed() and drops delay-dequeued tasks.

So under DELAY_DEQUEUE, a preferring task that goes to sleep stays counted
in nr_pref_llc_running while h_nr_runnable falls. The equality then breaks,
alb_break_llc() returns false, and active balance is free to pull a task
off its preferred LLC. Active balance only moves runnable tasks, and this
is the only LLC check it consults: once the stopper runs, LBF_ACTIVE_LB
skips the per-task test in can_migrate_task(). The runnable set is the one
we want.

Fix it on the counter side. A task should be counted in
nr_pref_llc_running exactly while it is both queued on its preferred LLC
(pref_llc_queued) and runnable (!sched_delayed). Define that membership
once in task_pref_llc_runnable(), and adjust the counter only through
pref_llc_running_inc()/pref_llc_running_dec() from the four sites that
change either input: account_llc_enqueue(), account_llc_dequeue(),
set_delayed() and clear_delayed(). Gating every update on the same
predicate keeps the delay, wake and dequeue paths from double-counting
or underflowing; see the comments at those sites for the ordering.

nr_llc_running and sd->llc_counts are not touched and stay on queued
semantics.

Fixes: 714059f79ff0 ("sched/cache: Handle moving single tasks to/from their preferred LLC")
Closes: https://lore.kernel.org/lkml/20260827135000.735138-1-zhanxusheng@xiaomi.com/
Reported-by: Zhan Xusheng <zhanxusheng@xiaomi.com>
Suggested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kayra Cizmeci <kayracizmeci@gmail.com>
Cc: <stable@kernel.org> # v7.2.x
Link: https://patch.msgid.link/06af61afedac32e6477f57feb4d658f6c411c3af.1790035273.git.tim.c.chen@linux.intel.com

1 files changed, 55 insertions, 0 deletions

diff --git a/drivers/dma/qcom/Kconfig b/drivers/dma/qcom/Kconfig
new file mode 100644
index 000000000..c71b0b5d5
--- /dev/null
+++ b/drivers/dma/qcom/Kconfig
@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config QCOM_ADM
+	tristate "Qualcomm ADM support"
+	depends on (ARCH_QCOM || COMPILE_TEST) && !PHYS_ADDR_T_64BIT
+	select DMA_ENGINE
+	select DMA_VIRTUAL_CHANNELS
+	help
+	  Enable support for the Qualcomm Application Data Mover (ADM) DMA
+	  controller, as present on MSM8x60, APQ8064, and IPQ8064 devices.
+	  This controller provides DMA capabilities for both general purpose
+	  and on-chip peripheral devices.
+
+config QCOM_BAM_DMA
+	tristate "Qualcomm BAM DMA support"
+	depends on ARCH_QCOM || (COMPILE_TEST && OF && ARM)
+	select DMA_ENGINE
+	select DMA_VIRTUAL_CHANNELS
+	help
+	  Enable support for the QCOM BAM DMA controller.  This controller
+	  provides DMA capabilities for a variety of on-chip devices.
+
+config QCOM_GPI_DMA
+        tristate "Qualcomm GPI DMA support"
+        depends on ARCH_QCOM
+        select DMA_ENGINE
+        select DMA_VIRTUAL_CHANNELS
+        help
+          Enable support for the QCOM GPI DMA controller. This controller
+          provides DMA capabilities for a variety of peripheral buses such
+          as I2C, UART, and SPI. By using GPI dmaengine driver, bus drivers
+          can use a standardize interface that is protocol independent to
+          transfer data between DDR and peripheral.
+
+config QCOM_HIDMA_MGMT
+	tristate "Qualcomm HIDMA Management support"
+	depends on HAS_IOMEM
+	select DMA_ENGINE
+	help
+	  Enable support for the Qualcomm Technologies HIDMA Management.
+	  Each DMA device requires one management interface driver
+	  for basic initialization before QCOM_HIDMA channel driver can
+	  start managing the channels. In a virtualized environment,
+	  the guest OS would run QCOM_HIDMA channel driver and the
+	  host would run the QCOM_HIDMA_MGMT management driver.
+
+config QCOM_HIDMA
+	tristate "Qualcomm HIDMA Channel support"
+	depends on HAS_IOMEM
+	select DMA_ENGINE
+	help
+	  Enable support for the Qualcomm Technologies HIDMA controller.
+	  The HIDMA controller supports optimized buffer copies
+	  (user to kernel, kernel to kernel, etc.).  It only supports
+	  memcpy interface. The core is not intended for general
+	  purpose slave DMA.