Merge tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlgrafted

Pull pin control updates from Linus Walleij:
 "Core changes:

   - Use the non-blocking mux_state_try_select() in the generic MUX pin
     control back-end

   - Free pin maps on pinctrl_generic_to_map() failure in the core
     helpers

  New hardware pin control:

   - Qualcomm Maili TLMM SoC, PMG1110 PMIC, and Eliza LPASS LPI TLMM SoC
     (this is for the low power audio, LPASS = Low Power Audio SubSystem
     portions)

   - Upboard support on top of the Intel pin controller

   - Apple T6030 and T6031 support (just compatible strings)

   - Samsung Exynos 8855 SoC

   - Mediatek MT6858 SoC

   - Rockchip RK3308B and RV1106 SoCs

   - Airoha EN7523 and AN7563 SoCs

  Improvements:

   - Qualcomm TLMM GPIOs are unconditionally marked as wakeup capable

   - Qualcomm improvements on top of the Qualcomm PDC (power domain
     controller) irqchip improvements from tglx:s tree

   - Qualcomm IPQ806x and IPQ9650 non-urgent pin grop fixups

   - The NPCM8xx driver has been put into shape fixing many pin and
     group definitions

   - Some non-urgent Tegra 264 pin assignments are fixed up

   - Some non-urgent fixups to Airoha AN7581 and AN7583 registers and
     pin assignments, missing features etc"

* tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (130 commits)
  dt-bindings: pinctrl: Convert TI DA850 pupd to DT schema
  pinctrl: meson: sync some modify from A4
  pinctrl: meson: a4: Add input enable pin configuration
  pinctrl: realtek: rtd1625: remove unused group name spdif_sel
  pinctrl: realtek: rtd1625: fix base_bit for VE4 GPIO 13
  dt-bindings: pinctrl: microchip,pic32mzda-pinctrl: Convert to DT schema
  Revert "Merge branch 'ib-rsk7204' into devel"
  pinctrl: rockchip: Add RV1106 pinctrl support
  dt-bindings: pinctrl: rockchip: Add RV1106 compatible
  pinctrl: rockchip: Decode drive strength in the get function
  pinctrl: fix PINCTRL_GENERIC_MUX not always being selectable
  pinctrl: airoha: add support of an7563 SoC
  dt-bindings: pinctrl: airoha: add support of an7563 pin controller
  pinctrl: airoha: try to find chip scu node by phandle first
  pinctrl: airoha: add support of en7523 SoC
  dt-bindings: pinctrl: airoha: add support of en7523 pin controller
  pinctrl: airoha: an7583: add support for olt pinmux
  pinctrl: airoha: an7583: add support for pon_alt pinmux
  pinctrl: airoha: an7583: add support for npu_uart pinmux
  dt-bindings: pinctrl: airoha: an7583: add missed features
  ...

1 files changed, 374 insertions, 0 deletions

diff --git a/drivers/char/Kconfig b/drivers/char/Kconfig
new file mode 100644
index 000000000..9865227af
--- /dev/null
+++ b/drivers/char/Kconfig
@@ -0,0 +1,374 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Character device configuration
+#
+
+menu "Character devices"
+
+source "drivers/tty/Kconfig"
+
+config TTY_PRINTK
+	tristate "TTY driver to output user messages via printk"
+	depends on EXPERT && TTY
+	default n
+	help
+	  If you say Y here, the support for writing user messages (i.e.
+	  console messages) via printk is available.
+
+	  The feature is useful to inline user messages with kernel
+	  messages.
+	  In order to use this feature, you should output user messages
+	  to /dev/ttyprintk or redirect console to this TTY, or boot
+	  the kernel with console=ttyprintk.
+
+	  If unsure, say N.
+
+config TTY_PRINTK_LEVEL
+	depends on TTY_PRINTK
+	int "ttyprintk log level (1-7)"
+	range 1 7
+	default "6"
+	help
+	  Printk log level to use for ttyprintk messages.
+
+config PRINTER
+	tristate "Parallel printer support"
+	depends on PARPORT
+	depends on HAS_IOPORT || PARPORT_NOT_PC
+	help
+	  If you intend to attach a printer to the parallel port of your Linux
+	  box (as opposed to using a serial printer; if the connector at the
+	  printer has 9 or 25 holes ["female"], then it's serial), say Y.
+	  Also read the Printing-HOWTO, available from
+	  <https://www.tldp.org/docs.html#howto>.
+
+	  It is possible to share one parallel port among several devices
+	  (e.g. printer and ZIP drive) and it is safe to compile the
+	  corresponding drivers into the kernel.
+
+	  To compile this driver as a module, choose M here and read
+	  <file:Documentation/admin-guide/parport.rst>.  The module will be called lp.
+
+	  If you have several parallel ports, you can specify which ports to
+	  use with the "lp" kernel command line option.  (Try "man bootparam"
+	  or see the documentation of your boot loader (lilo or loadlin) about
+	  how to pass options to the kernel at boot time.)  The syntax of the
+	  "lp" command line option can be found in <file:drivers/char/lp.c>.
+
+	  If you have more than 8 printers, you need to increase the LP_NO
+	  macro in lp.c and the PARPORT_MAX macro in parport.h.
+
+config LP_CONSOLE
+	bool "Support for console on line printer"
+	depends on PRINTER
+	help
+	  If you want kernel messages to be printed out as they occur, you
+	  can have a console on the printer. This option adds support for
+	  doing that; to actually get it to happen you need to pass the
+	  option "console=lp0" to the kernel at boot time.
+
+	  If the printer is out of paper (or off, or unplugged, or too
+	  busy..) the kernel will stall until the printer is ready again.
+	  By defining CONSOLE_LP_STRICT to 0 (at your own risk) you
+	  can make the kernel continue when this happens,
+	  but it'll lose the kernel messages.
+
+	  If unsure, say N.
+
+config PPDEV
+	tristate "Support for user-space parallel port device drivers"
+	depends on PARPORT
+	help
+	  Saying Y to this adds support for /dev/parport device nodes.  This
+	  is needed for programs that want portable access to the parallel
+	  port, for instance deviceid (which displays Plug-and-Play device
+	  IDs).
+
+	  This is the parallel port equivalent of SCSI generic support (sg).
+	  It is safe to say N to this -- it is not needed for normal printing
+	  or parallel port CD-ROM/disk support.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ppdev.
+
+	  If unsure, say N.
+
+config VIRTIO_CONSOLE
+	tristate "Virtio console"
+	depends on TTY
+	select HVC_DRIVER
+	select VIRTIO
+	help
+	  Virtio console for use with hypervisors.
+
+	  Also serves as a general-purpose serial device for data
+	  transfer between the guest and host.  Character devices at
+	  /dev/vportNpn will be created when corresponding ports are
+	  found, where N is the device number and n is the port number
+	  within that device.  If specified by the host, a sysfs
+	  attribute called 'name' will be populated with a name for
+	  the port which can be used by udev scripts to create a
+	  symlink to the device.
+
+config IBM_BSR
+	tristate "IBM POWER Barrier Synchronization Register support"
+	depends on PPC_PSERIES
+	help
+	  This devices exposes a hardware mechanism for fast synchronization
+	  of threads across a large system which avoids bouncing a cacheline
+	  between several cores on a system
+
+config POWERNV_OP_PANEL
+	tristate "IBM POWERNV Operator Panel Display support"
+	depends on PPC_POWERNV
+	default m
+	help
+	  If you say Y here, a special character device node, /dev/op_panel,
+	  will be created which exposes the operator panel display on IBM
+	  Power Systems machines with FSPs.
+
+	  If you don't require access to the operator panel display from user
+	  space, say N.
+
+	  If unsure, say M here to build it as a module called powernv-op-panel.
+
+source "drivers/char/ipmi/Kconfig"
+
+config DS1620
+	tristate "NetWinder thermometer support"
+	depends on ARCH_NETWINDER
+	help
+	  Say Y here to include support for the thermal management hardware
+	  found in the NetWinder. This driver allows the user to control the
+	  temperature set points and to read the current temperature.
+
+	  It is also possible to say M here to build it as a module (ds1620)
+	  It is recommended to be used on a NetWinder, but it is not a
+	  necessity.
+
+config NWBUTTON
+	tristate "NetWinder Button"
+	depends on ARCH_NETWINDER
+	help
+	  If you say Y here and create a character device node /dev/nwbutton
+	  with major and minor numbers 10 and 158 ("man mknod"), then every
+	  time the orange button is pressed a number of times, the number of
+	  times the button was pressed will be written to that device.
+
+	  This is most useful for applications, as yet unwritten, which
+	  perform actions based on how many times the button is pressed in a
+	  row.
+
+	  Do not hold the button down for too long, as the driver does not
+	  alter the behaviour of the hardware reset circuitry attached to the
+	  button; it will still execute a hard reset if the button is held
+	  down for longer than approximately five seconds.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called nwbutton.
+
+	  Most people will answer Y to this question and "Reboot Using Button"
+	  below to be able to initiate a system shutdown from the button.
+
+config NWBUTTON_REBOOT
+	bool "Reboot Using Button"
+	depends on NWBUTTON
+	help
+	  If you say Y here, then you will be able to initiate a system
+	  shutdown and reboot by pressing the orange button a number of times.
+	  The number of presses to initiate the shutdown is two by default,
+	  but this can be altered by modifying the value of NUM_PRESSES_REBOOT
+	  in nwbutton.h and recompiling the driver or, if you compile the
+	  driver as a module, you can specify the number of presses at load
+	  time with "insmod button reboot_count=<something>".
+
+config NWFLASH
+	tristate "NetWinder flash support"
+	depends on ARCH_NETWINDER
+	help
+	  If you say Y here and create a character device /dev/flash with
+	  major 10 and minor 160 you can manipulate the flash ROM containing
+	  the NetWinder firmware. Be careful as accidentally overwriting the
+	  flash contents can render your computer unbootable. On no account
+	  allow random users access to this device. :-)
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called nwflash.
+
+	  If you're not sure, say N.
+
+source "drivers/char/hw_random/Kconfig"
+
+config XILINX_HWICAP
+	tristate "Xilinx HWICAP Support"
+	depends on MICROBLAZE
+	help
+	  This option enables support for Xilinx Internal Configuration
+	  Access Port (ICAP) driver.  The ICAP is used on Xilinx Virtex
+	  FPGA platforms to partially reconfigure the FPGA at runtime.
+
+	  If unsure, say N.
+
+config SONYPI
+	tristate "Sony Vaio Programmable I/O Control Device support"
+	depends on X86_32 && PCI && INPUT && HAS_IOPORT
+	depends on ACPI_EC || !ACPI
+	help
+	  This driver enables access to the Sony Programmable I/O Control
+	  Device which can be found in many (all ?) Sony Vaio laptops.
+
+	  If you have one of those laptops, read
+	  <file:Documentation/admin-guide/laptops/sonypi.rst>, and say Y or M here.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called sonypi.
+
+config SCx200_GPIO
+	tristate "NatSemi SCx200 GPIO Support"
+	depends on SCx200
+	select NSC_GPIO
+	help
+	  Give userspace access to the GPIO pins on the National
+	  Semiconductor SCx200 processors.
+
+	  If compiled as a module, it will be called scx200_gpio.
+
+config PC8736x_GPIO
+	tristate "NatSemi PC8736x GPIO Support"
+	depends on X86_32 && !UML
+	default SCx200_GPIO	# mostly N
+	select NSC_GPIO		# needed for support routines
+	help
+	  Give userspace access to the GPIO pins on the National
+	  Semiconductor PC-8736x (x=[03456]) SuperIO chip.  The chip
+	  has multiple functional units, inc several managed by
+	  hwmon/pc87360 driver.  Tested with PC-87366
+
+	  If compiled as a module, it will be called pc8736x_gpio.
+
+config NSC_GPIO
+	tristate "NatSemi Base GPIO Support"
+	depends on X86_32
+	# selected by SCx200_GPIO and PC8736x_GPIO
+	# what about 2 selectors differing: m != y
+	help
+	  Common support used (and needed) by scx200_gpio and
+	  pc8736x_gpio drivers.  If those drivers are built as
+	  modules, this one will be too, named nsc_gpio
+
+config DEVMEM
+	bool "/dev/mem virtual device support"
+	default y
+	help
+	  Say Y here if you want to support the /dev/mem device.
+	  The /dev/mem device is used to access areas of physical
+	  memory.
+	  When in doubt, say "Y".
+
+config NVRAM
+	tristate "/dev/nvram support"
+	depends on X86 || HAVE_ARCH_NVRAM_OPS
+	default M68K || PPC
+	help
+	  If you say Y here and create a character special file /dev/nvram
+	  with major number 10 and minor number 144 using mknod ("man mknod"),
+	  you get read and write access to the non-volatile memory.
+
+	  /dev/nvram may be used to view settings in NVRAM or to change them
+	  (with some utility). It could also be used to frequently
+	  save a few bits of very important data that may not be lost over
+	  power-off and for which writing to disk is too insecure. Note
+	  however that most NVRAM space in a PC belongs to the BIOS and you
+	  should NEVER idly tamper with it. See Ralf Brown's interrupt list
+	  for a guide to the use of CMOS bytes by your BIOS.
+
+	  This memory is conventionally called "NVRAM" on PowerPC machines,
+	  "CMOS RAM" on PCs, "NVRAM" on Ataris and "PRAM" on Macintoshes.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called nvram.
+
+config DEVPORT
+	bool "/dev/port character device"
+	depends on HAS_IOPORT
+	default y
+	help
+	  Say Y here if you want to support the /dev/port device. The /dev/port
+	  device is similar to /dev/mem, but for I/O ports.
+
+config HPET
+	bool "HPET - High Precision Event Timer" if X86
+	default n
+	depends on ACPI
+	help
+	  If you say Y here, you will have a miscdevice named "/dev/hpet/".  Each
+	  open selects one of the timers supported by the HPET.  The timers are
+	  non-periodic and/or periodic.
+
+config HPET_MMAP
+	bool "Allow mmap of HPET"
+	default y
+	depends on HPET
+	help
+	  If you say Y here, user applications will be able to mmap
+	  the HPET registers.
+
+config HPET_MMAP_DEFAULT
+	bool "Enable HPET MMAP access by default"
+	default y
+	depends on HPET_MMAP
+	help
+	  In some hardware implementations, the page containing HPET
+	  registers may also contain other things that shouldn't be
+	  exposed to the user.  This option selects the default (if
+	  kernel parameter hpet_mmap is not set) user access to the
+	  registers for applications that require it.
+
+config HANGCHECK_TIMER
+	tristate "Hangcheck timer"
+	depends on X86 || PPC64 || S390
+	help
+	  The hangcheck-timer module detects when the system has gone
+	  out to lunch past a certain margin.  It can reboot the system
+	  or merely print a warning.
+
+config UV_MMTIMER
+	tristate "UV_MMTIMER Memory mapped RTC for SGI UV"
+	depends on X86_UV
+	default m
+	help
+	  The uv_mmtimer device allows direct userspace access to the
+	  UV system timer.
+
+source "drivers/char/tpm/Kconfig"
+
+config TELCLOCK
+	tristate "Telecom clock driver for ATCA SBC"
+	depends on X86
+	default n
+	help
+	  The telecom clock device is specific to the MPCBL0010 and MPCBL0050
+	  ATCA computers and allows direct userspace access to the
+	  configuration of the telecom clock configuration settings.  This
+	  device is used for hardware synchronization across the ATCA backplane
+	  fabric.  Upon loading, the driver exports a sysfs directory,
+	  /sys/devices/faux/telco_clock, with a number of files for
+	  controlling the behavior of this hardware.
+
+source "drivers/s390/char/Kconfig"
+
+source "drivers/char/xillybus/Kconfig"
+
+config ADI
+	tristate "SPARC Privileged ADI driver"
+	depends on SPARC64
+	default m
+	help
+	  SPARC M7 and newer processors utilize ADI (Application Data
+	  Integrity) to version and protect memory.  This driver provides
+	  read/write access to the ADI versions for privileged processes.
+	  This feature is also known as MCD (Memory Corruption Detection)
+	  and SSM (Silicon Secured Memory).  Intended consumers of this
+	  driver include crash and makedumpfile.
+
+endmenu