arm64/boot: Disable trapping of PMZR_EL0 writes to EL2grafted

__init_el2_fgt2() writes one mask to both HDFGRTR2_EL2 and HDFGWTR2_EL2.
PMZR_EL0 is write-only, so its trap bit, nPMZR_EL0, exists only in
HDFGWTR2_EL2 and is therefore never set: a PMZR_EL0 write from the host
traps to EL2, where the nVHE hypervisor has no handler and BUG()s. The
kernel never writes PMZR_EL0, but kernel.perf_user_access=1 has the PMU
driver set PMUSERENR_EL0.UEN for a task with a user-read event, so a
write from EL0 reaches the trap and takes the host down without a panic
message.

Accumulate the HDFGWTR2_EL2 bits separately, as __init_el2_fgt() already
does for HDFGWTR_EL2, and set nPMZR_EL0 with the other FEAT_PMUv3p9
bits.

Fixes: 858c7bfcb35e1 ("arm64/boot: Enable EL2 requirements for FEAT_PMUv3p9")
Cc: stable@vger.kernel.org
Signed-off-by: Fuad Tabba <fuad.tabba@linux.dev>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Oliver Upton <oupton@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>

1 files changed, 73 insertions, 0 deletions

diff --git a/drivers/block/drbd/Kconfig b/drivers/block/drbd/Kconfig
new file mode 100644
index 000000000..495a72da0
--- /dev/null
+++ b/drivers/block/drbd/Kconfig
@@ -0,0 +1,73 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# DRBD device driver configuration
+#
+
+comment "DRBD disabled because PROC_FS or INET not selected"
+	depends on PROC_FS='n' || INET='n'
+
+config BLK_DEV_DRBD
+	tristate "DRBD Distributed Replicated Block Device support"
+	depends on PROC_FS && INET
+	select LRU_CACHE
+	select CRC32
+	help
+
+	  NOTE: In order to authenticate connections you have to select
+	  CRYPTO_HMAC and a hash function as well.
+
+	  DRBD is a shared-nothing, synchronously replicated block device. It
+	  is designed to serve as a building block for high availability
+	  clusters and in this context, is a "drop-in" replacement for shared
+	  storage. Simplistically, you could see it as a network RAID 1.
+
+	  Each minor device has a role, which can be 'primary' or 'secondary'.
+	  On the node with the primary device the application is supposed to
+	  run and to access the device (/dev/drbdX). Every write is sent to
+	  the local 'lower level block device' and, across the network, to the
+	  node with the device in 'secondary' state.  The secondary device
+	  simply writes the data to its lower level block device.
+
+	  DRBD can also be used in dual-Primary mode (device writable on both
+	  nodes), which means it can exhibit shared disk semantics in a
+	  shared-nothing cluster.  Needless to say, on top of dual-Primary
+	  DRBD utilizing a cluster file system is necessary to maintain for
+	  cache coherency.
+
+	  For automatic failover you need a cluster manager (e.g. heartbeat).
+	  See also: https://www.drbd.org/, http://www.linux-ha.org
+
+	  If unsure, say N.
+
+config DRBD_FAULT_INJECTION
+	bool "DRBD fault injection"
+	depends on BLK_DEV_DRBD
+	help
+
+	  Say Y here if you want to simulate IO errors, in order to test DRBD's
+	  behavior.
+
+	  The actual simulation of IO errors is done by writing 3 values to
+	  /sys/module/drbd/parameters/
+
+	  enable_faults: bitmask of...
+	  1	meta data write
+	  2               read
+	  4	resync data write
+	  8	            read
+	  16	data write
+	  32	data read
+	  64	read ahead
+	  128	kmalloc of bitmap
+	  256	allocation of peer_requests
+	  512	insert data corruption on receiving side
+
+	  fault_devs: bitmask of minor numbers
+	  fault_rate: frequency in percent
+
+	  Example: Simulate data write errors on /dev/drbd0 with a probability of 5%.
+		echo 16 > /sys/module/drbd/parameters/enable_faults
+		echo 1 > /sys/module/drbd/parameters/fault_devs
+		echo 5 > /sys/module/drbd/parameters/fault_rate
+
+	  If unsure, say N.