Merge tag 'i3c/for-7.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linuxgrafted

Pull I3C updates from Alexandre Belloni:
 "A new driver this cycle, for the AMD AXI I3C controller.

  There are also new features such as IBI wakeup support, SETAASA device
  discovery and ACPI support for the the DAA methods, meaning we can now
  communicate with the SPD devices on DDR5 modules.

  New driver:
   - AMD AXI I3C master controller

  Subsystem:
   - I3C Common Command Code (CCC) handling improvements, especially
     around GET CCCs
   - SETAASA device discovery support
   - ACPI support for all existing DAA methods like SETDASA, SETNEWDA as
     well as I2C devices on I3C bus
   - IBI-based wakeup support

  Drivers:
   - dw: SETAASA support
   - mipi-i3c-hci: advertise IBI wakeup capability, AMD_PT I3C
     controller support, PIO queue management support for HCI v1.2
   - renesas: improve suspend to RAM support, add runtime PM support"

* tag 'i3c/for-7.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux: (70 commits)
  i3c: dw: reduce do_daa time if there's no client
  i3c: mipi-i3c-hci: Add support for AMD_PT I3C controller
  i3c: mipi-i3c-hci: Add PIO queue management support for HCI v1.2
  i3c: mipi-i3c-hci: Fix missing STAT_IBI_STATUS_THLD in PIO mode
  i3c: dw: rename "pclk" to "apb" to match dt-binding
  i3c: dw: make struct dw_i3c_cmd smaller
  i3c: dw: use COMMAND_PORT_TRANSFER_ARG instead of hardcoding
  i3c: renesas: Don't register devices when ENTDAA times out
  i3c: master: dw-i3c-master: fix OD timing for first broadcast
  i3c: mipi-i3c-hci: Advertise IBI wakeup capability
  i3c: mipi-i3c-hci: Factor out i3c_hci_sysdev()
  i3c: mipi-i3c-hci-pci: Propagate I3C wakeup requirements to PCI
  i3c: master: Reject IBI requests from non-IBI-capable devices
  i3c: master: Add helper to query bus wakeup requirements
  i3c: master: Report wakeup events for IBIs
  i3c: master: Support IBI-based wakeup capability
  i3c: master: Fix potential UAF in i3c_device_match()
  i3c: master: Fix potential UAF in i3c_device_uevent()
  i3c: Make dev->desc locking assumptions explicit
  i3c: master: Fix use-after-free of master->this
  ...

1 files changed, 88 insertions, 0 deletions

diff --git a/Documentation/networking/vxlan.rst b/Documentation/networking/vxlan.rst
new file mode 100644
index 000000000..2759dc1cc
--- /dev/null
+++ b/Documentation/networking/vxlan.rst
@@ -0,0 +1,88 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+======================================================
+Virtual eXtensible Local Area Networking documentation
+======================================================
+
+The VXLAN protocol is a tunnelling protocol designed to solve the
+problem of limited VLAN IDs (4096) in IEEE 802.1q.  With VXLAN the
+size of the identifier is expanded to 24 bits (16777216).
+
+VXLAN is described by IETF RFC 7348, and has been implemented by a
+number of vendors.  The protocol runs over UDP using a single
+destination port.  This document describes the Linux kernel tunnel
+device, there is also a separate implementation of VXLAN for
+Openvswitch.
+
+Unlike most tunnels, a VXLAN is a 1 to N network, not just point to
+point. A VXLAN device can learn the IP address of the other endpoint
+either dynamically in a manner similar to a learning bridge, or make
+use of statically-configured forwarding entries.
+
+The management of vxlan is done in a manner similar to its two closest
+neighbors GRE and VLAN. Configuring VXLAN requires the version of
+iproute2 that matches the kernel release where VXLAN was first merged
+upstream.
+
+1. Create vxlan device::
+
+    # ip link add vxlan0 type vxlan id 42 group 239.1.1.1 dev eth1 dstport 4789
+
+This creates a new device named vxlan0.  The device uses the multicast
+group 239.1.1.1 over eth1 to handle traffic for which there is no
+entry in the forwarding table.  The destination port number is set to
+the IANA-assigned value of 4789.  The Linux implementation of VXLAN
+pre-dates the IANA's selection of a standard destination port number
+and uses the Linux-selected value by default to maintain backwards
+compatibility.
+
+2. Delete vxlan device::
+
+    # ip link delete vxlan0
+
+3. Show vxlan info::
+
+    # ip -d link show vxlan0
+
+It is possible to create, destroy and display the vxlan
+forwarding table using the new bridge command.
+
+1. Create forwarding table entry::
+
+    # bridge fdb add to 00:17:42:8a:b4:05 dst 192.19.0.2 dev vxlan0
+
+2. Delete forwarding table entry::
+
+    # bridge fdb delete 00:17:42:8a:b4:05 dev vxlan0
+
+3. Show forwarding table::
+
+    # bridge fdb show dev vxlan0
+
+The following NIC features may indicate support for UDP tunnel-related
+offloads (most commonly VXLAN features, but support for a particular
+encapsulation protocol is NIC specific):
+
+ - `tx-udp_tnl-segmentation`
+ - `tx-udp_tnl-csum-segmentation`
+    ability to perform TCP segmentation offload of UDP encapsulated frames
+
+ - `rx-udp_tunnel-port-offload`
+    receive side parsing of UDP encapsulated frames which allows NICs to
+    perform protocol-aware offloads, like checksum validation offload of
+    inner frames (only needed by NICs without protocol-agnostic offloads)
+
+For devices supporting `rx-udp_tunnel-port-offload` the list of currently
+offloaded ports can be interrogated with `ethtool`::
+
+  $ ethtool --show-tunnels eth0
+  Tunnel information for eth0:
+    UDP port table 0:
+      Size: 4
+      Types: vxlan
+      No entries
+    UDP port table 1:
+      Size: 4
+      Types: geneve, vxlan-gpe
+      Entries (1):
+          port 1230, vxlan-gpe