KVM: Don't pre-reserve xarray entries when storing empty/NULL attributesgrafted

Skip the xarray reservation loop when clearing all memory attributes, as
storing NULL only erases the entry and never needs to allocate, so no
reservation (and no cleanup of a failed one) is required in that case.

Suggested-by: Sean Christopherson <seanjc@google.com>
Cc: David Ballesteros <davimaba.v@proton.me>
Signed-off-by: Zeng Chi <zengchi@kylinos.cn>
Link: https://patch.msgid.link/20260921102442.1232375-1-zeng_chi911@163.com
[sean: split to separate patch]
Signed-off-by: Sean Christopherson <seanjc@google.com>

1 files changed, 88 insertions, 0 deletions

diff --git a/Documentation/networking/vxlan.rst b/Documentation/networking/vxlan.rst
new file mode 100644
index 000000000..2759dc1cc
--- /dev/null
+++ b/Documentation/networking/vxlan.rst
@@ -0,0 +1,88 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+======================================================
+Virtual eXtensible Local Area Networking documentation
+======================================================
+
+The VXLAN protocol is a tunnelling protocol designed to solve the
+problem of limited VLAN IDs (4096) in IEEE 802.1q.  With VXLAN the
+size of the identifier is expanded to 24 bits (16777216).
+
+VXLAN is described by IETF RFC 7348, and has been implemented by a
+number of vendors.  The protocol runs over UDP using a single
+destination port.  This document describes the Linux kernel tunnel
+device, there is also a separate implementation of VXLAN for
+Openvswitch.
+
+Unlike most tunnels, a VXLAN is a 1 to N network, not just point to
+point. A VXLAN device can learn the IP address of the other endpoint
+either dynamically in a manner similar to a learning bridge, or make
+use of statically-configured forwarding entries.
+
+The management of vxlan is done in a manner similar to its two closest
+neighbors GRE and VLAN. Configuring VXLAN requires the version of
+iproute2 that matches the kernel release where VXLAN was first merged
+upstream.
+
+1. Create vxlan device::
+
+    # ip link add vxlan0 type vxlan id 42 group 239.1.1.1 dev eth1 dstport 4789
+
+This creates a new device named vxlan0.  The device uses the multicast
+group 239.1.1.1 over eth1 to handle traffic for which there is no
+entry in the forwarding table.  The destination port number is set to
+the IANA-assigned value of 4789.  The Linux implementation of VXLAN
+pre-dates the IANA's selection of a standard destination port number
+and uses the Linux-selected value by default to maintain backwards
+compatibility.
+
+2. Delete vxlan device::
+
+    # ip link delete vxlan0
+
+3. Show vxlan info::
+
+    # ip -d link show vxlan0
+
+It is possible to create, destroy and display the vxlan
+forwarding table using the new bridge command.
+
+1. Create forwarding table entry::
+
+    # bridge fdb add to 00:17:42:8a:b4:05 dst 192.19.0.2 dev vxlan0
+
+2. Delete forwarding table entry::
+
+    # bridge fdb delete 00:17:42:8a:b4:05 dev vxlan0
+
+3. Show forwarding table::
+
+    # bridge fdb show dev vxlan0
+
+The following NIC features may indicate support for UDP tunnel-related
+offloads (most commonly VXLAN features, but support for a particular
+encapsulation protocol is NIC specific):
+
+ - `tx-udp_tnl-segmentation`
+ - `tx-udp_tnl-csum-segmentation`
+    ability to perform TCP segmentation offload of UDP encapsulated frames
+
+ - `rx-udp_tunnel-port-offload`
+    receive side parsing of UDP encapsulated frames which allows NICs to
+    perform protocol-aware offloads, like checksum validation offload of
+    inner frames (only needed by NICs without protocol-agnostic offloads)
+
+For devices supporting `rx-udp_tunnel-port-offload` the list of currently
+offloaded ports can be interrogated with `ethtool`::
+
+  $ ethtool --show-tunnels eth0
+  Tunnel information for eth0:
+    UDP port table 0:
+      Size: 4
+      Types: vxlan
+      No entries
+    UDP port table 1:
+      Size: 4
+      Types: geneve, vxlan-gpe
+      Entries (1):
+          port 1230, vxlan-gpe