selftests/bpf: Reject graph kptr use after RCU unlockgrafted

Add a sleepable verifier test that loads a graph-node local kptr in an
explicit RCU read-side critical section, then passes its node to
bpf_rbtree_remove() after the section ends.

Before the verifier fix, the stale NON_OWN_REF flag makes the node look like
a live borrowed reference and the program is accepted. After the fix, the
pointer is demoted without NON_OWN_REF and the graph kfunc argument is
rejected.

Also exercise a graph kptr loaded while a spin lock provides implicit RCU
protection. The pointer must be invalidated when the lock is released, which
guards the required ordering between non-owning-reference invalidation and
RCU demotion.

Update the existing fault-protected load test state description. The
post-unlock pointer no longer carries NON_OWN_REF, but remains readable
because the load is rewritten to use BPF_PROBE_MEM.

Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20260904084325.52250-7-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

1 files changed, 78 insertions, 0 deletions

diff --git a/Documentation/networking/ipv6.rst b/Documentation/networking/ipv6.rst
new file mode 100644
index 000000000..ba09c2f2d
--- /dev/null
+++ b/Documentation/networking/ipv6.rst
@@ -0,0 +1,78 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+====
+IPv6
+====
+
+
+Options for the ipv6 module are supplied as parameters at load time.
+
+Module options may be given as command line arguments to the insmod
+or modprobe command, but are usually specified in either
+``/etc/modules.d/*.conf`` configuration files, or in a distro-specific
+configuration file.
+
+The available ipv6 module parameters are listed below.  If a parameter
+is not specified the default value is used.
+
+The parameters are as follows:
+
+disable
+
+	Specifies whether to load the IPv6 module, but disable all
+	its functionality.  This might be used when another module
+	has a dependency on the IPv6 module being loaded, but no
+	IPv6 addresses or operations are desired.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 is enabled.
+
+		This is the default value.
+
+	1
+		IPv6 is disabled.
+
+		No IPv6 addresses will be added to interfaces, and
+		it will not be possible to open an IPv6 socket.
+
+		A reboot is required to enable IPv6.
+
+autoconf
+
+	Specifies whether to enable IPv6 address autoconfiguration
+	on all interfaces.  This might be used when one does not wish
+	for addresses to be automatically generated from prefixes
+	received in Router Advertisements.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 address autoconfiguration is disabled on all interfaces.
+
+		Only the IPv6 loopback address (::1) and link-local addresses
+		will be added to interfaces.
+
+	1
+		IPv6 address autoconfiguration is enabled on all interfaces.
+
+		This is the default value.
+
+disable_ipv6
+
+	Specifies whether to disable IPv6 on all interfaces.
+	This might be used when no IPv6 addresses are desired.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 is enabled on all interfaces.
+
+		This is the default value.
+
+	1
+		IPv6 is disabled on all interfaces.
+
+		No IPv6 addresses will be added to interfaces.
+