ftrace: Synchronize the initialization of ftrace_opsgrafted

There's some internal state that ftrace_ops needs to have set, but since
it can be declared outside of the ftrace.c code, it calls
ftrace_ops_init() on the ops in every global function. The issue is that
if two tasks call it on the same ops at the same time it is possible to
have the initialization of one corrupt the initialization of the other
call.

Create a ops_mutex to use to synchronize every initialization of the
ftrace_ops. The mutex is taken within checking the ftrace_ops flag that
states it was initializied but the flag is checked again after the mutex
has been taken. Checking first outside the mutex allows it to shortcut
having to take the mutex. But then the check needs to be done again after
the mute is taken in case of races.

Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260902095501.6b59af20@gandalf.local.home
Fixes: f04f24fb7e48d ("ftrace, kprobes: Fix a deadlock on ftrace_regex_lock")
Reported-by: sashiko-bot@kernel.org
Close: https://lore.kernel.org/all/20260829025528.49A831F000E9@smtp.kernel.org/
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

1 files changed, 78 insertions, 0 deletions

diff --git a/Documentation/networking/ipv6.rst b/Documentation/networking/ipv6.rst
new file mode 100644
index 000000000..ba09c2f2d
--- /dev/null
+++ b/Documentation/networking/ipv6.rst
@@ -0,0 +1,78 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+====
+IPv6
+====
+
+
+Options for the ipv6 module are supplied as parameters at load time.
+
+Module options may be given as command line arguments to the insmod
+or modprobe command, but are usually specified in either
+``/etc/modules.d/*.conf`` configuration files, or in a distro-specific
+configuration file.
+
+The available ipv6 module parameters are listed below.  If a parameter
+is not specified the default value is used.
+
+The parameters are as follows:
+
+disable
+
+	Specifies whether to load the IPv6 module, but disable all
+	its functionality.  This might be used when another module
+	has a dependency on the IPv6 module being loaded, but no
+	IPv6 addresses or operations are desired.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 is enabled.
+
+		This is the default value.
+
+	1
+		IPv6 is disabled.
+
+		No IPv6 addresses will be added to interfaces, and
+		it will not be possible to open an IPv6 socket.
+
+		A reboot is required to enable IPv6.
+
+autoconf
+
+	Specifies whether to enable IPv6 address autoconfiguration
+	on all interfaces.  This might be used when one does not wish
+	for addresses to be automatically generated from prefixes
+	received in Router Advertisements.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 address autoconfiguration is disabled on all interfaces.
+
+		Only the IPv6 loopback address (::1) and link-local addresses
+		will be added to interfaces.
+
+	1
+		IPv6 address autoconfiguration is enabled on all interfaces.
+
+		This is the default value.
+
+disable_ipv6
+
+	Specifies whether to disable IPv6 on all interfaces.
+	This might be used when no IPv6 addresses are desired.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 is enabled on all interfaces.
+
+		This is the default value.
+
+	1
+		IPv6 is disabled on all interfaces.
+
+		No IPv6 addresses will be added to interfaces.
+