sched/cache: Keep nr_pref_llc_running in the runnable domain, to fix LLC mis-scheduling buggrafted

alb_break_llc() decides whether to break LLC preference during active
load balance. It does so by testing that every runnable fair task on the
source rq prefers its LLC:

	env->src_rq->nr_pref_llc_running == env->src_rq->cfs.h_nr_runnable

But the two counters cover different sets. nr_pref_llc_running is updated
in account_llc_enqueue()/account_llc_dequeue(), next to cfs_rq->nr_queued,
so it follows queued tasks. h_nr_runnable is updated in set_delayed()/
clear_delayed() and drops delay-dequeued tasks.

So under DELAY_DEQUEUE, a preferring task that goes to sleep stays counted
in nr_pref_llc_running while h_nr_runnable falls. The equality then breaks,
alb_break_llc() returns false, and active balance is free to pull a task
off its preferred LLC. Active balance only moves runnable tasks, and this
is the only LLC check it consults: once the stopper runs, LBF_ACTIVE_LB
skips the per-task test in can_migrate_task(). The runnable set is the one
we want.

Fix it on the counter side. A task should be counted in
nr_pref_llc_running exactly while it is both queued on its preferred LLC
(pref_llc_queued) and runnable (!sched_delayed). Define that membership
once in task_pref_llc_runnable(), and adjust the counter only through
pref_llc_running_inc()/pref_llc_running_dec() from the four sites that
change either input: account_llc_enqueue(), account_llc_dequeue(),
set_delayed() and clear_delayed(). Gating every update on the same
predicate keeps the delay, wake and dequeue paths from double-counting
or underflowing; see the comments at those sites for the ordering.

nr_llc_running and sd->llc_counts are not touched and stay on queued
semantics.

Fixes: 714059f79ff0 ("sched/cache: Handle moving single tasks to/from their preferred LLC")
Closes: https://lore.kernel.org/lkml/20260827135000.735138-1-zhanxusheng@xiaomi.com/
Reported-by: Zhan Xusheng <zhanxusheng@xiaomi.com>
Suggested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kayra Cizmeci <kayracizmeci@gmail.com>
Cc: <stable@kernel.org> # v7.2.x
Link: https://patch.msgid.link/06af61afedac32e6477f57feb4d658f6c411c3af.1790035273.git.tim.c.chen@linux.intel.com

1 files changed, 78 insertions, 0 deletions

diff --git a/Documentation/networking/ipv6.rst b/Documentation/networking/ipv6.rst
new file mode 100644
index 000000000..ba09c2f2d
--- /dev/null
+++ b/Documentation/networking/ipv6.rst
@@ -0,0 +1,78 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+====
+IPv6
+====
+
+
+Options for the ipv6 module are supplied as parameters at load time.
+
+Module options may be given as command line arguments to the insmod
+or modprobe command, but are usually specified in either
+``/etc/modules.d/*.conf`` configuration files, or in a distro-specific
+configuration file.
+
+The available ipv6 module parameters are listed below.  If a parameter
+is not specified the default value is used.
+
+The parameters are as follows:
+
+disable
+
+	Specifies whether to load the IPv6 module, but disable all
+	its functionality.  This might be used when another module
+	has a dependency on the IPv6 module being loaded, but no
+	IPv6 addresses or operations are desired.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 is enabled.
+
+		This is the default value.
+
+	1
+		IPv6 is disabled.
+
+		No IPv6 addresses will be added to interfaces, and
+		it will not be possible to open an IPv6 socket.
+
+		A reboot is required to enable IPv6.
+
+autoconf
+
+	Specifies whether to enable IPv6 address autoconfiguration
+	on all interfaces.  This might be used when one does not wish
+	for addresses to be automatically generated from prefixes
+	received in Router Advertisements.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 address autoconfiguration is disabled on all interfaces.
+
+		Only the IPv6 loopback address (::1) and link-local addresses
+		will be added to interfaces.
+
+	1
+		IPv6 address autoconfiguration is enabled on all interfaces.
+
+		This is the default value.
+
+disable_ipv6
+
+	Specifies whether to disable IPv6 on all interfaces.
+	This might be used when no IPv6 addresses are desired.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 is enabled on all interfaces.
+
+		This is the default value.
+
+	1
+		IPv6 is disabled on all interfaces.
+
+		No IPv6 addresses will be added to interfaces.
+