ftrace: Synchronize the initialization of ftrace_opsgrafted

There's some internal state that ftrace_ops needs to have set, but since
it can be declared outside of the ftrace.c code, it calls
ftrace_ops_init() on the ops in every global function. The issue is that
if two tasks call it on the same ops at the same time it is possible to
have the initialization of one corrupt the initialization of the other
call.

Create a ops_mutex to use to synchronize every initialization of the
ftrace_ops. The mutex is taken within checking the ftrace_ops flag that
states it was initializied but the flag is checked again after the mutex
has been taken. Checking first outside the mutex allows it to shortcut
having to take the mutex. But then the check needs to be done again after
the mute is taken in case of races.

Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260902095501.6b59af20@gandalf.local.home
Fixes: f04f24fb7e48d ("ftrace, kprobes: Fix a deadlock on ftrace_regex_lock")
Reported-by: sashiko-bot@kernel.org
Close: https://lore.kernel.org/all/20260829025528.49A831F000E9@smtp.kernel.org/
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

1 files changed, 59 insertions, 0 deletions

diff --git a/Documentation/networking/bareudp.rst b/Documentation/networking/bareudp.rst
new file mode 100644
index 000000000..621cb9575
--- /dev/null
+++ b/Documentation/networking/bareudp.rst
@@ -0,0 +1,59 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+========================================
+Bare UDP Tunnelling Module Documentation
+========================================
+
+There are various L3 encapsulation standards using UDP being discussed to
+leverage the UDP based load balancing capability of different networks.
+MPLSoUDP (https://tools.ietf.org/html/rfc7510) is one among them.
+
+The Bareudp tunnel module provides a generic L3 encapsulation support for
+tunnelling different L3 protocols like MPLS, IP, NSH etc. inside a UDP tunnel.
+
+Special Handling
+----------------
+
+The bareudp device supports special handling for MPLS & IP as they can have
+multiple ethertypes.
+The MPLS protocol can have ethertypes ETH_P_MPLS_UC (unicast) & ETH_P_MPLS_MC (multicast).
+IP protocol can have ethertypes ETH_P_IP (v4) & ETH_P_IPV6 (v6).
+This special handling can be enabled only for ethertypes ETH_P_IP & ETH_P_MPLS_UC
+with a flag called multiproto mode.
+
+Usage
+------
+
+1) Device creation & deletion
+
+    a) ip link add dev bareudp0 type bareudp dstport 6635 ethertype mpls_uc
+
+       This creates a bareudp tunnel device which tunnels L3 traffic with ethertype
+       0x8847 (MPLS traffic). The destination port of the UDP header will be set to
+       6635.The device will listen on UDP port 6635 to receive traffic.
+
+    b) ip link delete bareudp0
+
+2) Device creation with multiproto mode enabled
+
+The multiproto mode allows bareudp tunnels to handle several protocols of the
+same family. It is currently only available for IP and MPLS. This mode has to
+be enabled explicitly with the "multiproto" flag.
+
+    a) ip link add dev bareudp0 type bareudp dstport 6635 ethertype ipv4 multiproto
+
+       For an IPv4 tunnel the multiproto mode allows the tunnel to also handle
+       IPv6.
+
+    b) ip link add dev bareudp0 type bareudp dstport 6635 ethertype mpls_uc multiproto
+
+       For MPLS, the multiproto mode allows the tunnel to handle both unicast
+       and multicast MPLS packets.
+
+3) Device Usage
+
+The bareudp device could be used along with OVS or flower filter in TC.
+The OVS or TC flower layer must set the tunnel information in the SKB dst field before
+sending the packet buffer to the bareudp device for transmission. On reception, the
+bareUDP device extracts and stores the tunnel information in the SKB dst field before
+passing the packet buffer to the network stack.