drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validationgrafted

amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and
uses the first encoding that validates. YCbCr 4:4:4 is listed before
RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the
"color format" property is left at AUTO, even though RGB fits the same
link.

That contradicts the documented AUTO behaviour for HDMI in enum
drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when
the bandwidth is not available or the mode is 4:2:0-only), which the
amdgpu implementation of the property also describes. It also leaves
the "Broadcast RGB" property without effect on such sinks, since the
quantization range it selects only applies to RGB output.

Try RGB first. The mask still holds every encoding the sink supports,
so a mode that cannot carry RGB falls back exactly as before.

For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced
through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI
sink that advertised it.

Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation")
Suggested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Assisted-by: Claude Code:claude-fable-5-1
Signed-off-by: Adrian Betschart <adrian.betschart@cinemaone.ch>
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7)

1 files changed, 49 insertions, 0 deletions

diff --git a/Documentation/networking/alias.rst b/Documentation/networking/alias.rst
new file mode 100644
index 000000000..af7c5ee92
--- /dev/null
+++ b/Documentation/networking/alias.rst
@@ -0,0 +1,49 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===========
+IP-Aliasing
+===========
+
+IP-aliases are an obsolete way to manage multiple IP-addresses/masks
+per interface. Newer tools such as iproute2 support multiple
+address/prefixes per interface, but aliases are still supported
+for backwards compatibility.
+
+An alias is formed by adding a colon and a string when running ifconfig.
+This string is usually numeric, but this is not a must.
+
+
+Alias creation
+==============
+
+Alias creation is done by 'magic' interface naming: eg. to create a
+200.1.1.1 alias for eth0 ...
+::
+
+  # ifconfig eth0:0 200.1.1.1  etc,etc....
+	~~ -> request alias #0 creation (if not yet exists) for eth0
+
+The corresponding route is also set up by this command.  Please note:
+The route always points to the base interface.
+
+
+Alias deletion
+==============
+
+The alias is removed by shutting the alias down::
+
+  # ifconfig eth0:0 down
+	~~~~~~~~~~ -> will delete alias
+
+
+Alias (re-)configuring
+======================
+
+Aliases are not real devices, but programs should be able to configure
+and refer to them as usual (ifconfig, route, etc).
+
+
+Relationship with main device
+=============================
+
+If the base device is shut down the added aliases will be deleted too.