iio: proximity: vl53l0x-i2c: claim direct mode for raw readsgrafted

vl53l0x_read_raw() starts a single-shot ranging measurement and reads
back the result. Once the triggered buffer is enabled the sensor runs in
continuous mode and its data-ready interrupt is routed to the trigger,
so a concurrent in_distance_raw read disturbs the streaming setup and
never gets its completion, returning -ETIMEDOUT.

The original submission claimed direct mode here, but it was dropped
during review because the driver had no buffer support at the time [1].
Continuous (buffered) mode was later added without restoring the
claim [2], reintroducing the conflict.

Reject direct reads while buffered capture is active by claiming direct
mode around the measurement, as the vl53l1x sibling already does.

Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support")
Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1]
Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2]
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

1 files changed, 55 insertions, 0 deletions

diff --git a/Documentation/i2c/old-module-parameters.rst b/Documentation/i2c/old-module-parameters.rst
new file mode 100644
index 000000000..b08b6daab
--- /dev/null
+++ b/Documentation/i2c/old-module-parameters.rst
@@ -0,0 +1,55 @@
+================================================================
+I2C device driver binding control from user-space in old kernels
+================================================================
+
+.. NOTE::
+   Note: this section is only relevant if you are handling some old code
+   found in kernel 2.6. If you work with more recent kernels, you can
+   safely skip this section.
+
+Up to kernel 2.6.32, many I2C drivers used helper macros provided by
+<linux/i2c.h> which created standard module parameters to let the user
+control how the driver would probe I2C buses and attach to devices. These
+parameters were known as ``probe`` (to let the driver probe for an extra
+address), ``force`` (to forcibly attach the driver to a given device) and
+``ignore`` (to prevent a driver from probing a given address).
+
+With the conversion of the I2C subsystem to the standard device driver
+binding model, it became clear that these per-module parameters were no
+longer needed, and that a centralized implementation was possible. The new,
+sysfs-based interface is described in
+Documentation/i2c/instantiating-devices.rst, section
+"Method 4: Instantiate from user-space".
+
+Below is a mapping from the old module parameters to the new interface.
+
+Attaching a driver to an I2C device
+-----------------------------------
+
+Old method (module parameters)::
+
+  # modprobe <driver> probe=1,0x2d
+  # modprobe <driver> force=1,0x2d
+  # modprobe <driver> force_<device>=1,0x2d
+
+New method (sysfs interface)::
+
+  # echo <device> 0x2d > /sys/bus/i2c/devices/i2c-1/new_device
+
+Preventing a driver from attaching to an I2C device
+---------------------------------------------------
+
+Old method (module parameters)::
+
+  # modprobe <driver> ignore=1,0x2f
+
+New method (sysfs interface)::
+
+  # echo dummy 0x2f > /sys/bus/i2c/devices/i2c-1/new_device
+  # modprobe <driver>
+
+Of course, it is important to instantiate the ``dummy`` device before loading
+the driver. The dummy device will be handled by i2c-core itself, preventing
+other drivers from binding to it later on. If there is a real device at the
+problematic address, and you want another driver to bind to it, then simply
+pass the name of the device in question instead of ``dummy``.