Merge tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlgrafted

Pull pin control updates from Linus Walleij:
 "Core changes:

   - Use the non-blocking mux_state_try_select() in the generic MUX pin
     control back-end

   - Free pin maps on pinctrl_generic_to_map() failure in the core
     helpers

  New hardware pin control:

   - Qualcomm Maili TLMM SoC, PMG1110 PMIC, and Eliza LPASS LPI TLMM SoC
     (this is for the low power audio, LPASS = Low Power Audio SubSystem
     portions)

   - Upboard support on top of the Intel pin controller

   - Apple T6030 and T6031 support (just compatible strings)

   - Samsung Exynos 8855 SoC

   - Mediatek MT6858 SoC

   - Rockchip RK3308B and RV1106 SoCs

   - Airoha EN7523 and AN7563 SoCs

  Improvements:

   - Qualcomm TLMM GPIOs are unconditionally marked as wakeup capable

   - Qualcomm improvements on top of the Qualcomm PDC (power domain
     controller) irqchip improvements from tglx:s tree

   - Qualcomm IPQ806x and IPQ9650 non-urgent pin grop fixups

   - The NPCM8xx driver has been put into shape fixing many pin and
     group definitions

   - Some non-urgent Tegra 264 pin assignments are fixed up

   - Some non-urgent fixups to Airoha AN7581 and AN7583 registers and
     pin assignments, missing features etc"

* tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (130 commits)
  dt-bindings: pinctrl: Convert TI DA850 pupd to DT schema
  pinctrl: meson: sync some modify from A4
  pinctrl: meson: a4: Add input enable pin configuration
  pinctrl: realtek: rtd1625: remove unused group name spdif_sel
  pinctrl: realtek: rtd1625: fix base_bit for VE4 GPIO 13
  dt-bindings: pinctrl: microchip,pic32mzda-pinctrl: Convert to DT schema
  Revert "Merge branch 'ib-rsk7204' into devel"
  pinctrl: rockchip: Add RV1106 pinctrl support
  dt-bindings: pinctrl: rockchip: Add RV1106 compatible
  pinctrl: rockchip: Decode drive strength in the get function
  pinctrl: fix PINCTRL_GENERIC_MUX not always being selectable
  pinctrl: airoha: add support of an7563 SoC
  dt-bindings: pinctrl: airoha: add support of an7563 pin controller
  pinctrl: airoha: try to find chip scu node by phandle first
  pinctrl: airoha: add support of en7523 SoC
  dt-bindings: pinctrl: airoha: add support of en7523 pin controller
  pinctrl: airoha: an7583: add support for olt pinmux
  pinctrl: airoha: an7583: add support for pon_alt pinmux
  pinctrl: airoha: an7583: add support for npu_uart pinmux
  dt-bindings: pinctrl: airoha: an7583: add missed features
  ...

1 files changed, 105 insertions, 0 deletions

diff --git a/Documentation/gpu/amdgpu/debugging.rst b/Documentation/gpu/amdgpu/debugging.rst
new file mode 100644
index 000000000..ac914d524
--- /dev/null
+++ b/Documentation/gpu/amdgpu/debugging.rst
@@ -0,0 +1,105 @@
+===============
+ GPU Debugging
+===============
+
+General Debugging Options
+=========================
+
+The DebugFS section provides documentation on a number files to aid in debugging
+issues on the GPU.
+
+
+GPUVM Debugging
+===============
+
+To aid in debugging GPU virtual memory related problems, the driver supports a
+number of options module parameters:
+
+`vm_fault_stop` - If non-0, halt the GPU memory controller on a GPU page fault.
+
+`vm_update_mode` - If non-0, use the CPU to update GPU page tables rather than
+the GPU.
+
+
+Decoding a GPUVM Page Fault
+===========================
+
+If you see a GPU page fault in the kernel log, you can decode it to figure
+out what is going wrong in your application.  A page fault in your kernel
+log may look something like this:
+
+::
+
+ [gfxhub0] no-retry page fault (src_id:0 ring:24 vmid:3 pasid:32777, for process glxinfo pid 2424 thread glxinfo:cs0 pid 2425)
+   in page starting at address 0x0000800102800000 from IH client 0x1b (UTCL2)
+ VM_L2_PROTECTION_FAULT_STATUS:0x00301030
+ 	Faulty UTCL2 client ID: TCP (0x8)
+ 	MORE_FAULTS: 0x0
+ 	WALKER_ERROR: 0x0
+ 	PERMISSION_FAULTS: 0x3
+ 	MAPPING_ERROR: 0x0
+ 	RW: 0x0
+
+First you have the memory hub, gfxhub and mmhub.  gfxhub is the memory
+hub used for graphics, compute, and sdma on some chips.  mmhub is the
+memory hub used for multi-media and sdma on some chips.
+
+Next you have the vmid and pasid.  If the vmid is 0, this fault was likely
+caused by the kernel driver or firmware.  If the vmid is non-0, it is generally
+a fault in a user application.  The pasid is used to link a vmid to a system
+process id.  If the process is active when the fault happens, the process
+information will be printed.
+
+The GPU virtual address that caused the fault comes next.
+
+The client ID indicates the GPU block that caused the fault.
+Some common client IDs:
+
+- CB/DB: The color/depth backend of the graphics pipe
+- CPF: Command Processor Frontend
+- CPC: Command Processor Compute
+- CPG: Command Processor Graphics
+- TCP/SQC/SQG: Shaders
+- SDMA: SDMA engines
+- VCN: Video encode/decode engines
+- JPEG: JPEG engines
+
+PERMISSION_FAULTS describe what faults were encountered:
+
+- bit 0: the PTE was not valid
+- bit 1: the PTE read bit was not set
+- bit 2: the PTE write bit was not set
+- bit 3: the PTE execute bit was not set
+
+Finally, RW, indicates whether the access was a read (0) or a write (1).
+
+In the example above, a shader (cliend id = TCP) generated a read (RW = 0x0) to
+an invalid page (PERMISSION_FAULTS = 0x3) at GPU virtual address
+0x0000800102800000.  The user can then inspect their shader code and resource
+descriptor state to determine what caused the GPU page fault.
+
+UMR
+===
+
+`umr <https://gitlab.freedesktop.org/tomstdenis/umr>`_ is a general purpose
+GPU debugging and diagnostics tool.  Please see the umr
+`documentation <https://umr.readthedocs.io/en/main/>`_ for more information
+about its capabilities.
+
+Debugging backlight brightness
+==============================
+Default backlight brightness is intended to be set via the policy advertised
+by the firmware.  Firmware will often provide different defaults for AC or DC.
+Furthermore, some userspace software will save backlight brightness during
+the previous boot and attempt to restore it.
+
+Some firmware also has support for a feature called "Custom Backlight Curves"
+where an input value for brightness is mapped along a linearly interpolated
+curve of brightness values that better match display characteristics.
+
+In the event of problems happening with backlight, there is a trace event
+that can be enabled at bootup to log every brightness change request.
+This can help isolate where the problem is. To enable the trace event add
+the following to the kernel command line:
+
+  tp_printk trace_event=amdgpu_dm:amdgpu_dm_brightness:mod:amdgpu trace_buf_size=1M