iio: proximity: vl53l0x-i2c: claim direct mode for raw readsgrafted

vl53l0x_read_raw() starts a single-shot ranging measurement and reads
back the result. Once the triggered buffer is enabled the sensor runs in
continuous mode and its data-ready interrupt is routed to the trigger,
so a concurrent in_distance_raw read disturbs the streaming setup and
never gets its completion, returning -ETIMEDOUT.

The original submission claimed direct mode here, but it was dropped
during review because the driver had no buffer support at the time [1].
Continuous (buffered) mode was later added without restoring the
claim [2], reintroducing the conflict.

Reject direct reads while buffered capture is active by claiming direct
mode around the measurement, as the vl53l1x sibling already does.

Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support")
Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1]
Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2]
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

1 files changed, 75 insertions, 0 deletions

diff --git a/Documentation/firmware-guide/acpi/aml-debugger.rst b/Documentation/firmware-guide/acpi/aml-debugger.rst
new file mode 100644
index 000000000..a889d43bc
--- /dev/null
+++ b/Documentation/firmware-guide/acpi/aml-debugger.rst
@@ -0,0 +1,75 @@
+.. SPDX-License-Identifier: GPL-2.0
+.. include:: <isonum.txt>
+
+================
+The AML Debugger
+================
+
+:Copyright: |copy| 2016, Intel Corporation
+:Author: Lv Zheng <lv.zheng@intel.com>
+
+
+This document describes the usage of the AML debugger embedded in the Linux
+kernel.
+
+1. Build the debugger
+=====================
+
+The following kernel configuration items are required to enable the AML
+debugger interface from the Linux kernel::
+
+   CONFIG_ACPI_DEBUGGER=y
+   CONFIG_ACPI_DEBUGGER_USER=m
+
+The userspace utilities can be built from the kernel source tree using
+the following commands::
+
+   $ cd tools
+   $ make acpi
+
+The resultant userspace tool binary is then located at::
+
+   tools/power/acpi/acpidbg
+
+It can be installed to system directories by running "make install" (as a
+sufficiently privileged user).
+
+2. Start the userspace debugger interface
+=========================================
+
+After booting the kernel with the debugger built-in, the debugger can be
+started by using the following commands::
+
+   # mount -t debugfs none /sys/kernel/debug
+   # modprobe acpi_dbg
+   # tools/power/acpi/acpidbg
+
+That spawns the interactive AML debugger environment where you can execute
+debugger commands.
+
+The commands are documented in the "ACPICA Overview and Programmer Reference"
+that can be downloaded from
+
+https://acpica.org/documentation
+
+The detailed debugger commands reference is located in Chapter 12 "ACPICA
+Debugger Reference".  The "help" command can be used for a quick reference.
+
+3. Stop the userspace debugger interface
+========================================
+
+The interactive debugger interface can be closed by pressing Ctrl+C or using
+the "quit" or "exit" commands.  When finished, unload the module with::
+
+   # rmmod acpi_dbg
+
+The module unloading may fail if there is an acpidbg instance running.
+
+4. Run the debugger in a script
+===============================
+
+It may be useful to run the AML debugger in a test script. "acpidbg" supports
+this in a special "batch" mode.  For example, the following command outputs
+the entire ACPI namespace::
+
+   # acpidbg -b "namespace"