iio: proximity: vl53l0x-i2c: claim direct mode for raw readsgrafted

vl53l0x_read_raw() starts a single-shot ranging measurement and reads
back the result. Once the triggered buffer is enabled the sensor runs in
continuous mode and its data-ready interrupt is routed to the trigger,
so a concurrent in_distance_raw read disturbs the streaming setup and
never gets its completion, returning -ETIMEDOUT.

The original submission claimed direct mode here, but it was dropped
during review because the driver had no buffer support at the time [1].
Continuous (buffered) mode was later added without restoring the
claim [2], reintroducing the conflict.

Reject direct reads while buffered capture is active by claiming direct
mode around the measurement, as the vl53l1x sibling already does.

Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support")
Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1]
Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2]
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

1 files changed, 128 insertions, 0 deletions

diff --git a/Documentation/filesystems/befs.rst b/Documentation/filesystems/befs.rst
new file mode 100644
index 000000000..a22f603b2
--- /dev/null
+++ b/Documentation/filesystems/befs.rst
@@ -0,0 +1,128 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=========================
+BeOS filesystem for Linux
+=========================
+
+Document last updated: Dec 6, 2001
+
+Warning
+=======
+Make sure you understand that this is alpha software.  This means that the
+implementation is neither complete nor well-tested.
+
+I DISCLAIM ALL RESPONSIBILITY FOR ANY POSSIBLE BAD EFFECTS OF THIS CODE!
+
+License
+=======
+This software is covered by the GNU General Public License.
+See the file COPYING for the complete text of the license.
+Or the GNU website: <http://www.gnu.org/licenses/licenses.html>
+
+Author
+======
+The largest part of the code written by Will Dyson <will_dyson@pobox.com>
+He has been working on the code since Aug 13, 2001. See the changelog for
+details.
+
+Original Author: Makoto Kato <m_kato@ga2.so-net.ne.jp>
+
+His original code can still be found at:
+<http://hp.vector.co.jp/authors/VA008030/bfs/>
+
+Does anyone know of a more current email address for Makoto? He doesn't
+respond to the address given above...
+
+This filesystem doesn't have a maintainer.
+
+What is this Driver?
+====================
+This module implements the native filesystem of BeOS http://www.beincorporated.com/
+for the linux 2.4.1 and later kernels. Currently it is a read-only
+implementation.
+
+Which is it, BFS or BEFS?
+=========================
+Be, Inc said, "BeOS Filesystem is officially called BFS, not BeFS".
+But Unixware Boot Filesystem is called bfs, too. And they are already in
+the kernel. Because of this naming conflict, on Linux the BeOS
+filesystem is called befs.
+
+How to Install
+==============
+step 1.  Install the BeFS  patch into the source code tree of linux.
+
+Apply the patchfile to your kernel source tree.
+Assuming that your kernel source is in /foo/bar/linux and the patchfile
+is called patch-befs-xxx, you would do the following:
+
+	cd /foo/bar/linux
+	patch -p1 < /path/to/patch-befs-xxx
+
+if the patching step fails (i.e. there are rejected hunks), you can try to
+figure it out yourself (it shouldn't be hard), or mail the maintainer
+(Will Dyson <will_dyson@pobox.com>) for help.
+
+step 2.  Configuration & make kernel
+
+The linux kernel has many compile-time options. Most of them are beyond the
+scope of this document. I suggest the Kernel-HOWTO document as a good general
+reference on this topic. http://www.linuxdocs.org/HOWTOs/Kernel-HOWTO-4.html
+
+However, to use the BeFS module, you must enable it at configure time::
+
+	cd /foo/bar/linux
+	make menuconfig (or xconfig)
+
+The BeFS module is not a standard part of the linux kernel, so you must first
+enable support for experimental code under the "Code maturity level" menu.
+
+Then, under the "Filesystems" menu will be an option called "BeFS
+filesystem (experimental)", or something like that. Enable that option
+(it is fine to make it a module).
+
+Save your kernel configuration and then build your kernel.
+
+step 3.  Install
+
+See the kernel howto <http://www.linux.com/howto/Kernel-HOWTO.html> for
+instructions on this critical step.
+
+Using BFS
+=========
+To use the BeOS filesystem, use filesystem type 'befs'.
+
+ex::
+
+    mount -t befs /dev/fd0 /beos
+
+Mount Options
+=============
+
+=============  ===========================================================
+uid=nnn        All files in the partition will be owned by user id nnn.
+gid=nnn	       All files in the partition will be in group nnn.
+iocharset=xxx  Use xxx as the name of the NLS translation table.
+debug          The driver will output debugging information to the syslog.
+=============  ===========================================================
+
+How to Get Latest Version
+=========================
+
+The latest version is currently available at:
+<http://befs-driver.sourceforge.net/>
+
+Any Known Bugs?
+===============
+As of Jan 20, 2002:
+
+	None
+
+Special Thanks
+==============
+Dominic Giampalo ... Writing "Practical file system design with Be filesystem"
+
+Hiroyuki Yamada  ... Testing LinuxPPC.
+
+
+