x86/kprobes: Fix crash when probing CS CALL instructionsgrafted

When using eBPF to probe CS CALL instructions within a function,
a crash can be triggered.

The eBPF tool probes offset 257 of the __hrtimer_run_queues()
function:

<__hrtimer_run_queues+249>:  nopl   0x0(%rax,%rax,1)
<__hrtimer_run_queues+254>:  mov    %r14,%rdi
<__hrtimer_run_queues+257>:  cs call <__x86_indirect_thunk_r12>
<__hrtimer_run_queues+263>:  mov    %eax,%r12d
<__hrtimer_run_queues+266>:  xchg   %ax,%ax
<__hrtimer_run_queues+268>:  mov    %r13,%rdi

Which triggers this crash:

  BUG: unable to handle page fault for address: 00000000000f41c9
  #PF: supervisor write access in kernel mode
  #PF: error_code(0x0002) - not-present page
  PGD 0 P4D 0
  Oops: 0002 [#1] SMP NOPTI
  CPU: 1 PID: 0 Comm: swapper/1 Kdump: loaded Tainted: P
  RIP: 0010:__hrtimer_run_queues+0x106/0x230

Note that __hrtimer_run_queues+0x106 is __hrtimer_run_queues+262, which is
at the 6th byte of the above CS CALL instruction. Since the CS CALL
instruction occupies 6 bytes, the exception occurred in the middle of that
call instruction.

The root cause is that when using eBPF tools to probe in the middle of a
function, a kprobe with INT3 is used as the underlying implementation.

During single-step emulation of the original CALL instruction,
int3_emulate_call() assumes that the probed CALL instruction is 5 bytes
long. However, the actual CS-prefixed CALL instruction occupies 6 bytes,
so it constructs an incorrect exception return address. When the CPU
returns from the kprobe handler, the next instruction to be executed is at
the address of the last byte of that CS CALL instruction. Coincidentally,
starting from that address, the CPU fetches and decodes a completely
different instruction, which ultimately triggers a kernel crash.

Fix the issue by using the actual instruction length obtained from
the instruction decoder when constructing the exception return
address, rather than relying on the hardcoded CALL_INSN_SIZE macro.

[ mingo: Refined the changelog ]

Fixes: 6256e668b7af ("x86/kprobes: Use int3 instead of debug trap for single-step")
Suggested-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Jinke Han <jinkehan@didiglobal.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Yafang Shao <laoar.shao@gmail.com>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://patch.msgid.link/20260908073742.GA10517@didi-ThinkCentre-M920t-N000

1 files changed, 82 insertions, 0 deletions

diff --git a/Documentation/fb/s3fb.rst b/Documentation/fb/s3fb.rst
new file mode 100644
index 000000000..e809d69c2
--- /dev/null
+++ b/Documentation/fb/s3fb.rst
@@ -0,0 +1,82 @@
+===========================================
+s3fb - fbdev driver for S3 Trio/Virge chips
+===========================================
+
+
+Supported Hardware
+==================
+
+	S3 Trio32
+	S3 Trio64 (and variants V+, UV+, V2/DX, V2/GX)
+	S3 Virge  (and variants VX, DX, GX and GX2+)
+	S3 Plato/PX		(completely untested)
+	S3 Aurora64V+		(completely untested)
+
+	- only PCI bus supported
+	- only BIOS initialized VGA devices supported
+	- probably not working on big endian
+
+I tested s3fb on Trio64 (plain, V+ and V2/DX) and Virge (plain, VX, DX),
+all on i386.
+
+
+Supported Features
+==================
+
+	*  4 bpp pseudocolor modes (with 18bit palette, two variants)
+	*  8 bpp pseudocolor mode (with 18bit palette)
+	* 16 bpp truecolor modes (RGB 555 and RGB 565)
+	* 24 bpp truecolor mode (RGB 888) on (only on Virge VX)
+	* 32 bpp truecolor mode (RGB 888) on (not on Virge VX)
+	* text mode (activated by bpp = 0)
+	* interlaced mode variant (not available in text mode)
+	* doublescan mode variant (not available in text mode)
+	* panning in both directions
+	* suspend/resume support
+	* DPMS support
+
+Text mode is supported even in higher resolutions, but there is limitation to
+lower pixclocks (maximum usually between 50-60 MHz, depending on specific
+hardware, i get best results from plain S3 Trio32 card - about 75 MHz). This
+limitation is not enforced by driver. Text mode supports 8bit wide fonts only
+(hardware limitation) and 16bit tall fonts (driver limitation). Text mode
+support is broken on S3 Trio64 V2/DX.
+
+There are two 4 bpp modes. First mode (selected if nonstd == 0) is mode with
+packed pixels, high nibble first. Second mode (selected if nonstd == 1) is mode
+with interleaved planes (1 byte interleave), MSB first. Both modes support
+8bit wide fonts only (driver limitation).
+
+Suspend/resume works on systems that initialize video card during resume and
+if device is active (for example used by fbcon).
+
+
+Missing Features
+================
+(alias TODO list)
+
+	* secondary (not initialized by BIOS) device support
+	* big endian support
+	* Zorro bus support
+	* MMIO support
+	* 24 bpp mode support on more cards
+	* support for fontwidths != 8 in 4 bpp modes
+	* support for fontheight != 16 in text mode
+	* composite and external sync (is anyone able to test this?)
+	* hardware cursor
+	* video overlay support
+	* vsync synchronization
+	* feature connector support
+	* acceleration support (8514-like 2D, Virge 3D, busmaster transfers)
+	* better values for some magic registers (performance issues)
+
+
+Known bugs
+==========
+
+	* cursor disable in text mode doesn't work
+	* text mode broken on S3 Trio64 V2/DX
+
+
+--
+Ondrej Zajicek <santiago@crfreenet.org>