iio: proximity: vl53l0x-i2c: claim direct mode for raw readsgrafted

vl53l0x_read_raw() starts a single-shot ranging measurement and reads
back the result. Once the triggered buffer is enabled the sensor runs in
continuous mode and its data-ready interrupt is routed to the trigger,
so a concurrent in_distance_raw read disturbs the streaming setup and
never gets its completion, returning -ETIMEDOUT.

The original submission claimed direct mode here, but it was dropped
during review because the driver had no buffer support at the time [1].
Continuous (buffered) mode was later added without restoring the
claim [2], reintroducing the conflict.

Reject direct reads while buffered capture is active by claiming direct
mode around the measurement, as the vl53l1x sibling already does.

Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support")
Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1]
Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2]
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

1 files changed, 79 insertions, 0 deletions

diff --git a/Documentation/fb/deferred_io.rst b/Documentation/fb/deferred_io.rst
new file mode 100644
index 000000000..7fc1933b0
--- /dev/null
+++ b/Documentation/fb/deferred_io.rst
@@ -0,0 +1,79 @@
+===========
+Deferred IO
+===========
+
+Deferred IO is a way to delay and repurpose IO. It uses host memory as a
+buffer and the MMU pagefault as a pretrigger for when to perform the device
+IO. The following example may be a useful explanation of how one such setup
+works:
+
+- userspace app like Xfbdev mmaps framebuffer
+- deferred IO and driver sets up fault and page_mkwrite handlers
+- userspace app tries to write to mmapped vaddress
+- we get pagefault and reach fault handler
+- fault handler finds and returns physical page
+- we get page_mkwrite where we add this page to a list
+- schedule a workqueue task to be run after a delay
+- app continues writing to that page with no additional cost. this is
+  the key benefit.
+- the workqueue task comes in and mkcleans the pages on the list, then
+  completes the work associated with updating the framebuffer. this is
+  the real work talking to the device.
+- app tries to write to the address (that has now been mkcleaned)
+- get pagefault and the above sequence occurs again
+
+As can be seen from above, one benefit is roughly to allow bursty framebuffer
+writes to occur at minimum cost. Then after some time when hopefully things
+have gone quiet, we go and really update the framebuffer which would be
+a relatively more expensive operation.
+
+For some types of nonvolatile high latency displays, the desired image is
+the final image rather than the intermediate stages which is why it's okay
+to not update for each write that is occurring.
+
+It may be the case that this is useful in other scenarios as well. Paul Mundt
+has mentioned a case where it is beneficial to use the page count to decide
+whether to coalesce and issue SG DMA or to do memory bursts.
+
+Another one may be if one has a device framebuffer that is in an usual format,
+say diagonally shifting RGB, this may then be a mechanism for you to allow
+apps to pretend to have a normal framebuffer but reswizzle for the device
+framebuffer at vsync time based on the touched pagelist.
+
+How to use it: (for applications)
+---------------------------------
+No changes needed. mmap the framebuffer like normal and just use it.
+
+How to use it: (for fbdev drivers)
+----------------------------------
+The following example may be helpful.
+
+1. Setup your structure. Eg::
+
+	static struct fb_deferred_io hecubafb_defio = {
+		.delay		= HZ,
+		.deferred_io	= hecubafb_dpy_deferred_io,
+	};
+
+The delay is the minimum delay between when the page_mkwrite trigger occurs
+and when the deferred_io callback is called. The deferred_io callback is
+explained below.
+
+2. Setup your deferred IO callback. Eg::
+
+	static void hecubafb_dpy_deferred_io(struct fb_info *info,
+					     struct list_head *pagelist)
+
+The deferred_io callback is where you would perform all your IO to the display
+device. You receive the pagelist which is the list of pages that were written
+to during the delay. You must not modify this list. This callback is called
+from a workqueue.
+
+3. Call init::
+
+	info->fbdefio = &hecubafb_defio;
+	fb_deferred_io_init(info);
+
+4. Call cleanup::
+
+	fb_deferred_io_cleanup(info);