Merge tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlgrafted

Pull pin control updates from Linus Walleij:
 "Core changes:

   - Use the non-blocking mux_state_try_select() in the generic MUX pin
     control back-end

   - Free pin maps on pinctrl_generic_to_map() failure in the core
     helpers

  New hardware pin control:

   - Qualcomm Maili TLMM SoC, PMG1110 PMIC, and Eliza LPASS LPI TLMM SoC
     (this is for the low power audio, LPASS = Low Power Audio SubSystem
     portions)

   - Upboard support on top of the Intel pin controller

   - Apple T6030 and T6031 support (just compatible strings)

   - Samsung Exynos 8855 SoC

   - Mediatek MT6858 SoC

   - Rockchip RK3308B and RV1106 SoCs

   - Airoha EN7523 and AN7563 SoCs

  Improvements:

   - Qualcomm TLMM GPIOs are unconditionally marked as wakeup capable

   - Qualcomm improvements on top of the Qualcomm PDC (power domain
     controller) irqchip improvements from tglx:s tree

   - Qualcomm IPQ806x and IPQ9650 non-urgent pin grop fixups

   - The NPCM8xx driver has been put into shape fixing many pin and
     group definitions

   - Some non-urgent Tegra 264 pin assignments are fixed up

   - Some non-urgent fixups to Airoha AN7581 and AN7583 registers and
     pin assignments, missing features etc"

* tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (130 commits)
  dt-bindings: pinctrl: Convert TI DA850 pupd to DT schema
  pinctrl: meson: sync some modify from A4
  pinctrl: meson: a4: Add input enable pin configuration
  pinctrl: realtek: rtd1625: remove unused group name spdif_sel
  pinctrl: realtek: rtd1625: fix base_bit for VE4 GPIO 13
  dt-bindings: pinctrl: microchip,pic32mzda-pinctrl: Convert to DT schema
  Revert "Merge branch 'ib-rsk7204' into devel"
  pinctrl: rockchip: Add RV1106 pinctrl support
  dt-bindings: pinctrl: rockchip: Add RV1106 compatible
  pinctrl: rockchip: Decode drive strength in the get function
  pinctrl: fix PINCTRL_GENERIC_MUX not always being selectable
  pinctrl: airoha: add support of an7563 SoC
  dt-bindings: pinctrl: airoha: add support of an7563 pin controller
  pinctrl: airoha: try to find chip scu node by phandle first
  pinctrl: airoha: add support of en7523 SoC
  dt-bindings: pinctrl: airoha: add support of en7523 pin controller
  pinctrl: airoha: an7583: add support for olt pinmux
  pinctrl: airoha: an7583: add support for pon_alt pinmux
  pinctrl: airoha: an7583: add support for npu_uart pinmux
  dt-bindings: pinctrl: airoha: an7583: add missed features
  ...

1 files changed, 104 insertions, 0 deletions

diff --git a/Documentation/driver-api/zorro.rst b/Documentation/driver-api/zorro.rst
new file mode 100644
index 000000000..664072b01
--- /dev/null
+++ b/Documentation/driver-api/zorro.rst
@@ -0,0 +1,104 @@
+========================================
+Writing Device Drivers for Zorro Devices
+========================================
+
+:Author: Written by Geert Uytterhoeven <geert@linux-m68k.org>
+:Last revised: September 5, 2003
+
+
+Introduction
+------------
+
+The Zorro bus is the bus used in the Amiga family of computers. Thanks to
+AutoConfig(tm), it's 100% Plug-and-Play.
+
+There are two types of Zorro buses, Zorro II and Zorro III:
+
+  - The Zorro II address space is 24-bit and lies within the first 16 MB of the
+    Amiga's address map.
+
+  - Zorro III is a 32-bit extension of Zorro II, which is backwards compatible
+    with Zorro II. The Zorro III address space lies outside the first 16 MB.
+
+
+Probing for Zorro Devices
+-------------------------
+
+Zorro devices are found by calling ``zorro_find_device()``, which returns a
+pointer to the ``next`` Zorro device with the specified Zorro ID. A probe loop
+for the board with Zorro ID ``ZORRO_PROD_xxx`` looks like::
+
+    struct zorro_dev *z = NULL;
+
+    while ((z = zorro_find_device(ZORRO_PROD_xxx, z))) {
+	if (!zorro_request_region(z->resource.start+MY_START, MY_SIZE,
+				  "My explanation"))
+	...
+    }
+
+``ZORRO_WILDCARD`` acts as a wildcard and finds any Zorro device. If your driver
+supports different types of boards, you can use a construct like::
+
+    struct zorro_dev *z = NULL;
+
+    while ((z = zorro_find_device(ZORRO_WILDCARD, z))) {
+	if (z->id != ZORRO_PROD_xxx1 && z->id != ZORRO_PROD_xxx2 && ...)
+	    continue;
+	if (!zorro_request_region(z->resource.start+MY_START, MY_SIZE,
+				  "My explanation"))
+	...
+    }
+
+
+Zorro Resources
+---------------
+
+Before you can access a Zorro device's registers, you have to make sure it's
+not yet in use. This is done using the I/O memory space resource management
+functions::
+
+    request_mem_region()
+    release_mem_region()
+
+Shortcuts to claim the whole device's address space are provided as well::
+
+    zorro_request_device
+    zorro_release_device
+
+
+Accessing the Zorro Address Space
+---------------------------------
+
+The address regions in the Zorro device resources are Zorro bus address
+regions. Due to the identity bus-physical address mapping on the Zorro bus,
+they are CPU physical addresses as well.
+
+The treatment of these regions depends on the type of Zorro space:
+
+  - Zorro II address space is always mapped and does not have to be mapped
+    explicitly using z_ioremap().
+    
+    Conversion from bus/physical Zorro II addresses to kernel virtual addresses
+    and vice versa is done using::
+
+	virt_addr = ZTWO_VADDR(bus_addr);
+	bus_addr = ZTWO_PADDR(virt_addr);
+
+  - Zorro III address space must be mapped explicitly using z_ioremap() first
+    before it can be accessed::
+ 
+	virt_addr = z_ioremap(bus_addr, size);
+	...
+	z_iounmap(virt_addr);
+
+
+References
+----------
+
+#. linux/include/linux/zorro.h
+#. linux/include/uapi/linux/zorro.h
+#. linux/include/uapi/linux/zorro_ids.h
+#. linux/arch/m68k/include/asm/zorro.h
+#. linux/drivers/zorro
+#. /proc/bus/zorro
+