Merge tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlgrafted

Pull pin control updates from Linus Walleij:
 "Core changes:

   - Use the non-blocking mux_state_try_select() in the generic MUX pin
     control back-end

   - Free pin maps on pinctrl_generic_to_map() failure in the core
     helpers

  New hardware pin control:

   - Qualcomm Maili TLMM SoC, PMG1110 PMIC, and Eliza LPASS LPI TLMM SoC
     (this is for the low power audio, LPASS = Low Power Audio SubSystem
     portions)

   - Upboard support on top of the Intel pin controller

   - Apple T6030 and T6031 support (just compatible strings)

   - Samsung Exynos 8855 SoC

   - Mediatek MT6858 SoC

   - Rockchip RK3308B and RV1106 SoCs

   - Airoha EN7523 and AN7563 SoCs

  Improvements:

   - Qualcomm TLMM GPIOs are unconditionally marked as wakeup capable

   - Qualcomm improvements on top of the Qualcomm PDC (power domain
     controller) irqchip improvements from tglx:s tree

   - Qualcomm IPQ806x and IPQ9650 non-urgent pin grop fixups

   - The NPCM8xx driver has been put into shape fixing many pin and
     group definitions

   - Some non-urgent Tegra 264 pin assignments are fixed up

   - Some non-urgent fixups to Airoha AN7581 and AN7583 registers and
     pin assignments, missing features etc"

* tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (130 commits)
  dt-bindings: pinctrl: Convert TI DA850 pupd to DT schema
  pinctrl: meson: sync some modify from A4
  pinctrl: meson: a4: Add input enable pin configuration
  pinctrl: realtek: rtd1625: remove unused group name spdif_sel
  pinctrl: realtek: rtd1625: fix base_bit for VE4 GPIO 13
  dt-bindings: pinctrl: microchip,pic32mzda-pinctrl: Convert to DT schema
  Revert "Merge branch 'ib-rsk7204' into devel"
  pinctrl: rockchip: Add RV1106 pinctrl support
  dt-bindings: pinctrl: rockchip: Add RV1106 compatible
  pinctrl: rockchip: Decode drive strength in the get function
  pinctrl: fix PINCTRL_GENERIC_MUX not always being selectable
  pinctrl: airoha: add support of an7563 SoC
  dt-bindings: pinctrl: airoha: add support of an7563 pin controller
  pinctrl: airoha: try to find chip scu node by phandle first
  pinctrl: airoha: add support of en7523 SoC
  dt-bindings: pinctrl: airoha: add support of en7523 pin controller
  pinctrl: airoha: an7583: add support for olt pinmux
  pinctrl: airoha: an7583: add support for pon_alt pinmux
  pinctrl: airoha: an7583: add support for npu_uart pinmux
  dt-bindings: pinctrl: airoha: an7583: add missed features
  ...

1 files changed, 159 insertions, 0 deletions

diff --git a/Documentation/driver-api/usb/callbacks.rst b/Documentation/driver-api/usb/callbacks.rst
new file mode 100644
index 000000000..927da49b8
--- /dev/null
+++ b/Documentation/driver-api/usb/callbacks.rst
@@ -0,0 +1,159 @@
+USB core callbacks
+~~~~~~~~~~~~~~~~~~
+
+What callbacks will usbcore do?
+===============================
+
+Usbcore will call into a driver through callbacks defined in the driver
+structure and through the completion handler of URBs a driver submits.
+Only the former are in the scope of this document. These two kinds of
+callbacks are completely independent of each other. Information on the
+completion callback can be found in :ref:`usb-urb`.
+
+The callbacks defined in the driver structure are:
+
+1. Hotplugging callbacks:
+
+ - @probe:
+	Called to see if the driver is willing to manage a particular
+	interface on a device.
+
+ - @disconnect:
+	Called when the interface is no longer accessible, usually
+	because its device has been (or is being) disconnected or the
+	driver module is being unloaded.
+
+2. Odd backdoor through usbfs:
+
+ - @ioctl:
+	Used for drivers that want to talk to userspace through
+	the "usbfs" filesystem.  This lets devices provide ways to
+	expose information to user space regardless of where they
+	do (or don't) show up otherwise in the filesystem.
+
+3. Power management (PM) callbacks:
+
+ - @suspend:
+	Called when the device is going to be suspended.
+
+ - @resume:
+	Called when the device is being resumed.
+
+ - @reset_resume:
+	Called when the suspended device has been reset instead
+	of being resumed.
+
+4. Device level operations:
+
+ - @pre_reset:
+	Called when the device is about to be reset.
+
+ - @post_reset:
+	Called after the device has been reset
+
+The ioctl interface (2) should be used only if you have a very good
+reason. Sysfs is preferred these days. The PM callbacks are covered
+separately in :ref:`usb-power-management`.
+
+Calling conventions
+===================
+
+All callbacks are mutually exclusive. There's no need for locking
+against other USB callbacks. All callbacks are called from a task
+context. You may sleep. However, it is important that all sleeps have a
+small fixed upper limit in time. In particular you must not call out to
+user space and await results.
+
+Hotplugging callbacks
+=====================
+
+These callbacks are intended to associate and disassociate a driver with
+an interface. A driver's bond to an interface is exclusive.
+
+The probe() callback
+--------------------
+
+::
+
+  int (*probe) (struct usb_interface *intf,
+		const struct usb_device_id *id);
+
+Accept or decline an interface. If you accept the device return 0,
+otherwise -ENODEV or -ENXIO. Other error codes should be used only if a
+genuine error occurred during initialisation which prevented a driver
+from accepting a device that would else have been accepted.
+You are strongly encouraged to use usbcore's facility,
+usb_set_intfdata(), to associate a data structure with an interface, so
+that you know which internal state and identity you associate with a
+particular interface. The device will not be suspended and you may do IO
+to the interface you are called for and endpoint 0 of the device. Device
+initialisation that doesn't take too long is a good idea here.
+
+The disconnect() callback
+-------------------------
+
+::
+
+  void (*disconnect) (struct usb_interface *intf);
+
+This callback is a signal to break any connection with an interface.
+You are not allowed any IO to a device after returning from this
+callback. You also may not do any other operation that may interfere
+with another driver bound to the interface, eg. a power management
+operation. Outstanding operations on the device must be completed or
+aborted before this callback may return.
+
+If you are called due to a physical disconnection, all your URBs will be
+killed by usbcore. Note that in this case disconnect will be called some
+time after the physical disconnection. Thus your driver must be prepared
+to deal with failing IO even prior to the callback.
+
+Device level callbacks
+======================
+
+pre_reset
+---------
+
+::
+
+  int (*pre_reset)(struct usb_interface *intf);
+
+A driver or user space is triggering a reset on the device which
+contains the interface passed as an argument. Cease IO, wait for all
+outstanding URBs to complete, and save any device state you need to
+restore.  No more URBs may be submitted until the post_reset method
+is called.
+
+If you need to allocate memory here, use GFP_NOIO or GFP_ATOMIC, if you
+are in atomic context.
+
+post_reset
+----------
+
+::
+
+  int (*post_reset)(struct usb_interface *intf);
+
+The reset has completed.  Restore any saved device state and begin
+using the device again.
+
+If you need to allocate memory here, use GFP_NOIO or GFP_ATOMIC, if you
+are in atomic context.
+
+Call sequences
+==============
+
+No callbacks other than probe will be invoked for an interface
+that isn't bound to your driver.
+
+Probe will never be called for an interface bound to a driver.
+Hence following a successful probe, disconnect will be called
+before there is another probe for the same interface.
+
+Once your driver is bound to an interface, disconnect can be
+called at any time except in between pre_reset and post_reset.
+pre_reset is always followed by post_reset, even if the reset
+failed or the device has been unplugged.
+
+suspend is always followed by one of: resume, reset_resume, or
+disconnect.