iio: proximity: vl53l0x-i2c: claim direct mode for raw readsgrafted

vl53l0x_read_raw() starts a single-shot ranging measurement and reads
back the result. Once the triggered buffer is enabled the sensor runs in
continuous mode and its data-ready interrupt is routed to the trigger,
so a concurrent in_distance_raw read disturbs the streaming setup and
never gets its completion, returning -ETIMEDOUT.

The original submission claimed direct mode here, but it was dropped
during review because the driver had no buffer support at the time [1].
Continuous (buffered) mode was later added without restoring the
claim [2], reintroducing the conflict.

Reject direct reads while buffered capture is active by claiming direct
mode around the measurement, as the vl53l1x sibling already does.

Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support")
Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1]
Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2]
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

1 files changed, 86 insertions, 0 deletions

diff --git a/Documentation/driver-api/sync_file.rst b/Documentation/driver-api/sync_file.rst
new file mode 100644
index 000000000..496fb2c3b
--- /dev/null
+++ b/Documentation/driver-api/sync_file.rst
@@ -0,0 +1,86 @@
+===================
+Sync File API Guide
+===================
+
+:Author: Gustavo Padovan <gustavo at padovan dot org>
+
+This document serves as a guide for device drivers writers on what the
+sync_file API is, and how drivers can support it. Sync file is the carrier of
+the fences(struct dma_fence) that are needed to synchronize between drivers or
+across process boundaries.
+
+The sync_file API is meant to be used to send and receive fence information
+to/from userspace. It enables userspace to do explicit fencing, where instead
+of attaching a fence to the buffer a producer driver (such as a GPU or V4L
+driver) sends the fence related to the buffer to userspace via a sync_file.
+
+The sync_file then can be sent to the consumer (DRM driver for example), that
+will not use the buffer for anything before the fence(s) signals, i.e., the
+driver that issued the fence is not using/processing the buffer anymore, so it
+signals that the buffer is ready to use. And vice-versa for the consumer ->
+producer part of the cycle.
+
+Sync files allows userspace awareness on buffer sharing synchronization between
+drivers.
+
+Sync file was originally added in the Android kernel but current Linux Desktop
+can benefit a lot from it.
+
+in-fences and out-fences
+------------------------
+
+Sync files can go either to or from userspace. When a sync_file is sent from
+the driver to userspace we call the fences it contains 'out-fences'. They are
+related to a buffer that the driver is processing or is going to process, so
+the driver creates an out-fence to be able to notify, through
+dma_fence_signal(), when it has finished using (or processing) that buffer.
+Out-fences are fences that the driver creates.
+
+On the other hand if the driver receives fence(s) through a sync_file from
+userspace we call these fence(s) 'in-fences'. Receiving in-fences means that
+we need to wait for the fence(s) to signal before using any buffer related to
+the in-fences.
+
+Creating Sync Files
+-------------------
+
+When a driver needs to send an out-fence userspace it creates a sync_file.
+
+Interface::
+
+	struct sync_file *sync_file_create(struct dma_fence *fence);
+
+The caller pass the out-fence and gets back the sync_file. That is just the
+first step, next it needs to install an fd on sync_file->file. So it gets an
+fd::
+
+	fd = get_unused_fd_flags(O_CLOEXEC);
+
+and installs it on sync_file->file::
+
+	fd_install(fd, sync_file->file);
+
+The sync_file fd now can be sent to userspace.
+
+If the creation process fail, or the sync_file needs to be released by any
+other reason fput(sync_file->file) should be used.
+
+Receiving Sync Files from Userspace
+-----------------------------------
+
+When userspace needs to send an in-fence to the driver it passes file descriptor
+of the Sync File to the kernel. The kernel can then retrieve the fences
+from it.
+
+Interface::
+
+	struct dma_fence *sync_file_get_fence(int fd);
+
+
+The returned reference is owned by the caller and must be disposed of
+afterwards using dma_fence_put(). In case of error, a NULL is returned instead.
+
+References:
+
+1. struct sync_file in include/linux/sync_file.h
+2. All interfaces mentioned above defined in include/linux/sync_file.h