virtio_blk: set the zone write granularitygrafted

virtblk_read_zoned_limits() reads the write granularity that the device
reports in virtio_blk_zoned_characteristics and assigns it to the
physical block size and to io_min, but never to the limit that is named
after it. queue_limits.zone_write_granularity is left at zero, so
blk_validate_zoned_limits() raises it to the logical block size:

	if (lim->zone_write_granularity < lim->logical_block_size)
		lim->zone_write_granularity = lim->logical_block_size;

A device that reports a granularity coarser than its logical block size,
which is what the field exists to express, therefore has it silently
reduced. A 512e host managed disk passed through to a guest reports a
logical block size of 512 and a write granularity of 4096, and the guest
ends up with a zone write granularity of 512.

bio_split_alignment() returns lim->zone_write_granularity if it is non-zero
and bio_split_io_at() may split a bio with as per bio_split_alignment().
This can real to the write getting rejected by the host drive, as the write
is not aligned to the physical block size.

zonefs also takes its block size from bdev_zone_write_granularity(), so it
would incorrectly use 512 on a disk that requires 4096.

sd_zbc_read_zones() sets the limit from the physical block size for the
same reason. NVMe ZNS and null_blk leave it unset, but the fallback
gives the right answer for them, as their write granularity is the
logical block size. virtio carries a separate value that may exceed it.

Set the zone write granularity from the value that the device reports.

Fixes: 95bfec41bd3d ("virtio-blk: add support for zoned block devices")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://patch.msgid.link/20260918140641.2031075-2-cassel@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

1 files changed, 86 insertions, 0 deletions

diff --git a/Documentation/driver-api/sync_file.rst b/Documentation/driver-api/sync_file.rst
new file mode 100644
index 000000000..496fb2c3b
--- /dev/null
+++ b/Documentation/driver-api/sync_file.rst
@@ -0,0 +1,86 @@
+===================
+Sync File API Guide
+===================
+
+:Author: Gustavo Padovan <gustavo at padovan dot org>
+
+This document serves as a guide for device drivers writers on what the
+sync_file API is, and how drivers can support it. Sync file is the carrier of
+the fences(struct dma_fence) that are needed to synchronize between drivers or
+across process boundaries.
+
+The sync_file API is meant to be used to send and receive fence information
+to/from userspace. It enables userspace to do explicit fencing, where instead
+of attaching a fence to the buffer a producer driver (such as a GPU or V4L
+driver) sends the fence related to the buffer to userspace via a sync_file.
+
+The sync_file then can be sent to the consumer (DRM driver for example), that
+will not use the buffer for anything before the fence(s) signals, i.e., the
+driver that issued the fence is not using/processing the buffer anymore, so it
+signals that the buffer is ready to use. And vice-versa for the consumer ->
+producer part of the cycle.
+
+Sync files allows userspace awareness on buffer sharing synchronization between
+drivers.
+
+Sync file was originally added in the Android kernel but current Linux Desktop
+can benefit a lot from it.
+
+in-fences and out-fences
+------------------------
+
+Sync files can go either to or from userspace. When a sync_file is sent from
+the driver to userspace we call the fences it contains 'out-fences'. They are
+related to a buffer that the driver is processing or is going to process, so
+the driver creates an out-fence to be able to notify, through
+dma_fence_signal(), when it has finished using (or processing) that buffer.
+Out-fences are fences that the driver creates.
+
+On the other hand if the driver receives fence(s) through a sync_file from
+userspace we call these fence(s) 'in-fences'. Receiving in-fences means that
+we need to wait for the fence(s) to signal before using any buffer related to
+the in-fences.
+
+Creating Sync Files
+-------------------
+
+When a driver needs to send an out-fence userspace it creates a sync_file.
+
+Interface::
+
+	struct sync_file *sync_file_create(struct dma_fence *fence);
+
+The caller pass the out-fence and gets back the sync_file. That is just the
+first step, next it needs to install an fd on sync_file->file. So it gets an
+fd::
+
+	fd = get_unused_fd_flags(O_CLOEXEC);
+
+and installs it on sync_file->file::
+
+	fd_install(fd, sync_file->file);
+
+The sync_file fd now can be sent to userspace.
+
+If the creation process fail, or the sync_file needs to be released by any
+other reason fput(sync_file->file) should be used.
+
+Receiving Sync Files from Userspace
+-----------------------------------
+
+When userspace needs to send an in-fence to the driver it passes file descriptor
+of the Sync File to the kernel. The kernel can then retrieve the fences
+from it.
+
+Interface::
+
+	struct dma_fence *sync_file_get_fence(int fd);
+
+
+The returned reference is owned by the caller and must be disposed of
+afterwards using dma_fence_put(). In case of error, a NULL is returned instead.
+
+References:
+
+1. struct sync_file in include/linux/sync_file.h
+2. All interfaces mentioned above defined in include/linux/sync_file.h