Merge tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlgrafted

Pull pin control updates from Linus Walleij:
 "Core changes:

   - Use the non-blocking mux_state_try_select() in the generic MUX pin
     control back-end

   - Free pin maps on pinctrl_generic_to_map() failure in the core
     helpers

  New hardware pin control:

   - Qualcomm Maili TLMM SoC, PMG1110 PMIC, and Eliza LPASS LPI TLMM SoC
     (this is for the low power audio, LPASS = Low Power Audio SubSystem
     portions)

   - Upboard support on top of the Intel pin controller

   - Apple T6030 and T6031 support (just compatible strings)

   - Samsung Exynos 8855 SoC

   - Mediatek MT6858 SoC

   - Rockchip RK3308B and RV1106 SoCs

   - Airoha EN7523 and AN7563 SoCs

  Improvements:

   - Qualcomm TLMM GPIOs are unconditionally marked as wakeup capable

   - Qualcomm improvements on top of the Qualcomm PDC (power domain
     controller) irqchip improvements from tglx:s tree

   - Qualcomm IPQ806x and IPQ9650 non-urgent pin grop fixups

   - The NPCM8xx driver has been put into shape fixing many pin and
     group definitions

   - Some non-urgent Tegra 264 pin assignments are fixed up

   - Some non-urgent fixups to Airoha AN7581 and AN7583 registers and
     pin assignments, missing features etc"

* tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (130 commits)
  dt-bindings: pinctrl: Convert TI DA850 pupd to DT schema
  pinctrl: meson: sync some modify from A4
  pinctrl: meson: a4: Add input enable pin configuration
  pinctrl: realtek: rtd1625: remove unused group name spdif_sel
  pinctrl: realtek: rtd1625: fix base_bit for VE4 GPIO 13
  dt-bindings: pinctrl: microchip,pic32mzda-pinctrl: Convert to DT schema
  Revert "Merge branch 'ib-rsk7204' into devel"
  pinctrl: rockchip: Add RV1106 pinctrl support
  dt-bindings: pinctrl: rockchip: Add RV1106 compatible
  pinctrl: rockchip: Decode drive strength in the get function
  pinctrl: fix PINCTRL_GENERIC_MUX not always being selectable
  pinctrl: airoha: add support of an7563 SoC
  dt-bindings: pinctrl: airoha: add support of an7563 pin controller
  pinctrl: airoha: try to find chip scu node by phandle first
  pinctrl: airoha: add support of en7523 SoC
  dt-bindings: pinctrl: airoha: add support of en7523 pin controller
  pinctrl: airoha: an7583: add support for olt pinmux
  pinctrl: airoha: an7583: add support for pon_alt pinmux
  pinctrl: airoha: an7583: add support for npu_uart pinmux
  dt-bindings: pinctrl: airoha: an7583: add missed features
  ...

1 files changed, 102 insertions, 0 deletions

diff --git a/Documentation/driver-api/switchtec.rst b/Documentation/driver-api/switchtec.rst
new file mode 100644
index 000000000..7611fdc53
--- /dev/null
+++ b/Documentation/driver-api/switchtec.rst
@@ -0,0 +1,102 @@
+========================
+Linux Switchtec Support
+========================
+
+Microsemi's "Switchtec" line of PCI switch devices is already
+supported by the kernel with standard PCI switch drivers. However, the
+Switchtec device advertises a special management endpoint which
+enables some additional functionality. This includes:
+
+* Packet and Byte Counters
+* Firmware Upgrades
+* Event and Error logs
+* Querying port link status
+* Custom user firmware commands
+
+The switchtec kernel module implements this functionality.
+
+
+Interface
+=========
+
+The primary means of communicating with the Switchtec management firmware is
+through the Memory-mapped Remote Procedure Call (MRPC) interface.
+Commands are submitted to the interface with a 4-byte command
+identifier and up to 1KB of command specific data. The firmware will
+respond with a 4-byte return code and up to 1KB of command-specific
+data. The interface only processes a single command at a time.
+
+
+Userspace Interface
+===================
+
+The MRPC interface will be exposed to userspace through a simple char
+device: /dev/switchtec#, one for each management endpoint in the system.
+
+The char device has the following semantics:
+
+* A write must consist of at least 4 bytes and no more than 1028 bytes.
+  The first 4 bytes will be interpreted as the Command ID and the
+  remainder will be used as the input data. A write will send the
+  command to the firmware to begin processing.
+
+* Each write must be followed by exactly one read. Any double write will
+  produce an error and any read that doesn't follow a write will
+  produce an error.
+
+* A read will block until the firmware completes the command and return
+  the 4-byte Command Return Value plus up to 1024 bytes of output
+  data. (The length will be specified by the size parameter of the read
+  call -- reading less than 4 bytes will produce an error.)
+
+* The poll call will also be supported for userspace applications that
+  need to do other things while waiting for the command to complete.
+
+The following IOCTLs are also supported by the device:
+
+* SWITCHTEC_IOCTL_FLASH_INFO - Retrieve firmware length and number
+  of partitions in the device.
+
+* SWITCHTEC_IOCTL_FLASH_PART_INFO - Retrieve address and lengeth for
+  any specified partition in flash.
+
+* SWITCHTEC_IOCTL_EVENT_SUMMARY - Read a structure of bitmaps
+  indicating all uncleared events.
+
+* SWITCHTEC_IOCTL_EVENT_CTL - Get the current count, clear and set flags
+  for any event. This ioctl takes in a switchtec_ioctl_event_ctl struct
+  with the event_id, index and flags set (index being the partition or PFF
+  number for non-global events). It returns whether the event has
+  occurred, the number of times and any event specific data. The flags
+  can be used to clear the count or enable and disable actions to
+  happen when the event occurs.
+  By using the SWITCHTEC_IOCTL_EVENT_FLAG_EN_POLL flag,
+  you can set an event to trigger a poll command to return with
+  POLLPRI. In this way, userspace can wait for events to occur.
+
+* SWITCHTEC_IOCTL_PFF_TO_PORT and SWITCHTEC_IOCTL_PORT_TO_PFF convert
+  between PCI Function Framework number (used by the event system)
+  and Switchtec Logic Port ID and Partition number (which is more
+  user friendly).
+
+
+Non-Transparent Bridge (NTB) Driver
+===================================
+
+An NTB hardware driver is provided for the Switchtec hardware in
+ntb_hw_switchtec. Currently, it only supports switches configured with
+exactly 2 NT partitions and zero or more non-NT partitions. It also requires
+the following configuration settings:
+
+* Both NT partitions must be able to access each other's GAS spaces.
+  Thus, the bits in the GAS Access Vector under Management Settings
+  must be set to support this.
+* Kernel configuration MUST include support for NTB (CONFIG_NTB needs
+  to be set)
+
+NT EP BAR 2 will be dynamically configured as a Direct Window, and
+the configuration file does not need to configure it explicitly.
+
+Please refer to Documentation/driver-api/ntb.rst in Linux source tree for an overall
+understanding of the Linux NTB stack. ntb_hw_switchtec works as an NTB
+Hardware Driver in this stack.