drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validationgrafted

amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and
uses the first encoding that validates. YCbCr 4:4:4 is listed before
RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the
"color format" property is left at AUTO, even though RGB fits the same
link.

That contradicts the documented AUTO behaviour for HDMI in enum
drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when
the bandwidth is not available or the mode is 4:2:0-only), which the
amdgpu implementation of the property also describes. It also leaves
the "Broadcast RGB" property without effect on such sinks, since the
quantization range it selects only applies to RGB output.

Try RGB first. The mask still holds every encoding the sink supports,
so a mode that cannot carry RGB falls back exactly as before.

For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced
through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI
sink that advertised it.

Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation")
Suggested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Assisted-by: Claude Code:claude-fable-5-1
Signed-off-by: Adrian Betschart <adrian.betschart@cinemaone.ch>
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7)

1 files changed, 53 insertions, 0 deletions

diff --git a/Documentation/driver-api/spi.rst b/Documentation/driver-api/spi.rst
new file mode 100644
index 000000000..74eca6735
--- /dev/null
+++ b/Documentation/driver-api/spi.rst
@@ -0,0 +1,53 @@
+Serial Peripheral Interface (SPI)
+=================================
+
+SPI is the "Serial Peripheral Interface", widely used with embedded
+systems because it is a simple and efficient interface: basically a
+multiplexed shift register. Its three signal wires hold a clock (SCK,
+often in the range of 1-20 MHz), a "Master Out, Slave In" (MOSI) data
+line, and a "Master In, Slave Out" (MISO) data line. SPI is a full
+duplex protocol; for each bit shifted out the MOSI line (one per clock)
+another is shifted in on the MISO line. Those bits are assembled into
+words of various sizes on the way to and from system memory. An
+additional chipselect line is usually active-low (nCS); four signals are
+normally used for each peripheral, plus sometimes an interrupt.
+
+The SPI bus facilities listed here provide a generalized interface to
+declare SPI buses and devices, manage them according to the standard
+Linux driver model, and perform input/output operations. At this time,
+only "master" side interfaces are supported, where Linux talks to SPI
+peripherals and does not implement such a peripheral itself. (Interfaces
+to support implementing SPI slaves would necessarily look different.)
+
+The programming interface is structured around two kinds of driver, and
+two kinds of device. A "Controller Driver" abstracts the controller
+hardware, which may be as simple as a set of GPIO pins or as complex as
+a pair of FIFOs connected to dual DMA engines on the other side of the
+SPI shift register (maximizing throughput). Such drivers bridge between
+whatever bus they sit on (often the platform bus) and SPI, and expose
+the SPI side of their device as a :c:type:`struct spi_controller
+<spi_controller>`. SPI devices are children of that master,
+represented as a :c:type:`struct spi_device <spi_device>` and
+manufactured from :c:type:`struct spi_board_info
+<spi_board_info>` descriptors which are usually provided by
+board-specific initialization code. A :c:type:`struct spi_driver
+<spi_driver>` is called a "Protocol Driver", and is bound to a
+spi_device using normal driver model calls.
+
+The I/O model is a set of queued messages. Protocol drivers submit one
+or more :c:type:`struct spi_message <spi_message>` objects,
+which are processed and completed asynchronously. (There are synchronous
+wrappers, however.) Messages are built from one or more
+:c:type:`struct spi_transfer <spi_transfer>` objects, each of
+which wraps a full duplex SPI transfer. A variety of protocol tweaking
+options are needed, because different chips adopt very different
+policies for how they use the bits transferred with SPI.
+
+.. kernel-doc:: include/linux/spi/spi.h
+   :internal:
+
+.. kernel-doc:: drivers/spi/spi.c
+   :functions: spi_register_board_info
+
+.. kernel-doc:: drivers/spi/spi.c
+   :export: