iio: proximity: vl53l0x-i2c: claim direct mode for raw readsgrafted

vl53l0x_read_raw() starts a single-shot ranging measurement and reads
back the result. Once the triggered buffer is enabled the sensor runs in
continuous mode and its data-ready interrupt is routed to the trigger,
so a concurrent in_distance_raw read disturbs the streaming setup and
never gets its completion, returning -ETIMEDOUT.

The original submission claimed direct mode here, but it was dropped
during review because the driver had no buffer support at the time [1].
Continuous (buffered) mode was later added without restoring the
claim [2], reintroducing the conflict.

Reject direct reads while buffered capture is active by claiming direct
mode around the measurement, as the vl53l1x sibling already does.

Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support")
Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1]
Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2]
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

1 files changed, 74 insertions, 0 deletions

diff --git a/Documentation/driver-api/sm501.rst b/Documentation/driver-api/sm501.rst
new file mode 100644
index 000000000..882507453
--- /dev/null
+++ b/Documentation/driver-api/sm501.rst
@@ -0,0 +1,74 @@
+.. include:: <isonum.txt>
+
+============
+SM501 Driver
+============
+
+:Copyright: |copy| 2006, 2007 Simtec Electronics
+
+The Silicon Motion SM501 multimedia companion chip is a multifunction device
+which may provide numerous interfaces including USB host controller USB gadget,
+asynchronous serial ports, audio functions, and a dual display video interface.
+The device may be connected by PCI or local bus with varying functions enabled.
+
+Core
+----
+
+The core driver in drivers/mfd provides common services for the
+drivers which manage the specific hardware blocks. These services
+include locking for common registers, clock control and resource
+management.
+
+The core registers drivers for both PCI and generic bus based
+chips via the platform device and driver system.
+
+On detection of a device, the core initialises the chip (which may
+be specified by the platform data) and then exports the selected
+peripheral set as platform devices for the specific drivers.
+
+The core re-uses the platform device system as the platform device
+system provides enough features to support the drivers without the
+need to create a new bus-type and the associated code to go with it.
+
+
+Resources
+---------
+
+Each peripheral has a view of the device which is implicitly narrowed to
+the specific set of resources that peripheral requires in order to
+function correctly.
+
+The centralised memory allocation allows the driver to ensure that the
+maximum possible resource allocation can be made to the video subsystem
+as this is by-far the most resource-sensitive of the on-chip functions.
+
+The primary issue with memory allocation is that of moving the video
+buffers once a display mode is chosen. Indeed when a video mode change
+occurs the memory footprint of the video subsystem changes.
+
+Since video memory is difficult to move without changing the display
+(unless sufficient contiguous memory can be provided for the old and new
+modes simultaneously) the video driver fully utilises the memory area
+given to it by aligning fb0 to the start of the area and fb1 to the end
+of it. Any memory left over in the middle is used for the acceleration
+functions, which are transient and thus their location is less critical
+as it can be moved.
+
+
+Configuration
+-------------
+
+The platform device driver uses a set of platform data to pass
+configurations through to the core and the subsidiary drivers
+so that there can be support for more than one system carrying
+an SM501 built into a single kernel image.
+
+The PCI driver assumes that the PCI card behaves as per the Silicon
+Motion reference design.
+
+There is an errata (AB-5) affecting the selection of the
+of the M1XCLK and M1CLK frequencies. These two clocks
+must be sourced from the same PLL, although they can then
+be divided down individually. If this is not set, then SM501 may
+lock and hang the whole system. The driver will refuse to
+attach if the PLL selection is different.